Manuel d'utilisation / d'entretien du produit M671111 du fabricant Huffy
Aller à la page of 25
1 07/05 ID# M671111 © COPYRIGHT 2005 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 ID# M671111 07/05 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates.
07/05 ID# M671111 3 Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
4 ID# M671111 07/05 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
07/05 ID# M671111 5 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p arts are p acked inside. NOTICE T O ASSEMBLERS ALL Huffy Sport s Basketball Systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to the instructions.
6 ID# M671111 07/05 Get to know the basic parts of your basketball system..... FRONT P ANEL BACKBOARD FRONT RIM BASE POLE.
07/05 ID# M671111 7 P ARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 203470 Washer, Flat, 1.5” O.D. 2 1 806620 Base Assembly 3 1 804833 Exacta Height Assembly 4 1 908006 To.
8 ID# M671111 07/05 HARDW ARE IDENTIFIER (BOL TS & SCREWS) * You may have extra parts with this model. #7 (2) #40 (1) #39 (2) Item #23 (1) #29 (6) #16 (2) #12 (1) #44 (4)* #19 (4) #47 (4) #49 (1) .
07/05 ID# M671111 9 HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS CAPS & CLIPS) HARDW ARE IDENTIFIER (OTHER) #13 (2) #20 (2) #26 (4) #30 (4) #36 (2) #1 1(4)* #1.
10 ID# M671111 07/05 T OOLS REQUIRED FOR THIS SECTION SECTION A: ASSEMBLE THE BASE And/Or: This is what your system will look like when you’ve finished this section: 1/2” 9/16” Wrenches (2) 1/2.
07/05 ID# M671111 11 1A. Check the following pre-assembled base areas for tightness: Eye bolt s P/N 203452, W asher P/N 203218 , Nut P/N 203100, Carriage Bolts P/N 203223 .
12 ID# M671111 07/05 Check the following pre-assembled handle areas for tightness: Screw P/N 204803, Nut P/N 203100, Carriage Bolt s P/N 203103 . Carriage Bolt P/N 203103 Nut P/N 203100 Nut P/N 203100.
07/05 ID# M671111 13 6 5 4 3. WOOD SCRAP (NOT SUPPLIED) 5 4 While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole.
14 ID# M671111 07/05 4. 4 5 6 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE TROUGH TROUGH TROUGH Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown.
07/05 ID# M671111 15 9 7 6 9 7 13 8 45 5. Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut should be tightened until flush (even) with locknuts outer edge. 12 10 6 7. Secure cover to rod (9) using washers (45) nuts (8) and nut covers (13) as shown.
16 ID# M671111 07/05 8 . Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolt s (16) as shown. T ighten flange nuts (14) completely . 4 42 14 14 15 16 16 9. Att ach sp acers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), and nuts (8) as shown.
07/05 ID# M671111 17 Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. 10 . 15 14 24 22 22 25 23 FIG . A 25 24 Loop end of pin lanyard (25) over carriage bolt (23) as it p asses through the pole mount bracket (15) during this assembly .
18 ID# M671111 07/05 TOOLS REQUIRED FOR THIS SECTION SECTION B: A TT ACH THE BACKBOARD Phillip s- Head Screwdriver This is what your system will look like when you’ve finished this section: W renche.
07/05 ID# M671111 19 Assemble backboard brackets (27) using bolt s (43), and nuts (8) as shown. 1. 27 43 8 8 43.
20 ID# M671111 07/05 2. Attach lower elevator tubes (32) and counter balance springs (33) to backboard support brackets (27) using sp acers (26), bolt (29), and nut (31) as shown.
07/05 ID# M671111 21 3. 50 52 1 48 49 Inst all Slam Jam Rim to Backboard 34 51 49 1 52 A B C D E A Fit rim (34) securely into bracket (48) as shown. Allow T -bolt (49) to slip through center hole in rim (34). B Install reinforcement bracket (50) onto T -bolt (49) as shown.
22 ID# M671111 07/05 4. Attach upper elevator tubes (35) to backboard support bracket s (27) using spacers (26 & 1 1), bolt (29), and nut (31) as shown.
07/05 ID# M671111 23 31 31 40 38 32 4 37 37 29 30 32 30 29 32 29 35 30 31 31 35 30 37 36 36 5. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (38). Use caution; elevator assembly is heavy . 6. 7.
24 ID# M671111 07/05 8. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 9. Roll completed assembly to desired position.
07/05 ID# M671111 25 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Huffy M671111 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Huffy M671111 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Huffy M671111, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Huffy M671111 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Huffy M671111, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Huffy M671111.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Huffy M671111. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Huffy M671111 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
