Manuel d'utilisation / d'entretien du produit hn200w du fabricant HP
Aller à la page of 94
hp digital home networking wireless gateway model hn200w.
wireless gateway 2 acknowledgements and notices hewlett-packard company notices The information contained in this document is subject to change without notice. Hewlett-Packard (HP) makes no warranty of any kind with regard to this material including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
3 contents introduction ............................................................. 5 hp digital home networking wireless gateway .................... 5 features ......................................................................... 6 getting to know the wireless gateway .
wireless gateway 4 troubleshooting ...................................................... 49 appendix: the expert interface ................................. 51 advanced administration ............................................... 51 screens and functions .
5 intr oduction hp digital home networking wireless gateway Congratulations on your purchase of the HP Digital Home Networking Wireless Gateway . The W ireless Gateway is the per fect solution for connecting your wireless network to a high-speed broadband cable modem or Digital Subscriber Line (DSL) Internet connection.
wireless gateway 6 features ❑ Allows shared Internet access with all PCs on a Local Area Network (LAN) ❑ Compatible with other wireless equipment that is IEEE 802.
7 getting to know the wireless gateway wireless gateway rear panel All Gateway connections are made on the rear panel. wireless gateway ports Wireless Gateway Rear Panel W AN Y ou will connect the DSL or cable modem to the Wide Area Network (W AN) port.
wireless gateway 8 reset button T o refresh Gateway connections and attempt to fix routing problems, ver y briefly depress the Reset button with a paper clip.
wireless gateway’ s front panel LEDs 9 wireless gateway’ s fr ont panel LEDs LAN indicators Wireless Gateway’ s Front Panel LEDs WLAN Green . The Wireless LAN (WLAN) LED lights green when there is wireless activity . Link Green . The Link LED lights when the wireless option is enabled.
wireless gateway 10 setting up a wireless network network topology A wireless Local Area Network (LAN) uses a wireless adapter to connect each computer to the network. Computers in a wireless network must be configured to share the same radio channel.
11 gateway system tray application over view The Gateway installation wizard installed an application on your computer that functions as a tool kit for your Gateway . The application is accessed from a green, red, or yellow house icon in the Windows System T ray .
wireless gateway 12 ❑ Y ellow: connection to Gateway lost This computer is no longer connected to the home network or to the Internet. Besides providing constant feedback through the icon color , th.
status notification windows 13 status notification windows Any change in network status generates a status notification window describing the change and, if needed, suggests actions to take. The change may also cause a color change in the System T ray icon.
wireless gateway 14 This window appears when the Gateway attempts to access the Internet and cannot detect a connection. This window appears when your computer cannot establish a link to the Gateway .
status notification windows 15 This window appears when the Internet connection is restored. It also appears when when you first start your computer . Internet Connection Operational.
wireless gateway 16 pop-up menu Right-clicking the Gateway System T ray icon to display the following pop-up menu: This menu provides convenient access to Gateway tools, which are described in this section. Accessing a menu choice: 1 Right-click the icon, move cursor to highlight the desired option.
pop-up menu 17 Check for upgrade When a software or firmware upgrade becomes available on the HP W eb site, you are notified automatically by a notification window (assuming you have enabled this option — see “Notify me when network events occur” on page 27) and prompted to download and install the upgrade.
wireless gateway 18 Internet speed meter Selecting Internet speed meter ... launches a utility that monitors your upstream and downstream Internet connection speed.
pop-up menu 19 upstream speed (the speed at which data is uploaded from your computer to the Internet), as shown in the example. Contact your DSL or broadband cable provider for specifications. Gateway contro l panel The Gateway Control Panel allows you to adjust the settings of your Gateway .
wireless gateway 20 Save the current Gateway configuration This option provides a backup copy of your current Gateway settings in the event that you need to restore them. This is especially useful if you modify your settings using the Gateway Control Panel, upgrade Gateway software or firmware, or experience a system crash.
pop-up menu 21 2 Click Br owse to select a location to store the Gateway configuration backup file. The following dialog box appears: 3 Navigate to a location of your choice for the backup file, or accept the default.
wireless gateway 22 Restore a previous Gateway configuration Select this choice to restore a previously saved configuration. If you have saved more than one configuration, you can select a specific one. Internet connection diagnostic Restore a previous Gateway configuration.
pop-up menu 23 This utility checks your Internet connection to identify problems when a loss of connection occurs. Select the Internet connection diagnostic... to display the Internet connection diagnostic star t window: The utility checks for Internet connections via the Gateway or directly from your computer .
wireless gateway 24 Click Start to begin the diagnostic routine. The Internet Connection Diagnostic screen appears: Internet connection diagnostic report window.
pop-up menu 25 If all results are “ok”, the utility has not detected any connection problems. Interpreting a “failed” report for any parameter: ❑ Connection to the Gateway . “Failed” means you should per form a soft reset of your Gateway .
wireless gateway 26 Get current network status Selecting this choice generates one of the status notification windows discussed and illustrated in the section “status notification windows” on page 13. If all is well and the diagnostic utility detects no changes, the window appears: Get current network status.
pop-up menu 27 Notify me when network events occur Selecting this option displays the status notification windows discussed in “status notification windows” on page 13.
wireless gateway 28.
29 gateway contr ol panel over view The Gateway Control Panel allows you to configure additional functions beyond those installed through the Installation Wizard. This tool is a simplified alternative to the Expert Inter face, which is described in the Appendix of this user’ s guide .
wireless gateway 30 accessing the gateway contr ol panel The Gateway Control Panel is accessed from the Gateway System T ray icon described in the previous chapter . It can also be accessed from Start > Programs > HP Digital Home Networking > Gateway Contr ol Panel .
accessing the gateway control panel 31 3 Select Gateway control panel... The Gateway Control Panel Login window appears: 4 Enter your Gateway Password in the Login Password field, then click OK . The default password is “admin”. Select Gateway control panel.
wireless gateway 32 5 Click Hint on the Login screen if you cannot remember your password. The Password Hint window appears: 6 The question you provided when the default password was changed is displayed. Enter the answer in the Hint Answer field, then click OK .
gateway control panel screen 33 gateway contr ol panel screen When you have successfully logged on, the Gateway Control Panel screen appears with the My Network tab selected. With any tab selected, you can access all the other functions by clicking another tab.
wireless gateway 34 gateway contr ol panel tabs My Network tab This tab is a display-only over view of your network. It shows your Gateway and all the devices connected to the network, and it shows whether each device has an Ethernet, phoneline, or wireless connection.
gateway control panel tabs 35 Internet Access tab The Internet Access tab allows you to restrict specified computers on your network from accessing the Internet. Y ou can also allow one user to be exposed to the Internet for a special purpose such as Internet gaming or video conferencing (the firewall is disabled for that one user).
wireless gateway 36 3 Click and drag all selected computers to the Internet Access Disabled window or click the left-pointing arrow button between the two windows. 4 Click Apply to save the changes. Application Hosting tab The Application Hosting tab allows you to host Internet ser vices, e-mail, or an F TP ser ver on one network computer .
gateway control panel tabs 37 4 Enter the port number for the application; if a range is specified, click the Enter Port Range checkbox and enter the range of por t numbers in the Starting Por t and Ending Port fields.
wireless gateway 38 The index will help you locate additional information related to the operation of the Gateway Control Panel. Remote Support tab The Remote Support tab provides access to the HP Cus.
39 frequently asked questions (F AQs) gateway general information What is Network Address T ranslation and what is it used for? Network Address T ranslation (NA T) translates multiple IP addresses on the private LAN to one public address that is sent out to the Internet.
wireless gateway 40 page of the Expert Inter face. How can I block corrupted F TP downloads? If you are experiencing corrupted files when you download a file with your F TP client, tr y using another F TP program. What is DMZ Hosting? Demilitarized zone (DMZ) hosting allows one IP address (or computer) to be exposed to the Internet.
wireless networking information 41 wireless networking information Can I run an application from a remote computer over the wireless network? This depends on whether the application is designed to be used over a network.
wireless gateway 42 installation and configuration options How many IP addresses can the Gateway support? The Gateway supports a maximum of 253 IP addresses. Where is the Gateway installed on the network? In a typical environment, the Gateway is installed between the modem and the LAN.
installation and configuration options 43 What is the maximum number of virtual private network (VPN) sessions allowed by the Gateway? One VPN session at a time; the memor y buffer on the Gateway is 512 KB. My W eb pages hang up, I get corrupted downloads, or junk characters are being displayed on the screen.
wireless gateway 44 suppor ted software Does the Gateway support ICQ send files? Y es, with the following fix: from ICQ menu > preference > connections tab >, select I am behind a firewall or pr oxy and set the firewall time-out to 80 seconds in the firewall setting.
supported software 45 Does the Gateway support IPsec? A new IPsec pass-through feature is now included..
wireless gateway 46 suppor ted features What are the advanced features of the Gateway? The Gateway's advanced features include IP filtering, IP for warding, dynamic routing, static routing, DMZ hosting, and MAC address cloning.
upgrade information 47 upgrade information How will I be notified of new Gateway firmware upgrades? All Hewlett-Packard firmware upgrades are posted on the HP website at www .hp.com, where they can downloaded for free. The Gateway's firmware can be upgraded with T rivial File T ransfer Protocol (TF TP) programs.
wireless gateway 48.
49 tr oubleshooting I can’t connect to the Gateway . ❑ V erify that the Gateway is properly installed, the LAN connections are OK (the LAN LEDs should be lit), and it is powered on. ❑ V erify that the PC is using an IP address between 192.168.1.
wireless gateway 50 I can’t obtain an IP address from my cable or DSL modem. ❑ V erify that all of your cabling is properly connected and that the Gateway’ s W AN and LAN LEDs are lighting up. ❑ Power down your cable or DSL modem for a few seconds, then turn it back on.
51 appendix: the exper t inter face advanced administration For your convenience, a W eb-based administrative utility called the Expert Inter face has been programmed into your Gateway . Advanced Gateway administrative tasks may be perfor med through this interface.
wireless gateway 52 screens and functions The following pages contain descriptions of each screen and its functions. The screens described are: ❑ Setup ❑ Password ❑ Status ❑ DHCP ❑ Log ❑ H.
setup 53 setup The SETUP screen appears when the Expert Inter face is accessed. SETUP Screen.
wireless gateway 54 ❑ Host Name: Allows you to create a name for the Gateway , required by some Internet Ser vice Providers (ISPs). ❑ Domain Name: Allows you to create a domain name, required by some ISPs. ❑ Firmware V ersion: Shows the version of the firmware you are using.
setup 55 ❑ Login PPPoE: Check with your ISP to determine whether Point-to-Point Protocol over Ethernet (PPPoE) should be enabled. If PPPoE should be enabled: 1 Select PPPoE as the login method. 2 Enter the User Name and the Password as specified by your ISP .
wireless gateway 56 setting WEP encr yption Wired Equivalent Privacy (WEP) encryption is a method of encr ypting data transmitted over a wireless network to insure data security . In a wired network, data security is maintained through the physical wire.
setting WEP encr yption 57 4 Click WEP Key Setting ; the W eb T able appears. 5 Y ou may create a new WEP encr yption key by either generating a passphrase or manually entering a key . The passphrase method is recommended, but you may need to create a manual key to meet the requirements of existing wireless equipment on your network.
wireless gateway 58 2 Click Apply . Commit the passphrase or manual key to memor y since you will probably need it for other wireless devices on the network.
password 59 password The default password on your Gateway is “admin”. T o ensure security , we strongly recommend that you change your password when setting up your gateway , and then at regular inter vals. T o change your password: 1 Click the Password tab of the Expert Inter face to view the Password screen.
wireless gateway 60 T o enable remote management: 1 Click the Advanced tab. 2 Click the Filters tab and select Enable under Remote Management. 3 Click Apply . A remote managment password will be assigned. T o change remote management password: 1 On the Password screen, in the Remote Management Password box, enter a new password.
status 61 status The ST A TUS screen displays the current status of the Gateway , reflecting data and selections entered on the SETUP screen. All of the information provided on the ST A TUS screen is read-only . T o make changes, select the Setup tab.
wireless gateway 62 ❑ Host Name: Shows the name of your Gateway , which is required by some ISPs. ❑ Firmware V ersion: Shows the version and date of the installed fir mware. Dates are slightly more accurate than version numbers. ❑ Login: Shows whether PPPoE or RAS support is enabled and whether either one is connected.
DHCP 63 DHCP A Dynamic Host Configuration Protocol (DHCP) ser ver automatically assigns IP addresses to each computer on a network. Unless you already have a DHCP ser ver on your network, it is highly recommended that your Gateway be set up as a DHCP ser ver .
wireless gateway 64 Gateway is 192.168.1.1, the starting IP address must be 192.168.1.2 or greater . ❑ Number of DHCP users: Enter the maximum number of devices to which you want the DHCP ser ver to assign IP addresses. Accept the default value or you may enter a number up to a maximum of 253.
log 65 log The LOG screen displays a record of all access traffic passing through the Gateway , including e-mail and F TP tranmissions, whether they originate from your LAN, your W AN, or from the Internet. Check logs through the LOG screen or by using the LogViewer W indows application.
wireless gateway 66 help The HELP screen links to all of the Expert Inter face online help screens. Each help screen, as well as all of the settings screens, contain links to the HP W eb site (including technical support and Customer Care). Select the Help tab of the Exper t Interface to view the HELP screen.
advanced 67 advanced The Advanced screen provides access to six settings screens: Filters, For warding, Dynamic Routing, Static Routing, DMZ Host, and Mac Clone.
wireless gateway 68 Select the Filters tab of the Exper t Interface to view the FIL TERS screen. ❑ Filtered Private IP Range: Enter the range of IP addresses desired to filter into the IP address range fields. Users with these IP addresses will not be able to access the Internet.
advanced 69 in both boxes. For example, if the IP address is 192.168.1.5, enter 5 in each box. ❑ Filtered Private Por t Range: Filter users by entering their network por t numbers. Select the protocols and enter the range of port numbers that you want to filter into the port number range fields.
wireless gateway 70 forw arding Select the Forwarding tab of the Exper t Interface to view the FORW ARDING screen. port for warding Port for warding is used to set up public ser vices on a network, such as W eb, F TP , or e-mail ser vers.
advanced 71 example, if you set port number 80 (HTTP) to be for warded to IP address 192.168.1.2, then all HTTP requests from outside users will be for warded to 192.168.1.2. Enter a valid IP address. Y ou may need to establish a static IP address with your Internet provider in order to properly run an Internet ser ver .
wireless gateway 72 dynamic routing Dynamic routing allows the Gateway to automatically adjust to physical changes in network layout. The Gateway , using the dynamic Routing Infor mation Protocol (RIP) protocol, determines the route that the network packets take based on the fewest number of hops between source and destination.
advanced 73 network with other routers, including a separate network gateway that handles the Internet connection. 2 In the TX field, choose the protocol to transmit data on the network. 3 In the RX field, choose the protocol to receive data from the network.
wireless gateway 74 Select the Static Routes tab of the Exper t Interface to view the ST A TIC ROUTING screen. T o view current routing table: Click Show Routing T able to see all valid static route entries in use. T o create a static route entr y: 1 Select a static route entr y from the Static Routing drop-down list.
advanced 75 ❑ Destination LAN IP: Enter the IP address of the remote network or host for which you wish to create a static route. If you are building a route to an entire network set the network portion of the IP address to zero (0). For example, the Gateway’ s standard IP address is 192.
wireless gateway 76 DMZ host The DMZ Host setting screen allows one local user to be exposed to the Internet for a special purpose such as Internet gaming or video conferencing. Whereas IP For warding can only for ward a maximum of ten ranges of por ts, DMZ hosting for wards all the por ts for one PC simultaneously .
advanced 77 MAC address clone A Media Access Control (MAC) address is a unique 12-digit identification code assigned to a hardware device. MAC address clone attaches the MAC address of the network card/adapter onto your Gateway that was connected to your cable or DSL modem during installation.
wireless gateway 78 5 Enter the 12-digit MAC address, found in the Adapter/Physical Address field, in the User Defined W AN MAC Address boxes on the MAC Address Clone screen.
79 specifications general Model number hn200w Standards IEEE 802.3 (10BaseT), IEEE 802.3u (100BaseTX), IEEE 802.11b (wireless) Protocol CSMA/CD Ports LAN: four 10/100 RJ-45 switched ports, one shared .
wireless gateway 80 envir onmental Dimensions 189.2 mm x 150.9 mm x 53.1 mm (7.45” x 5.94” x 2.09”) Power input External, 5V DC, 2.5 amp Certifications FCC Part 15 Classes B and C Operating temp.
81 glossar y 10BaseT Ethernet standard topology for twisted pair (T) cabling (transfer rate of 10 Mbps over 100 meters). 100BaseT Fast Ethernet twisted pair cabling (transfer rate of 100 Mbps over 100 meters).
wireless gateway 82 client/server network Network in which one computer (the “ser ver”) shares resources with other computers, called “clients” (as opposed to a peer-to-peer network).
glossar y 83 DNS (Domain Name System) Method for matching Internet domain names with IP addresses. When a Uniform Resource Locator (URL) is entered into a W eb browser , a domain name ser ver retrieves the corresponding IP address for the domain name specified (“name resolution”) and sends the request to the appropriate ser ver .
wireless gateway 84 FHSS (Frequency Hopping Spread Spectrum) Uses a narrowband carrier that changes frequency in a pattern known to both transmitter and receiver . Properly synchronized, the net effect is to maintain a single logical channel. T o an unintended receiver , FHSS appears to be shor t- duration impulse noise.
glossar y 85 Internet W orldwide network of networks linking millions of computers together; see also W AN (Wide Area Network). intranet Private home or business network. IP (Internet Protocol) address A unique 12-digit number (for example, 205.112.134.
wireless gateway 86 network System connecting two or more computers and peripherals enabling them to communicate and share resources. network adapter See NIC (Network Interface Card). network mask See subnet mask. NIC (Network Interface Card) Card or adapter that allows a computer to connect to a network.
glossar y 87 PPTP (Point-to-Point T unneling Protocol) Protocol allowing corporations to extend their corporate network over the Internet through private “tunnels.” This has the effect of using the Internet as a large private local area network known as a “virtual private network” or VPN.
wireless gateway 88 server Computer on a network that provides ser vices to other computers on the network. SPI (stateful packet inspection) The ability of a firewall to remember outgoing requests to .
glossar y 89 TCP/IP (T ransmission Control Protocol/Internet Pr otocol) Basic communication language of the Internet (but can also be used in private networks). TCP keeps track of individual data packets, while IP handles the actual deliver y of the data.
wireless gateway 90.
91 index A administration quick and easy 51 antenna jack 7 D DHCP explained 63 setting up 63 DMZ host 76 dynamic routing 72 E encr yption WEP 56 Expert Inter face setting WEP encr yption 56 expert int.
wireless gateway 92 WLAN LED 9.
93 regulator y notices hewlett-packard company This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: ❑ This device may not cause harmful inter ference, and ❑ This device must accept any interference received, including inter ference that may cause undesired operation.
wireless gateway 94.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté HP hn200w c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du HP hn200w - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation HP hn200w, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le HP hn200w va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le HP hn200w, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du HP hn200w.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le HP hn200w. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei HP hn200w ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
