Manuel d'utilisation / d'entretien du produit C160L du fabricant HP (Hewlett-Packard)
Aller à la page of 280
Service Handbook C Class Models C100, C1 10, C160L, C160, C180, C200 and C240 HP Part No. A4200-90041 Edition E0897 Printed in U.S.A..
ii Hewlett-Packard Co. 1997 Printing History First Printing: August 1997 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Lim- ited. NOTICE The information contained in this document is subject to change without notice.
Safety and Regulatory Statements iii Safety and Regulatory Statements This section contains safety and regulatory statements pertaining to the C100, C1 10, C160L, C160, C180, C200 and C240 workstations.
Special Video Configuration Statements iv Special Video Configuration Statements The following statements apply only to those applica- tions which include a cable connected to the S-V ideo connector on the A4248A card.
Models C160L/C160/C180/C200/C240 Emissions Regulations v Models C160L/C160/C180/C200/C240 Emissions Regulations Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and the Canadian Depart- ment of Communications.
Models C160L/C160/C180/C200/C240 Emissions Regulations vi computer . Changes or modifications not expressly approved by Hewlett-Packard could void the user ’ s authority to operate the equipment. Operation of this device is subject to the following conditions: • This device may not cause harmful interference.
Models C100/C1 10 Emissions Regulations vii Models C100/C110 Emissions Regulations Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules and the Canadian Depart- ment of Communications.
Models C100/C1 10 Emissions Regulations viii computer . Changes or modifications not expressly approved by Hewlett-Packard could void the user ’ s authority to operate the equipment. Operation of this device is subject to the following conditions: • This device may not cause harmful interference.
Emissions Regulations Compliance ix Emissions Regulations Compliance Any third-party I/O device installed in HP system(s) must be in accordance with the requirements set forth in the preceding Emissions Regulations statements.
Electrostatic Discharge (ESD) Precautions x Electrostatic Discharge (ESD) Precautions Electrostatic charges can damage the integrated cir- cuits on printed circuit boards. T o prevent such dam- age from occurring, observe the following precautions during board unpacking and installation: • Stand on a static-free mat.
Laser Safety Statement (U.S.A. Only) xi Laser Safety Statement (U.S.A. Only) The CD ROM mass-storage system is certified as a Class-1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Per- formance Standard according to the Radiation Control for Health and Safety Act of 1968.
W arnings and Cautions xii Warnings and Cautions.
Contents xiii 1 Product Information Product Description 3 System Unit Front Panel Controls 6 System Power Switch 6 Power LED 7 System LEDs 7 Audio Controls 8 Storage Device Controls and Features 8 CD-.
Contents xiv Operating System Overview 28 2 Environmental/Installation/PM Environmental Specifications 31 Installation 33 Preventive Maintenance 33 3 Configuration W orkstation Configurations 37 FR.
Contents xv Graphics Configuration Restrictions 60 4 T roubleshooting Getting Ready to T roubleshoot 63 Dealing with a Boot Failure 68 Searching for Bootable Media 70 Stable Storage 71 Boot Command N.
Contents xvi Storage Devices 121 Human Interface Board 123 Main T ray Assembly 124 Removing Memory Modules 125 Installing Memory Modules 127 Removing Second Level Cache Modules (C160L) 129 Installing .
Contents xvii Service Manuals 171 Reference Manuals 171 8 Service Notes 9 Boot Console Interface Model C100/1 10 Accessing the Boot Console Interface 179 Boot Console Menus 181 Searching for Bootable .
Contents xviii Displaying the LAN Station Address 204 Displaying System Information 205 Displaying PIM Information 206 Configure and Display LAN Settings 207 Stable Storage 209 ISL Environment 210 In.
Contents xix Changing the Console to External T erminal 235 Displaying the Status of the System I/O 236 Setting the Auto Boot and Auto Search Flags 237 Displaying and Setting the Fastboot Mode 239 Dis.
Contents xx Figures System Unit Front Panel Controls 6 CD-ROM Drive Controls and Features 9 DDS-DC Drive Controls and Indicators 1 1 DDS-2 Drive Controls and Indicators 1 1 Floppy Drive Controls and F.
Contents xxi Figures DDS Drive Switch Settings for Data Compression Oper- ation Mode 49 Memory Connectors (Model C100/1 10) 51 Memory Connectors (Model C160L) 51 Memory Connectors Model (C160/180XP/20.
Contents xxii Figures Removing a Storage Device 122 Removing the Human Interface Board 123 Removing the Main T ray Assembly 124 Memory Module Location (C100, C1 10) 125 Memory Module Location (C160L) .
Contents xxiii Figures Removing the CPU Area Fan Assembly 143 Removing the Fan 144 Removing the Rear Panel 145 Removing the I/O Board 148 Removing the I/O Extension Board 149 Removing the Battery 150 .
Contents xxiv T ables CD-ROM Drive Controls and Features 9 DDS T ape Drive Controls and Features 12 Floppy Drive Controls and Features 13 Audio Electrical Specifications 18 Serial I/O Pins 20 PS/2 Ke.
Contents xxv T ables Fan Power Pinouts 162 LED Power Pinouts 162 System Paths 187 Mnemonic Style Notation for Boot Paths 188 Graphics Configurations and Hardware Slots 191 System Paths 225 Mnemonic S.
Contents xxvi T ables.
1 1 Product Information.
Product Information 2 This chapter introduces the HP 9000 C Class worksta- tions, including their controls and indicators. This chapter discusses the following topics: • Product description • Syst.
Product Information Product Description 3 Product Description The C Class workstations contain the following key features: • Processor Performance: 100 MHz (Model C100) 120 MHz (Model C110) 160 MHz (Model C160L) 160 MHz (Model C160) 180 MHz (Model C180XP) 200 MHz (Model C200) 236 MHz (Model C240) • Operating System: Native HP/UX HP-UX 9.
Product Information Product Description 4 • Memory 32 MB to 512 MB Main Memory in pairs of 16 MB, 32MB, or 64 MB modules - four pairs maximum (C100/110/160L) 32 MB to 768 MB Main Memory in pairs of 16 MB, 32MB, or 64 MB modules - six pairs maximum (C160/180) 32 MB to 1.
Product Information Product Description 5 connector (C200 new only) Two Serial Interfaces RS232C, 9-pin male One Parallel Interface, Centronics, BUSY hand- shake, 25-pin female 16 Bit Audio Line-in an.
Product Information System Unit Front Panel Controls 6 System Unit Front Panel Controls Figure 1 shows the location of the system unit front panel controls. Figure 1 System Unit Front Panel Controls System Power Switch Use the Power switch to power the system unit on and off.
Product Information System Unit Front Panel Controls 7 NOTICE: There is no need to manually shut down the HP- UX operating system on your workstation before powering it off. When you turn of f the power switch, your workstation automatically shuts down the operating system before terminating the power .
Product Information System Unit Front Panel Controls 8 Audio Controls Next to the system LEDs are the following audio con- trols: The volume control, headset jack, and microphone jack features of the CD-ROM are supported through applications only .
Product Information System Unit Front Panel Controls 9 CD-ROM Drive Figure 2 shows the operating controls and features of the CD-ROM drive, and T able 1 describes them.
Product Information System Unit Front Panel Controls 10 Eject Button Press to open the disc tray and insert or remove a disc. When the drive is in use, press the eject button for more than one second to open the disc tray . Emergency Eject Insert the end of a paper clip to open the disc tray when the workstation does not have power .
Product Information System Unit Front Panel Controls 11 DDS T ape Drive Y our DDS tape drive is either a DDS-DC or DDS-2 tape drive with a 3.5-inch form factor , data compres- sion, and a single-ended SCSI interface. Both drives incorporate data compression capability and are high- capacity , high transfer-rate devices for data storage on tape.
Product Information System Unit Front Panel Controls 12 T able 2 DDS T ape Drive Controls and Features Control/Featur e Purpose Eject Button Push the eject button to remove tape cassettes from the drive. Drive LEDs The DDS drive LEDs light and flash to indicate drive status and error conditions.
Product Information System Unit Front Panel Controls 13 Floppy Disk Drive Figure 5 shows the operating controls and features of the floppy drive, and T able 2 describes them.
Product Information System Unit Rear Panel Connectors 14 System Unit Rear Panel Connectors This section describes the following connectors on the system unit’ s rear panel: • Security loop • Audio connectors • Keyboard and mouse connectors • HP parallel (Centronics) I/O connector • 802.
Product Information System Unit Rear Panel Connectors 15 Figure 6 System Unit Rear Panel Connectors Security Loop The security loop provides a means of locking the storage tray with a padlock or other locking device, to prevent unauthorized removal from the system.
Product Information System Unit Rear Panel Connectors 16 Audio Connectors The C Class workstations have audio input and output capability through external input and output connec- tors on the rear panel and through an internal speaker . The rear panel contains the Line IN (Stereo line-in) and Line OUT (Stereo line-out) connectors.
Product Information System Unit Rear Panel Connectors 17 • Audio Outputs Line-out Headset Built-in mono speaker • Audio CODEC Crystal CS4215.
Product Information System Unit Rear Panel Connectors 18 T able 4 summarizes the audio electrical specifications for the C Class workstations. T able 4 Audio Electrical Specifications Frequency Response 25-20,000Hz Input Sensitivity/Impedance Line Out 2.
Product Information System Unit Rear Panel Connectors 19 Keyboard and Mouse Connectors PS/2 Keyboard and Mouse Connectors The PS/2 connectors provide an interface for the key- board, mouse, and a variety of other pointing devices, such as trackballs, to the system.
Product Information System Unit Rear Panel Connectors 20 Serial Input/Output Connectors There are a variety of pointing devices (mouse or trackball) or peripheral devices that can attach to the Serial Input/Output (SIO) ports on the workstation. Peripheral devices include printers, plotters, modems, and scanners.
Product Information System Unit Rear Panel Connectors 21 SCSI Connectors Use the SCSI connectors to connect external SCSI devices such as DDS-format tape drives and CD-ROM drives. Consult the documentation that accompanies each SCSI device for specific information concerning its use.
Product Information Monitors 22 Monitors The Models C100/C1 10/C200 do not have a built-in graphics controller . A graphics board is installed in on of the option slots. The Models C160L, C160, and C180 have a graphics controller built-in on the I/O board.
Product Information Keyboards 23 Keyboards There are two types of Hewlett-Packard keyboards available: • PS/2 Keyboard (PS/2 interface) (All C Class Workstations) • ITF Keyboard (HP-HIL interface).
Product Information Keyboards 24 Some applications expect to use keycodes generated by keys existing on the ITF keyboard. Since the keys do not exist on the PS/2 keyboard, an accommodation must be made if the PS/2 keyboard is to be used.
Product Information Keyboards 25 Alt (right) Extend Char (right) No Equivalent Clear Line No Equivalent Clear Display No Equivalent Insert Line No Equivalent Delete Line No Equivalent Print/Enter No E.
Product Information Keyboards 26 6/ (number pad) 6 (number pad) 7/Home (number pad) 7 (number pad) 8/ (number pad) 8 (number pad) 9/Pg Up (number pad) 9 (number pad) .
Product Information Pointing Devices 27 Pointing Devices The PS/2 connector , the HIL port, or the Serial ports support using an HP three-button mouse, a trackball, or other options as pointing devices. For instructions on using a particular device, see the manual that came with that device.
Product Information Operating System Overview 28 Operating System Overview The C Class workstations use the HP-UX operating system. The individual models require the following minimum versions: Model C100/1 10 - HP-UX 9.05 or later Model C160L - HP-UX 10.
29 2 Environmental/Installation/ PM.
Environmental/Installation/PM 30 This chapter lists the environmental specifications and regulatory requirements for the system. Installation and preventive maintenance information, if applicable, is also provided.
Environmental/Installation/PM Environmental Specifications 31 Environmental Specifications T able 7 lists the environmental specifications for the C Class workstations.
Environmental/Installation/PM Environmental Specifications 32 V ibration Operating random 0.21 G rms, 5-50 Hz Swept sine survival 0.5 G peak, 5-500 Hz Random survival 2.
Environmental/Installation/PM Installation 33 Installation Refer to Har dwar e Installation Car d C Class ( Part Number A4200-90012) for system installation infor- mation. Preventive Maintenance The system unit requires no preventive maintenance. Some removable media storage devices require opera- tor preventive maintenance.
Environmental/Installation/PM Preventive Maintenance 34.
35 3 Configuration.
Configuration 36 This chapter provides details about setting up and changing the system configuration..
Configuration Workstation Configurations 37 Workstation Configurations Refer to the HP 9000 C Class Configuration Guide for a complete list of supported accessories, peripherals, and operating systems for your workstation.
Configuration FRU Configurations 38 FRU Configurations This section provides information for setting up or changing the configuration of the system Field Replaceable Units (FRUs). Internal Storage Configurations Each storage device is restricted as to where in the storage tray it may be installed.
Configuration FRU Configurations 39 T able 9 lists the recommended SCSI IDs for internal storage devices. Figure 8, Figure 9, and Figure 10 show the FWD SCSI and UWSE SCSI ID settings for the hard disk drives. Figure 1 1 and Figure 14 show the Narrow Single-Ended SCSI ID settings for the CD- ROM drive and the DDS drive.
Configuration FRU Configurations 40 NOTICE: The floppy disk drive is not a SCSI device. T able 9 Default SCSI IDs Fast, Wide Differ ential SCSI 1st Hard Disk Drive ID 6 2nd Hard Disk Drive ID 5 3rd.
Configuration FRU Configurations 41 Figure 8 Hewlett-Packard 2 GB Fast, Wide Differential Disk Drive Jumper Settings (1-inch Low Profile) SCSI ID 6 5 4 3 2 1 0 SCSI ID 15 14 13 12 11 10 9 8.
Configuration FRU Configurations 42 Figure 9 Seagate 2 GB FWD or UWSE Disk Drive Jumper Settings (1-inch Low Profile) SCSI ID Jumpers SCSI ID 6 5 4 3 2 1 0 SCSI ID 15 14 13 12 11 10 9 8.
Configuration FRU Configurations 43 Figure 10 Seagate 4 GB, FWD or UWSE Disk Drive Jumper Settings (1.6-inch Full Height) SCSI ID SCSI ID 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 SCSI ID Jumpers.
Configuration FRU Configurations 44 Figure 11 Early Model CD-ROM Drive SCSI Address/Jumper Settings SCSI ID 0 1 2 3 SCSI ID 4 5 6 SCSI Jumpers.
Configuration FRU Configurations 45 Figure 12 Later Model CD-ROM Drive SCSI Address/Jumper Settings.
Configuration FRU Configurations 46 Figure 13 Early Model DDS-DC Tape Drive SCSI Address/Jumper Settings SCSI ID 0 1 2 3 SCSI ID 4 5 6.
Configuration FRU Configurations 47 Figure 14 Later Model DDS-DC Tape Drive SCSI Address/Jumper Settings.
Configuration FRU Configurations 48 Figure 15 DDS-2 Tape Drive SCSI Address/Jumper Settings.
Configuration FRU Configurations 49 Figure 16 DDS Drive Switch Settings for Data Compression Operation Mode.
Configuration FRU Configurations 50 Allowable Memory Configurations The Model C100/1 10/160L workstations have 8 mem- ory slots, labeled 0A, 0B through 3A, 3B. The mem- ory configuration is 32 MB to 512 MB installed in pairs of 16 MB, 32 MB, or 64 MB memory modules.
Configuration FRU Configurations 51 Figure 17 Memory Connectors (Model C100/110) Figure 18 Memory Connectors (Model C160L) 0A 2A 0B 2B 1A 3A 1B 3B 0A 2A 0B 2B 1A 3A 1B 3B.
Configuration FRU Configurations 52 Figure 19 Memory Connectors Model (C160/180XP/200/240) See chapter 5 of this manual for details on installing memory modules.
Configuration FRU Configurations 53 Monitor-Type Selection The built-in graphics in the C Class workstations sup- port the following two monitors: • 17-inch, 1280x1024 color monitor (A4032A) • 2.
Configuration Graphics Configurations 54 Graphics Configurations This section describes the rules for installing and con- figuring graphics options in your C Class workstation.
Configuration Graphics Configurations 55 Models C100 and C110 graphics0 through graphics2 are not supported . If the configuration value is set to “ default ” (graphics 0) , the system console will be graphics 3, Slot 3 . graphics3 Graphics device in slot3.
Configuration Graphics Configurations 56 Models C160 and C180 This subsection describes the graphics configuration rules and restrictions for the Models C160 and C180. Note that a C200 upgraded from a C160/C180 will have these same rules and restrictions.
Configuration Graphics Configurations 57 Graphics Configuration Restrictions This subsection describes restrictions on the installa- tion and support of graphics adapters. Graphics Displays The system supports only four graphics displays at a time. A “display” is a video out- put port or connector .
Configuration Graphics Configurations 58 remaining odd numbered slot. If the highest numbered slot used by the V isualize 48Z board set is an odd numbered slot, then you may only install a graphics card in the remaining even numbered slot.
Configuration Graphics Configurations 59 Models C160L This subsection describes the graphics configuration rules and restrictions for the Models C160L. Graphics Paths graphics(0) is the built-in 8-plane graphics adapter . graphics(1) and graphics(2) are graphics adapters installed in option slots 1 and 2.
Configuration Graphics Configurations 60 Graphics Configuration Restrictions The system supports only four graphics displays at a time. A “display” is a video output port or connector . For example, the Dual V isualize Enhanced Graphics Card (A4451A) is a dual display card.
61 4 Troubleshooting.
T roubleshooting 62 This chapter provides information about isolating a failing component, known as a Field Replaceable Unit (FRU), in the C Class workstations.
T roubleshooting Getting Ready to T roubleshoot 63 Getting Ready to Troubleshoot T o troubleshoot a C Class workstation, you must be familiar with the HP-UX operating system and be able to start and stop processes.
T roubleshooting Getting Ready to T roubleshoot 64 Figure 20 Power On Troubleshooting.
T roubleshooting Getting Ready to T roubleshoot 65 Figure 21 Selftests Troubleshooting.
T roubleshooting Getting Ready to T roubleshoot 66 Figure 22 HP-UX Compatible Mode Troubleshooting.
T roubleshooting Getting Ready to T roubleshoot 67 Figure 23 HP-UX Compatible Mode Troubleshooting (Continued).
T roubleshooting Dealing with a Boot Failure 68 Dealing with a Boot Failure T o start the workstation from an operating system stored on a device different from the usual boot device, to boot from a d.
T roubleshooting Dealing with a Boot Failure 69 boot sescsi.1.0 (C160L, C160, and C180) boot scsi.1.0 (C100 and C110) The operating system on the specified device is used to start the workstation.
T roubleshooting Dealing with a Boot Failure 70 Searching for Bootable Media T o list all devices that may contain bootable media, go to the Main Menu of the Boot Console Interface and then type the following at the prompt: search ipl The search may turn up more devices than there are lines on the display .
T roubleshooting Dealing with a Boot Failure 71 Stable Storage Stable Storage is non-volatile memory associated with each P A-RISC processor module. Stable storage is used by the processor (CPU) to store device path information, the state of the boot flags, HPMC error information, and operating system initialization data.
T roubleshooting Dealing with a Boot Failure 72 Supported Boot Paths SCSI devices are bootable when connected to the NSE SCSI and FWD or UWSE SCSI ports on the System card.
T roubleshooting Selftest Failures 73 Selftest Failures Chassis codes are the key to debugging selftest errors. If a failure is found during selftest, chassis codes are displayed in the diagnostic LEDs.
T roubleshooting Selftest Failures 74 In the following tables, shaded LEDs indicate that they are lit. T able 12 LED Error Codes (C100/1 10) LED V alue RS-232 Chassis Code Range Description N/A Reserv.
T roubleshooting Selftest Failures 75 Any fault not in this table including 1000-1019 Unknown F AUL T CBF0 - CBFF HPMC F AUL T A000 - A0C0 No console/IPL error F AUL T N/A Reserved N/A Reserved N/A Po.
T roubleshooting Selftest Failures 76 T able 13 LED Error Codes (C160L/160/180) LED V alue RS-232 Chassis Code Range Description N/A Reserved 7401 No memory found F AUL T Likely cause: SIMMs or pr oce.
T roubleshooting Selftest Failures 77 Chassis Display Codes Below are definitions for all Raven-U/U+ chassis display codes. The codes are organized in approximate numerical order for ease of reference. These codes are displayed on the serial console, if enabled.
T roubleshooting Selftest Failures 78 chassis codes “8C0y”. They are preceded by “TEST “. Code Name Meaning 0001 DINO_IAR0_ONES_TEST srs iar0 register 0002 DINO_IAR0_ZERO_TEST srs iar0 registe.
T roubleshooting Selftest Failures 79 tion trap* 1x13 UNEXPECTED_INTERRUPT Data memory break trap* 1x14 UNEXPECTED_INTERRUPT TLB dirty bit trap* 1x15 UNEXPECTED_INTERRUPT Page Reference trap* 1x16 UNE.
T roubleshooting Selftest Failures 80 1zBA BOOT_ABDICATION Bad monarch CPU 1zBB BAD_CPU_NUMBER CPU Number not 0-3 1zBC BAD_CLOCKS Bad CPU clock speed detected 1zBD BAD_CPU_ORDER CPUs not installed in .
T roubleshooting Selftest Failures 81 2x12 ICACHE_ALINE_OPEN {FLT}, ICACHE_ALT_WRITE {TEST} FLT extended info D000/F000 D=data open, F=tag open Control Address[0:15] Control Address[16:31] Test Addres.
T roubleshooting Selftest Failures 82 2x30 ITAG Icache tag selftest 2x33 DCACHE_ALT_WRITE0 2x40 CACHE_IERR Icache parity error detection selftest 2x44 DCACHE_ALT_READ0 2x50 DCACHE_STORE_QUEUE Dcache s.
T roubleshooting Selftest Failures 83 2xB2 DCACHE_ODD_TAG_PARITY 2xB3 DCACHE_EVEN_DATA_PARITY 2xB4 DCACHE_ODD_DATA_PARITY 2xBB XTRA_ICACHE_RAM 2xC0 ICACHE_PARITY Icache parity error 2xC1 ICACHE_TAG_PA.
T roubleshooting Selftest Failures 84 4z0E EXITING_LST Exiting Late Selft- est 4z10 CACHE_PM_BYTE Starting PM cache byte selftest 4z20 LST_EST Early selftests dur- ing late selftests 4z21 LST_BASIC CP.
T roubleshooting Selftest Failures 85 70FF UNKNOWN_HPMC 7101 MMC_NOT_RESPONDING 7102 MMC_NOT_READY_ERROR 7103 MMC_FAILED_TO_CLEAR 7104 MMC_STICKY_BITS 7105 MMC_BAD_REV 7106 MMC_REG_ERROR 7107 MMC_ERR_.
T roubleshooting Selftest Failures 86 error 7D0A HPMC_BAD_ADDR Address did not map to bank 7F00 MEM_FRU_ID D3 = SIMM pair 7FFF CATASTROPHIC_MEM_ERR Code Name Meaning 802B IO_BUS_OVERLAP Most likely gr.
T roubleshooting Selftest Failures 87 kludge for labproto BP For the following section of PCI-related chassis codes: The “1” or “2” is the GSC bus number that the host is attached to.
T roubleshooting Selftest Failures 88 cause PDH poweron reset C10x MONARCH_SELECTION end of Monarch se- lection C200 RAM_CONFIG Starting memory con- figuration C201 BEG_DESTR_MEM_INIT Starting detruct.
T roubleshooting Selftest Failures 89 not 2K byte aligned C5F2 BAD_LIF_MAGIC_PRI LIF file not present on media C5F3 BAD_IPL_SIZE_PRI LIF file 0; not n*2K bytes; or >256K bytes C5F4 BAD_IPL_ENTRY_PR.
T roubleshooting Selftest Failures 90 CB0B BR_TO_OS_TOC Branching to OS_TOC handler CB0C OS_TOC_FAILED Branch to OS_TOC failed CB10 LPMC_INITIATED LPMC handling initi- ated CB15 ULPMC Runway LPMC erro.
T roubleshooting Selftest Failures 91 Code Name Meaning CD10 BUS1_DINO Dino GSC to PCI bus bridge on GSC bus 1 CD11 BUS1_SLOT1 Bluefish (or ATM or ??) card in GSC slot 1 CD12 BUS1_SLOT2 Bluefish (or A.
T roubleshooting Selftest Failures 92 CDEE EISA_CARD_INIT_ERROR (Expected in EISA- capable system only) CDEF NO_EISA_FOUND (Expected in EISA- capable system only) CDFF INIT_SYSTEM_MAP_TABLE Building the system map table CHRONOLOGICAL EXAMPLE C240+ Firmware Version 4.
T roubleshooting Selftest Failures 93 TEST 2071 CHASSIS_DCACHE_RAM TEST_NORMAL_PATTERNS_EVEN TEST 2072 CHASSIS_DCACHE_RAM TEST_INVERSE_PATTERNS_EVEN TEST 2073 CHASSIS_DCACHE_RAM TEST_NORMAL_PATTERNS_O.
T roubleshooting Selftest Failures 94 TEST 4022 CHASSIS_LST_ALU TEST 4023 CHASSIS_LST_BR TEST 4023 CHASSIS_LST_BR TEST 4024 CHASSIS_LST_ARITH_COND TEST 4024 CHASSIS_LST_ARITH_COND TEST 4025 CHASSIS_LS.
T roubleshooting Running System V erification T ests 95 Running System Verification Tests HP-UX uses an online diagnostics product called the Support T ools Manager that allows system operation verification.
T roubleshooting Running System V erification T ests 96 6 To verify the system operation, type the following at the CSTM> prompt: verify all Messages similar to the following appear: Verification has started on device (CPU). Verification has started on device (FPU).
T roubleshooting Running ODE-Based Diagnostics 97 Running ODE-Based Diagnostics The Offline Diagnostic Environment (ODE) consists of diagnostic modules for testing and verifying system operation. ODE provides all the necessary functions for the user to load specified tests and interact with those tests.
T roubleshooting Running ODE-Based Diagnostics 98 • mapper - identifies the configuration of HPPA systems. It displays path, identification, and revision information of I/O components, configuration.
T roubleshooting T roubleshooting the SCSI I/O Board 99 Troubleshooting the SCSI I/O Board The following flowcharts guide you through trouble- shooting the ultra, wide, single-ended SCSI core I/O board and the fast, wide, differential SCSI core I/O board.
T roubleshooting T roubleshooting the SCSI I/O Board 100 A4125-66521 UWSE Core I/O Board Boot system to BCH Execute IN IO Execute SEA FWSCSI The core I/O board is most likely the problem. Replace it and try the system again. If it still fails and you reach this point again, replace the backplane instead.
T roubleshooting T roubleshooting the SCSI I/O Board 101 A4125-66521 UWSE Core I/O Board Possible problems: 1. Duplicate SCSI ID’ s assigned. ID 7 is reserved for host adapter . 2. Incorrect cables used. Use only the UWSE 90 ohm cables, p/n C2978A and C2979A.
T roubleshooting T roubleshooting the SCSI I/O Board 102 A4125-66522 FWD Core I/O Board Boot system to BCH Execute IN IO Execute SEA FWSCSI The core I/O board is most likely the problem. Replace it and try the system again. If it still fails and you reach this point again, replace the backplane instead.
T roubleshooting T roubleshooting the SCSI I/O Board 103 A4125-66522 FWD Core I/O Board Possible problems: 1. Duplicate SCSI ID’ s assigned. ID 7 is reserved for host adapter . 2. Incorrect cables used. Use only the FWD 70 ohm cables. 3. Check cabling configuration, especially maximum allowed length.
T roubleshooting T roubleshooting the SCSI I/O Board 104.
105 5 Field Replaceable Units.
Field Replaceable Units 106 This chapter lists the C Class Field Replaceable Units (FRUs) and provides procedures and illustrations showing their removal and replacement. Use the following tools to remove or replace FRUs: • Light-duty flat blade screwdriver with 150-mm (6-in.
Field Replaceable Units Exchange and Nonexchange Part Numbers 107 Exchange and Nonexchange Part Numbers In this chapter we refer to exchange and nonexchange part numbers. Y ou must return FRUs with exchange part numbers in exchange for a replacement FRU.
Field Replaceable Units Exchange and Nonexchange Part Numbers 108 Figure 26 shows the Main T ray FRUs for the C Class workstations. The numbers correspond to item num- bers in T able 14 and T able 15.
Field Replaceable Units Exchange and Nonexchange Part Numbers 109 Figure 27 shows the Storage T ray FRUs for the C Class workstations. The numbers correspond to item numbers in T able 14 and T able 15.
Field Replaceable Units Exchange and Nonexchange Part Numbers 11 0 Figure 28 shows the Power Supply FRUs for the C Class workstations. The numbers correspond to item numbers in T able 14 and T able 15. Figure 28 Power Supply FRUs T able 14 lists the exchange parts, and T able 15 lists the nonexchange parts in the C Class workstations.
Field Replaceable Units Exchange and Nonexchange Part Numbers 111 T able 14 Exchange Parts FRU List Figure Number Part Number Description A6 A4200-66521 A4200-69022 A4125-69021 I/O Board (C100, C1 10).
Field Replaceable Units Exchange and Nonexchange Part Numbers 11 2 T able 15 Nonexchange Parts FRU List Figure Number Part Number Description A4200-62023 A4200-62059 Chassis (C100/1 10) Chassis (C160L.
Field Replaceable Units Exchange and Nonexchange Part Numbers 11 3 B3 A4200-61603 A4125-63001 FWD SCSI Cable UWSE SCSI Cable B4 A4200-61602 NSE SCSI Cable B5 A4200-61604 Floppy Cable B6 A4200-60004 A4.
Field Replaceable Units Exchange and Nonexchange Part Numbers 11 4 Not Shown A4200-84001 A4200- A4200-84025 A4200-84023 A4200-84028 A4200-84024 Model Number Plate C100 Model Number Plate C1 10 Model N.
Field Replaceable Units FRU Removal and Replacement 11 5 FRU Removal and Replacement The procedures in this section describe how to remove system unit FRUs. Observe any notices and prerequi- sites for removing a FRU. Replacement is the reverse of removal, unless noted.
Field Replaceable Units FRU Removal and Replacement 11 6 Figure 29 Removing the Floor Stand 6 Lay the workstation on a flat stable surface, such as a table top or floor. CAUTION: Follow normal ESD, anti-static precautions when handling the workstation or any of its components.
Field Replaceable Units FRU Removal and Replacement 11 7 Storage Tray Assembly Perform the following steps to remove the storage tray assembly from the system unit: 1 Remove the storage tray retaining screw, as shown in Figure 30.
Field Replaceable Units FRU Removal and Replacement 11 8 Disk Interconnect Board Before removing the disk interconnect board, remove the Storage Tray Assembly from the system unit. Perform the following steps to remove the disk inter- connect board from the system unit: 1 Remove the two retaining screws, as shown in Figure 31.
Field Replaceable Units FRU Removal and Replacement 11 9 Storage Tray Bezel Before removing the storage tray bezel, remove the Storage T ray Assembly . 1 T o remove the storage tray bezel, lift up on the top rear edge of the bezel and slide it out from the stor- age tray approximately 1/2-inch, as shown in Figure 32.
Field Replaceable Units FRU Removal and Replacement 120 Disk Filler Panel NOTICE: If you remove a disk filler panel, you must replace it or install a removable media storage device in its place. Before removing a disk filler panel, remove the Stor- age T ray Assembly .
Field Replaceable Units FRU Removal and Replacement 121 Storage Devices Before removing storage devices, remove the Storage Tray Assembly from the system unit. Before removing a hard drive in either of the storage tray’s rear positions, remove the Disk Interconnect board.
Field Replaceable Units FRU Removal and Replacement 122 Figure 34 Removing a Storage Device 3 Slide the device completely out of the storage tray and place it on a static-free surface. When replacing storage devices, refer to the cable routing label on the top of the storage tray .
Field Replaceable Units FRU Removal and Replacement 123 Human Interface Board Before removing the human interface board, perform the following procedures: • Remove the Storage Tray Assembly from the system unit.
Field Replaceable Units FRU Removal and Replacement 124 Main Tray Assembly Perform the following steps to remove the main tray assembly from the system unit: 1 If installed, remove any locking device from the security loop on the rear of the system unit.
Field Replaceable Units FRU Removal and Replacement 125 Removing Memory Modules Before removing memory modules, remove the Main T ray Assembly from the system unit.
Field Replaceable Units FRU Removal and Replacement 126 Figure 38 Memory Module Location (C160L) Figure 39 Memory Module Location (C160, C180XP, C200) Rear of Main Tray Memory Connectors Rear of Main .
Field Replaceable Units FRU Removal and Replacement 127 2 To remove a memory module, push the ejector tabs on each side of the module. Lift the memory module up and out of the connector and place it on a static-free surface. Figure 40 shows how to remove a memory module.
Field Replaceable Units FRU Removal and Replacement 128 2 To install a memory module, close the ejector tabs on each side of the memory connector. This lowers the force needed to seat the memory board. Line the memory module up with the guides, as shown in Figure 41.
Field Replaceable Units FRU Removal and Replacement 129 If only a faulty memory module is replaced, use the pdt clear command in the service menu of the Boot Console Interface.
Field Replaceable Units FRU Removal and Replacement 130 2 To remove a cache module, push the ejector tabs on each side of the module. Lift the cache module up and out of the connector and place it on a static-free surface. Figure 43 shows how to remove a cache module.
Field Replaceable Units FRU Removal and Replacement 131 Installing Cache Modules Before installing cache modules, remove the Main T ray Assembly from the system unit.
Field Replaceable Units FRU Removal and Replacement 132 3 Press firmly and evenly on the cache module to ensure that it is fully seated. 4 To verify that this installation was successful, display the current cache information using the Boot Console Inter- face.
Field Replaceable Units FRU Removal and Replacement 133 Removing PCI, EISA, and GSC Option Boards Before removing PCI, EISA, or GSC option boards from the system unit, remove the Main T ray Assembly from the system unit.
Field Replaceable Units FRU Removal and Replacement 134 Figure 46 Removing the EISA Slider and Retainer 3 Remove the screw from the EISA retainer and remove it, as shown in Figure 46. 4 If you are removing a PCI, EISA, or GSC board grasp it by the edge with both hands and pull it straight out.
Field Replaceable Units FRU Removal and Replacement 135 NOTICE: If you are not replacing the board, perform the following procedure: 1 Install a blank plate in the rear panel, as shown in Figure 47 2 Install the EISA retainer, as shown in Figure 47. 3 On the blank plate, turn the locking knob clockwise to secure blank plate, as shown in Figure 47.
Field Replaceable Units FRU Removal and Replacement 136 EGRAM (Enhanced Graphics RAM) Board Before removing the EGRAM board from the system unit, perform the following procedures: • Remove the Main Tray Assembly from the system unit. • Remove any option boards.
Field Replaceable Units FRU Removal and Replacement 137 2 Use a small needle nose plier to squeeze the tabs on the standoffs while lifting gently on each end of the EGRAM board until the tabs are disengaged from the top of the board.
Field Replaceable Units FRU Removal and Replacement 138 CPU Board Before removing the CPU board, remove the Main T ray Assembly from the system unit. Perform the following steps to remove the CPU board from the system unit: 1 Remove the Main Tray Assembly.
Field Replaceable Units FRU Removal and Replacement 139 Figure 50 Removing the CPU Board (C160L).
Field Replaceable Units FRU Removal and Replacement 140 Figure 51 Removing the CPU Board (C160/180/200/240).
Field Replaceable Units FRU Removal and Replacement 141 4 Slide the CPU board out approximately one inch, then lift it straight up to remove it. If you are reinstalling the same CPU board in the sys- tem, repeat Steps 4 through 1 in reverse order . If you are replacing the existing CPU board with a new one, continue with Step 5.
Field Replaceable Units FRU Removal and Replacement 142 System Fans Before removing the fans, remove the Main T ray Assembly from the system unit. Perform the following steps to remove the system fans. 1 Disconnect the fan connector. 2 Press the retaining clip and swing the fan assembly out from the back panel, as shown in Figure 52 and Figure 53.
Field Replaceable Units FRU Removal and Replacement 143 Figure 53 Removing the CPU Area Fan Assembly 3 Lift the fan assembly up off of the pins..
Field Replaceable Units FRU Removal and Replacement 144 4 Pull the fan retaining clips away from the fan and remove the fan from the fan housing, as shown in Figure 54.
Field Replaceable Units FRU Removal and Replacement 145 Rear Panel Before removing the Rear Panel, perform the follow- ing procedures: • Remove the Main Tray Assembly from the system unit.
Field Replaceable Units FRU Removal and Replacement 146 I/O Board Before removing the I/O board, perform the following procedures: • If you are replacing the original I/O board with a new one, refer to the section, “Determining LAN ID and FDDI ID” below before removing the board.
Field Replaceable Units FRU Removal and Replacement 147 Determining LAN ID and FDDI ID 1 If you are using HP-UX 9.0x, enter the following at the prompt: /etc/lanscan If you are using HP-UX 10.
Field Replaceable Units FRU Removal and Replacement 148 Removing the I/O Board Perform the following steps to remove the I/O board: 1 Pull the ejector handles, as shown in Figure 56. Figure 56 Removing the I/O Board 2 Slide the board out slowly until it stops, then lift it straight up.
Field Replaceable Units FRU Removal and Replacement 149 I/O Extension Board Before removing the I/O extension board, remove the Rear Panel. Perform the following steps to remove the I/O exten- sion board: 1 Remove one screw holding the I/O extension board to the main tray, as shown in Figure 57.
Field Replaceable Units FRU Removal and Replacement 150 Battery Before removing the battery , perform the following procedures: • Remove the Main Tray Assembly • Remove all of the PCI, EISA, and GSC option boards Lift the clip and slip the battery out of its holder , as shown in Figure 58.
Field Replaceable Units FRU Removal and Replacement 151 Backplane Before removing the backplane, perform the following procedures: • Remove the Main Tray Assembly • Remove the CPU Board • Remove.
Field Replaceable Units FRU Removal and Replacement 152 3 Remove the retaining screw from the backplane, as shown in Figure 59. 4 Lift the Backplane up and out, as indicated in Figure 59.
Field Replaceable Units FRU Removal and Replacement 153 Power Supply Before removing the power supply , remove the Main T ray Assembly . T o remove the power supply , loosen the captive screw and slide the power supply out of the chassis, as shown in Figure 60.
Field Replaceable Units FRU Removal and Replacement 154 Power Interconnect Board Before removing the power interconnect board, per- form the following procedures: • Remove the Main Tray Assembly •.
155 6 Diagrams.
Diagrams 156 This chapter provides functional information about the system..
Diagrams System Power 157 System Power Figure 62 shows the power distribution and connec- tions for the C Class power distribution boards. Figure 62 Power Distribution Board The power supply distribut.
Diagrams System Power 158 T able 16 CPU Board Power Pinouts for J10 Pin Number Row D Row C Row B Row A 1 GND GND PWR_RST_CPU_L GND 2 F AMIL Y N12V GND SP ARE5 3 P12V GND_SENSE GND SP ARE4 4 P12V VDD_S.
Diagrams System Power 159 32 VDL GSC0_AD(5) GSC0_AD(6) GSC0_AD(7) 33 VDD GSC0_AD(8) GSC0_AD(9) GSC0_AD(10) 34 VDL GSC0_AD(1 1) GSC0_AD(12) GND 35 VDD GSC0_AD(13) GND GSC0_AD(14) 36 VDL GND GSC0_AD(15).
Diagrams System Power 160 T able 16 lists the pinouts for the power supply connec- tor to the CPU board at J9: T able 17 CPU Board Power Pinouts for J9 Pin Number Row D Row C Row B Row A 1 VDLGND VDD .
Diagrams System Power 161 T able 18 lists the pinouts for floppy drive power: T able 19 lists the pinouts for hard disk drive power: 29 VDL GSC1_LS_L GND GSC1_SYNC_L 30 VDL GSC1_INTERRUPT_L GND GSC1_.
Diagrams System Power 162 T able 20 lists the pinouts for fan power: T able 21 lists the pinouts for the LED connector: 3 GROUND black 4 +5V orange T able 20 Fan Power Pinouts Pin Number Description W.
Diagrams System Block Diagram 163 System Block Diagram The figures in this section show the system unit block diagrams for the C100/1 10, C160L, and the C160/180 workstations.
Diagrams System Block Diagram 164 Figure 63 C100/110 System Unit Functional Block Diagram.
Diagrams System Block Diagram 165 Figure 64 C160L System Unit Functional Block Diagram.
Diagrams System Block Diagram 166 Figure 65 C160/180 System Unit Functional Block Diagram.
Diagrams System Block Diagram 167 Figure 66 C200/240 System Unit Functional Block Diagram.
Diagrams System Block Diagram 168.
169 7 Reference.
Reference 170 This chapter provides part numbers and titles to refer- ence documents..
Reference Installation Manual 171 Installation Manual Har dwar e Installation Car d C Class A4200-90012 Service Manuals Service Handbook C100/C1 10, C160L, and C160/180 W orkstations (this handbook) A.
Reference Reference Manuals 172.
173 8 Service Notes.
Service Notes 174 Place service notes here. __________________________________________ __________________________________________ __________________________________________ ___________________________.
Service Notes 175 __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________.
Service Notes 176.
177 9 Boot Console Interface Model C100/110.
Boot Console Interface Model C100/1 10 178 The Boot Console Interface provides an “interactive” environment after the power-on sequence..
Boot Console Interface Model C100/1 10 Accessing the Boot Console Interface 179 Accessing the Boot Console Interface T o access the boot console interface, follow these steps: NOTICE: This procedure should be done by a system administrator . 1 Close any files and applications on your workstation.
Boot Console Interface Model C100/1 10 Accessing the Boot Console Interface 180 4 Press a key. You will then see the message: Boot terminated The Main Menu of the boot console appears.
Boot Console Interface Model C100/1 10 Boot Console Menus 181 Boot Console Menus The boot console menus follow , showing the various tasks you can perform and the information available. The shortened version of all commands is indicated by the uppercase letters.
Boot Console Interface Model C100/1 10 Boot Console Menus 182 ------ Configuration Menu ----------------------------------------- Command Description ------- ----------- AUto [BOot|SEArch] [ON|OFF] Di.
Boot Console Interface Model C100/1 10 Boot Console Menus 183 ------ Service Menu ----------------------------------------------- --- Command Description ------- ----------- ChassisCodes [<proc>.
Boot Console Interface Model C100/1 10 Searching for Bootable Media 184 Searching for Bootable Media T o list all devices that may contain bootable media, follow the directions in “Accessing the Boo.
Boot Console Interface Model C100/1 10 Searching for Bootable Media 185 Where device_type is one of the following: fwscsi is the built-in fast, wide SCSI bus slot n .
Boot Console Interface Model C100/1 10 Resetting the Workstation 186 Resetting the Workstation T o reset your workstation, press the power switch and let the system perform a soft shutdown.
Boot Console Interface Model C100/1 10 Displaying and Setting Paths 187 Displaying and Setting Paths A path is the hardware address of a device that is attached to the I/O system of your workstation. The path command sets the system paths shown in T able 22.
Boot Console Interface Model C100/1 10 Displaying and Setting Paths 188 The boot paths are displayed in Mnemonic Style Notation , as shown in T able 23.
Boot Console Interface Model C100/1 10 Displaying and Setting Paths 189 T o set a system path to a new value, follow the direc- tions in “Accessing the Boot Console Interface” earlier in this chap.
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 190 Displaying and Setting the Monitor Type Y our system ships from the factory preset to use a monitor with a specific resolution and frequency .
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 191 T able 24 shows the possible combinations of graphics cards and slots. Graphics 3, and Graphics 4 refer to the console paths, GRAPHICS3, and GRAPHICS4, respectively . There is no GRAPHICS 1 or GRAPHICS 2 path.
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 192 Figure 67 shows the physical layout of the EISA/GSC slots from outside the system unit. Figure 67 EISA/GSC Slots from Outside the System Unit Physical slot2 is always reserved for non-graphics cards only .
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 193 Displaying the Current Monitor Configuration T o display the current monitor configuration for your system from the Configuration Menu of the boot con- sole interface, follow the directions in “Accessing the Boot Console Interface” earlier in this chapter .
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 194 Setting the Monitor Type Using the list in the example above, you can set the monitor type for graphics slot3 by typing the follow- ing: monitor graphics3 NOTICE: Y ou can exit at this point by entering x , and the monitor type will not be changed.
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 195 The MONITOR INFORMA TION table reappears with the new monitor shown in slot0. Slot # HPA State ResolutionFrequency Class --------- ----------------- ------------------- ------- graphics3 f4000000 Present Fixed graphics4 f6000000 Empty Current Console Path: core.
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 196 T rying to change the monitor type on an empty slot, fails and gives you this warning message: Configuration Menu: Enter command monitor graphics4 MONITOR INFORMATION WARNING: Intended graphics hardware does not exist.
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 197 Setting the Monitor Type at Power On If you replace your workstation’s monitor with a dif- ferent monitor type, an.
Boot Console Interface Model C100/1 10 Displaying and Setting the Monitor T ype 198 Changing the Console to External Terminal In the event that your console stops displaying to your graphics device, use the following procedure to display to console to an external terminal: 1 Turn system power off.
Boot Console Interface Model C100/1 10 Displaying the Status of the System I/O 199 Displaying the Status of the System I/O The IO command lets you identify all built-in I/O devices and optional I/O devices installed in the option slots. It is available in the Information Menu.
Boot Console Interface Model C100/1 10 Setting the Auto Boot and Auto Search Flags 200 Setting the Auto Boot and Auto Search Flags The auto boot and auto search flags are variables stored in your workstation’ s non-volatile memory . (Non-volatile memory retains its contents even after power is turned off.
Boot Console Interface Model C100/1 10 Setting the Auto Boot and Auto Search Flags 201 T o change the state of the auto boot or auto search flags, type the following at the prompt: auto boot state or auto search state where state is on or off .
Boot Console Interface Model C100/1 10 Displaying and Setting Secure Mode 202 Displaying and Setting Secure Mode The SECure flag is a variable stored in non-volatile memory .
Boot Console Interface Model C100/1 10 Displaying and Setting Fastboot Mode 203 Displaying and Setting Fastboot Mode When fastboot is enabled (set to on ), your worksta- tion does a quick check of the memory and skips I/O interface testing during its power-on self tests.
Boot Console Interface Model C100/1 10 Displaying the LAN Station Address 204 Displaying the LAN Station Address It is sometimes necessary to supply a LAN station address of your workstation to other users.
Boot Console Interface Model C100/1 10 Displaying System Information 205 Displaying System Information The all command allows you to display all the infor- mation shown by the individual Information Menu commands, such as the system’ s processor revision and speed, cache size, memory size, flag settings, and the boot and console paths.
Boot Console Interface Model C100/1 10 Displaying PIM Information 206 Displaying PIM Information The pim command allows you to display the most recent PIM information for the specified fault type.
Boot Console Interface Model C100/1 10 Configure and Display LAN Settings 207 Configure and Display LAN Settings The LanConfig command configures and displays the current LAN settings. The C180, C200 and C240 sys- tems support 10Base-T , 100Base-T and AUI stan- dards.
Boot Console Interface Model C100/1 10 Configure and Display LAN Settings 208 Configuration Menu: Enter command > LanConfig 100/Full_dx T o select the AUI port (10 Mbits/sec, half duplex only), type the following at the prompt: Configuration Menu: Enter command > LanConfig AUI NOTE: The LAN setting defaults to LAN-TP(RJ45).
Boot Console Interface Model C100/1 10 Stable Storage 209 Stable Storage Stable storage is nonvolatile memory associated with each P A-RISC processor module.
Boot Console Interface Model C100/1 10 ISL Environment 210 ISL Environment The ISL environment provides the means to load the operating system (HP-UX) environment. The ISL environment also provides an offline platform to exe- cute diagnostic and utility programs from a boot device when HP-UX does not load.
Boot Console Interface Model C100/1 10 ISL Environment 21 1 2 Answering yes (y) causes the ISL to be loaded from the specified device. After a short time, the following prompt appears on your screen: ISL> ISL is the program that actually controls the loading of the operating system.
Boot Console Interface Model C100/1 10 ISL Environment 212 • conspath - modifies the console path entry in Stable Storage. The entry in Stable Storage for the console device begins at byte address 96 and ends at byte address 127. The entry for the keyboard and mouse devices begins at byte address 160 and ends at 191.
Boot Console Interface Model C100/1 10 Updating System Firmware with ODE 213 Updating System Firmware with ODE The Offline Diagnostic Environment (ODE) consists of diagnostic modules for testing and verifying system operation.
Boot Console Interface Model C100/1 10 Updating System Firmware with ODE 214 T o run the update utility , type run at the UPDATE> prompt. After update loads the new images into mem- ory , it asks if you want to continue the update process, and displays the PDC version of the currently running PDC as well as that of the images that were loaded.
215 10 Boot Console Interface Model C160L/160/180/200/ 240.
Boot Console Interface Model C160L/160/180/200/240 216 The Boot Console Interface provides an “interactive” environment after the power-on sequence.
Boot Console Interface Model C160L/160/180/200/240 Accessing the Boot Console Interface 217 Accessing the Boot Console Interface T o access the boot console interface, follow these steps: NOTICE: This procedure should be done by a system administrator .
Boot Console Interface Model C160L/160/180/200/240 Accessing the Boot Console Interface 218 NOTICE: If you are using a power-saving monitor , you will have less than 10 seconds from the time this message appears to press a key . 4 Press a key. You will then see the message: Boot terminated The Main Menu of the boot console appears.
Boot Console Interface Model C160L/160/180/200/240 Boot Console Menus 219 Boot Console Menus The boot console menus follow , showing the various tasks you can perform and the information available. The shortened version of all commands is indicated by the uppercase letters.
Boot Console Interface Model C160L/160/180/200/240 Boot Console Menus 220 ------ Configuration Menu----------------------------------------- Command Description ------- ----------- AUto [BOot|SEArch] .
Boot Console Interface Model C160L/160/180/200/240 Boot Console Menus 221 ------ Information Menu ------------------------------------------- Command Description ----------- ----------- ALL Display al.
Boot Console Interface Model C160L/160/180/200/240 Boot Console Menus 222 ------ Service Menu ----------------------------------------------- Command Description ------- ----------- ChassisCodes [<.
Boot Console Interface Model C160L/160/180/200/240 Searching for Bootable Media 223 Searching for Bootable Media T o list devices that contain bootable media, follow the directions in “Accessing the.
Boot Console Interface Model C160L/160/180/200/240 Resetting Y our Workstation 224 Resetting Your Workstation T o reset your workstation, follow the directions in “Accessing the Boot Console Interfa.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting Paths 225 Displaying and Setting Paths A path is the hardware address of a device that is attached to the I/O system of your workstation. The path command sets the system paths shown in T able 25.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting Paths 226 The paths are displayed in Mnemonic Style Notation, as shown in T able 26.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting Paths 227 T o set a system path to a new value, follow the direc- tions in “Accessing the Boot Console Interface” ear- lie.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor T ype 228 Displaying and Setting the Monitor Type Y our system ships from the factory preset to use a monitor with a specific resolution and frequency .
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor T ype 229 T o display the current graphics and console informa- tion, enter the following command; monitor The cor.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor T ype 230 Displaying the Current Monitor Configuration T o display the current monitor configuration for your sys.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor T ype 231 Setting the Monitor Type Y ou can set the monitor type for a graphics adapter by typing the following: Configuration Menu: Enter command> monitor graphics( n ) tt Where n is the number of the graphics adapter and tt is the monitor type.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor T ype 232 T o set the monitor type for graphics(0) to monitor type 2 you would enter the following; Configuration Menu: Enter command > monitor graphics(0) 2 Configuration Menu: Enter command > monitor graphics(0) 2 This will take effect on the next reboot.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor T ype 233 Setting the Monitor Type at Power On If you replace your workstation’s monitor with a dif- ferent moni.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor T ype 234 At this point, the new monitor type is active, but not saved. Because you didn’t save the monitor type, the next time you reboot the system the original monitor type will be used.
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Monitor T ype 235 Changing the Console to External Terminal In the event that your console stops displaying to your graphics device, use the following procedure to display to console to an external terminal: 1 Turn system power off.
Boot Console Interface Model C160L/160/180/200/240 Displaying the Status of the System I/O 236 Displaying the Status of the System I/O The IO command lets you identify all built-in I/O devices and optional I/O devices installed in the option slots. It is available in the Information Menu.
Boot Console Interface Model C160L/160/180/200/240 Setting the Auto Boot and Auto Search Flags 237 Setting the Auto Boot and Auto Search Flags auto boot and auto sear ch are variables stored in your workstation’ s nonvolatile memory . (Nonvolatile mem- ory retains its contents even after power is turned off.
Boot Console Interface Model C160L/160/180/200/240 Setting the Auto Boot and Auto Search Flags 238 T o change the state of the auto boot or auto search flags, type the following at the prompt: auto boot state or auto search state where state is on or off .
Boot Console Interface Model C160L/160/180/200/240 Displaying and Setting the Fastboot Mode 239 Displaying and Setting the Fastboot Mode Access fastboot from the configuration menu. When fastboot is enabled (set to on ), your worksta- tion does a quick check of the memory and skips I/O interface testing during its power-on self tests.
Boot Console Interface Model C160L/160/180/200/240 Displaying the LAN Station Address 240 Displaying the LAN Station Address It is sometimes necessary to supply a LAN station address of your workstation to other users.
Boot Console Interface Model C160L/160/180/200/240 Configure and Display LAN Settings 241 Configure and Display LAN Settings The LanConfig command configures and displays the current LAN settings. The C180, C200 and C240 sys- tems support 10Base-T , 100Base-T and AUI stan- dards.
Boot Console Interface Model C160L/160/180/200/240 Configure and Display LAN Settings 242 Configuration Menu: Enter command > LanConfig 100/Full_dx T o select the AUI port (10 Mbits/sec, half duplex only), type the following at the prompt: Configuration Menu: Enter command > LanConfig AUI NOTE: The LAN setting defaults to LAN-TP(RJ45).
Boot Console Interface Model C160L/160/180/200/240 Displaying System Information 243 Displaying System Information The all command allows you to display the system’ s processor revision and speed, cache size, memory size, flag settings, and the boot and console paths.
Boot Console Interface Model C160L/160/180/200/240 Displaying PIM Information 244 Displaying PIM Information The pim command allows you to display the most recent PIM information for the specified fault type.
Boot Console Interface Model C160L/160/180/200/240 Stable Storage 245 Stable Storage Stable storage is nonvolatile memory associated with each P A-RISC processor module.
Boot Console Interface Model C160L/160/180/200/240 ISL Environment 246 ISL Environment The ISL environment provides the means to load the operating system (HP-UX) environment. The ISL environment also provides an offline platform to exe- cute diagnostic and utility programs from a boot device when HP-UX does not load.
Boot Console Interface Model C160L/160/180/200/240 ISL Environment 247 2 Answering yes (y) causes the ISL to be loaded from the specified device. After a short time, the following prompt appears on your screen: ISL> ISL is the program that actually controls the loading of the operating system.
Boot Console Interface Model C160L/160/180/200/240 ISL Environment 248 • conspath - modifies the console path entry in Stable Storage. The entry in Stable Storage for the console device begins at byte address 96 and ends at byte address 127. The entry for the keyboard and mouse devices begins at byte address 160 and ends at 191.
Boot Console Interface Model C160L/160/180/200/240 Updating System Firmware with ODE 249 Updating System Firmware with ODE The Offline Diagnostic Environment (ODE) consists of diagnostic modules for testing and verifying system operation.
Boot Console Interface Model C160L/160/180/200/240 Updating System Firmware with ODE 250 The following commands may be entered at the UPDATE> prompt: • help - prints a one line description of each of the available commands in the update utility. • info - prints information on how to use the update utility.
Index 251 A audio CODEC, 17 features, 16 headphone jack, 8 IN,, 15 input, 16 microphone jack, 8 mute button, 8 OUT,, 15 outpu, 17 volume control, 8 auto boot flag, changing state of, 201 auto boot,, 2.
Index 252 F fast boot disabling, 203 displaying status of, 203 enabling, 203 fast boot mode,, 203 fastboot disabling,, 239 displaying status,, 207, 208, 239, 241, 242 enabling,, 239 fastboot,, 239 fla.
Index 253 network, 19 parallel I/O, 19 power cord, 21 RS-232 serial I/O, 20 SCSI, 21 TOC, 21 regulations acoustics,, ix laser safety statement,, xi safety statement,, x S SCSI default ID, 40 selftest .
Index 254.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté HP (Hewlett-Packard) C160L c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du HP (Hewlett-Packard) C160L - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation HP (Hewlett-Packard) C160L, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le HP (Hewlett-Packard) C160L va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le HP (Hewlett-Packard) C160L, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du HP (Hewlett-Packard) C160L.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le HP (Hewlett-Packard) C160L. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei HP (Hewlett-Packard) C160L ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
