Manuel d'utilisation / d'entretien du produit F58F du fabricant Honeywell
Aller à la page of 28
69-0764—2 Copyright © 1998 Honeywell Inc. All Rights Reserved F58F ELECTRONIC AIR CLEANER OWNER’S GUIDE 69-0764-2.
69-0764—2.
69-0764—2 CONTENTS PAGE THE AIR CLEANER MONITOR 2 OPERATING YOUR ELECTRONIC AIR CLEANER 3 GETTING THE MOST FROM YOUR ELECTRONIC AIR CLEANER 5 CLEANING THE ELECTRONIC CELLS AND PREFILTERS 7 HOW ELECT.
69-0764—2 AIR CLEANER MONITOR The optional W8600F Air Cleaner Monitor may be added to your air cleaner system to provide convenient indication of system performance.
69-0764—2 When the fan and air cleaner come on, the neon indicator lights. If your air cleaner is equipped with a wall- mounted W8600F Air Cleaner Monitor (see page 2), the ON indicator will be active whenever the air cleaner is in operation . Of course, the system fan will also be running.
69-0764—2 If you don’t want the air cleaner to run, set the ON-OFF switch to OFF to turn off the air cleaner. Your furnace and air conditioner will still operate normally, but without the added benefit of air cleaning. Normally, this switch should be ON at all times.
69-0764—2 For greatest benefit, the air cleaner should run all the time. To do this, set the fan switch on your thermostat to ON, and make sure the air cleaner is switched ON. The fan and air cleaner will run even when the furnace or air conditioner is off.
69-0764—2 If your system includes an atomizing humidifier, you may want to install a standard furnace filter between the humidifier and the air cleaner. This filter would keep the humidifier spray’s mineral deposits from collecting on the air cleaner.
69-0764—2 CA UTION Sharp edges. Can cause personal injury. Carefully handle the cells or wear protective gloves to avoid cuts from the sharp metal edges. To ensure optimum performance from the air cleaner, the cells and prefilters must be cleaned regularly—every one to six months.
69-0764—2 If your air cleaner has a W8600F Air Cleaner Monitor, the SERVICE indicator will activate when it is time to wash the cells and prefilters. Wash them following the instructions starting on page 9. To turn the SERVICE indicator off, press the reset button on the lower right of the W8600F (see picture below).
69-0764—2 CA UTION Burn hazard. Can cause personal injury. Allow the cells to cool completely in the dishwasher at the end of the wash cycle or wear protective gloves to avoid burns. Hot water can accumulate in the tubes supporting the collector plates.
69-0764—2 STEP 1 Put the cells on the lower rack of the dish- washer with the airflow arrow pointing up. It may be necessary to remove the upper rack.
69-0764—2 STEP 1 Use a large enough container, such as a laundry tub or trash container, to hold one or both cells. NOTE: Sharp corners on the cells can scratch the surface of a bathtub. STEP 2 Dissolve about 3/4 cup of automatic dishwasher detergent per cell in enough hot water to cover the cells.
69-0764—2 Replacing electronic air cleaner components STEP 1 Inspect the cells for broken ionizer wires and bent collector plates. Repair as necessary or take to a Honeywell Authorized Air Cleaner Repair Station. STEP 2 Slide the prefilters into the upstream prefilter guides.
69-0764—2 The particles removed by the electronic air cleaner tend to be very small—less than 10 microns. But what is a 10 micron particle? Well, the eye of an average size sewing needle is about 750 microns across, and the dot in the i in the word micron is about 400 microns.
69-0764—2 First, large particles (lint, hair) are caught by the prefilters. Then, as the dirty air passes through the intense high voltage electric field surround- ing the ionizer wires, all particles, even the smallest are given an electric charge.
69-0764—2 The regular furnace filter collects mainly large, visible particles that reach the filter. Its main purpose is to protect the furnace and air conditioner blower. The electronic air cleaner collects these large particles, plus many of the smaller, mostly invisible particles.
69-0764—2 Odors are gases, not particles. They cannot be removed by the air cleaner or by any other filter designed to remove particles. However, some gases can be trapped by an activated carbon filter or diluted with outdoor air.
69-0764—2 If desired, the ozone generated by the air cleaner can be reduced by asking your dealer to: • Install an activated carbon filter downstream of the air cleaner, or • Adjust the air cleaner power supply to reduce ozone production.
69-0764—2 If your air cleaner is equipped with the optional W8600F Air Cleaner Monitor, the SERVICE and FAULT indicator on the W8600F will remind you that a cell and prefilter washing is due and tell you when the system isn’t operating properly.
69-0764—2 5. Press the test button. A snapping sound indicates the air cleaner is operating properly, but the neon light is not working. If there is no snapping sound, make sure the appropriate fuse or circuit breaker is OK. 1. Cell and prefilter washing is due; wash as soon as possible.
69-0764—2 Honeywell guarantees your indoor heating/ cooling coil will maintain optimum efficiency and energy savings for a minimum of 10 years if your new Honeywell Electronic Air Cleaner is install.
69-0764—2 For Honeywell Electronic Air Cleaners installed on a heat pump, air conditioner or high efficiency furnace that is either new or less than one year old , send copies of invoices verifying… • Purchase of a new Honeywell Electronic Air Cleaner.
69-0764—2 22 Perfect Climate® CONTROLS FOR ADDED COMFORT AND CONVENIENCE CONDITIONED AIR CONDITIONED AIR RETURN AIR REGISTER SUPPLY AIR REGISTER STALE AIR EXHAUST FRESH AIR INTAKE HONEYWELL HOME VE.
69-0764—2 LIMITED TWO-YEAR WARRANTY Honeywell warrants this product to be free from defects in the workman- ship or materials, under normal use and service, for a period of two (2) years from the date of purchase by the consumer.
69-0764—2.
69-0764—2.
69-0764—2 69-0764—2 J.H. Rev. 7-98 www.honeywell.com/yourhome Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Honeywell F58F c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Honeywell F58F - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Honeywell F58F, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Honeywell F58F va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Honeywell F58F, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Honeywell F58F.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Honeywell F58F. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Honeywell F58F ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
