Manuel d'utilisation / d'entretien du produit 08E91-E22-100B du fabricant Honda
Aller à la page of 22
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 1 of 22 08E92-SVA-1B00-91 FEB 2008 200 6-2008 CIVIC 2-DOOR (A/T ONLY) REMOTE ENGINE STARTER SYSTEM INSTALLATION INSTRUCTIONS Accessory Application Publications No.
2 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 7 Foam cushion tapes Flange nut Clip Green relay (5-pin) Template Illustration of the Engine Starter System.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 3 of 22 Setting the Control Unit 3. Get the control unit. Using a small flat-tip screwdriver, adjust the switches on the control unit to the locations shown. Using a isopropyl alcohol on a shop towel, clean the area where the protective tape will attach.
4 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 9. Remove the driver’s dashboard lower cover (eight clips). 5202121T DRIVER’S DASHBOARD LOWER COVER 8 CLIPS 5202112T 8. If equipped, remove the driver’s dashboard under cover (turn the knob counterclockwise, and release two clips and pin).
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 5 of 22 1 2. Remove the column lower cover (two self-tapping screws and one screw). 5308530T 2 SELF-TAPPING SCREWS SCREW COLUMN LOWER COVER 1 0 . Lower the tilt lever, and pull the steering wheel toward you.
6 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 1 4 . Remove the sunvisor holders. Using a small flat- tip screwdriver, push the hook, and turn the holder 90°, then pull it out.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 7 of 22 1 9 . Pull away the weatherstrip from the left front pillar trim. Remove the left front pillar trim (two clips). 5202100T 2 CLIPS LEFT FRONT PILLAR TRIM WEATHERSTRIP 2 0 .
8 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 2 4. Measure the antenna cable as shown. Attach the three foam cushion tapes to the antenna cable in the measurement shown. 2 5 . Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 9 of 22 2 8. Route the antenna cable under the roof liner towards the driver’s side of vehicle, and down along the vehicle harness. Be careful not to crease the roof liner.
10 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 3 2 . Secure the antenna cable to the vehicle harness with a wire tie. Secure the wire tie between the vehicle harness branching points. 6D01281T VEHICLE HARNESS WIRE TIE ANTENNA CABLE BRANCHING POINT Installing the Control Unit Bracket 3 3 .
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 11 of 22 3 5 . Install the four relays to the engine starter harness relay blocks. Be careful to install the relays properly, or a malfunction will result. Routing the Engine Starter Harness 3 4 .
12 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 3 8 . Disconnect the vehicle 8-pin connector on the rear of the wiper switch and plug the engine starter harness 8-pin connectors into the vehicle 8-pin connector.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 13 of 22 4 0 . Wrap the vehicle 7-pin connector with one foam cushion tape, then place the vehicle 7-pin connector into the gap of the column. 6D01111T VEHICLE 7-PIN CONNECTOR (brown) (Squeeze into this area.
14 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 4 7 . Secure the engine starter harness to the vehicle harness using a wire tie: • With driver's dashboard under cover: Secure in the hole opened in the instrument panel.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 15 of 22 4 9. Disconnect the vehicle 42-pin, 4-pin, and 2-pin connectors. 5 1 . Wrap foam cushion tape to the vehicle 2-pin and 4-pin connectors and secure them with a wire tie.
16 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 5 4 . Install the clip from the engine starter harness to the fuse box bracket behind the fuse box.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 17 of 22 6D01312T ANTENNA CABLE TERMINAL (Connect first.) FRONT CONTROL UNIT ENGINE STARTER HARNESS 18-PIN CONNECTOR CONTROL UNIT BRACKET 5 7 . Install the control unit on the control unit bracket.
18 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 752501AS CAR ICON 752502AS CHECK BUTTON Input the VIN and other required information. 752504AS Select “R/C ENG STARTER.” CHECK BUTTON 752503AS Select “Honda Systems.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 19 of 22 752505AS “REMARKS” message CHECK BUTTON 752506AS Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.” CHECK BUTTON 752507AS “Obtain PCM-code" message CHECK BUTTON 752509AS Input the PCM code.
20 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 1 1 . The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click the check button. 1 2. The following message will display: Check that the engine can be started by the Transmitter.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 21 of 22 732904A Y DISPLAY COMMAND BUTTON START BUTTON TRANSMITTER STOP BUTTON FUNCTION CHECK Operating Conditions • The hood is closed. • The shift lever is in Park.
22 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. How to Program an Additonal Transmitter 1. Connect the HDS to the data link connector. 2. Start the HDS and click on the car icon. 3. Input the vehicle's VIN and other required information.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Honda 08E91-E22-100B c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Honda 08E91-E22-100B - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Honda 08E91-E22-100B, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Honda 08E91-E22-100B va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Honda 08E91-E22-100B, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Honda 08E91-E22-100B.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Honda 08E91-E22-100B. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Honda 08E91-E22-100B ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
