Manuel d'utilisation / d'entretien du produit ML-114629 du fabricant Hobart
Aller à la page of 24
— 1 — MODEL HFD/HFC SERIES ELECTRIC FR YERS MODELS HFD40 ML-114624 HFD50 ML-114625 HFD225 ML-114626 HFD85 ML-114627 HFC40 ML-114628 HFC50 ML-114629 HFC225 ML-114630 HFC85 ML-114631 HFO15 ML-114632 HFO21 ML-114633 FORM 33637 Rev.
— 2 — T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
— 3 — Installation, Operation and Care of MODEL HFD/HFC SERIES ELECTRIC FR YERS SA VE THESE INSTR UCTIONS FOR FUTURE USE GENERAL Hobart HFD/HFC Series Electric Fryers are available in 3 sizes with an array of features and options for a range of commercial fryer applications.
— 4 — HF Series Fryer — Construction Features Model Filter Ready Battery Battery Configuration Interplumbing HFD40/HFC40 Opt. (Use HMF50) Opt. Opt. HFD50/HFC50 Opt. (Use HMF50) Opt. Opt. HFD225 Opt. (Use HMF50) Opt. Opt. HFD85/HFC85 Opt. (Use HMF85) Opt.
— 5 — Field Installable Accessories: Factory Installed Only • Casters • Fat Melt • Twin Baskets • Basket Lift • Single Baskets • S/S Tank • Tri Baskets (HF85 only) • S/S Sides • .
— 6 — INST ALLA TION Before installing the fryer, verify that the electrical service agrees with the specifications on the fryer data plate which is located on the inside of the door panel. UNPACKING Immediately after unpacking the fryer, check for possible shipping damage.
— 7 — Casters (Optional) It is recommended that casters be installed on all batteried appliances. A strain relief is supplied to protect the electrical supply line. If it is necessary to disconnect the restraint, unplug electrical supply before disconnection.
— 8 — I Place fryer as near to its final position as possible. Connect 3 phase line to X, Y and Z of terminal block. To reach terminal block, remove electric cover plate from fryer.
— 9 — OPERA TION WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK.
— 10 — ADDING SOLID SHORTENING If replacing shortening, place the block of shortening in the room with the fryer for 1 to 2 hours before using. This will soften the shortening and make it easier to divide.
— 11 — HFD FRYER HFD FRYER TIMED BASKETLIFT OPTION PUSH TO TIME BASKET LIFT CONTROL 15 MIN. TIMER 0 1 2 3 4 6 7 10 11 15 9 8 12 13 5 14 PUSH TO TIME BASKET LIFT CONTROL 15 MIN. TIMER 0 1 2 3 4 6 7 10 11 15 9 8 12 13 5 14 PL-52239 MELT FRY 1ST 2ND OFF ON P O W E R TROUBLE HEATING HIGH LIMIT CONTROLS — HFD SERIES (Fig.
— 12 — MELTING SOLID SHORTENING (Model HFD) To begin the melt cycle, push the power switch to ON and push the Melt/Fry switch to MELT. When oil has melted, push the Melt/Fry switch to FRY.
— 13 — FRYING (All Models) Heat shortening to set temperature. (For Model HFC Fryers, refer to computer controller instructions starting on page 16 of this manual.) Pieces of product to be fried should be about the same size to ensure the same doneness.
— 14 — Always filter the shortening while liquified. A cold fryer will not drain properly because the shortening under the cold zone area will remain hard, even if the heat is on for a few minutes. If necessary, the clean-out rod may be used to carefully stir up hard fat to an area above the cold zone (see Fig.
— 15 — PL-40858-1 V AL VE RETURN LINE Battery Interplumbing (Optional) A battery of fryers equipped with optional interplumbing connects the fry tanks to a common drain. Each tank has an individual drain valve; these should only be opened one at a time.
— 16 — POWER ENTER EXIT 12 3 45 6 78 9 IDLE OIL TEMP MANUAL FRENCH FR I ES START STOP START STOP PL-52208 CONTROLS — HFC Series (Fig. 5) Fig. 5 DISPLAY — A twelve character display provides information during operation. HEAT — HEAT indicator (in LED display) is lit when burners are on, not lit when off.
— 17 — POWER-UP After being turned on, the control executes a self-check routine. See ERROR MESSAGES, page 23. After going through the self-check routine, the control enters either Fat Melt or Heating mode.
— 18 — COOKING DISPLAY 1. Press a Product Pad [1 - 8]... FRENCH FRIES 2. Load basket. Press left or right START/STOP Pad and lower basket. Timer counts down...* XX:XX 3. When finished, buzzer sounds...* DONE 4. Press left or right START/STOP Pad to stop buzzer.
— 19 — DURING SLACK PERIODS If the fryer is not going to be used for an extended period, oil life is enhanced by pressing IDLE if SETBACK is enabled. With the setback feature enabled, after 30 minutes of non-use, the fryer automatically assumes Idle mode where it maintains 275 ° F (135 ° C) temperature.
— 20 — DEFINITIONS — EDIT PRODUCT PRODUCT KEY = The Product Pad, (1 - 8) PRODUCT NAME = any 12 alpha characters. COOK TIME = Minutes: Seconds of cooking duration. Controls basket lifts and buzzer. Elastic time compensates for under- or over-temperature.
— 21 — EDIT PRODUCT To Add or Change a Product Cook Cycle… DISPLAY INSTRUCTION READY Press 2 & 3 simultaneously. -FUNCTIONS- Press ▼ . EDIT PRODUCT Press ENTER. PRODUCT KEY Press Pad Number (1-8). PRODUCT NAME Press ENTER. Enter the product name.
— 22 — SELECT MELT ▲▼ toggles MELT DISABLE or MELT ENABLE. ENABLE is required when using solid shortening to automatically MELT if below 135 ° F (57 ° C). DISPLAY INSTRUCTION READY Press 2 & 3 simultaneously. -FUNCTIONS- Press ▼ . EDIT PRODUCT Press ▼ .
— 23 — OIL TIMER The controller will alert the operator when the oil needs to be changed. OIL TM = XXX sets the number of hours before the alert will be given. DISPLAY INSTRUCTION READY Press 2 & 3 simultaneously. -FUNCTIONS- Press ▼ . EDIT PRODUCT Press ▼ .
— 24 — DO NOT use a scouring pad or harsh cleaners on the computer keypad, especially the display area. Weekly or as Required 1. Once the shortening has been drained, flush out scraps and sediment with a small amount of warm shortening. Allow the tank to drain thoroughly.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Hobart ML-114629 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Hobart ML-114629 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Hobart ML-114629, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Hobart ML-114629 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Hobart ML-114629, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Hobart ML-114629.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Hobart ML-114629. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Hobart ML-114629 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
