Manuel d'utilisation / d'entretien du produit ML-110973 du fabricant Hobart
Aller à la page of 20
MODEL AM14F , AM14T , & AM14TC DISHW ASHERS MODELS AM14F ML-110975 AM14T ML-110973 AM14TC ML-110974 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.
– 2 – POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IMPORT ANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNIT(S) AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE.
– 3 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation, and Care of MODEL AM14F , AM14T , AM14TC DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL The AM14T, AM14TC, and AM14F dishwashers are semi-automatic rack-type machines. On model AM14T (Fig. 1) the doors open on opposite sides of the machine allowing the rack to move straight through.
– 5 – DO NOT attempt to operate this dishwasher in the chemical sanitizing mode without a properly installed, NSF-listed, chemical sanitizer feeder (not supplied with machine). Contact an authorized detergent representative for information about a chemical sanitizer feeder.
– 6 – On models AM14T and AM14TC, dish tables should be turned down and fitted into the dishwasher (Fig. 2). Use an NSF approved sealer between table and tank lip to prevent leakage. Fasten the tables to the tank lip with truss head screws. Dish tables are not required with model AM14F.
– 7 – WATER CONNECTION A suitable water hammer arrestor should be installed in the water line just ahead of the dishwasher. Without Electric or Gas Booster Water Heater The water supply line is connected to the line strainer (Fig. 1) with 3 / 4 " pipe.
– 8 – Static inlet gas pressure should not exceed 14" W.C. for either natural or propane gas. The minimum value is for purpose of input adjustment. The gas valve (Fig. 3) is provided with a pressure tap to measure the gas pressure downstream, which is also the manifold pressure.
– 9 – VENTING REQUIREMENTS — WITH GAS TANK HEAT The Hobart AM14F / AM14T / AM14TC dishwasher equipped for gas tank heat is not provided with a flue collar and is not intended to have the flue directly connected to a ventilation system. However, the products of combustion must be vented to the outside air.
– 10 – The Rate of air flow required for a vent hood is calculated using the following definitions (Fig. 6): Q = Rate of Air Flow in Cubic Feet Per Minute or [ CFM ] Required for the Hood. A = Area of Hood Opening = (L x W) in Feet 2 D = Clearance Height = Distance in Feet from lower lip of hood to top of dishwasher chamber.
– 11 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT.
– 12 – OPTIONAL EQUIPMENT CONNECTIONS — Vent Fan and Gas Booster WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.
– 13 – DETERGENT, RINSE AID, OR SANITIZER DISPENSERS — Tubing Installation All detergent, rinse aid, and / or sanitizer dispensers must have all connections sealed against leakage.
– 14 – OPTIONAL EQUIPMENT CONNECTIONS — Detergent, Rinse Aid, Sanitizer Dispensers WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.
– 15 – Fig. 13 PO W ER O N / O F F FILL CYCLE WASH 1 2 4 6 Power Switch Cycle Switch Wash / Fill Switch PL-52759 Fig. 11 PL-41 178-1 MANUAL / AUTO SWITCH W ASH / RINSE SWITCH POWER SWITCH READOUT .
– 16 – Models AM14T / AM14TC In Automatic mode, the M ANUAL / A UTO switch (Fig. 12) is on A UTOMATIC and the W ASH / R INSE switch is O FF . The wash and rinse cycles begin automatically. The wash cycle begins when the machine doors are closed. The rinse cycle begins when the wash cycle is completed.
– 17 – PL-40468-1 AM14T Shown Rinse Nozzle Knurled Disk Rinse Arm Wash Arm PL-40809-1 AM14T Shown Rinse Nozzle Rinse arm W ash arm Knurled Disk – Unscrew and support both arms on release. CLEANING T he machine m ust b e thoroughly cleaned at the end of each working shift or at least daily.
– 18 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY (BOTH DISHWASHER AND BOOSTER IF APPLICABLE) AND PLACE A TAG(S) AT THE DISCONNECT SWITCH(ES) TO INDICATE THE CIRCUIT(S) ARE BEING WORKED ON BEFORE BEGINNING ANY MAINTENANCE PROCEDURE. Wash Arms Upper and lower wash and rinse arms (Figs.
– 19 – TROUBLESHOOTING Manual Reset Button on Pump Motor The motor is equipped with a gray manual reset button near the end cover of the motor. If the pump motor becomes overheated, the thermal overload protector will cause the motor to not operate.
– 20 – FORM 34555 ( Dec. 2000 ) PRINTED IN U.S.A. SYMPTOM POSSIBLE CAUSE Inadequate rinse or rinse water 1. Dirty line strainer causing reduced water flow. Turn off water supply, temperature is too low. remove strainer cap, withdraw and clean screen.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Hobart ML-110973 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Hobart ML-110973 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Hobart ML-110973, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Hobart ML-110973 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Hobart ML-110973, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Hobart ML-110973.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Hobart ML-110973. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Hobart ML-110973 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
