Manuel d'utilisation / d'entretien du produit P43 du fabricant Harman Stove Company
Aller à la page of 32
R1 P43 Pellet Stove Owners Manual SA VE THESE INSTRUCTIONS. Installation & Operating Manual R1 “Ce manuel est disponible en Français sur demande” SAFETY NOTICE PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INST ALL AND USE YOUR NEW ROOM HEA TER. F AILURE TO FOLLOW INSTRUCTIONS MA Y RESUL T IN PROPERTY DAMAGE, BODIL Y INJUR Y , OR EVEN DEA TH.
2 P43 Pellet Stove Harman PP38+/P43 Pellet Stove Label measures: 4-3/8" high X 9-3/4"wide MINIMUM CLEARANCES TO COMBUSTIBLES: SIDEWALL T O STOVE 16" 10" BACKWALL T O STOVE 2" .
3 P43 Pellet Stove Safety Information 4 Installation 5 V enting 7 ESP Control 14 Automatic Operation 15 Manual Operation 18 Low Draft V oltage Adjustment 20 Room Sensor 21 Maintenance 22 T rouble Shoo.
4 P43 Pellet Stove DO NOT INST ALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT . DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SER VING ANOTHER APPLIANCE. MOBILE HOME INST ALLA TION SHOULD BE DONE IN ACCORDANCE WITH THE MANUF ACTURED HOME AND SAFETY ST ANDARD (HUD), CFR 3280, P ART 24.
5 P43 Pellet Stove Assembly and Installation Unpacking The P43 is bolted (1/4 x 1" hex head bolts) to the skid to prevent movement during shipping. T o free the stove from the skid you must remove the hold-down bolts in the rear of the pedestal base.
6 P43 Pellet Stove Installing Place the stove on a noncombustible oor protector that extends a minimum of 6 inches to the front, (mea- sured from the glass) 6 inches to the sides and 1 inch to the rear of the hopper .
7 P43 Pellet Stove V enting Requirements for T erminating the V enting W ARNING: V enting terminals must not be recessed into a wall or siding. NOTE: Only approved pellet vent pipe, wall pass- throughs, and re stops should be used when venting through combustible materials.
8 P43 Pellet Stove V enting A co mb us ti on b lo we r is us ed t o ext ra ct t he combustion gases from the rebox. This causes a negative pressure in the rebox and a positive pres - sure in the venting system as shown in Fig.
9 P43 Pellet Stove Outside air ex pipe goes here. Inlet Cover part# 1-10-08542 Flex pipe part# 1-00-08543 (25') Outside Air Here a refourbenetsof outside air: 1. Having air introduced from outside the living area boosts thermal efciency .
10 P43 Pellet Stove #2 Preferred method This method also provides excellent venting for normal operation but requires the stove to be installed farther from the wall. The vertical portion of the vent should be three to ve feet high and at lea st thre e i nch es fro m a co mbu sti ble w all .
1 1 P43 Pellet Stove #4 Installing into an existing chimney This method provides excellent venting for normal operation. This method also provides natural draft in the event of a power failure. If the chimney condition is questionable* you may want to install a liner as in method #7.
12 P43 Pellet Stove #6 Installing into an existing replace chimney This method provides excellent venting for normal operation. This method also provides natural draft in the event of a power failure. In some places in the US and Canada it is re- quired that the vent pipe extend all the way to the top of the chimney .
13 P43 Pellet Stove #8 Installing through the ceiling Through the ceiling vent, follow PLvent manufacturers recommendations when using wall and ceiling pass through.
14 P43 Pellet Stove P43 AUTOMA TIC IGNITION ESP CONTROL Feed adjuster Sets the maximum feed rate T est Runs all motors at full speed for one minut e to check operation. After two minutes the stove will go to minimum burn and the blowers will alternate from high to low every minute to remin d you that you are still in "T est Mode".
15 P43 Pellet Stove P43 AUTOMA TIC IGNITION/OPERA TION Room T emperature Mode: This setting, see above, will produce a room temperature of 70 degrees with the distribution blower at medium speed. The P43 is a fully automatic stove that features two op era ting mod es ; Stov e T em pera ture Mod e and Roo m T emperature Mode .
16 P43 Pellet Stove Stove T emperature Mode In the Stove T emperature Mode and with the igniter toggle switch in the Auto position, the stove will light automa tically and can be adjusted to the desire d setting using the same temperature control dial as is used in the Room T emperature Mode.
17 P43 Pellet Stove Igniter Switch to"AUTO"(up position) Make sure the unit is plugged into a 120 V AC, 60 HZ electrical source. The power light should be the only light lit. 1. T urn Mode Selector to "OFF". 2. Fill hopper with pellets.
18 P43 Pellet Stove The P43 Pellet Stove is capable of manual operation. This also allows the operator to manually control operation during an emergency (i.e. igniter failure, when using a 502H battery backup, as opposed to the 512H, or when using certain generators.
19 P43 Pellet Stove P43 MANUAL ST ART UP Igniter Switch to"MANUAL" (down position) Make sure the unit is plugged into a 120 V AC, 60 HZ electrical source. The power light should be the only light lit. 1. T urn FEED ADJUSTER to desired feed rate .
20 P43 Pellet Stove These units are pre-tested at the factory with exactly 120 V olts A.C., 60 Hz. They are checked and adjusted for rebox tightness, gasket leakage, motor operation and igniter operation. The P43 is then factory set at a mid -poi nt adju stme nt and in most case s will not need any adj ustm ent s.
21 P43 Pellet Stove The room sensor is a small temperature sensor on the end of a 60" wire. This sensor is installed much like a standard wall thermostat. Because it is so small, it can be hidden along the trim of a door- way or even up the leg of a coffee table.
22 P43 Pellet Stove Removing Ashes: When approximately 1 ton of pellets has been burned, it will be necessary to empty the ash pan. Ash es sh oul d be pla ced in a meta l cont ain er with a tight tting lid.
23 P43 Pellet Stove Exposed blower wheel and ue opening, NOTE: ESP probe is visible. Blower cover removed. ESP probe 8. Clean the combustion blower wheel with a brush and a vacuum cleaner .
24 P43 Pellet Stove Burn Pot Cleaning and Maintenance 1. Scrape the top holed surface and sides of the burn pot. (Fig 33) It is not neces sary to comple tely remove all material from the burn pot. The excess will be pushed out during the next use. 2. Loosen the (2) wing thumb screws on the lower front angle of the burn pot.
25 P43 Pellet Stove P43 Maintenance - Cleaning the Feeder Body Pellet nes will accumulate in the feeder body over a period of time; therefore, a yearly inspection and cleaning of this area must be performed. T ocleanoutnes: 1.
26 P43 Pellet Stove FEEDER DOES NOT FEED 1. No pellets in hopper . 2. Firebox draft may be too low for low draft pressure switch in feeder circuit to operate. Check for closed doors , loose or missing gasket on doors or hopper lid, or a faulty pressure switch.
27 P43 Pellet Stove P43 Feeder.
28 P43 Pellet Stove Weight 212 lbs. Blower 135 cfm Feed Rate approximate .75lb. to 5.5 lbs per hr Hopper Capacity 50 lbs Fuel Wood Pellets Flue Size 3 inch Outside Air Size 2 3/8" I.D. inch Fuse Rating 6 amp P43 Specications 12.375" 5.25" 32" 9" 22" 28.
29 P43 Pellet Stove OPTIONS Side Heat Shields Side heat shields are available to reduce the clearance to combustible materials. Part #1-00-00000 Hopper Extension The hoppe r ext ensi on allows you to put more pellet fuel in the hopper and extends burn time on one load of pellets.
30 P43 Pellet Stove P43 Wiring Diagram.
31 P43 Pellet Stove Description Part Number Hopper Gasket(5 ft.) 0-88-00248 Ash Pan Assembly 1-10-7738108 Burn Pot Weldment 1-10-00675 Right Rear Shield 2-00-773828-1P Left Rear Shield 2-00-773828-2P .
HARMAN GOLD W ARRANTY 6 YEAR TRANSFERABLE LIMITED W ARRANTY (Residential) 1 YEAR LIMITED W ARRANTY (Commercial) Harman warrants its products to be free from defects in material or workmanship, in norm.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Harman Stove Company P43 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Harman Stove Company P43 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Harman Stove Company P43, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Harman Stove Company P43 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Harman Stove Company P43, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Harman Stove Company P43.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Harman Stove Company P43. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Harman Stove Company P43 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
