Manuel d'utilisation / d'entretien du produit 91523 du fabricant Harbor Freight Tools
Aller à la page of 21
GENERA T OR SET 6.5 HP - RECOIL ST AR T - 2600W/2800W RA TED Model 91523 OPERA TING INSTR UCTIONS ® 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W ebsite at: http://www .harborfreight.com Generators TO PREVENT SERIOUS INJUR Y , READ AND UNDERST AND ALL W ARNINGS AND INSTRUCTIONS BEFORE USE.
PR ODUCT SPECIFICA TIONS SKU 91523 P A GE 2 . I t em D escr i pt i on VAC El ect r i cal Requi r em ent s Curr ent O ut put : 110/ 120 Vol t s @ 20 A MP ’ s 60 Hz Cont i nuous/ Rated W at t age: 260.
SKU 91523 P A GE 3 GENERAL SAFETY RULES W ARNING! READ AND UNDERST AND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injur y . SA VE THESE INSTRUCTIONS WORK AREA 1. Keep your work area clean and well lit.
SKU 91523 P A GE 4 7. Do not expose Generator to rain or wet conditions. Water entering a generator will increase the risk of electric shock. 8. Do not abuse the P ower Cor d. K eep P ower Cords a w a y from heat, oil, sharp edges, or mo ving par ts. Replace dama g ed P ower Cor ds immediately .
SKU 91523 P A GE 5 GENERA T OR USE AND CARE 18. Make sure the P o wer Switch is in its “OFF” position and disconnect the spark plug wire before making any adjustments, changing accessories, or storing the generator . Such pre v entiv e saf ety measures reduce the risk of star ting the generator accidentally .
HEART P A CEMAKER PRECA UTION SPECIFIC PRODUCT W ARNINGS AND PRECA UTIONS SKU 91523 P A GE 6 W ARNING! P eople with pacemakers should consult their ph ysician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interf erence to or f ailure of the pacemaker .
SKU 91523 P A GE 7 9 . The suppor ting floor/ground surface should be le v el, and strong enough to safely hold the weight of the Generator . If the floor/g round surf ace is not le v el, strong cross members should be placed under the full length of the Generator F rame at its low side.
MECHANICAL PRECAUTIONS 1. AL W A YS mak e sure the Po wer Switch is in its “OFF” position. Disconnect the spark plug wire, and allow the Engine to completely cool before carrying out maintenance.
NOISE PRECAUTIONS 1. Prolonged exposure to noise levels above 85 dBA is hazardous to hearing. Alwa ys wear ANSI appro ved ear protection when operating or working around the Generator when it is running.
SKU 91523 P A GE 10 8. K eep all electrical equipment clean and dr y . Replace any wiring where the insu- lation is cracked, cut, abraded or otherwise degraded. Replace terminals that are worn, discolored, or corroded. Keep terminals clean and tight. 9.
5. Place the Generator as close as possible to the electrical tools and equipment being powered to reduce the length of extension cords. 6. If the Generator in located indoors the Engine exhaust must be ventilated to the outdoors using leak-proof, heat resistant, flexible, metal, flex tubing.
SKU 91523 P A GE 12 GROUND CONNECT OR (8) #6A WG GROUNDING WIRE (NOT INCLUDED) GROUNDING ROD (NOT INCLUDED) FIGURE B OIL DIPSTICK (65A) FIGURE C FUEL T ANK (30) FUEL T ANK CAP (33) FUEL GA UGE (34) EN.
SKU 91523 P A GE 13 3. Bef ore the first use , remo v e the Fuel T ank Cap (33) and fill the Fuel T ank (30) with nleaded gasoline. Then, replace the Fuel T ank Cap . Thereafter , check the Engine’ s Fuel Gauge (34) f or the amount of unleaded gasoline in the Fuel T ank.
SKU 91523 P A GE 14 FUEL T ANK (32) 5. T ur n the Engine P ower Switch (2) to its “ON” position. (See Figure F .) ENGINE POWER SWITCH (2) ON OFF FIGURE F 6. Hold the Start Handle (41A) loosely and pull it slowly several times to allow the gasoline to flow into the Engine’ s carburetor .
P o wering 120 V olt A C T ools And Equipment: 1. Prior to powering tools and equipment, make sure the Generator’ s rated v oltage, and amperage capacity (110/120V A C @ 20 AMPs) is adequate to supply all electrical loads that the unit will power .
SKU 91523 P AGE 16 7. NO TE: The Generator f eatures a 10 AMP DC Fuse (9) to protect the DC circuit in case of an overload. Should an overload occur the Fuse will burn out, causing the Generator to automatically shut down. In this case, refer to Step #1 in this section.
SKU 91523 P A GE 17 damaged electrical wir ing, and an y other condition that may aff ect its saf e opera- tion. If an Engine problem occurs, always have the Engine immediately checked out by a qualified service technician before further use. Do not use damaged equipment.
P ARTS LIST SKU 91523 P A GE 18 NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not available individually as replacement parts.
.
P ARTS LIST A Part # Description Q ty. Part # Description Qt y. 1A Muff ler 1 42A Sta r t ing Ca se Assy. 1 2A Cy linder Head Bolt 4 43A Spir a l Spring 1 3A Cy linder Head Cover Bolt 4 44A Starting W.
ASSEMBL Y DIA GRAM A NO TE: Some parts are listed and shown for illustration purposes only , and are not a vailab le individually as replacement parts. SKU 91523 P A GE 21 NO TE: When ordering parts from Parts List A and Assembly Diagram A include the suffix “A” behind the part number .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Harbor Freight Tools 91523 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Harbor Freight Tools 91523 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Harbor Freight Tools 91523, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Harbor Freight Tools 91523 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Harbor Freight Tools 91523, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Harbor Freight Tools 91523.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Harbor Freight Tools 91523. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Harbor Freight Tools 91523 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
