Manuel d'utilisation / d'entretien du produit 66630 du fabricant Harbor Freight Tools
Aller à la page of 22
10” HEA VY -DUTY 15 AMP T ABLE SA W 66630 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 2 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 3 DON’T FORCE TOOL. It will do the 7. job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool 8. or attachment to do a job for which it was not designed.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 4 or other part that is damaged should be properly repaired or replaced. DIRECTION OF FEED. Feed work 20. into a blade or cutter against the direction of rotation of the blade or cutter only .
SKU 66630 For technical questions, please call 1-800-444-3353. Page 5 controlled workpiece to lift up and out of the saw toward the operator . Kickback is usually a result of tool misuse and can be limited or avoided by following the precautions below: Fence must be completely parallel • to the saw blade.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 6 Essential Straight Push-stick Features and Functions Note: Straight style (traditional) stick shown. A dif- ferent stick design may be used if it properly protects against all hazards.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 7 When servicing use only identical 14. replacement parts. Only use safety equipment that has 15. been approved by an appropriate standards agency . Unapproved safety equipment may not provide adequate protection.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 8 reduce the risk of vibration-related injury: Anyone using vibrating tools regu- 1. larly or for an extended period should rst be examined by a doctor and then have regular medical check- ups to ensure medical problems are not being caused or worsened from use.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 9 stood, or if in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that 5. have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 10 SPECIFICA TIONS Electrical Requirements 120 V~ / 60 Hz / 15 A Motor No Load Speed 4800 RPM Blade Diameter 10” Arbor Diameter 5/.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 1 1 (109) and that the tabs are on the INSIDE slot of the Splitter . Use a framing square (not included) 8. to make sure the Saw Blade and Splitter assembly are square. If not square, loosen the Splitter Bracket and adjust until the Splitter is properly aligned with the Saw Blade.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 12 Blade Depth and Angle Adjustment The Blade (96) depth should be set 1. so that outer points of the Blade are 1/8” to 1/4” higher than the workpiece while the lowest points are below the workpiece.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 13 Aligning and Adjusting the Rip Fence (146) 1. W ARNING! A misaligned Fence can cause kickbacks and jams. T o reduce risk of injury , always maintain proper Fence alignment. The Rip Fence must be parallel with the Blade and T able grooves.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 14 edge of the square until it touches the marked tooth. Rotate the Blade and check the same 7. marked tooth at the rear of the T able Saw . If the front and rear measurements 8. are not identical, have a qualied ser - vice technician repair the T able Saw .
SKU 66630 For technical questions, please call 1-800-444-3353. Page 15 W ork Piece and Work Area Set Up Designate a work area that is clean 1. and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the power cord along a safe 2.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 16 When making a cut, use steady and 7. even pressure. Do not force cuts. Do not cut wet or warped lumber . 8. Hold the workpiece rmly with both 9. hands or use the included Push Stick.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 17 T o reduce possible injury should kickback occur , stand to side of the workpiece as it contacts the Blade. W ARNING! Do not stand in the line of cut. Once cut is made, turn off T able Saw .
SKU 66630 For technical questions, please call 1-800-444-3353. Page 18 MAINTENANCE AND SER VICING Proceduresnotspecically explained in this manual must be performed only by a qualiedtechnician.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 19 P ARTS LIST Part Description Qty . 1 Rubber feet 4 2 Bolt M6×25 5 3 Spring washer 8 4 Mat washer 13 5 Base 1 7 Bolt ST4.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 20 P ARTS LIST Part Description Qty . 109 T able 1 1 10 Bolt M6×25 1 111 Bolt M6×35 1 1 12 T able insert 1 1 13 Blade Guard 1 1 14.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 21 ASSEMBL Y DIAGRAM.
SKU 66630 For technical questions, please call 1-800-444-3353. Page 22 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Harbor Freight Tools 66630 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Harbor Freight Tools 66630 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Harbor Freight Tools 66630, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Harbor Freight Tools 66630 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Harbor Freight Tools 66630, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Harbor Freight Tools 66630.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Harbor Freight Tools 66630. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Harbor Freight Tools 66630 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
