Manuel d'utilisation / d'entretien du produit 46813 du fabricant Harbor Freight Tools
Aller à la page of 37
10" T ABLE SA W Model 46813 ASSEMBL Y AND OPERA TING INFORMA TION 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at http://www .
SPECIFICA TIONS T ABLE SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance, and cleaning procedures, parts list and assembly diagrams. Keep your invoice with this manual. Write the invoice number on the inside of the front cover .
4. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 5. USE EYE, HEARING, AND BREA THING PROTECTION.
SPECIFIC PRODUCT W ARNINGS AND PRECAUTIONS 1. GROUND THIS PRODUCT . The electrical power cord for this product is equipped with a grounded 3-Prong Plug. Never remove the grounding prong or modify the Plug in any way . Do not use adapter plugs with this product.
7. KEEP ALL GUARDS IN PLACE AND IN WORKING ORDER. 8. REMOVE ALL ADJUSTING WRENCHES FROM THE T ABLE SA W BEFORE TURNING IT ON. 9. A VOID UNINTENTIONAL ST ARTING. Make sure you are prepared to begin work before turning the Power Switch (part #8E) “ON”.
20. (Continued) T o avoid kickback, keep a firm grip on the workpiece at all times. Support overhanging work pieces; as the work piece is cut and weakens it will sag, causing a pinched Saw Blade. Push the workpiece slower than normal when cutting through knots, pressure treated and green lumber .
UNP ACKING When unpacking, check to make sure all parts shown on the Parts Lists (pages 27 through 29) are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible.
FIGURE C SKU 46813 P AGE 8 .
ASSEMBL Y INSTRUCTIONS NOTE: For additional references to the parts listed below , refer to the Assembly Diagrams on pages 29 through 37 of this manual. W ARNING! PRIOR T O PERFORMING ANY ASSEMBL Y PROCEDURES, MAKE SURE THE 10" T ABLE SA W IS DISCONNECTED FROM ITS ELECTRICAL POWER SOURCE.
3. Attach one Short Leg Brace (part #9B) to the lower mounting holes in two Legs (part #4B), using one Carriage Bolt (part #5B), one W asher (part #3B), and one Hex Nut (part #2B) for each Short Leg Brace. Repeat the assembly procedure for the remaining one Short Leg Brace and two Legs.
END BRACE (#6B) MOUNTING HOLES END BRACE (#6B) HEX NUT (#2B) W ASHER (#3B) BASE (#1G) HEX HEAD BOL T (#8B) BASE (#1G) FIGURE D T o Assemble The Extension T ables: 1. With the 10" T able Saw upside down, align the right and left side Extension T ables (part #5H) with the right and left ends of the T able Saw (with the beveled edges in front).
EXTENSION T ABLE (#5H) HEX HUT (#13H) HEX HEAD BOL T (#1 1H) W ASHER (#12H) 10” T ABLE SA W EXTENSION T ABLE (#5H) HEX NUT (#13H) SQUARE HEAD BOL T (#10H) EXTENSION T ABLE (#5H) FIGURE E FIGURE F W .
3. NOTE: The back side of the Front Rail (part #7H) has two slots. Slide the upper slot of the Front Rail over the Square Head Bolts (part #10H). (See Figures F , G, and Assy .
BASE (#1G) (RIGHT EDGE) EXTENSION T ABLE (#5H) 456789 SCALE (#6H) 7-1/8” MARK, RIGHT SCALE 3. Loosely attach a W asher (part #12H) and Hex Nut (part #13H) to each Square Head Bolt (part #10H). (See Figures I, J, and Assy . Diagram H.) FIGURE H 10” T ABLE SA W REAR RAIL (#3H) BASE (#1G) EXTENSION T ABLE (#5H) 2 -1 /2 ” FIGURE I 4.
10” T ABLE SA W/EXTENSION T ABLES (#5H) (REAR EDGES) REAR RAIL (#3H) SLOT SQUARE HEAD BOL T (#10H) W ASHER (#12H) HEX NUT (#13H) FIGURE J 5. Wrench tighten all five Square Head Bolts (part #10H). (See Figures I, J, and Assy . Diagram H.) T o Attach The Rip Fence And Miter Gauge: 1.
RIP FENCE (#10C) LOCK BLOCK (#7C) REAR RAIL (#3H) SA W T ABLE FIGURE K SCALE INDICA TOR (#20C) RIP FENCE (#10C) FRONT RAIL (#7H) FINE ADJUSTMENT KNOB (#30C) SA W T ABLE (#17H) RIP FENCE HANDLE (#37C) FIGURE L T o Attach The Power Switch: 1. Insert two Semi-Circle Head Screws (part #2E) from the rear of the Switch Plate (part #3E).
T o Assemble And Attach The Bevel And Height Handles T o The Base: 1. Insert one Screw (part #6G) each through a Bevel Handle and Height Handle (part #5G). T ighten each Screw into a Hand Wheel Assembly (part #4G). Then, attach an End Cap (part #7G) to each of the two Handles.
3. Secure the Motor Bracket (part #7F) to the Motor Mounting Plate (part #50-I), using four Hex Head Bolts (part #9-I), eight W ashers (part #52-I), four Lock W ashers (part #1-I), and four Hex Nuts (part #51-I). (See Figure N, and Assy . Diagrams F , and I.
2. Secure the Belt Guard (parts #1F , #4F) to the Motor (part #7F), using four Flat W ashers (part #3F) and four Hex Nuts (part #2F). (See Figures N, O, and Assy . Diagram F .) OUTER BEL T GUARD (#1F) MOTOR PULLEY (#5F) FLA T WASHER (#3F) HEX NUT (#2F) INNER BEL T GUARD (#4F) FIGURE O T o Attach The V-Belt: 1.
3. Push the Motor (part #7F), with its attached Belt Guard (parts #1F , #4F), forward and place the V-Belt (part #40-I) on the Motor Pulley (part #5F). (See Figure P , and Assy . Diagrams F , and I.) 4. T urn the Height Handle clockwise until it stops.
OUTER BLADE W ASHER (#15-I) ARBOR SHAFT (#13-I) BLADE NUT (#16-I) 10” SA W BLADE (#14-I) FIGURE R 3. Reach into the Saw Blade opening and remove the Blade Nut (part #16-I)) and Outer Blade W asher (part #15-I). (See Figure R, and Assy . Diagram I.) 4.
6. Once the 10" Saw Blade (part #14-I) is secured onto the Arbor Shaft (part #13-I), replace the Throat Plate (part #15H) and tighten the Flat Head Screw (part #16H) back in place. (See Figure Q, and Assy . Diagram H.) T o Attach The Blade Guard Assembly: 1.
OPERA TING INSTRUCTIONS T o Raise And Lower The 10" Saw Blade: 1. When cutting, the top edge of the Saw Blade (part #14-I) should rise about 1/4” above the top edge of the workpiece. 2. T o raise the height of the 10" Saw Blade (part #14-I), unlock the Bevel Lock (part #19-I).
3. T o adjust the bevel of the 10" Saw Blade (part #14-I), unlock the Bevel Lock (part #19-I). Next, move the Bevel Handle (part #5G) to the right or left until the desired bevel of the 10" Saw Blade is shown by the Bevel Scale (part #10G). Then, re-lock the Bevel Lock.
2. Before each use, inspect the general condition of the 10" T able Saw . Inspect the Power Switch (part #8E), Power Plug and Cord Assembly (part #8F), and extension cord (if used) for damage.
' .
8 = $ 8 = $ + .
P ARTS LIST SKU 46813 P AGE 28 8 = $ 8 = $ .
8 = $ 8 = $ 0 0 .
ASSEMBL Y DIAGRAM B NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 30.
ASSEMBL Y DIAGRAM C NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 31.
ASSEMBL Y DIAGRAM D NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 32.
ASSEMBL Y DIAGRAM E NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 33.
ASSEMBL Y DIAGRAM F NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 34.
ASSEMBL Y DIAGRAM G NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 35.
ASSEMBL Y DIAGRAM H NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 36.
ASSEMBL Y DIAGRAM I NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 46813 P AGE 37.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Harbor Freight Tools 46813 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Harbor Freight Tools 46813 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Harbor Freight Tools 46813, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Harbor Freight Tools 46813 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Harbor Freight Tools 46813, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Harbor Freight Tools 46813.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Harbor Freight Tools 46813. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Harbor Freight Tools 46813 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
