Manuel d'utilisation / d'entretien du produit 05154 du fabricant Harbor Freight Tools
Aller à la page of 20
SANDER - 4” BEL T & 6” DISC Model 05154 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.com Cop yr ight 2004 by Harbor F reight T ools ® . All rights reser ved.
PR ODUCT SPECIFICA TIONS GENERAL SAFETY RULES W ARNING! READ AND UNDERST AND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury . SA VE THESE INSTRUCTIONS W ORK AREA 1. Keep your work area clean and well lit.
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4.
11. Dress properl y . Do not wear loose clothing or je welr y . Contain long hair . K eep your hair , clothing, and gloves a way fr om moving parts. Loose clothes, je welr y , or long hair can be caught in moving par ts. 12. A v oid accidental star ting.
22. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that ma y affect the tool’ s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 23. Use only accessories that are recommended by the manufacturer for your model.
3. Y our tool must be plugged into an appropriate outlet, proper ly installed and grounded in accordance with all codes and ordinances . The plug and outlet should look like those in the f ollowing illustration. (See Figure A.) FIGURE A SKU 05154 P A GE 6 DOUBLE INSULA TED T OOLS: T OOLS WITH TW O PR ONG PLUGS 1.
SKU 05154 P AGE 7 serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
SKU 05154 P A GE 8 SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V olts Alternating Current Amperes No Load Revolutions per Minute (RPM) no xxxx/min. A V ~ FIGURE D SPECIFIC SAFETY RULES 1. Maintain a safe working environment.
9. Store idle equipment. When not in use, tools and equipment should be stored in a dr y location to inhibit rust. Alwa ys lock up tools and equipment, and k eep out of reach of children. 10. Do not use this product if under the influence of alcohol or drugs.
21. Allow the Sanding Disc (11) and Sanding Belt (45) to spin up to full speed before f eeding a workpiece into them. When tur ning off the Sander , allow the Sanding Disc and Sanding Belt to slow down and stop on their own. Do not press against the Disc or Belt to stop them.
SKU 05154 P AGE 11 27. W ARNING! The war nings, precautions, and instructions discussed in this manual cannot cov er all possible conditions and situations that ma y occur . The operator must understand that common sense and caution are factors which cannot be built into this product, b ut must be supplied by the operator .
T o Install A Sanding Disc: 1. W ARNING! Prior to performing an y assembly pr ocedures, make sure the Power Switch (30) is in its “OFF” position and the Power Cord (29) of the Sander is unplugged from its electrical outlet. 2. Check to mak e sure the Disc (11) is free of dir t, oil, and other debr is .
SKU 05154 P AGE 13 FIGURE H LOCK SCREW (15) WORK T ABLE (13) ANGLE PLA TE (14) T o Adjust The Angle Of The Miter Guide: 1. The angle of the Miter Guide (21) may be adjusted to the right 0 to 45 degrees and to the left 0 to 45 degrees. (See Figure I.) 2.
SKU 05154 P AGE 14 T o Adjust For V er tical Sanding: 1. Slightly loosen the Lock Screw (20). (See Figure J.) 2. Raise the Belt F rame ver tically to the desired position. Then, retighten the Lock Screw (20) to lock the Belt Frame in place. (See Figure J.
6. Once the sanding procedure is completed, remove the workpiece from the Sand- ing Belt (45). T ur n the P ow er Switch (30) to its “OFF” position, and unplug the machine from its electrical outlet. (See Figure K.) WORKPIECE POWER SWITCH (30) WORK SUPPORT (33) T o P erf orm V er tical Sanding With The Sanding Belt: 1.
SKU 05154 P A GE 16 8. Once the sanding procedure is completed, remove the workpiece from the Sand- ing Belt (45). T ur n the P ow er Switch (30) to its “OFF” position, and unplug the machine from its electrical outlet.
SKU 05154 P A GE 17 7. Hold the workpiece firmly with one hand and the Miter Guide (21) with the other hand. Gradually push the workpiece into the Sanding Disc (12), allowing the Sanding Disc to cut without being forced. (See Figure M.) FIGURE M MITER GUIDE (21) 8.
5. When storing, make sure to store the Sander in a safe, clean, and dry location. PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ARTS LIST AND ASSEMBL Y DIAGRAM IN THIS MANUAL AS A REFERENCE T OOL ONL Y .
SKU 05154 P AGE 19 P ARTS LIST NO TE: Some par ts are listed and sho wn f or illustration purposes only , and are not available individually as replacement parts.
SKU 05154 P A GE 20 ASSEMBL Y DIA GRAM & WIRING SCHEMA TIC NO TE: Some parts are listed and sho wn for illustration purposes onl y , and are not available individually as replacement parts.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Harbor Freight Tools 05154 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Harbor Freight Tools 05154 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Harbor Freight Tools 05154, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Harbor Freight Tools 05154 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Harbor Freight Tools 05154, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Harbor Freight Tools 05154.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Harbor Freight Tools 05154. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Harbor Freight Tools 05154 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
