Manuel d'utilisation / d'entretien du produit 705 Series 100 du fabricant A.O. Smith
Aller à la page of 40
PRINTED 0209 186965-001 Design information for single and multiple unit installations for residential, commercial, recircula- tion and storage tank systems.
2 Certifications .................................................................................. 3 Water Quality and Scale ................................................................ 8 Pump Sizing for Circulation ..............................
3 Certified to applicable U.S. standards for appliances using gas or other petroleum fuel. Certified to applicable Canadian standards for appliances using gas or other petroleum fuel. Certified by the Uniform Plumbing Code (UPC) Certified by National Sanitation Foundation (NSF), www.
Consumer Information The on-demand water heaters must be installed according to all local and state codes or, in the absence of local and state codes, the “National Fuel Gas Code”, ANSI Z223.
In addition to using the lowest possible temperature setting that satisfies your hot water needs, a means such as a mixing valve, should be used at hot water taps used by these people or at the water heater. Mixing valves are available at plumbing supply or hardware stores.
Closed System/Thermal Expansion CAUTION - PROPERTY DAMAGE HAZARD As water is heated, it expands (thermal expan- sion). In a closed system, the volume of water will grow. As the volume of water grows, there will be a corresponding increase in water pres- sure due to thermal expansion.
Temperature and Pressure Relief Valve For protection against excessive pressures and temperatures, a temperature and pressure relief valve must be installed in the opening on the on-demand storage tank.
8 W a ter Quality and Scale A complete water analysis and an unde rstandi ng of system requirements are needed to protect the on-demand water heaters and water heating systems from scale. Water analysis shows whether water is hard or soft. Hard water, unless treated, will cause scaling or liming of the heat exchanger.
9 Pump Sizing for Circulation 1. Use the chart below or one appropriate for your con ditions to determine the heat loss in the length of the hot water supply and return piping. For example, 100 ft of 1-1/2 in bare copper tubing results in a heat loss of 5300 Btu/h.
10 T ank W a ter Heaters in a Circulation Loop The following applies when using a tank water heater (gas or electric) to provide heat for a circulation loop. Drawing H-1-RP is an example. The heat output of the tank must be equal to or greater t han the calculated circulation loop heat loss.
The following applies when using on-demand water heaters to recover a storage tank. Drawing H-1-TC is an example. On-Demand water heaters have a pressure loss which must be considered in the system design. Reference the pressure loss curve for the heater m odel being used to determine the pump size for the desired recovery rate.
12 Pressure Loss (psi) Water Flow (gpm) 0. 0 5. 0 10. 0 15. 0 20. 0 25. 0 30. 0 35. 0 40. 0 45. 0 01 234 56 789 1 0 1 1 0. 0 10. 0 20. 0 30. 0 40. 0 50.
13 Pressure Loss (psi) Water Flow (gpm) Pressure Loss (ft head) Figure “5” 0 5 10 15 20 25 30 35 40 45 0123456789 1 0 1 1 0 10 20 30 40 50 60 70 80 90 100 705 505 305 Pressure Loss Curves 200/201 .
Domestic Hot W ater - S tandard Installation 1 On-Demand W ater Heater Preferred Piping Installation Drawing Number: Drawing Date: H-1 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Domestic Hot W ater - S tandard Installation 2 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-2 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Domestic Hot W ater - S tandard Installation 3 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-3 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Domestic Hot W ater - S tandard Installation 4 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-4 September 07, 2008 Pr i ma ry Hot W ater Supply Line Cold W ater.
Domestic Hot W ater - S tandard Installation 5 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-5 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Domestic Hot W ater - S tandard Installation 6 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-6 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Drawing Number: Drawing Date: H-1-E September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-E September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-3-E September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-6-E September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-1-RP September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-1-RO September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-RP September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-RO September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-3-RP September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-6-RP September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-1-T September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-1-TC September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-T September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-TC September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-3-T September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-3-TC September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-6-T September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-6-TC September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: MP-01 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
39 Notes.
• 500 T ennessee Waltz Parkway • Ashland, TN 37015 •.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté A.O. Smith 705 Series 100 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du A.O. Smith 705 Series 100 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation A.O. Smith 705 Series 100, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le A.O. Smith 705 Series 100 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le A.O. Smith 705 Series 100, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du A.O. Smith 705 Series 100.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le A.O. Smith 705 Series 100. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei A.O. Smith 705 Series 100 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
