Manuel d'utilisation / d'entretien du produit PA200AV du fabricant A-link
Aller à la page of 33
P A200A V(b) Ethernet Powerline Adaptor User Manual Single Pack or T win Pack Ethernet Powerline Adaptor i.
FCC Radiation Norm This equipment has b een tested and found to comply with limit s for a Class B dig ital device pursu ant to 47 CFR, Part 2 and Part 15 of the Fede ral Communicati on Commission (FCC) rules. Operati on is subject to the following T wo conditions: 1.
CAUTION! The Federal Communication Commission warns the user that chang es or modifications to the unit not expressly approved by the p arty responsible for compliance could void the user’ s authority to operate the equipment.
Ethernet Powerline Adaptor iv Chapter 1 Intr oduction ..................................................................................................................... 1 1.1 Featur es ...............................................................
Chapter 1 Introduction Congra tulations on your p urchase of this outsta nding Ethernet Powerline Adaptor . This device is a 200Mbps Po werline Ethernet Adaptor which transforms your house’ s existing electri cal wiring into a ubiquitous networking inf rastructure.
Ethernet Powerline Adaptor 2 1.1 Features Powerline AV y High speed dat a transfer rate up to 200Mbp s y HomePlug A V standard compliant y Works with AC input of 100V ~ 240V y Plug-and-Play (PnP) .
Ethernet Powerline Adaptor 3 1.2 Packet Contents The 200Mbps Ethernet Po werline Adaptor package cont ains the following items: One Ethernet Powerline Adaptor or T wo for T win pack One CA T -.
Chapter 2 Connecting Mechanism 2.1 Introduction The Ethernet Powerline Adaptor support up to 200Mbps dat a rate. With this high speed connection rate, this Ethernet Powerline Adaptor allows you to setup a high speed home network by using you r home existing electrical wiring.
2.1 LED Indicator The LED indicator displ ays information about the device’s status. Label St atus Description ON Another powerline port is detected on the sam e powerline network OFF Did not detect.
2.2 Physical Interface There are two physical interfaces on this Ethernet Powerli ne Adaptor . Interface Description Ethernet One 10/100Mbp s Ethernet port connected to PC LAN card or broad band device. Power Plug Power Plug connected to any 100V ~ 240V AC power socket.
2.3 Hardware Connection – Computer For those computers you wish to be networked by Ethernet Powerline Adaptor , each of the computers must be properly connected with an Ethernet Powerl ine Adaptor through an Ethernet (RJ-45) cable. Following are the step s to properly connect the Ethernet Powerline Adaptor to your computer: 1.
2.4 Hardware Connection – Internet This section describes how to co nnect the Ether net Powerline Adaptor into your existing ADS L broadband conne ction via ADSL Ethernet port. Follow the p r ocedures describe below to connect the Ethernet Powerline Adaptor to your ADSL broadb and connection: 1.
Chapter 3 Inst alling Management Utility Please verify that no other Ethernet Powerline Ad aptor or any Encryption Management Utilities are installed before installing the provided software. If other Powerline Utilities are in stalled, uninstall them and restart your personal comp uter befor e installing this provided software.
S tep 2: The program install ation process will carry out and copy all the necessary files to your system. Ethernet Powerline Adaptor 10.
Ethernet Powerline Adaptor 11.
S tep 3: After the installation, a sh ortcut to the “Power Packet Utility” application icon is provided on the windows desktop. Ethernet Powerline Adaptor 12.
Chapter 4 Using The Management Utility After you’d successfully installed the Ethern et Powerline Adaptor hardware and Managem ent Utility software, you can setup or configure t he device s according to your need.
4.1 Main The Main tab shows all the Ethernet Powerli ne Adaptor that are logically connected to the current computer where the Mana gement Utility is running. ; Local Device(s) on your computer: This shows all local Ethernet Po werline Adaptor found connected to the compute r’s LAN card.
Ethernet Powerline Adaptor 15 ; Autoscan: Shows the scanning status (Default is “ON” ). Device Name: Shows th e default device name. One may redefine or cha nge the name by clicking on the name and editing in place or by clicking the “Rename” button.
4.1.1 Rename This Management Utility allows you to change the na me of the listed Ethernet Powerline Adaptor. Click and select the Ethernet Powerline Adapt or you wi sh to change from the list, then click on the “Rename” tab and editing-in-place to cha nge the name.
4.1.2 Enter Password T o set or change your Ethernet Powerline Adaptor’s password, click a nd select the Ethernet Powerline Adaptor you wish to change from the list, then click on the “Enter Password” tab, the following screen display. Enter your Password (Take note to the password format) and click “OK” after setup.
4.1.3 Add Device The following dialog box pop-up wh en clicking the “Add” button under Main configuration homepag e. The dialog box allows you to enter both the selected device’s nam e and password.
4.2 QOS The second t abbed window , labeled ‘QoS’ for Quality of Service, is sh own in Figure. QoS requirement s are diff erent for various dat a types such as streaming vide o or music, voice and raw data. T o provide higher QoS for streaming dat a, priority levels can be set using t ags at the beginning of dat a frames.
Ethernet Powerline Adaptor 20 The ‘Default CAP’ group al lows for default priority ma pping of p ackets that do not have a VLA N or TOS bit (or if these are disabled).
4.3 Privacy The Privacy configuration page provides a means for managin g the local network and providing additional security for the logical network and also to sele ct the device s that has to be included in the network.
Ethernet Powerline Adaptor 22 ; Set Local Device Only: Click this tab to change the network name of the local Ethern et Powerline Adaptor device only. All Ethernet Powerline Adaptor devices seen o n t.
4.4 Diagnostics The Diagnostics homepage shows the System Information and Remote Dev ice History of all remote devices seen over a period of time wh ich are only readable. Click on the “Diagn ostics” tab and the following screen display. The Diagnostics information displayed can be saved to a text file.
Ethernet Powerline Adaptor 24 The Lower Panel contains a history of all remote Ethernet Powerline Adapto r devices seen on the computer over a certain period of time. All devices th at were on the powerline n etwork are listed here along with a few other parameters.
4.5 About The About homepage show the Management Utility software version. ; AutoScan: When enabled (Pla ce a check), the M anagement Utility will automatically scan for Ethernet Powerline Adapt or devices on the loca l network every few seconds and updated the scanning information on the Main configuration h omepage.
Advance Feature: How to Use the Push buttons sh buttons Pair( Secure with 128 bits-AES) The Powerline A V standard uses 128-bit AES (Advanced Encryption S t andard) t o safely transmit data between powerline adapter s. For the powerline adapt ers to communicate with each othe r they all need to use the same Network Membership Key (NM K).
Join an existing Powerline AV Network ： Step 1. Press and hold the Pair button on Powerline a daptor C for more than 10 seconds until both the Powerline and Power LED are off, then release t he button and the Power LED will start blinking. S tep 2. Press the Pair button of Powerline adaptor B for 2 seconds.
Appendix A: T roubleshooting Guide The Troubleshooting Guide provide s answers to common problems regardi ng the Ethernet Powerline Adaptor. 1. The Power LED does not light up. Ans. Check the following: 1. Make sure that the Ethernet Powerli ne A daptor is properly plugged into a power outlet.
Copyright The content s of this publication may not be reproduced in any part or as a whole , stored, transcribed in an information retrieval system, translat ed into any langu age, or transmitted in any form or by any mean s, mechanical, magneti c, electronic, optical, photocopying, manual, or othe rwise, without the prior written permission.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté A-link PA200AV c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du A-link PA200AV - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation A-link PA200AV, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le A-link PA200AV va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le A-link PA200AV, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du A-link PA200AV.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le A-link PA200AV. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei A-link PA200AV ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
