Manuel d'utilisation / d'entretien du produit ZIF36N RH du fabricant GE Monogram
Aller à la page of 40
GE Monogram ® 36" Refrigerators and 36" Freezers Custom Options Guide and Installation Instructions With Custom Pas ifimenstions.
CAUTION Before you begin – Read these instructions completely and carefully . IMPORT ANT – Save these instructions for local inspector’ s use. IMPORT ANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer – Be sure to leave these instructions with the Consumer .
3 Design Information 36" Refrigerators, Freezers Flush or Semi-Flush Enclosure Installations Side Panel Requirements: • Side panels are not required whenever the refrigerator is installed into an enclosure or between pantry and oven cabinets. • Side panels are required whenever the sides of the refrigerator are exposed.
4 For a complete food storage center , install a Monogram Freezer and Refrigerator side by side. Order ZUG75 Unified Grille Panel Kit for one continuous 3/4" panel. • Electrical and water locations must be located as shown for either type of installation.
5 Installation At End-of-Run Frameless Cabinets NOTE: 1/2" thick side panels shown. Side panels can be any thickness. Add side panel thickness to outside trim width, (36 ” or 72" for two models) to calculate the rough-in dimension. The leading (front) edge must be finished to match surrounding cabinetry .
6 T rim kit descriptions ZGC2 – Provides 1/4" grille panel frame side pieces for 83-1/2" and 84-1/2" installation heights. The supplied grille panel frame is factory set for 84". ZKHR1 – Provides the necessary framework to install a custom handle, of your choice , onto a 1/4" thick panel.
7 ZIR36N Refrigerator ZIF36N Freezer Design Information Designed to be installed flush or semi-flush with surrounding cabinetry . Cutout dimensions, clearances and side panel sizes are determined by the many installation options available. Side panels must be used whenever the sides of the refrigerator will be exposed.
8 Custom Door Panel Dimensions Using Standard T rim 1/4" thick panels or Panels secured to 1/4" thick backing ZIR36N Refrigerator ZIF36N Freezer • 1/4" Panel: Cut panels to size. • Custom handle with 1/4" door panel requires T rim kits ZKHR1 or ZKHRSS1 for tubular stainless steel handles.
9 ZIR36N Refrigerator ZIF36N Freezer • The ZKTR36LH (or ZKTR36RH) trim kit provides for the installation of 3/4" thick custom door and grille panels, using the supplied handle.
10 ZIR36N Refrigerator ZIF36N Freezer • The ZKTR36LH (or ZKTR36RH) trim kit installed together with a ZKHTR1 custom handle kit provides for the installation of 3/4" thick custom door and grille panels with a custom handle of your choice. Order ZKHTRSS1 for a tubular stainless steel handle.
23 5/16" 84" 2 5/16" 24 3/4" 84" 3 3/4" 23 9/16" 84" 2 9/16" T rim 11 1/4" Side Panels Insert end of side panel into trim. Use stick-on hook and loop fastener strips to secure the panel to the refrigerator .
12 T ools Required • T insnips to cut banding • Stepladder • 1-1/4" open-end wrench • Bucket • Level • Appliance Hand T ruck • T ubing cutter • 7/16" open-end wrench • #2 P.
13 • Remove outer carton. – Carefully cut banding at the top and bottom. • Slide out back corner posts (2). • Slide carton off top of cabinet. NOTE: IT IS NOT NECESSARY TO LA Y CABINET DOWN IN ORDER TO REMOVE SKID! • The unit is secured to the skid with 4 slotted tie-down straps.
14 Step 2 Install Water Line • Install optional water filter in the water line near the refrigerator . A water filter is recommended in areas where water supply contains sand or particles. Installation instructions are packed with the filter . • A cold water supply is required for automatic icemaker operation.
15 Step 3 Install Side Panels • Side panels are not required when the refrigerator or freezer is installed into an enclosure. Skip this step if you are installing into an enclosure.
16 Step 5 Level Refrigerator or Freezer All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by wheels. • Adjust rear wheels beneath the product to just barely touch the 2x4 block. • T urn the 7/16" hex nut located above the front wheels.
17 Step 9 Check Power • Check to make sure power is on by opening the door to see if interior lights are on. If you are using a 3/4" thick custom panel, SKIP THIS STEP . See Dimensions and Specifications for grille panel sizes. Order ZKTR36LH or ZKTR36RH and follow the installation instructions packed with the kit.
18 Step 13 Start Icemaker • A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and tighten screws. IMPORT ANT : The vented toekick must remain unobstructed for proper air circulation and operation.
19 This kit provides optional side trim pieces for the original grille panel frame to fit 83-1/2" and 84-1/2" installation heights. T o change grille panel size: • Determine the installation height by measuring the enclosure from the floor to the underside of soffit.
20 T ools and materials required: • #2 Phillips screwdriver • Drill and appropriate bits • Custom door panel • Custom Handle • Safety glasses Parts List: A.
21 Step 2 Locate handle position • Determine the desired location of the custom handle and mark centerlines of the screw holes. • Drill 1/16" pilot hole through the panel until it starts into the aluminum extrusion. This will mark the matching location for drilling the clearance hole when assembling the handle, panel and extrusion.
22 Right hand door swing models are illustrated in these instructions. Follow these instructions for left hand models. T ools and materials required: • #2 Phillips screwdriver • Drill and appropriate bits • Custom door panels • Putty knife • Safety glasses • 7/16" wrench Parts List A.
23 Step 2 Install 3/4" trim Step 3 Apply panel support brackets • Attach the new 3/4" trim pieces on the top, hinge side and bottom using original screws. • Position support bracket on the back side of the custom panel, 14-5/16" from the hinge side.
24 Step 5 Install handles Step 6 Adjust grille panel height • Install new door handle using original screws. • Secure the grille panel support to the back side of the 3/4" custom panel with #6 screws. • Be sure the lip of the support is over the top of the wood panel.
25 Step 8 Install grille panel • Install four of the six larger undercut screw so that the top of the screws are 1/16" from the surface of the support. • Attach the assembled panel to the grille opening by inserting the four protruding screws into the brackets on each side.
26 3/4" custom door panel must be routed to accommodate these door handle extrusions. Rout the panel as illustrated, 1/4" deep, and 1-13/16" wide on the handle side. Refer to installation instructions for ZKTR36LH or ZKTR36RH trim kit for 3/4" custom panels: • Follow Step 1 to remove the standard aluminum trim.
27 • Place the prepared 3/4" custom door panel on the bottom trim with support bracket tabs inserted into trim slots. • Push the panel back against the steel door , making sure the panel is flush with the hinge side trim. • Secure the panel to the trim temporarily by driving 2 screws through the backside of the trim at the top.
28 Step 4 Mount assembled panel • Place assembled panel onto the bottom trim with support bracket tabs inserted into slots. • Push the panel back against the steel door with handle extrusion flush to handle side of the door . • Open door fully to stop.
29 Step 1 Remove handle Right hand door swing models are illustrated in these instructions. Follow these instructions for left hand models. NOTE: It is best that 2 people install this kit.
30 Step 2 Match handle extrusions to handle FOR CUSTOM WOOD PA N E L S See Step 2A for Stainless Steel panels • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling.
31 Step 3 Install standoffs onto handles • Place a handle standoff onto each attachment post along the handle. Position the set screw hole on the standoff to point to the floor . • Install set screws into the bottom of each standoff, using the Allen wrench provided.
32 Raised Panel on 1/4" Thick Backing: A raised panel design secured to a 1/4" thick backing (screwed or glued) can be used with this handle kit. • Cut the 1/4" thick panels to size. • Fabricate the raised panel to allow 1-1/4" clearance from the hinge side of the panel to avoid striking adjacent cabinetry .
33 Before you begin: Right hand door swing models are illustrated in these instructions. Follow these instructions for left hand models. This kit provides for the installation of a T ubular Stainless Steel handle on a 3/4" thick decorator door panel.
34 Step 1 Match Handle Extrusion to Panel • Cut a piece of corrugated to use as a pad to protect the panel finish. Additional material may be required to protect flooring when drilling. • Place custom panel on the pad, appearance side down. • Select handle extrusion for your model, left or right side extrusion.
35 This kit provides for the installation of a 3/4" thick custom grille panel to span the combined width of a side by side installation. Use this kit in combination with 3/4" custom panel kits, ZKTR36LH and ZKTR36RH.
36 • Cut a 2"x4" block, 71" long. Secure the 2"x4" to the 4 mounting brackets provided using #12 or #14 wood screws. • Secure the brackets with wood block to the back wall so that it is 84" (or your installation height) from the finished floor .
Stud Spacer Block Refrigerator Cabinet Door 37 Step 5 Install Center T rim Strip • Open doors fully . • Starting at the top, press trim strip over inside case trims of both products. • Continue pressing trim until you reach the bottom of the case trims.
38 Step 7 Install Grille Base Cover • Open doors fully . • Install the double width grille base cover by slipping the notched ends over the hinges. • Place wire fence over the grill base cover (textured side out). Drive original wire fence screws through the fence, the grille base cover and into the frame.
39 Step 9 Install Soffit Ve n t T o p • Separate the top and hinge side trim pieces by removing side screws. Discard top piece, retain screws. • Install one end piece to unified top piece with 2 original screws. • Slip end of rubber dust gasket into end of top unified piece and slide trim towards the center .
Pub. No. 49-60055-3 Dwg. No. 197D2785P001 12-03 JR 65160-01 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local ser vice in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté GE Monogram ZIF36N RH c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du GE Monogram ZIF36N RH - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation GE Monogram ZIF36N RH, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le GE Monogram ZIF36N RH va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le GE Monogram ZIF36N RH, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du GE Monogram ZIF36N RH.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le GE Monogram ZIF36N RH. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei GE Monogram ZIF36N RH ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
