Manuel d'utilisation / d'entretien du produit DH2000 du fabricant GE
Aller à la page of 44
Door-type High T emperature Dishwasher Installation/Operation Manual with Service Re placement Parts 2674 N. Service Road, Jordan Station Ontario, Canada L0R 1S0 905/562-4195 Fax: 905/562-4618 T oll-free: 800/ 263-5798 3765 Champion Boulevard Winston-Salem, NC 27105 336/661-1556 Fax: 336/661-1660 T oll-free: 800/ 858-4477 Issue Date: 6.
COPYRIGHT © 2012 All rights reserved Printed in the USA For future reference, record your dishwasher information in the box below . Model Number__________________________ Serial Number_______________.
http://www .championindustries.com/canada/register REGISTER YOUR PRODUCT ONLINE Make sure you are connected to the internet then enter the address below .
PR ODUCT REGISTRA TION BY FA X (336) 661-1660 in the USA 1-(800) 204-0109 in Canada IMPORTANT IMPORTANT Model Serial # Date of Installation: Company Name: T elephone #: ( ) --- Contact: Address: Addre.
i Revision History Revision Revised Serial Number Revision Date Pages Effectivity Description 6.12.09 All D09037592 Released First Edition Revision History The Revision History can contain part number changes, new instructions, or information that was not available at print time.
ii Limited Warranty LIMITED W ARRANTY Champion Industries Inc. (herein referred to as Champion), 3765 Champion Blvd., Winston-Salem, North Carolina 27105, and P .O. Box 301, 2674 N. Service Road, Jordan Station, Canada, L0R 1S0, warrants machines, and parts, as set out below .
iii Revision History ........................................................................................................... i Limited Warranty .......................................................................................................
iv Model Description Model Description 2000 Series High temperature hot water sanitizing dishwasher with built-in 40-70°F/22-82°C rise booster heater .
1 NOTE: The installation of your dishwasher must be performed by qualified service personnel. Problems due to improper installation are not covered by the W arranty . 1. Inspect the outside of the dishwasher carton for signs of damage. 2. Remove the carton and inspect the dishwasher for damage.
2 Installation Converting Straight-through Operation to Corner Operation Dishwashers are shipped from the factory for Straight-through operation. Refer to the diagrams below and on the next page to convert a Straight-through operation machine to a Corner operation machine.
3 Installation Converting Straight-through Operation to Corner Operation wall wall A A T o convert track guides and door-lift for corner operation: 1. Remove the rack guide (A); save the fasteners. Move (A) and re-attach as shown in the illustration at right.
4 Installation Electrical Connections A TTENTION A qualified electrician must connect the main incoming power to the dishwasher in accordance with all local codes and regulations or in the absence of local codes in accordance with the National Electrical Code.
5 A standard 3-phase operation dishwasher can be converted for 1-phase operation with the installation of a jumper wire on the main terminal and rewiring of the wash tank and booster tank heaters. A jumper wire, jumper bars and a new data plate are stowed on top of the wash tank heater junction box.
6 Installation Hot W ater Connection NOTE: Plumbing connections must comply with all national and/or local plumbing and sanitary codes. The hot water connection is located at the lower left-rear side of the dishwasher . A 3/4" line strainer and pressure regulating valve (PRV) were installed at the factory .
7 Installation NOTE: Consult a qualified chemical supplier for chemical supplies and chemical dispensing equipment. Chemical Dispenser Provisions Detergent Rinse-aid V ent Fan Control 1. A vent fan control signal is provided on a terminal block located inside the top-mounted control cabinet.
8 Initial Start-up Installation Check List 1. Remove any protective lm from dishwasher . Check the interior for foreign material. 2. Make sure that the dishwasher is permanently located. 3. Make sure that all utility connections are complete. 4. Make sure that the chemical supply containers are full.
9 Operation Normal Operation Mode Door Safety Switch Power Switch W ash T emperature Gauge Final Rinse T emperature Gauge Pressure Gauge In-cycle Light Follow the instructions below to operate the dishwasher in a Normal W ash Mode. A Rinse Sentry feature holds the dishwasher in a wash mode if the booster heater temperature is below 180ºF/82ºC.
10 Operation Normal Operation Mode (continued) Final Rinse Pressure W ash T emperature Final Rinse T emperature WINSTON-SALEM,NC CHAMPION INDUSTRIES, INC. 10 0 30 20 PSI 60 50 40 0 20 40 60 80 100 120 140 160 180 200 220 100 80 60 40 20 0 20 40 60 80 100 120 140 160 180 200 220 100 80 60 40 20 20-25 PSI 150°F/66°C 180-195°F 82-91°C 12.
1 1 Operation Rinse Sentry Operation Mode The nal rinse water temperature must be a minimum of 180ºF/82ºC during the final rinse cycle to ensure that all wares are sanitized.
12 After Each Meal Period or every 8 Hours of Operation. 1. Press the lighted power switch to the OFF position. The power switch light will go out and the automatic drain cycle will operate for 10-minutes. 2. Flush the interior of the machine with fresh water .
13 Cleaning Cleaning and Maintenance At the End of the Day 1. Perform Steps 1-10 on the previous page. 2. Remove the upper and lower rinse and wash spray arms. The spray arms are interchangeable. 3. Unscrew the upper and lower rinse arm spindles (A). Remove the rinse arm assemblies 4.
14 Cleaning and Maintenance Minerals accumulate on the interior surfaces of the dishwasher . The deposits have a white haze and, in cases of heavy accumulation, may appear as a granular solid. The generic name for mineral deposits is lime. The removal of lime deposits is called de-liming.
15 Cleaning and Maintenance Maintenance Daily Maintenance 1. Check all of the wash arm and rinse arm spray jets and clean as necessary . 2. Make sure the water supply is on and that the drain is not clogged. 3. Check the temperature gauges and/or displays to ensure that they are operating.
16 T roubleshooting Follow the troubleshooting guide below in the event that your dishwasher does not operate as expected. Perform the basic checks below before calling an authorized service agent: 1. Make sure that the main water supply is turned on.
17 Service Replacement Parts Service Replacement Parts Illustrations Page W ash Pump/Motor Assembly ................................................................................................................................ 18 Booster Assembly ..
18 Wash Pump/Motor Assembly 12 11 10 14 13 9 8 7 6 5 4 1 2 3.
19 Item Part Description Qty . No. No. 1 1 14134 SLINGER, W A TER 1 2 1 14135 NUT 9 3 1 14136 SCREW 9 4 1 14137 BACKPLA TE, PUMP 1 5 1 14138 GASKET , PUMP 1 6 1 14139 SEAL, PUMP 1 7 1 14140 W ASHER 1 .
20 Booster Assembly 6 7 7 8 4 5 1 3 14 16 17 15 13 12 18 19 20 21 22 10 11 9 2 7.
21 Item Part Description Qty . No. No. 1 100184 NIPPLE, 3/4" NPT X CLOSE BRASS 2 2 100210 PLUG, 1/8" SST 1 3 100571 UNION, 3/4" NPT BRASS 1 4 102444 ELBOW , STREET 3/4" NPT X 90° BRASS 2 5 107550 V AL VE, PRESSURE REG.
22 Control Panel Assembly 2 4 8 1 6 48 32 47 33 35 25 20 41 30 36 49 23 51 42 39 34 40 50 44 45 9 10 18 11 43 46 27 28 37 22 31 21 26 5.
23 Item Part Description Qty . No. No. Control Panel Assembly 1 100003 NUT , HEX PLAIN 1/4-20 SST 8 2 100007 SCREW , TRUSS HD. 10-32 X 3/8" SST 5 3 100100 SCREW , ROUND HD.
24 Wash and Rinse Spray Arm Assemblies 37 27 28 29 33 35 34 3 16 15 24 2 3 17 14 1 4 5 8 7 6 9 8 32 19 10 12 11 23 20 18 26 18 21 37 25 31 30 13 22.
25 Item Part Description Qty . No. No. 1 100135 GAUGE, PRESSURE 0-60 PSI 1 2 100156 LOCKNUT , 3/4" NPT BRASS 1 3 100171 BUSHING, RED. F ACE 3/4" X 1/2" BRASS 3 4 100599 CROSS, 3/4" NPT BRASS 1 5 100736 BOL T , HEX HD. 1/4-20 X 3/4" SST 2 6 102388 BUSHING, RED 1/2" NPT X 1/4" NPT BRASS 1 7 102525 TEE, RED.
26 Hood and Door Assembly 14 11 25 12 4 2 17 15 13 9 7 16 21 11 10 10 20 20 4 6 24 18 5 1 3 4 8 3 6 26 22 24 19 23 4 21 27 27 28 29 29 29 13.
27 Item Part Description Qty . No. No. Hood and Door Assembly 1 100002 BOL T , HEX HD., 1/4-20 X 1-3/8" SST 2 2 100738 BOL T , HEX HD., 1/4-20 X 1" SST 4 3 106014 NUT , HEX ACORN PLAIN, 1/4-.
28 T rack Assemby 5 6 7 9 3 4 1 2 8 11 10.
29 Item Part Description Qty . No. No. T rack Assembly 1 100003 HEX PLAIN NUT , 1/4-20 SST 6 2 100073 SCREW , TRUSS HD., 1/4-20 X 1/2" SST 6 3 100754 SCREW , FLA T HD.
30 Wash T ank Heat, Drain, Screens, Hoses 3 4 10 10 8 5 9 2 1 1 3 11 12 25 13 14 15 16 16 17 18 19 20 21 22 23 24 1 1 6 7.
31 Item Part Description Qty . No. No. Wash T ank Heat, Drain, Screens, Hoses 1 107340 CLAMP , HOSE 4 2 1 14745 HOSE, DISCHARGE 1 3 104203 CLAMP , HOSE 2 4 1 14467 HOSE, SUCTION 1 5 332543 COVER, JUNC.
32 32 Item Part Description Qty . No. No. Dish Racks, Line Strainer , PRV 1 2 3 4.
33 Item Part Description Qty . No. No. Dish Racks, Line Strainer , PRV 1 101273 DISH RACK, FLA T -BOTTOM AR 2 101285 DISH RACK, PEG AR 3 1 10768 STRAINER, LINE 3/4" BRONZE 1 4 107550 V AL VE, PRES.
34 T imer Chart, Electrical Schematic Illustrations Page T imer Chart ................................................................................................................................ 35 Electrical Schematic ............................
35 Timer Chart TIME CY CLE - DH/MD2000 DWG. 114470-0/B 3/10/09 L.B. 60 10 02 0 40 30 50 70 90 80 100 100 80 90 70 50 30 40 20 01 0 60 60 10 02 0 40 30 50 70 90 80 100 100 80 90 70 50 30 40 20 01 0 60 .
36 Electrical Schematic BY DA TE DESCRIPTION RE V. B RE V. The Dishwashing Machine Specialists RE V. DESCRIPTION DA TE BY CUSTOMER TO SUPPL Y RA TED VOL TA GE/PHASE/Hz, AS SPECIFIED PER ORDER, TO DISCONNECT SWITCH. ALL POWER SUPPLIED TO EACH CONNE CT ION POINT MUST CO MP LY WITH ALL LO CAL ELEC TRIC CO DES.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté GE DH2000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du GE DH2000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation GE DH2000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le GE DH2000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le GE DH2000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du GE DH2000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le GE DH2000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei GE DH2000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
