Manuel d'utilisation / d'entretien du produit CP7317RS du fabricant Altinex
Aller à la page of 16
CONTROLLERS CP7317RS RS – 232 CONTROLLER USER’S GUIDE MANUAL PART NO. 400-0017-003 PRODUCT REVISION: 0.
CONTROLLERS 1 INTRODUCTION Thank you for purchasing the CP7317RS RS-232 Controller. We are sure you will find it a reliable and useful product. Superior performance for the right price backed by solid technical and customer support is what we have to offer.
CONTROLLERS 2 PRECAUTIONS / SAFETY WARNINGS 1 Please read this manual carefully before using your CP7317RS RS-232 Controller. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your CP7317RS and to prevent fire and shock hazard.
CONTROLLERS 3 ABOUT CP7317RS - RS-232 CONTROLLER 2 The CP7317RS RS-232 Controller is designed to provide expanded capabilities to any control system. The CP7317RS is designed to accept RS- 232 commands from a control device and output those commands as relay contacts or digital high or low.
CONTROLLERS 4 CP7317RS DESCRIPTION 4 CP7317RS FEATURES 4.1 RS-232 PORT This port (located next to the power outlet) is a fully programmable, bi-directional, and full duplex port that has the ability to operate at any baud rate up to 9600. The general standard on transmission is 8 bits, no parity, and 1 stop bit.
CONTROLLERS 5 The following table shows the pin-outs on the connector corresponding to the following I/O port pin numbers. Connector Pin No. 1 2 3 4 5 6 7 8 9 I/O Port Pin No. 1 3 5 7 9 Ground 2 4 6 8 There are 4 ports with 8 I/O pins and one ground pin, #5 on each port.
CONTROLLERS 6 4.7 PROGRAMING COM MANDS The commands below are used for presetting the default status of the unit. Note: AFTER USING THE PROGRAMMING COMMANDS LISTED BELOW, THE CP7317RS SHOULD BE POWERED OFF AND THEN ON. [SETIp,b,n] This command sets individual pins of each I/O port to input or output status.
CONTROLLERS 7 b This letter defines the status of a pin, while its position in a string number corresponds to the pin number on the I/O Port of the CP7317RS . For example b 4 represents the status of Pin 4 on the I/O connector. The valid pins on I/O port are from 1 to 9 except 5.
CONTROLLERS 8 FIGURE 6: Input/Output Port Pin Configuration n This letter designates the status of the pin as either high or low during “Power up” of the unit. when n = 1 the pin is set as high when n = 0 the pin is set as low Example: Set pin 1 of port 3 as low during POWER ON.
CONTROLLERS 9 n This letter designates the status of the relay during “Power up”. n=1 relay is open n=0 relay is closed Example: Set relay 6 of port 2 to be open at power up.
CONTROLLERS 10 Bit No. Connector Pin No. 7 4 8 9 n Data that defines the status of the pin n=1 or n=0. [SETDp, b 1 b 6 b 2 b 7 b 3 b 8 b 4 b 9 ] SET all pins on the particular I/O port of the unit. This command defines if I/O port pins will be high or low.
CONTROLLERS 11 [READDp] Read Digital status of a particular port. The feedback is in the following format [10011100] 1 is for high 0 is for low. The feedback provides status of all pins. Left most character is a bit pin number 1. p Port number, this is an ASCII character from 1 to 4 that matches the port number on the back of the CP7317RS .
CONTROLLERS 12 4.10.1. MEMORY 1 I/O port/memory is A Sub-Register address is from 00 to 255 Sub-Register definitions 00 This location should be set to FFh i f memory initialization is required. During the power up sequence this location is checked for software revision.
CONTROLLERS 13 33 Power up status of relays on port 2,3,4. If bit is set to 0 then relay will be closed on power up. If bit is set to 1 then relay will be open on power up. 34 Left bracket for beginning command code. Factory set to “[“. 35 Right bracket for ending command code.
CONTROLLERS 14 08 00-07 locations for return code for port 1 pin 2 for transition from 0 to 1. This return code should include any necessary brackets. .
CONTROLLERS 15 ALTINEX POLICY 5 5.1 LIMITED WARRANTY Altinex warrants that its products and cables are free from defects in materials under normal use and service. This warranty is limited to repairing at company’s factory any part or parts of the product, which upon company’s examination shall disclose to be, thus defective.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Altinex CP7317RS c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Altinex CP7317RS - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Altinex CP7317RS, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Altinex CP7317RS va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Altinex CP7317RS, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Altinex CP7317RS.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Altinex CP7317RS. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Altinex CP7317RS ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
