Manuel d'utilisation / d'entretien du produit PRN608-S du fabricant Fujitsu
Aller à la page of 53
PRN608 - S 28 - 03 - 2003 Page 1 - 1 of 53 User Manual Thermal printer controller PRN608 - S FOR FUJITSU THERMAL PRINTERS FTP608 SERIES.
PRN608 - S 28 - 03 - 2003 Page 1 - 2 of 53 VERSION HISTORY Version Date Init Status Description 1.0 030328 BB Released First release Copyright 1999 - 2003 by I/F - COM A/S. All rights reserved. I/F - COM A/S has prepared this manual for use by I/F - COM A/S’ customers.
PRN608 - S 28 - 03 - 2003 Page 1 - 3 of 53 completely excluded. Please assume that such failure may occur before using this printer. We would urge that t hese specifications should be thoroughly understood and the printer used safely in your company or associated organisation.
PRN608 - S 28 - 03 - 2003 Page 1 - 4 of 53 1 SYSTEM DESCRIPTION ............................................................................................ 1 - 7 2 INSTALLATION .........................................................................
PRN608 - S 28 - 03 - 2003 Page 1 - 5 of 53 3.8.18 Italic off .......................................................................................................... 3 - 24 3.8.19 Italic on ...........................................................
PRN608 - S 28 - 03 - 2003 Page 1 - 6 of 53 7.2.1 Escape sequences, overview. .......................................................................... 7 - 45 7.3 APS COMPATIBLE COMMAND S ET ( OPTIONAL ) ...............................................
PRN608 - S 28 - 03 - 2003 Page 2 - 7 of 53 1 SYSTEM DESCRIPTION This reference manual describes the specifications, functions, and operating procedures for the PRN608 - S Interface Board. The PRN608 - S is an interface board for the FTP608 series printer mechanisms.
PRN608 - S 28 - 03 - 2003 Page 2 - 8 of 53 thermal printer connector on the PCB. 1 Mounting hole is grounded. See drawing for more details. (a) To connect or remove the connector, always turn off the power in advance. If the connector is connected or removed while t he power to the printer is on, errors may occur.
PRN608 - S 28 - 03 - 2003 Page 2 - 9 of 53 even when setup menus can be set to higher speed. In order to obtain higher speed you need to install 3 rd part utility program on PC. Please visit www.if - com.com for furt her information. 1. Turn off power 2.
PRN608 - S 28 - 03 - 2003 Page 2 - 10 of 53 1. Input key (Default) 2. LED out put 3. Label detect 4. Black mark detection 5. Paper near end function j. Key 2 function 1. Input key 2. LED output 3. Label detect 4. Black mark detection 5. Paper near end function k.
PRN608 - S 28 - 03 - 2003 Page 2 - 11 of 53 i. 0 (Default) ii. 1 iii. 2 iv. 3 v. 4 vi. 5 vii. 6 viii. 7 ix. 8 x. 9 r. Bu rn strobe light i. - 1 ii. - 2 iii. - 3 iv. - 4 v. - 5 vi. - 6 vii. - 7 viii. - 8 ix. - 9 Settings will be effective upon turn off and on.
PRN608 - S 28 - 03 - 2003 Page 2 - 12 of 53 When the error is ca ncelled, X on is output. 2.6.1 Serial data transfer The PRN608 - Stransfers various data other than the X on and X off codes which are output when controlling X on and X off .
PRN608 - S 28 - 03 - 2003 Page 2 - 13 of 53 Error processing when receiving serial data The PRN608 - S receives and checks serial data according to the transmission conditions. When the PRN608 - S has received one byte of data without errors, the data is stored in the input buffer.
PRN608 - S 28 - 03 - 2003 Page 2 - 14 of 53 d ot line so that the number does not exceed the specified maximum number of activated dots. The PRN608 - S determines logical blocks each time it prints a single dot line.
PRN608 - S 28 - 03 - 2003 Page 2 - 15 of 53 Electrolytic corrosion may significantly shorten the life of the thermal head. Thermal paper ordinarily contains electrolytic material to prevent sheets from sticking to each other due to static electricity.
PRN608 - S 28 - 03 - 2003 Page 2 - 16 of 53 Specifications Default settings Interface Ser ial RS232C, USB or IRDA Data format serial 115.200 baud, 8 data bit, none parity, 1 stop bit, hardware handshake. Baud rate can be changed by software. Data format USB USB Printer class specification.
PRN608 - S 28 - 03 - 2003 Page 3 - 17 of 53 3 Function 3.1 General Notice, when data is sent from the external equipment to th e printer controller, all data has to be sent as binary file. If data is being sent as a character file, and some data in the file is equal to EOF, the rest will not be received.
PRN608 - S 28 - 03 - 2003 Page 3 - 18 of 53 3.5 Firmware upgrade. If firmware needs to be changed, alternative f irmware can be downloaded. Please contact I/F - COM for firmware upgrade or changes. The steps to download an alternative firmware in DOS are the following.
PRN608 - S 28 - 03 - 2003 Page 3 - 19 of 53 3.7 Character design The following figures describes the design of different types of characters (small): 3.7.1 Normal Character. 3.7.2 Low Character 3.7.3 Underline When underline characters are printed the last line in the character matrix will be marked.
PRN608 - S 28 - 03 - 2003 Page 3 - 20 of 53 3.7.4 Bold When bold characters are printed the character is or with itself shifted right. 3.7.5 Reverse When reverse characters are printed the character matrix will be negated.
PRN608 - S 28 - 03 - 2003 Page 3 - 21 of 53 3.8 I/F - COM simple command set. The following commands are use when communicating with the printer controller. All other commands is ignored 3.8.1 Small Font [Name] Small Font (8x12) [Format] ASCII NUL Hex 00 Decimal 0 [Description] Chooses small font from the current print position.
PRN608 - S 28 - 03 - 2003 Page 3 - 22 of 53 [Description] Chooses wide font from the current print position. 3.8.6 High Font [Name] High Font (16 x56) [Format] ASCII ENQ Hex 05 Decimal 5 [Description] Chooses high font from the current print position.
PRN608 - S 28 - 03 - 2003 Page 3 - 23 of 53 barcode 39, and the ‘*’ can only be used as start and end character. If the barcode length exceeds the paper size the last barcode character will not be written as barcode. In that case the barcode cannot be read because the last character will not be ‘*’ 3.
PRN608 - S 28 - 03 - 2003 Page 3 - 24 of 53 Hex 11 Decimal 17 [Description] This command will switch on underline printing 3.8.16 Bold off [Name] Bold off [Format] ASCII DC2 Hex 12 Decimal 18 [Description] This command will switch off bold printing 3.
PRN608 - S 28 - 03 - 2003 Page 3 - 25 of 53 3.8.21 Request Software version [Name] Request softwa re version [Format] ASCII ETB Hex 17 Decimal 23 [Description] When the printer controller receives this byte the software version will be transmitted. This command can be treated even if buffer is full.
PRN608 - S 28 - 03 - 2003 Page 3 - 26 of 53 [Description] When the printer controller receives this byte the digital value of the head temperature will be transmitted.
PRN608 - S 28 - 03 - 2003 Page 3 - 27 of 53 3.8.29 Stop sending automatic status [Name] Stop se nding automatic status [Format] ASCII ESC b Hex 1B 62 Decimal 27 98 [Description] When this command is sent then it will turn off transmitting status. 3.8.
PRN608 - S 28 - 03 - 2003 Page 3 - 28 of 53 3.8.33 Change dot size [Name] Change dot size [Format] ASCII ESC f n Hex 1B 66 n Decimal 27 102 n [Description] If n = 0x01, then the board is set to FTP628MCLxxx. If n = 0x02 then is it set to FTP638MCLxxx.
PRN608 - S 28 - 03 - 2003 Page 3 - 29 of 53 3.8.37 Feed Paper [Name] Feed Paper [Format] ASCII GS n Hex 1D n Decimal 29 n [Range] n: [ - 128;127] [Description] When the printer controller receives this command the paper will be fed n - dot lines. If the value is negative a reverse form feed will be made.
PRN608 - S 28 - 03 - 2003 Page 3 - 30 of 53 3.8.40 Bar code height setting. [Name] Bar code height setting [Format] ASCII ESC h n Hex 1 B 68 n Decimal 27 104 n [Range] 1<=n<=255 [Default] n=60 [Description] Parameter n specifies the height of a bar code in dots.
PRN608 - S 28 - 03 - 2003 Page 3 - 31 of 53 The following table shows the value between data (d) and barcode. Code128 barcode table ‘d’ A B C ‘d’ A B C 0 Space Space 0 52 T T 52 1 ! ! 1 53 U U.
PRN608 - S 28 - 03 - 2003 Page 3 - 32 of 53 40 H H 40 92 FS | 92 41 I I 41 93 GS } 93 42 J J 42 94 RS ~ 94 43 K K 43 95 US DEL 95 44 L L 44 96 FNC3 FNC3 96 45 M M 45 97 FNC2 FNC2 97 46 N N 46 98 SHIFT.
PRN608 - S 28 - 03 - 2003 Page 3 - 33 of 53 PAPER OFFSET (default 2mm) This value is the length between Black Mark and start of printing. Value must be between 2 mm. and Page length – 2mm. BLACKMARK LENGTH (default 15mm). This is the length of the Black Marks.
PRN608 - S 28 - 03 - 2003 Page 3 - 34 of 53 [Description] When the printer controller receives a byte that is – Y to – 2 (Decimal 256 - Y to 254) the following data is compressed data. The number of compressed graphic bytes is the negative value. This me ans: If Y = - 10 (Decimal 246) the next 10 bytes is compressed data.
PRN608 - S 28 - 03 - 2003 Page 3 - 35 of 53 ETB Request software version CAN Request status EM Request analogue voltage SUB Request temperature GS+n Feed paper RS+n Burn compensate US+d1.
PRN608 - S 28 - 03 - 2003 Page 4 - 36 of 53 4 Maintenance 4.1 Daily use Printer and interface board must be switch off while in idle mode. 4.2 Store/Transport The product has to be stored under ES D safe conditions, and to be packed safely during transportation.
PRN608 - S 28 - 03 - 2003 Page 5 - 37 of 53 5 Specifications 5.1 Electrical Data Voltage: 6 - 8,5VDC Current: Maximum head current: Numbers of active dots * Vhead 150+/ - 15% Maximum motor current: 1000mA Power up sequen ce: max. 10 msec. 10 – 90% Voltage applied Power down sequence: max.
PRN608 - S 28 - 03 - 2003 Page 5 - 38 of 53 5.5 Temperature Test Temperature shock: (no voltage applied) - 28°C to +100°C at 1 sec. 100 times: no damage.
PRN608 - S 28 - 03 - 2003 Page 6 - 39 of 53 6 Connector Pin Assignment 6.1.1 Thermal Hea d connector FTP628MCL05x/1xx/35x Connector CN1: 3800 - 30P - T - S Mating connector part number: TBA Pin Functi.
PRN608 - S 28 - 03 - 2003 Page 6 - 40 of 53 8 DI 23 VH 9 /LAT 24 NC 10 CLK 25 SW 11 /ST6/ /AOE1 26 GND 12 /ST5 27 /MB 13 /ST4 28 MB 14 +5V 29 /MA 15 /ST3 30 MA 6.1.3 IRDA connector IRDA connector CN3: B4B - ZR Matin g connector part number: TBA Pin 1 2 3 4 Function +5V TX RX GND 6.
PRN608 - S 28 - 03 - 2003 Page 6 - 41 of 53 The paper near end status, can be seen on the LED on the au x connector, it can be reading through the status command, and if a driver is used, then it can .
PRN608 - S 28 - 03 - 2003 Page 6 - 42 of 53 TBA Pin 1 2 3 4 Function N.C. USB - USB+ GND 6.1.8 AUX connector Connector type CN11: 53324 - 0510 Mating connector TBA Pi n 1 2 3 4 5 Function GND Vcoil, Max 24V Coil, max 1A Anode Cathode Using output as cash drawer solenoid time must be set.
PRN608 - S 28 - 03 - 2003 Page 6 - 43 of 53 Mating connector part number: FC10AGN (Taitek) Pin Function Pin Function 1 NC 2 DSR 3 TX 4 CTS 5 RX 6 RTS 7 DTR 8 NC 9 GND 10 NC 6.
PRN608 - S 28 - 03 - 2003 Page 7 - 44 of 53 7 Appendix 7.1 Seiko compatible command set (optional) 7.1.1 Escape sequences, overview. CR CR Carriage Return ESC+ ‘ J ’ +n Print and Feed Forward ESC+.
PRN608 - S 28 - 03 - 2003 Page 7 - 45 of 53 DC2+ ‘ Q ’ Option Font Clear DC3+ ‘ A ’ Ruler Line Buffer A DC3+ ‘ B ’ Ruler Line Buffer B DC3+ ‘ V ’ + Image Data Ruler Line Image DC3+ ‘.
PRN608 - S 28 - 03 - 2003 Page 7 - 46 of 53 ESC J+n Printing and minimum - pitch - unit paper feed ESC K+n Backward paper feed ESC R+n Internationa l character specification ESC c+1+n Internal process.
PRN608 - S 28 - 03 - 2003 Page 7 - 47 of 53 Decimal 10 [Description] When the printer controller receives this byte the text data in the buffer will be printed.
PRN608 - S 28 - 03 - 2003 Page 7 - 48 of 53 7.3 APS compatible command set (optional) 7.3.1 Escape sequences, overview. GS / n Set printing speed / Maximum peak curr ent GS D n Set print Intensity ESC.
PRN608 - S 28 - 03 - 2003 Page 7 - 49 of 53 Format: <1Dh> <2Fh> <n> Comments: n=1 to 32: (Default n=5) Software programmable consumption (Dynamic division). The maximum number of black dots which are simultaneously heated is (n+1) x 8.
PRN608 - S 28 - 03 - 2003 Page 7 - 50 of 53 7.4 ESC/POS compatible command set (optional) 7.4.1 Escape sequences, overview. ESC c 4 Select Paper Near End Sensors to stop printing HT Horizontal Tab LF .
PRN608 - S 28 - 03 - 2003 Page 7 - 51 of 53 ESC i Partial cut ESC p m t1 t2 Cash drawer Output ESC t n Select character Code table ESC u n Transmit peripheral device status ESC v Transmit paper sensor.
PRN608 - S 28 - 03 - 2003 Page 7 - 52 of 53 7.5 Optional sensor descr iption Top view Bottom view Please note that distance from top of sensor to paper must be Min 0,5mm and Max 1,00mm PIN1 PIN2 PIN3.
PRN608 - S 28 - 03 - 2003 Page 7 - 53 of 53 Example showing how to connect PRS600 to AUX Input connector CN4 on PRN608 - S standard board . RED RED WHITE BLACK RED WHITE BLACK.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Fujitsu PRN608-S c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Fujitsu PRN608-S - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Fujitsu PRN608-S, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Fujitsu PRN608-S va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Fujitsu PRN608-S, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Fujitsu PRN608-S.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Fujitsu PRN608-S. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Fujitsu PRN608-S ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
