Manuel d'utilisation / d'entretien du produit AM/FM stereo du fabricant Ford
Aller à la page of 248
Introduction 4 Instrument Cluster 12 W arning and control lights 12 Gauges 15 Entertainment Systems 17 AM/FM stereo 17 AM/FM stereo cassette 19 AM/FM stereo with CD 21 AM/FM stereo with in-dash six CD.
Seating and Safety Restraints 75 Seating 75 Safety restraints 81 Air bags 91 Child restraints 95 Driving 1 1 1 Starting 111 Brakes 114 T ransmission operation 118 V ehicle loading 125 T railer towing .
Maintenance and Specifications 181 Engine compartment 182 Engine oil 184 Battery 187 Fuel information 195 Air filter(s) 210 T ire Information 212 Part numbers 225 Refill capacities 226 Lubricant specifications 231 Accessories 240 Index 243 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol.
SPECIAL NOTICES Emission warranty The New V ehicle Limited W arranty includes Bumper -to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance W arranties.
T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtainin.
Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the rec.
Notice to owners of natural gas fueled vehicles Before you drive your vehicle, be sure to read the Dedicated Natural Gas V ehicle supplement. This book contains important operation and maintenance information.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner ’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation .
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle ’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and ST ART , or by applying the parking brake when the ignition is turned to the ON position.
Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Check gage: Illuminates when any of the following conditions has occurred: • The engine coolant temperature is high. • The engine oil pressure is low .
GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “ H ” and “ C ” ). If it enters the red section, the engine is overheating.
T rip odometer: Registers the kilometers (miles) of individual journeys. Press the SELECT/RESET control once to switch from the odometer to the trip odometer . Press the control again to select T rip A and T rip B features. T o reset the trip, press and hold the control again until the trip reading is 0.
AM/FM STEREO (IF EQUIPPED) 1. Seek: Press / to find the next listenable station down/up the frequency band. 2. T une: Press / to manually adjust the radio frequency down/up.
5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 6. T one: Press TONE until the desired level — Bass, T reble, Fade appears on the display . T urn the volume control to raise/lower the levels, or to move the audio sound from the right to left or the front to back (if equipped).
AM/FM STEREO CASSETTE (IF EQUIPPED) 1. Balance: Press to shift sound to the left/right speakers. 2. Fade: Press to shift sound to the rear/front speakers. 3. CLK: T o set the hour , press and hold CLK. Then press SEEK to decrease or increase the hours.
4. T ape AMS: In tape mode, press and hold to activate Automatic Music Search (allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection). Then, press REW (for the beginning of the current selection) or FF (to advance to the next selection).
13. AM/FM: Press to choose a frequency band in radio mode. 14. Bass: Press / to decrease/increase the bass output. 15. T reble: Press / to decrease/increase the treble output. 16. EJ (Eject): Press to eject a tape. 17. Cassette door: Insert a cassette into the cassette door .
1. Balance: Press / to shift sound to the left/right speakers. 2. Fade: Press / to shift sound to the front/rear speakers. 3. SCN (Scan): Press to hear a brief sampling of all listenable stations or CD tracks. Press again to stop. 4. CLK: T o set the hour , press and hold CLK and press SEEK to decrease or increase the hours.
11. T une : In radio mode, press to move up or down the frequency band in individual increments. 12. Seek: Press and release SEEK / for previous/next strong station, selection or track. 13. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.
PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED) 1. Seek: Press and release SEEK / for previous/next strong station, or track of the current disc. 2. Rewind: Press and hold until the desired selection is reached. Fast forward: Press and hold until the desired selection is reached.
6. Bass: Press BASS; then press SEL / to decrease/increase the bass output. T reble: Press TREB; then press SEL / to decrease/increase the treble output. 7. Select: Use with Bass, T reble, Balance and Fade controls to adjust levels. Use with MENU to set the clock and RDS function on/off.
10. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 11. CD: Press to select CD mode. 12. AM/FM: Press to select AM/FM1/FM2 frequency band. In CD mode, press to begin radio play .
RADIO FREQUENCIES AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM - 530, 540 – 1700, 1710 kHz FM- 87.7, 87.9 – 107.7, 107.
Don ’ t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 12 cm (4.
T o operate the system: 1. Y our AutoVision 威 system is automatically activated when the vehicle ignition and the audio system are ON. Note: The VCP will not generate sound if the vehicle ’ s audio system isn ’ t turned on. 2. If a movie is desired, insert a VHS cassette into the VCP and the video should start playing.
Should you have any questions regarding your AutoVision 威 System, please feel free to call the toll free assistance hotline at 1 (877) 848 – 6434. Safety information Read all of the safety and operating instructions before operating the system and retain for future reference.
tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Humidity and moisture condensation Moisture in the air will condense in the VCP under extremely humid conditions or when moving from a cold place to a warm one. Moisture condensation on the tape playback head drum may damage the videocassette and/or drum.
AutoVision 姞 system Features • 2 – head hi-fi playback • AutoPlay feature • Digital auto tracking • Dual stereo headphone with electric volume control • Self docking connection for easy .
VCP controls 1. LED display The display lamp will light up in green when power is supplied to the videocassette player . 2. POWER key Press to toggle between ON/OFF . When the power is ON, other keys (PLA Y , FF , REW , STOP) will illuminate. 3. PLA Y key Press to playback a videocassette tape.
Remote control 1. POWER button Press to turn the videocassette player (VCP) ON or OFF . 2. ENCORE button Press to reverse the casssette for 5 seconds. Normal playback will then resume when in PLA YBACK mode. 3. STILL/ADV ANCE (frame advance button) Press to temporarily suspend playback.
7. PLA Y button Press to play the tape. 8. REW button Press to rewind the tape. 9. FF button Press to fast forward the tape. 10. STOP button Press to stop the tape. Battery replacement Batteries are supplied with the remote control unit. However , they are simply for operation check and will only work for a short time.
If you will not be using the remote control for a considerably long time, remove the batteries. AutoVision 姞 controls The AutoVision 威 controls allow the rear seat passengers to operate the radio, tape, CD or CD DJ(if equipped). Parental control Y our AutoVision 威 system allows you to have control over the rear seat controls.
Adjusting the volume This control allows the rear seat passengers to adjust the volume level of the audio system. Press the + control to increase the volume. Press the — control to decrease the volume. From the AutoVision 威 controls, the speaker volume cannot be set higher than the current volume radio setting.
Speakers ON/OFF mode W ith the speakers ON, you can adjust the audio output to all system speakers — front and rear together (headphones are disabled in this mode). The rear seat passengers can not raise the volume of the system above the level on the front radio bezel.
Memory preset control In radio mode, press the MEM (Memory) control successively to scroll through the memory presets in AM, FM1 or FM2. In CDDJ mode, press the MEM (Memory) control to select the next disc in the compact disc changer . Play will begin with the first track.
Flip-down screens The screens rotate down to view and up into the housing to store when not in use. Ensure that the screens are latched into the housing when being stored. 1. 6.4 ” (diagonal) color liquid crystal display (LCD) screen. 2. Screen housing.
Inserting/removing cassette Inserting cassette • Open the AutoVision 威 console cover . • Insert the videocassette into the cassette compartment. Inserting a videocassette into the VCP automatically turns the power ON (the indicator lamp will illuminate) and the tape will begin playback.
On-screen indicators Playback operation 1. Press the POWER control on the VCP . 2. Insert a videocassette into the VCP . 3. The videocassette should automatically begin playback, and the picture will appear within approximately nine seconds. 4. Press the STOP control to stop playback or press EJECT to remove the cassette.
Encore (on remote control) • Press the ENCORE control while in playback mode. The VCP will reverse to the previous five seconds of the selection and then operate at normal playback mode.
V ideo source selection The MEDIA control determines which video (VCP or Auxiliary input) is seen on the AutoVision 威 screen. When the vehicle ignition is ON and the system is not in VCP mode, the AutoVision 威 selects the Auxiliary input as the video source.
The following are some possible messages that may illuminate on your LED display and their meanings. Illuminates when there is a videocassette in the system during power off. Illuminates when there is a videocassette in the system during power on. Illuminates when a videocassette is ejected from the system.
Illuminates when the videocassette is in PLA Y mode. Illuminates when the videocassette is in REV (review) mode. Illuminates when the videocassette is in CUE mode.
• Patch cords with RCA style connectors These parts are available in your local electronics store or call toll free 1 (877) 848 – 6434 for assistance. Auxiliary jacks for home use 1. VIDEO OUT Connect this terminal to the VIDEO IN terminal of your display (LCD, TV).
HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
• Remove any snow , ice or leaves from the air intake area at the base of the windshield. T o aid in side window defogging/demisting in cold weather: 1.
HEADLAMP CONTROL • The first position turns on the parking, tail, license plate and side marker lamps. • The outer position turns on the headlamps. Battery saver The battery saver will turn off the courtesy lamps in 10 minutes if a door is left open and the key is not in the ignition.
Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does not activate with your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. TURN SIGNAL CONTROL • Push down to activate the left turn signal.
Front and rear courtesy/reading lamps The dome portion of the lamp, the center light, can be turned on when the headlamp control is rotated fully counterclockwise or when any door is opened. The reading lamp portion, the two outer lights, can only be toggled on and off at the lamp.
Replacing headlamp bulbs (aerodynamic) 1. Make sure headlamp switch is in the OFF position and open the hood. 2. Push each clip tab toward the engine compartment and lift upward to the stop position, then remove the headlamp assembly . 3. Disconnect the electrical connector from the bulb by pulling rearward.
Replacing headlamp bulbs (low series) 1. Make sure headlamp switch is in the OFF position and open the hood. 2. Remove the two headlamp screws and bezel from the headlamp housing. 3. Remove the four headlamp bulb retaining screws and the retaining ring.
Replacing high-mount brakelamp bulbs The interior cargo lamp (if equipped), on vehicles without a rear headliner , will have to be removed from under the high-mount brakelamp assembly located inside the vehicle. Then: 1. Remove the two screws from the high-mount brakelamp assembly and lift the lamp from the vehicle.
Replacing tail lamp/turn/backup lamp bulbs 1. T urn the headlamp switch to the OFF position and then remove the four screws and the lamp assembly from vehicle. 2. Rotate bulb socket counterclockwise and remove from lamp assembly . 3. Carefully pull the bulb straight out of the socket and push in the new bulb.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position.
1. Place V elcro hook onto side of aftermarket transmitter opposite of actuator control. 2. Place the transmitter into storage compartment, control down. 3. Place the provided height adaptors onto the back of the GARAGE control as needed. 4. Press the GARAGE control to activate the transmitter .
The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy . Adjustments may need to be made to the zone and calibration of the compass.
CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others ’ safety when using such equipment.
POWER WINDOWS (IF EQUIPPED) When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and hold the bottom part of the rocker switch to open the window .
T elescoping mirror The spotter mirror has a swivel that allows it to tilt up and down, and also to tilt left and right to increase side and rear visibility . Fold-away mirrors The mirrors can be manually folded forward or backwards for narrow spaces like driving through an automatic car wash or backing out of a garage with the trailer tow mirror .
SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a speed of 48 km/h (30 mph) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.
Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACCEL control until you get to the desired speed, then release the control. Y ou can also use the SET ACCEL control to operate the T ap-Up function.
Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle ’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer . Y ou should always carry a second key with you in a safe place in case you require it in an emergency . POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors.
Changes or modifications not expressly approved by the party responsible for compliance could void the user ’ s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 10 meters (33 feet).
Sounding a panic alarm Press to activate the alarm. Press the control again, or turn the ignition to the 1 (ACCESSORY) or 4 (ON) position to deactivate the alarm. Note: The panic alarm will only operate when the ignition is in the 2 (LOCK) or 3 (OFF) position.
Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming.
Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The illuminated entry system will turn off the interior lights i.
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat ’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Pull lever up to adjust seatback. Using the manual lumbar support The lumbar support control is located on the inboard side of the driver ’ s seat. T urn the lumbar support control clockwise to increase firmness. T urn the lumbar support control counterclockwise to increase softness.
Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Quick release captains chair (7 passenger second row only) T o remove the seat: 1.
Stow the tongue end of the detachable anchor . 2. Pull the seat latch handle, then pull the seat toward the right side of the vehicle to disengage four pins from the floor mount. 3. Remove the seat. T o install the seat: Check to see that the seat and seatback is latched securely in position.
REAR SEATS Accessing the 3rd, 4th and 5th row seats (if equipped) T o make access to the 4th and 5th row seats easier , attach the 3rd and 4th row passenger side seat belts to the trim panel by using the snaps attached to the seat belt webbing and the trim panel.
2. Pull the LH/RH seat latch handles, located under the seat, rearward to release the latch hook ends from the front strikers. 3. Move the seat rearward and lift the seats rear hooks away from the rear strikers prior to lifting the front hooks out from the front strikers.
SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o reduce the risk of injury , make sure children sit in the back seat where they can be properly restrained.
Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.
When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt.
After any vehicle collision, the safety belt systems at all outboard seating positions (except the driver position, which does not have this feature) must be checked by a qualified technician to verify that the automatic locking retractor feature for child seats is still functioning properly .
Front safety belt height adjustment Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, push the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place.
Shorten and fasten the belt when not in use. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If.
If... Then... The driver ’ s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off... The BeltMinder feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until safety belt is buckled.
Reasons given... Consider ... “ I was in a hurry ” Prime time for an accident. BeltMinder reminds us to take a few seconds to buckle up. “ Seat belts don ’ t work ” Safety belts, when used properly , reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks.
Deactivating/activating the BeltMinder feature Read step s1-5 thoroughly before proceeding with the deactivation/activation programming procedure. The BeltMinder feature can be deactivated/activated b.
will flash 4 times per second for 3 seconds, followed by 3 seconds with the light off, then followed by the airbag warning light flashing 4 times per second for 3 seconds again. 5. After receiving confirmation, the deactivation/activation procedure is complete.
AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly; there is a risk of injury from a deploying air bag.
The National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant ’ s chest and the driver air bag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.
Children and air bags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic.
Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Air bag readiness section in the Instrument Cluster chapter . Routine maintenance of the air bag is not required.
Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Do not attempt to service, repair , or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer . Children and safety belts If the child is the proper size, restrain the child in a safety seat.
Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the sea.
Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs. The shoulder belt should cross the chest, resting snugly on the center of the shoulder . The lap belt should rest low and snug across the hips, never up high across the stomach.
When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from).
Installing child safety seats with combination lap and shoulder belts 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. Never place a rear -facing child seat in front of an active air bag.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer ’ s instructions.
7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
Because the last row of seats is not equipped with either child tether or LA TCH anchors and is spaced closer to the row of seats in front, Do not use forward-facing or rear -facing child seats (other than belt-positioning boosters) in the last row . Air bags can kill or injure a child in a child seat.
3. Route the child safety seat tether strap over the back of the front right-hand passenger seat as shown. 4. Clip the tether strap hook to the seat pedestal to the location shown. 5. Adjust the front right hand passenger seat to the full rearward position.
6. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 7. T ighten the child safety seat tether strap according to the manufacturer ’ s instructions.
3. Clip the tether strap hook to the seat pedestal at the location shown. 4. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 5. T ighten the child safety seat tether strap according to the manufacturer ’ s instructions.
3. Clip the tether strap hook to the tether bracket mounted under rear rail of seat cushion frame. 4. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 5. T ighten the child safety seat tether strap according to the manufacturer ’ s instructions.
• Seven passenger wagon • Eight passenger wagon • T welve passenger wagon • Fifteen passenger wagon represents LA TCH anchors. represents tether strap anchors.
Never attach two LA TCH child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. The lower anchors for child seat installation are located at the rear section of the seat between the cushion and seat back.
STARTING Positions of the ignition 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel.
Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic.
• Make sure the gearshift is in P (Park). • T urn the key to 4 (ON) without turning the key to 5 (ST ART). Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver ’ s safety belt is fastened, the light may not illuminate.
Note: If the engine does not start within five seconds on the first try , turn the key to 3 (OFF), wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel.
keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking; this is normal and should be no reason for concern. ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates when the ignition is turned on.
The parking brake is not recommended to stop a moving vehicle. However , if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency . Since the parking brake applies only the rear brakes, the vehicle ’ s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.
V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity .
AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed.
Understanding the gearshift positions of the 4 – speed automatic transmission This vehicle is equipped with an adaptive T ransmission Shift Strategy .
N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. (Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four .
• Selecting 2 (Second) at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever . • W ill not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds.
Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur . Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur , or the engine may overheat.
D (Drive) without Overdrive D (Drive) without Overdrive can be activated by pressing the transmission control switch (TCS) on the end of the gearshift lever . • This position allows for all forward gears except overdrive. • The OFF lamp on the gearshift lever is illuminated.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially if the depth is not known. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars).
V EHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance.
Exceeding the Safety Certification Label axle weight rating limits could result in substandard vehicle handling, performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter .
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum Loaded T railer W eight - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) E-150 Regular V an (6700 GVWR) 4.6L 3.55 5216 (11500) 2903 (6400) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum Loaded T railer W eight - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) E-250 Regular V an (Crew) (8600 GVWR) 4.6L 4.10 4990 (11000) 2404 (5300) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum Loaded T railer W eight - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) E-350 Regular V an (Crew) (9500 GVWR) 5.4L 3.55 5443 (12000) 2767 (6100) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum Loaded T railer W eight - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) E-350 Regular W agon (8 – passenger) (8600 GVWR) 5.4L 3.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum Loaded T railer W eight - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) E-350 Extended W agon (15 – passenger) (9300 GVWR) 6.8L 3.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum Loaded T railer W eight - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) E-350 Chassis Cab (138 ” wheelbase, dual rear wheel) (10700 GVWR) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum Loaded T railer W eight - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) E-350 Stripped Chassis (138 ” wheelbase) (10000 GVWR) 5.
GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum Loaded T railer W eight - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) Maximum.
Safety chains Always connect the trailer ’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer ’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you.
• T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. • Anticipate stops and brake gradually . When descending long, steep downhill grades, always use a lower gear to provide engine braking to save wear on brakes.
Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water . Reconnect the wiring to the trailer after the trailer is removed from the water . When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper .
GETTING ROADSIDE ASSISTANCE T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers who require roadside assistance, call 1 – 800 – 665 – 2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount.
Except for commercial stripped chassis vehicles, this switch is located in the front passenger ’ s footwell, by the kick panel. On commercial stripped chassis vehicles, this switch is located on a bracket above the brake pedal. T o reset the switch: 1.
FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
T o remove a fuse use the fuse puller tool provided on the fuse panel cover . The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 15 A 4 .
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 6 10A Brake-shift interlock, Speed control (gasoline engine only) 7 10A Multi-function switch, T urn signals 8 30A Radi.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 24 — Not used 25 10A Left headlamp (low beam) 26 20A Cigar lighter , Diagnostics 27 5A Radio 28 — Not used 29 20A P.
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle ’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 3 10A* Daytime Running Lamps (DRL) module, A/C clutch 4 20A* Natural Gas V ehicle (NGV) tank solenoids (natural gas vehicle only).
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 23 10A* Alternator 24 20A* T railer tow running lamps and back-up lamp relays 25 — Not used 26 20A* T railer tow turn signals 2.
The relays are coded as follows: Relay location Description 1 Interior lamps 2 Open 3 Roof marker lamps 4 Battery saver Engine compartment relay module The engine compartment relay module is located i.
CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily . • gradually decrease the vehicle ’ s speed. • hold the steering wheel firmly . • slowly move to a safe place on the side of the road. The use of tire sealants may damage your tires.
• W et weather driving capability • All-Wheel Driving Capability (if applicable) • Load Leveling Adjustment (if applicable) When driving with the dissimilar spare tire/wheel additional caution s.
Tire change procedure Preparing to change the tire T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
• non-chassis cab vehicles: jack is located in the rear right-hand side of the cargo area. • E-350 chassis cab vehicles(if equipped): jack is strapped to a bracket behind the driver ’ s seat.
7. Use the tapered end of the lug nut wrench to unscrew wheel ornaments attached by retaining screws. Remove any wheel trim. Insert the tapered end of the lug nut wrench behind wheel covers or hubcaps and twist off. 8. Loosen the wheel nut by pulling up on the handle of the lug nut wrench about one-half turn (counterclockwise).
Rear axle jacking points - All models except E-350 Dual Rear Wheel (DR W) and E-450: Rear axle jacking points - E-350 Dual Rear Wheel (DR W) and E-450: Front axle jacking points: Place the jack under the pin on the front surface of the front axle. Do not place the jack under or on the steering linkage.
If your vehicle has single rear wheels, thread the lug nuts on the studs with the beveled face toward the wheel. If your vehicle has dual rear wheels, thread the two element swiveling lug nuts on the studs with the flange facing toward the wheel. 3. Use the lug nut wrench to screw the lug nut snugly against the wheel.
2. Slide the wheel partially under the vehicle and install the retainer through the wheel center . Pull on the cable to align the components at the end of the cable. 3. T urn the jack handle clockwise until the tire is raised to its stowed position underneath the vehicle.
On all two-piece flat wheel nuts, apply one drop of motor oil between the flat washer and the nut. Do not apply motor oil to the wheel nut threads or the wheel stud threads.
Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle ’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery .
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle ’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle ’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . Ford recommends your vehicle be towed with a wheel lift or flatbed.
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized Ford dealer for warranty repairs. While any Ford dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction.
Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, o.
In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law .
from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs T o have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form.
Making a decision Board members review all available information related to each complaint, including oral presentations, and arrive at a fair and impartial decision.
In the CAMV AP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes.
ORDERING ADDITIONAL OWNER ’ S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.
3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time) In the case of 1 or 2 above, the consumer must also notify th.
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail W ash (ZC-3 – A), which is available from your dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• Do not allow paint sealant to come in contact with the sliding door electrical contact switches. Paint sealant or other contaminants could interfere with the proper operation of the power locks or radio speakers. If necessary , clean the contacts with Motorcraft Bug and T ar Remover (ZC-42) to remove any sealant.
• Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaning the engine.
• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • W iper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly .
Do not use cleaning solvents, bleach or dye on the vehicle ’ s seatbelts, as these actions may weaken the belt webbing. LEATHER SEATS (IF EQUIPPED) Y our leather seating surfaces have a clear , protective coating over the leather . • T o clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11 – A).
Motorcraft Extra Strength Upholstery Cleaner (not available in Canada) (ZC-41) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Wheel and T ire Cleaner (ZC-37 – A) Motorcraft Dash and Vinyl.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service.
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located in the center top of the grill. 3. Lift the hood and secure it with the prop rod.
1. W indshield washer fluid reservoir 2. Engine oil filler cap 3. Automatic transmission fluid dipstick 4. Air filter assembly 5. Engine oil dipstick 6. Power steering fluid reservoir 7. Brake fluid reservoir 8. Engine coolant reservoir 9. Battery WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low .
W asher fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle ’ s paint finish, wiper blades or washer system. If you operate your vehicle in temperatures below 4.5 ° C (40 ° F), use washer fluid with antifreeze protection.
• If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage.
Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil. Only use oils “ Certified For Gasoline Engines ” by the American Petroleum Institute (API). T o protect your engine ’ s warranty use Motorcraft SAE 5W -20 or an equivalent 5W -20 oil meeting Ford specification WSS-M2C153 – H.
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates and only for frame mounted deep cycle auxiliary batteries, check the battery electrolyte level.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “ cold fill level ” or within the “ cold fill range ” as listed on the engine coolant reservoir (depending upon application).
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap.
Used engine coolant should be disposed of in an appropriate manner . Follow your community ’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle ’ s cooling system can hold, refer to Refill capacities in this section.
What you should know about fail-safe cooling (if equipped) If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “ fail-safe ” distance depends on ambient temperatures, vehicle load and terrain.
Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to a service facility . Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to a service facility as soon as possible.
• Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury .
• Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would hold the fuel pump handle in the fill position.
Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use fuel containing methanol. It can damage critical fuel system components. Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives.
Cleaner air Ford endorses the use of reformulated “ cleaner -burning ” gasolines to improve air quality . Running out of fuel A void running out of fuel because this situation may have an adverse affect on powertrain components.
amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty . The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range.
economy under current driving conditions. Additionally , keeping records during summer and winter will show how temperature impacts fuel economy . In general, lower temperatures give lower fuel economy .
• Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle scheduled maintenance guide. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
• Use only the specified fuel listed. • A void running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule.
environment by ensuring that your vehicle continues to meet government emission standards. The OBD-II system also assists the service technician in properly servicing your vehicle. When the Check engine/Service engine soon light illuminates, the OBD-II system has detected a malfunction.
CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary , use only MERCON 威 AT F. Check the fluid level when it is at ambient temperature, 20 °– 80 ° F (-7 ° – 25 ° C): 1.
BRAKE FLUID RESERVOIR The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels below the “ MAX ” line that do not trigger the brake system warning lamp are within the normal operating range, there is no need to add fluid.
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube.
Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in this chapter . Use of a non-approved automatic transmission fluid may cause internal transmission component damage.
Automatic transmission fluid filter (if equipped) The T orqShift automatic transmission is equipped with a serviceable external fluid filter mounted on the driver ’ s side of the transmission. Refer to the Scheduled Maintenance Guide for service intervals.
Changing the air filter element 1. Disconnect the fresh air inlet tube from the radiator support. 2. Loosen the clamp that secures the two halves of the air filter housing together . 3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the housing.
These T ire Quality Grades are determined by standards that the United States Department of T ransportation has set. T ire Quality Grades apply to new pneumatic tires for use on passenger cars.
Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law . The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
INFORMATION CONTAINED ON THE TIRE SIDEWALL Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.
7. H: Indicates the tire ’ s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure.
sidewall. T ire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester , and others. 11.
Additional information contained on the tire sidewall for “ LT ” type tires “ LT ” type tires have some additional information than those of “ P ” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks.
Information on “ T ” type tires T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different than this example. 1. T: Indicates a type of tire, designated by the T ire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks.
Use the recommended cold inflation pressure for optimum tire performance and wear . Under -inflation or over -inflation may cause uneven treadwear patterns.
6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts, bulges or other irregularities.
Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or damage to your tires. If your vehicle seems to pull to one side when you ’ re driving, the wheels may be out of alignment.
• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD) vehicles (front tires at top of diagram) 2004 Econoline (eco) Owners Gui.
Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln/Mercury dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
• Severe abrasion on the sidewall If your vehicle has a leak in the exhaust system, a road tire or the spare tire may be exposed to hot exhaust temperatures requiring the tire to be replaced. Tire Replacement Requirements Y our vehicle is equipped with tires designed to provide safe ride and handling capability .
T ire explosions can cause death, personal injury or property damage. Do not allow anyone to stand near , directly ahead or behind the spinning tire. Never spin the tires in excess of the 55 km/h (35 mph) point indicated on the speedometer .
• Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads. • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.
Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used. Refer to V ehicle Emissions Control Information (VECI) decal for spark plug gap information.
Fluid Ford Part Name Application Capacity Engine coolant-gasoline engine 1 Motorcraft Premium Gold Engine Coolant (yellow-colored) 4.6L V8 engine 23.7L (25.0 quarts) 1 row – 22.6L (23.8 quarts) 8 4.6L V8 engine with aux rear heat 25.7L (27.2 quarts) 1 row – 24.
Fluid Ford Part Name Application Capacity Rear axle 4 Motorcraft SAE 75W -90 Fuel Efficient High Performance Synthetic rear axle lubricant 2 Visteon 8.8/9.75 inch conventional and T raction-Lok 2.6 (5.5 pints) 3 SAE 75W -140 Synthetic Rear Axle Lubricant 2 Dana M70HD (M273HD) E-350 DSO 3.
Fluid Ford Part Name Application Capacity Fuel tank N/A All regular and extended length vans and wagons 132.4L (35.0 gallons) 138 inch wheelbase (except E-Super Duty) 140.0L (37.0 gallons) 158 inch wheelbase (except E-Super Duty) 140.0L (37.0 gallons) 5 176 inch wheelbase (except E-Super Duty) 140.
1 Add the coolant type originally equipped in your vehicle. 2 If your vehicle ’ s rear axle is filled with a synthetic rear axle lubricant it is considered lubricated for life. These lubricants do not need to be checked or changed unless a leak is suspected, service is required or the axle assembly has been submerged in water .
8 If your vehicle is equipped with a single row radiator , there will be a label on the top side of the radiator indicating “ 1 Row Radiator ” . 9 Use of synthetic or synthetic blend motor oil is not mandatory . Engine oil need only meet the requirements of Ford specification WSS-M2C153 – H and the API Certification mark.
Item Ford part name Ford part number Ford specification Lock cylinders Motorcraft Penetrating and Lock Lubricant Motorcraft XL-1 none Power steering fluid Motorcraft MERCON 威 AT F XT -2-QDX MERCON .
Item Ford part name Ford part number Ford specification Dana M70HD (M273HD) E-350 DSO Dana M60 (M248) E-250/350 DSO limited slip 3 SAE 75W -140 Synthetic Rear Axle Lubricant XY -75W140 – QL WSL-M2C1.
1 Ensure the correct automatic transmission fluid is used. T ransmission fluid requirements are indicated on the dipstick or on the dipstick handle. Check the container to verify the fluid being added is of the correct type. Refer to your Scheduled Maintenance Guide to determine the correct service interval.
V EHICLE DIMENSIONS V an/wagon models E-150 E-250 E-350 (1) Overall height 2050 mm (80.7 in) 2118 mm (83.4 in) 2136 mm (84.1 in) (2) T rack front/rear 1763 (69.4)/1707 mm (67.2 in) 1763 (69.4)/1692 mm (66.6 in) 1763 (69.4)/1687 mm (66.4 in) (3) Overall width (excluding mirrors) 2014 mm (79.
Cutaway/commercial stripped chassis models Body style Dimension E-250 E-350 E-450 Super Duty (1) Overall height Refer to Body Builder for specifications. (2) T rack (Front / Rear) 1763 mm (69.4 in)/ 1 692 mm (66.6 in) Cutaway 1763 mm (69.4 in)/SRW 1831 mm (72.
Body style (3) Overall width Refer to Body Builder for specifications. (4) Wheelbase 3150 mm (124 in) 3505 mm (138 in) 4013 mm (158 in) 4470 mm (176 in) 4013 mm (158 in) 4470 mm (176 in) (5) Overall length Refer to Body Builder for specifications.
Certification label for incomplete vehicles On completed derivations of incomplete vehicles, the certification label is affixed at a location determined by a subsequent stage manufacturer of the completed vehicle. In these cases the completed vehicle is manufactured in two or more stages by two or more separate manufacturers.
Code T ransmission Description U Automatic 4 – speed overdrive (4R70W) T Automatic 4 – speed overdrive (4R44E) E Automatic 4 – speed overdrive (4R100) J Automatic 5 – speed overdrive (5R55E) E.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer .
Splash guards Step bars T onneau covers T ruck caps Wheels Interior style Cell phone holders Consoles Electrochromatic compass/temperature interior mirrors Floor mats Interior trim kits Leather wrappe.
Peace of mind Airbag anti-theft locks First aid and safety kits Full vehicle covers Locking gas cap Navigation systems Remote start V ehicle security systems For maximum vehicle performance, keep the .
A Accessory delay ..........................65 Air bag supplemental restraint system ....................................91, 96 and child safety seats .............. 93 description .......................... 91, 96 disposal ...........................
wheels ...................................... 176 wiper blades ............................ 177 Climate control (see Air conditioning or Heating) ......49, 51 Clock adjust 6-CD in dash .............................25 AM/FM ............................
specifications .................. 231, 234 Exhaust fumes .......................... 114 F Fail safe cooling ........................ 194 Fluid capacities .........................226 Four -Wheel Drive vehicles preparing to drive your vehicle .........
J Jump-starting your vehicle ......159 K Keys positions of the ignition ......... 111 L Lamps bulb replacement specifications chart .................. 55 daytime running light ...............52 headlamps ................................. 52 headlamps, flash to pass .
for adults ............................. 82 – 83 for children .........................95, 97 lap belt ...................................... 85 safety belt maintenance ........... 90 warning light and chime .......... 86 Safety seats for children .
W ater , Driving through ............. 124 W indows power ......................................... 65 W indshield washer fluid and wipers .......................................... 60 checking and adding fluid ..... 183 replacing wiper blades .......
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Ford AM/FM stereo c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Ford AM/FM stereo - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Ford AM/FM stereo, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Ford AM/FM stereo va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Ford AM/FM stereo, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Ford AM/FM stereo.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Ford AM/FM stereo. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Ford AM/FM stereo ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
