Manuel d'utilisation / d'entretien du produit 500c (2016) du fabricant Fiat
Aller à la page of 442
OWNER’S MANUAL 2016 FIA T ® 500/500c I n f o r m a t i o n P r o v i d e d b y :.
VEHICLES SOLD IN CANADA W ith respect to any V ehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefor e. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION . .............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .................................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ....
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS 䡵 INTRODUCTION ........................ 4 䡵 HOW TO USE THIS MANUAL .............. 5 䡵 W ARNINGS AND CAUTIONS ..............
INTRODUCTION Congratulations on selecting your new vehicle. Be as- sured that it r epresents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles.
HOW TO USE THIS MANUAL Consult the T able of Contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment.
6 INTRODUCTION I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This Owner ’s Manual contains W ARNINGS against operating procedur es that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedur es that could result in damage to your vehicle. If you do not read this entire Owner ’s Manual, you may miss important information.
NOTE: It is illegal to remove or alter the VIN. VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A WORD ABOUT YOUR KEYS ............. 1 1 ▫ Ignition Key Removal ................... 1 2 ▫ Locking Doors W ith A Key ................ 1 4 ▫ Key-In-Ignition Reminder ................ 1 4 䡵 SENTR Y KEY .
䡵 DOOR LOCKS ......................... 2 2 ▫ Power Door Locks — If Equipped .......... 2 4 ▫ Auto Door Locks ...................... 2 5 䡵 POWER WINDOWS ..................... 2 5 ▫ Power W indow Switches ................. 2 5 ▫ Auto-Down .
A WORD ABOUT YOUR KEYS The key fob contains the Remote Keyless Entry (RKE) transmitter with an integrated key . T o use the mechanical key , simply push the mechanical key release button.
Ignition Key Removal 1. Place the shift lever in P ARK (if equipped with an automatic transmission). 2. Rotate the key to the OFF/LOCK position. 3. Remove the key fr om the ignition switch lock cylinder .
W ARNING! • Before exiting a vehicle, always shift the transmis- sion into P ARK, apply the parking brake, turn the engine OFF , remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
Locking Doors With A Key Y ou can insert the key with either side up. T o lock the door , turn the key to the left. T o unlock the door , turn the key to the right. Refer to “Body Lubrication” in “Main- taining Y our V ehicle” for maintenance procedures.
CAUTION! (Continued) • The Sentry Key Immobilizer system is not compat- ible with some aftermarket remote starting sys- tems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics.
VEHICLE SECURITY ALARM The V ehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition for unauthorized operation. If something triggers the alarm, the V ehicle Security.
NOTE: The line of transmission must not be blocked with metal objects. T o Unlock The Doors And Liftgate Push and release the UNLOCK button on the RKE transmitter once to unlock the driver ’s door or twice, within five seconds, to unlock all doors and the liftgate.
Opening Power T op Remote Function The remote keyless power top function can only be used with the engine off. NOTE: The remote keyless power top function can be used to open the power top to the spoiler position. Opening Power T op Remote Function: 1.
W ARNING! (Continued) • Never place any extremities (hands, feet, etc.) near the convertible top components, the upper wind- shield area, the shelf area behind the rear seats, or the convertible top stowage area while raising or lowering the convertible top.
1. Push the mechanical key r elease button and r elease the mechanical key to access the battery case screw lo- cated on the side of the Key Fob. 2. Rotate the screw located on the side of the Key Fob using a small screwdriver .
3. T ake out the battery case. Remove and replace the battery observing its polarity . 4. Refit the battery case inside the Key Fob and turn the screw to lock it into place.
DOOR LOCKS The door locks can be manually locked or unlocked from inside the vehicle by using the door handle. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock.
W ARNING! • Do not leave children or animals inside parked vehicles in hot weather . Interior heat build-up may cause serious injury or death. • For personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
Power Door Locks — If Equipped A power door lock switch is incorporated into the driver door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the driver ’s door handle is pushed a red lock indicator will show on the driver ’s door handle (indicating locked) when the door is closed, the door will lock.
Auto Door Locks When enabled, the door locks will lock automatically when the vehicles speed exceeds 12 mph (20 km/h). T o change the setting pr oceed as follows: 1. Briefly push the MENU button to enter the MENU screen. 2. Push the UP or DOWN button to highlight “Auto Door Locks”.
W ARNING! (Continued) location accessible to children. Occupants, particu- larly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-Down The driver’s door window switch has an Auto-Down feature.
second, release, and the window will go down automati- cally . T o cancel the Auto-Down movement, operate the switch in either the up or down direction and release the switch. Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter-type sound in the ears.
W ARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. Y ou and your passengers could be injured by these fumes.
2. If a child fr om 2 to 12 years old (not in a rear -facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint.
W ARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger , including a child in a rear- facing child restraint. • Only use a rear-facing child restraint in a vehicle with a rear seat.
the Seat Belt Reminder Light will turn on and r emain on until both outboard front seat belts are buckled. The outboard front passenger seat BeltAlert is not active when an outboard front passenger seat is unoccupied.
NOTE: If BeltAlert has been deactivated and the driver or outboard front seat passenger (if equipped with out- board front passenger seat BeltAlert) is unbuckled the Seat Belt Reminder Light will turn on and r emain on until the driver and outboard front seat passenger seat belts are buckled.
W ARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly . • W earing your seat belt incorrectly could make your injuries in a collision much worse.
W ARNING! (Continued) • A seat belt that is too loose will not protect you properly . In a sudden stop, you could move too far forward, increasing the possibility of injury . W ear your seat belt snugly . • A seat belt that is worn under your arm is dangerous.
3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt.
5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not r esting on your neck. The r etractor will withdraw any slack in the shoulder belt. 6. T o release the seat belt, push the red button on the buckle.
4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Seat Belt Extender If a seat belt is not long enough to fit pr operly , even when the.
Seat Belts And Pregnant W omen Seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong bones of the hips.
The pretensioners are triggered by the Occupant Re- straint Controller (ORC). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately .
seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR. If the ALR is activated, you will hear a clicking sound as the seat belt retracts.
How T o Disengage The Automatic Locking Mode Unbuckle the combination lap/shoulder belt and allow it to r etract completely to disengage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking mode.
• Supplemental Side Air Bags • Supplemental Knee Air Bags • Front and Side Impact Sensors • Seat Belt Pretensioners • Seat Belt Buckle Switch • Seat T rack Position Sensors Advanced Front Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems.
W ARNING! • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury , including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
W ARNING! • No objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • Do not put anything on or around the air bag covers or attempt to open them manually .
Because air bag sensors measur e vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away from an inflating air bag.
provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and Advanced Front Air Bags. Supplemental Side Air Bags Y our vehicle is equipped with two types of supplemental Side Air Bags: 1. Supplemental Seat-Mounted Side Air Bags (SABs): Located in the outboard side of the front seats.
deploys thr ough the seat seam into the space between the occupant and the door . The SAB moves at a very high speed and with such a high force that it could injure occupants if they ar e not seated properly , or if items are positioned in the area where the SAB inflates.
The SABIC deploys downward, covering the side win- dows. An inflating SABIC pushes the outside edge of the headliner out of the way and covers the window . The SABICs inflate with enough force to injure occupants if they ar e not belted and seated properly , or if items are positioned in the ar ea where the SABICs inflate.
The SABICs and SABs (“Side Air Bags”) ar e designed to activate in certain side impacts. The Occupant Restraint Controller (“ORC”) determines whether the deployment of the Side Air Bags in a particular impact event is appropriate, based on the severity and type of collision.
be properly restrained in a child restraint or booster seat that is appropriate for the size of the child. W ARNING! • Side Air Bags need room to inflate. Do not lean against the door or window . Sit upright in the center of the seat. • Being too close to the Side Air Bags during deploy- ment could cause you to be severely injured or killed.
• As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat.
Enhanced Accident Response System In the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the ORC will determine whether to have the Enhanced Accident Response Sys- tem perform the following functions: • Cut off fuel to the engine.
Customer Action Customer W ill See 1. T urn Ignition OFF . (T urn Signal Switch Must Be Placed In Neutral State). 2. T urn Ignition ON. Left T urn Light Is OFF . Right T urn Light BLINKS. 3. T urn Right T urn Signal Switch ON. Right T urn Light Is ON SOLID.
Air Bag W arning Light The air bags must be ready to inflate for your pr otection in a collision. The Occupant Restraint Control- ler (ORC) monitors the internal circuits and interconnecting wiring associated with air bag system electrical components.
• The Air Bag W arning Light comes on intermittently or remains on while driving. NOTE: If the speedometer , tachometer , or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. In this condition the air bags may not be r eady to inflate for your protec- tion.
W ARNING! (Continued) not function properly if modifications are made. T ake your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer .
NOTE: EDR data are recor ded by your vehicle only if a non-trivial crash situation occurs; no data are recor ded by the EDR under normal driving conditions and no per- sonal data (e.
There are differ ent sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner ’s Manual to make sure you have the correct seat for your child.
Summary Of Recommendations For Restraining Children In V ehicles Child Size, Height, W eight Or Age Recommended T ype Of Child Restraint Infants and T oddlers Children who are two years old or younger.
Infants And Child Restraints Safety experts recommend that children ride rear -facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child r estraint. T wo types of child restraints can be used rear -facing: infant carriers and convertible child seats.
remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly .
Children T oo Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.
Recommendations For Attaching Child Restraints Restraint T ype Combined W eight of the Child + Child Restraint Use any attachment method shown with an “X” Below LA TCH – Lower Anchors Only Seat Belt Only LA TCH – Lower Anchors + T op T ether Anchor Seat Belt + T op T ether Anchor Rear-Facing Child Restraint Up to 65 lbs (29.
Lower Anchors And T ethers For CHildren (LA TCH) Restraint System Y our vehicle is equipped with the child restraint anchor- age system called LA TCH, which stands for Lower Anchors and T ethers for CHildren. The LA TCH system has three vehicle anchor points for installing LA TCH- equipped child seats.
LA TCH Positions For Installing Child Restraints In This V ehicle • Lower Anchorage Symbol 2 anchorages per seating position • T op T ether Anchorage Symbol 2 THINGS TO KNOW BEFORE ST ARTING YOUR .
What is the weight limit (child’s weight + weight of the child restraint) for using the LA TCH anchorage system to attach the child restraint? 65 lbs (29.5 kg) Use the LA TCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.
Can the rear -facing child restraint touch the back of the front passenger seat? Y es The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner ’s manual for more in- formation.
Locating T ether Anchorages There are tether strap anchorages behind each rear seating position located on the back of the seat. LA TCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
Always follow the directions of the child restraint manu- facturer when installing your child restraint. Not all child restraint systems will be installed as described here.
6. T est that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.
Installing Child Restraints Using The V ehicle Seat Belt The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
What is the weight limit (child’s weight + weight of the child re- straint) for using the T ether Anchor with the seat belt to attach a forward facing child restraint? W eight limit of the Child Res.
Installing A Child Restraint With A Switchable Automatic Locking Retractor (ALR) 1. Place the child seat in the center of the seating position. For some second r ow seats, you may need to recline the seat and/or raise the head restraint to get a better fit.
strap. See the section “Installing Child Restraints Using the T op T ether Anchorage” for directions to attach a tether anchor . 9. T est that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.
tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat.
W ARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap.
CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem.
Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the seat belt system periodically , checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision.
unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. W ARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury .
Periodic Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tr ead wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks.
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 POWER CONVER TIBLE TOP — IF EQUIPPED . .86 ▫ Lowering The Power T op ................. 8 6 ▫ Raising The Power T op .................. 8 7 ▫ Power Convertible T op Relearn Procedur e ..
䡵 TO OPEN AND CLOSE THE HOOD ........ .102 䡵 LIGHTS ............................ .104 ▫ Multifunction Lever .................. .104 ▫ Headlights ......................... .104 ▫ High Beams ........................ .105 ▫ Flash-T o-Pass ...
▫ Rear Park Assist W arning Display .......... 1 1 9 ▫ Rear Park Assist Display ................ 1 1 9 ▫ Rear Park Assist Audible Alerts .......... .120 ▫ Failure Indications .................... .122 ▫ Cleaning The Rear Park Assist System .
POWER CONVERTIBLE TOP — IF EQUIPPED On vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, is used to open the power top, and the driver side button, is used to close the power top.
NOTE: V ertical movement only operates in auto open/ close mode. Raising The Power T op Auto Close From the convertible top fully open position, push the top close button for approximately one second for the three-quarter open/spoiler position. Push the top close button for approximately one second a second time for the one-quarter open position.
W ARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants in a collision. Therefore, it is impor- tant that all occupants wear their seat belts at all times.
This will confirm that the relearn procedur e was success- ful. Auto Open/Close will now be functional. T runk lid operation will be functional. Remote Keyless Power T op Function will be functional. NOTE:DO NOT interrupt this activity . If the power convertible top does not relearn, r epeat the procedur e a second time.
Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. Y ou can turn the feature on or off by pushing the button at the base of the mirror . The On/Off symbol on the button will illuminate when the auto-dimming feature is enabled.
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean. Power Mirrors The power mirror controls are located on the driver ’s door trim panel.
Using the mirror control switch, push on any of the four arrows for the dir ection that you want the mirr or to move. W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “Rear W indow Features” in “Understanding The Features Of Y our V ehicle” for further information.
W ARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
W ARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Seat Height Adjustment The driver ’s seat height can be raised or lowered by using a lever , located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height. EZ Entry Feature The driver and front passenger seats have an EZ entry feature for rear seat passengers.
Lift the seatback upright and push the seat rearward to its locked position once the rear passengers are seated. Memory Feature Both front seats have a memory feature, which can operate in two ways: M.
W ARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time.
Reactive Head Restraints — Front Seats The front driver and passenger seats are equipped with Reactive Head Restraints. In the event of a rear impact the Reactive Head Restraints will automatically extend forward minimizing the gap between the back of the occupant’s head and the Reactive Head Restraint.
Reactive Head Restraints do not return to their normal position, see your authorized dealership immediately . NOTE: The head restraints should only be removed by qualified technicians, for service purposes only . If either of the head restraints require r emoval, see your autho- rized dealership.
NOTE: T o remove the head restraint, raise it as far as it can go then push the release button and the adjustment button at the base of each post while pulling the head restraint up. T o reinstall the head restraint, put the head restraint posts into the holes and push downwar d.
W ARNING! ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat. TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be r eleased.
3. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the engine compartment. Place the hood prop rod in the hole of hood hinge to secure the hood in the open position. In hot climates, the prop r od may be hot.
CAUTION! T o prevent possible damage, do not slam the hood to close it. Lower hood to approximately 12 in (30 cm) and drop the hood to close. Make sure hood is fully closed for both latches. Never drive vehicle unless hood is fully closed, with both latches engaged.
NOTE: When the headlights are turned on, the Daytime Running Lights will be deactivated. High Beams W ith the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams.
Daytime Running Lights T o activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O symbol. NOTE: The low beams and side/taillights will not be on with DRL. If allowed by law in the country in which the vehicle was purchased the DRL function can be turned on or of f using the display menus.
Lane Change Assist T ap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Follow Me Home/Headlight Delay When this feature is selected the driver can choose to have the headlights remain on for a preset period of time.
on the right light and push the switch to the left to turn on the left light. CAUTION! Before getting out of the vehicle be sure that the switch is in the center position or that the lights are off to avoid draining the battery .
Push the switch once to turn the fr ont fog lights on. Push the switch a second time to turn the front fog lights off. WINDSHIELD WIPERS AND W ASHERS The windshield wiper/washer lever is located on the right side of the steering column. NOTE: The windshield wipers/washers will only oper- ate with the ignition in the ON/RUN position.
Front Windshield Wiper Operation There are five differ ent modes of operation for the front windshield wipers. The windshield wiper lever can be raised or lowered to access these modes: W indshield W iper Off This is the normal position of the wiper lever .
Manual High Speed/Mist Push the lever upward fr om the off position. The wipers will operate at high speed to clear off road mist or spray from a passing vehicle. This operation will continue until the lever is released. When the lever is released, the wipers will return to the off position and automatically shut off.
Rear Windshield Wiper Rotate the end of the windshield wiper/washer lever upward to the first detent past the intermittent settings for intermittent wipe operation. W ith the front wind- shield wiper active, r otate the end of the windshield wiper/washer lever upward.
hold the lever for mor e than a half second and the wipers will activate automatically for three cycles after the lever is released. TIL T STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward. The tilt control lever is located on the left-side of the steering column, below the turn signal controls.
W ARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
NOTE: In order to ensure proper operation, the Elec- tronic Speed Control system has been designed to shut down if multiple Speed Contr ol functions are operated at the same time. If this occurs, the Electronic Speed Contr ol system can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
T o Deactivate A soft tap on the brake pedal, pushing the CANC button, or normal brake pressur e while slowing the vehicle will deactivate Electr onic Speed Contr ol without erasing the set speed memory . Pushing the ON/OFF button or turning the ignition switch OFF erases the set speed in memory .
• If the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed will be established. T o Decrease Speed When the Electronic Speed Control is set, you can de- crease speed by pushing the SET (-) button.
Using Electronic Speed Control On Hills The transmission may downshift on hills to maintain the vehicle set speed. NOTE: The Electronic Speed Contr ol system maintains speed up and down hills.
If several obstacles are detected, the Rear Park Assist system indicates the nearest obstacle. The minimum height of a detectable obstacle corre- sponds to the maximum height of an obstacle that would clear the underside of the car during the parking maneu- ver .
Rear Park Assist Audible Alerts If an obstacle is behind the vehicle when the transmission is placed into REVERSE, an audible alert is activated. The tones emitted by the loudspeaker inform the driver that the vehicle is approaching an obstacle. The pauses between the tones are directly proportional to the dis- tance fr om the obstacle.
Audible And Visual Signals Supplied By The Rear Park Assist System SIGNAL MEANING INDICA TION Obstacle Distance An obstacle is present within the sensors’ field of view Audible signal (dashboard loudspeaker) • Sound pulses emitted at a rate that increases as the distance decreases.
While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance incr eases. The tone cycle remains constant if the distance measur ed by the inner sensors is constant.
cm) from the sensors. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. Park Assist System Usage Precautions NOTE: • Ensure that the outer surface and the underside of the rear bumper is clean and clear of snow , ice, mud, dirt or other obstruction to keep the Rear Park Assist system operating properly .
CAUTION! (Continued) • The vehicle must be driven slowly when using Rear Park Assist in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using Rear Park Assist. W ARNING! • Drivers must be careful when backing up even when using the Rear Park Assist system.
POWER SUNROOF — IF EQUIPPED The power sunroof roof switch is located in the overhead console. W ARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location acces- sible to children.
T o Open Push and hold the power sunroof switch rearwar d for approximately one second and the sunroof will stop at the vented position. Push the switch a second time and hold for approximately one second and release, the sunroof will open fully , then stop automatically .
Emergency Operation In case of electrical failure, the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof.
ELECTRICAL POWER OUTLETS There is a standard 12 V olt (13 Amp) power outlet, located in the floor console, for added convenience. This power outlet can power mobile phones, electronics and other low power devices. Power is available when the ignition switch is in the ON/RUN or ST AR T position.
W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly .
For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. Front Cupholders Rear Cupholders 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 131 I n f o.
STORAGE Glove Compartment The glove compartment is located on the right side of the instrument panel. Pull outward on the glove compart- ment latch to open the glove compartment. Push the glove compartment door upward to close it. CARGO AREA FEA TURES The rear seatbacks have a fold down feature to allow increased cargo capacity .
Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area. When r eturning the seatback to its upright position, push rearwar d until the seatback is properly latched.
Push this button to turn on the rear window defroster . An indicator in the instrument cluster will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 20 minutes. T o manually shut the defroster off, push the button a second time.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 INSTRUMENT P ANEL FEA TURES ......... .138 䡵 INSTRUMENT CLUSTER ................ .139 䡵 INSTRUMENT CLUSTER — ECO .......... .142 䡵 INSTRUMENT CLUSTER ................ .146 䡵 W ARNING AND INDICA TOR LIGHTS .
▫ V alues Displayed ..................... .182 ▫ Personal Settings (Customer-Pr ogrammable Features) ........................... .183 䡵 CYBERSECURITY ...................... .189 䡵 UCONNECT RADIOS .................. .191 䡵 iPod/USB/MEDIA PLA YER CONTROL — IF EQUIPPED .
䡵 CLIMA TE CONTROLS .................. .210 ▫ Manual Heating And Air Conditioning ...... 2 1 1 ▫ Automatic T emperature Control (A TC) ..... .213 ▫ Operating T ips .
INSTRUMENT P ANEL FEA TURES 1 — Side V ent 7 — Passenger Air Bag 13 — Storage Compartment 2 — Multifunction Lever – Light Control 8 — Glove Compartment 14 — Shift Lever 3— Instrument C.
INSTRUMENT CLUSTER Instrument Cluster 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 139 I n f o r m a t i o n P r o v i d e d b y :.
1. T achometer • This gauge measures engine revolutions per minute (RPM x 1000). Befor e the pointer reaches the red ar ea, ease up on the accelerator to prevent engine damage. 2. T emperature Gauge • The temperature gauge shows engine coolant tem- perature.
3. Speedometer • Indicates vehicle speed. 4. Fuel Gauge • The digital display shows the amount of fuel in the tank. • The switching on of the digital warning light indi- cates that 1 – 1.3 gallons of fuel are left in the tank; in this situation, refuel as soon as possible.
INSTRUMENT CLUSTER — ECO ECO Instrument Cluster 142 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
1. T achometer • This gauge measures engine revolutions per minute (RPM x 1000). Befor e the pointer reaches the red ar ea, ease up on the accelerator to prevent engine damage. 2. T emperature Gauge • The temperature gauge shows engine coolant tem- perature.
3. Speedometer • Indicates vehicle speed. 4. Fuel Gauge • The digital display shows the amount of fuel in the tank. • The switching on of the digital warning light indi- cates that 1 – 1.3 gallons of fuel are left in the tank; in this situation, refuel as soon as possible.
every second and takes into account a combination of the instant fuel economy and your driving style dur- ing the current trip. NOTE: Differ ent trips may have different values even if the same driving style is maintained.
INSTRUMENT CLUSTER Base Instrument Cluster 146 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
1. Speedometer • Indicates vehicle speed. 2. T achometer • This gauge measures engine revolutions per minute (RPM x 1000). Befor e the pointer reaches the red ar ea, ease up on the accelerator to prevent engine damage. 3. T emperature Gauge • The temperature gauge shows engine coolant tem- perature.
4. Fuel Gauge • The digital display shows the amount of fuel in the tank. • The switching on of the digital warning light indi- cates that 1 – 1.
Red T elltale Indicator Lights Air Bag W arning Light Red T elltale Light What It Means Air Bag W arning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN.
Seat Belt Reminder W arning Light Red T elltale Light What It Means Seat Belt Reminder W arning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
Electric Power Steering Fail W arning — If Equipped Red T elltale Light What It Means Electric Power Steering Fail W arning — If Equipped This light is used to manage the electrical warning of the EPS (Power Steering System). Re- fer to “Power Steering” in “Starting and Operating” for further information.
Red T elltale Light What It Means United States Canada If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir , it.
W ARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. Y ou could have a collision. Have the vehicle checked immediately . V ehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).
Charging System W arning Light Red T elltale Light What It Means Charging System W arning Light This light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s nonessential electrical devices or increase engine speed (if at idle).
Electronic Throttle Control (ETC) W arning Light Red T elltale Light What It Means Electronic Throttle Control (ETC) W arning Light This light informs you of a problem with the Electronic Throttle Contr ol (ETC) system.
Oil Pressure W arning Light Red T elltale Light What It Means Oil Pressure W arning Light This light indicates low engine oil pressur e. If the light turns on while driving, stop the ve- hicle and shut off the engine as soon as possible. A chime will sound when this light turns on.
Engine T emperature W arning Light Red W arning Light What It Means Engine T emperature W arning Light This light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold.
Door Open W arning Light Red T elltale Light What It Means Door Open W arning Light This indicator will illuminate when a door is ajar/open and not fully closed.
Liftgate Open W arning Light Red T elltale Light What It Means Liftgate Open W arning Light This indicator will turn when the liftgate is open. T ransmission Fault W arning Light Red T elltale Light W.
Hood Open W arning Light Red T elltale Light What It Means Hood Open W arning Light This indicator will illuminate when the hood is ajar/open and not fully closed.
IMPOR T ANT : Do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. Repair immediately using the dedicated tire repair kit and contact your authorized dealership as soon as possible.
illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tir e pressure as intended.
Electronic Stability Control (ESC) Activation/Malfunction Indicator Light Y ellow T elltale Light What It Means Electronic Stability Control (ESC) Activation/Malfunction Indicator Light The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position.
Electronic Stability Control (ESC) OFF Indicator Light Y ellow T elltale Light What It Means Electronic Stability Control (ESC) OFF Indicator Light This light indicates the Electronic Stability Control (ESC) is off. For further information, r efer to “Electronic Stability Control (ESC)” in “Starting And Operating.
Engine Check/Malfunction Indicator Light (MIL) Y ellow T elltale Light What It Means Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.
CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur .
Rear Fog Light Indicator — If Equipped Y ellow T elltale Light What It Means Rear Fog Light Indicator This indicator will illuminate when the rear fog lights are on. Rear Defrost Light Y ellow T elltale Light What It Means Rear Defrost Light This indicator will illuminate when the rear window defroster is on.
CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window . Do not use abrasive window cleaners on the interior surface of the window . Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
Anti-Lock Brake (ABS) Indicator Light Y ellow T elltale Light What It Means Anti-Lock Brake (ABS) Indicator Light After the ignition is turned on, the Anti-Lock Brake System (ABS) light illuminates to indi- cate function check at vehicle startup.
Generic W arning Indicator Light Y ellow T elltale Light What It Means Generic W arning Indicator Light The Generic W arning Light will illuminate if any of the following conditions occur: Oil Change Request, Engine Oil Pressur e Sensor Failure, External Light Failure, Fuel Cut-Off Not A vailable, Parking Sensor Failur e, DST System Failure.
Exterior Bulb Failure Indicator Light Y ellow T elltale Light What It Means Exterior Bulb Failure Indicator Light This light will illuminate when there is a malfunction in one of the exterior bulbs.
Glow Plug Light — If Equipped Y ellow T elltale Light What It Means Glow Plug Light — If Equipped This vehicle will inhibit engine cranking when the ambient temperature is less than –22° F (–30° C) and the oil temperature sensor reading indicates an engine block heater has not been used.
Green T elltale Indicator Lights T urn Signal Indicator Lights Green T ell- tale Light What It Means T urn Signal Indicator Lights The instrument cluster arr ow will flash independently for the LEFT o.
Front Fog Indicator Light — If Equipped Green T elltale Light What It Means Front Fog Indicator Light This indicator will illuminate when the front fog lights are on. Cruise Control Engaged Indicator Light Green T elltale Light What It Means Cruise Control Engaged Indicator Light This light will turn on when the cruise contr ol has been engaged.
Blue T elltale Indicator Light High Beam Indicator Light Blue T elltale Light What It Means High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam.
White T elltale Indicator Light Electronic Speed Control ON Indicator Light White T elltale Light What It Means Electronic Speed Control ON Indicator Light This light will turn on when the electronic speed control is ON.
ELECTRONIC VEHICLE INFORMA TION CENTER (EVIC) The Electronic V ehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the instrument cluster .
EVIC Control Buttons Push and release the MENU button briefly to access the EVIC. Push and hold the MENU button (appr oximately one second) to return to the main screen. Push and release the UP button to scroll upward through the displayed menu and the related options or to increase the displayed value.
• Audio Repetition • Navigation Repetition — If Equipped • Speed Display (Comfort V ersion Only) • Buzzer V olume • GSI Shift (manual transmission only) • Exit Menu Selecting An Option Of The Main Menu Without Submenu 1. Briefly push and release the MENU button to select the main menu option to set.
6. Push and hold the MENU button to return to the main menu (short hold) or the main screen (longer hold). Change Engine Oil Indicator System Change Engine Oil Y our vehicle is equipped with an engine oil change indicator system.
T rip Button The TRIP button, located on the right steering column stalk, can be used to display and to reset the previously described values. • A short button push displays the dif ferent values. • A long button push resets the system and then starts a new trip.
Tire Pressure This function will be used to display the tire pressures individually for all four tires by location. T rip Functions Both trip functions are resettable (reset — start of new trip).
• The vehicle is parked for a long time with the engine running. NOTE: The range depends on several factors: driving style, type of route (freeway , residential, mountain roads, etc.), and conditions of use of the vehicle (load, tir e pressur e, etc.
T o adjust the brightness, pr oceed as follows: 1. Push and release the UP or DOWN button to set the requir ed brightness level. 2. Briefly push and release the MENU button to go back to the menu screen or push and hold the MENU (approximately one second) to go back to the main screen without storing settings.
T o cancel the setting, pr oceed as follows: 1. Briefly push and release the MENU button. “On” will flash on the display . 2. Push and release the DOWN button.
T o activate (On) or to deactivate (Of f) the sound system info displaying, proceed as follows: 1. Briefly push and release the MENU button. Push and release the UP or Down button to highlight See Radio and push and release the MENU button. 2. Push and release the UP or DOWN button for setting.
Speed Display When this function is activated the cluster will display the vehicle speed (MPH or km/h). T o activate (On) or to deactivate (Off) the speed display feature, proceed as follows: 1. Briefly push and release the MENU button. Push and release the UP or DOWN button to highlight Speed Display .
GSI (Gear Shift Indicator) This function may be used to set the Gear Shift Indicator in two submenus: “On” and “Off.” • On – turns on a fuel economy upshift light in the instrument cluster , for optimum fuel economy , when operating in base driving mode.
CYBERSECURITY Y our vehicle may be a connected vehicle and may be equipped with both wired and wireless networks. These networks allow your vehicle to send and receive infor- mation. This information allows systems and features in your vehicle to function properly .
W ARNING! (Continued) may increase the possibility for vehicle systems to be breached. • As always, if you experience unusual vehicle be- havior , take your vehicle to your nearest authorized dealer immediately . NOTE: • FCA or your dealer may contact you directly regar ding software updates.
UCONNECT RADIOS For detailed information about your Uconnect radio, refer to your Uconnect Supplement Manual. iPod/USB/MEDIA PLA YER CONTROL — IF EQUIPPED This feature allows an iPod or external USB device to be plugged into the USB or AUX port, located in the center console.
UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and change the customer programmable features. Many features can vary by vehicle.
Buttons On The Faceplate Buttons on the faceplate ar e located below , and beside the Uconnect system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side. T urn the control knob to scroll through menus and change settings (i.
press the “X” button on the touchscreen to close out of the settings screen. Pressing the Up or Down Arrow buttons on the right side of the scr een will allow you to toggle up or down through the available settings. NOTE: All settings should be changed with the ignition in the “ A VV/ACC ” position.
• T ouchscreen Beep When in this display , you may turn on or shut off the sound heard when a touchscreen button is pr essed. Press the “T ouchscreen Beep” button on the touchscr een then “On” or “Off.
• Show Command List When in this display , you may change the Show Com- mand List settings. T o change the Show Command List settings, press the “Show Command List” button on the touchscreen and select fr om “Always,” “W ith Help” or “Never .
Safety/Assistance After pressing the “Safety/Assistance” button on the touchscreen the following setting will be available: • Hill Start Assist When this feature is selected, the Hill Start Assist (HSA) system is active.
• Remote Door Unlock/Door Unlock When “Driver” is selected, only the driver ’s door will unlock on the first push of the Remote Keyless Entry (RKE) transmitter UNLOCK button, you must push the RKE transmitter UNLOCK button twice to unlock the passenger ’s doors.
• Balance When in this display you may adjust the Balance settings. • Auto-On Radio The Radio automatically turns on when vehicle is in run or will recall whether it was on or of f at last ignition off. T o make your selection, push the “Settings” button, then “Audio,” then “Auto-On Radio.
• Channel Skip SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning.
Restore Settings After pressing the “Restore Settings” button on the touchscreen the following settings will be available: • Restore Settings When this feature is selected it will reset the Display , Clock, Audio, and Radio Settings to their default settings.
UCONNECT 5.0 VOICE RECOGNITION QUICK TIPS Introducing Uconnect Start using Uconnect V oice Recognition with these help- ful quick tips. It provides the key V oice Commands and tips you need to know to contr ol your Uconnect 5.0 system. Key Features: • 5.
2. Reduce backgr ound noise. W ind and passenger con- versations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned on the rearview mirror and aimed at the driver .
Basic V oice Commands The basic V oice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say ѧ • Cancel to stop a current voice session.
Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear . (Subscrip- tion or included SiriusXM Satellite Radio trial r equired.
Media Uconnect offers connections via USB, Bluetooth and Auxiliary ports (If Equipped). V oice operation is only available for connected USB and iPod devices. Push the VR button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist.
V oice T ext Reply Uconnect will announce incoming text messages. Push the PHONE button and say Listen. (Must have compatible mobile phone pair ed to Uconnect system.) 1. Once an incoming text message is read to you, push the PHONE button . After the beep, say .
by r elocating the mobile phone antenna. This condition is not harmful to the radio. If your radio performance does not satisfactorily “clear” by the repositioning of the antenna, it is recommended that the radio volume be turned down or off during mobile phone operation.
STEERING WHEEL AUDIO CONTROLS The remote sound system controls ar e located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker -type switch with a pushbutton in the center and controls the volume and mode of the sound system.
Radio Operation Pushing the top of the switch will “Seek” up for the next listenable station and pushing the bottom of the switch will “Seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- grammed in the radio preset button.
Manual Heating And Air Conditioning The Manual Climate controls consist of a series of rotary dials and one inner push knob. 1. T emperature Control Rotate this control to r egulate the temperatur e of the air inside the passenger compartment.
NOTE: • Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur . Extended use of this mode is not recommended. • The use of the Recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the vehicle.
requir e extra heat to the windshield. This setting is good for maintaining comfort while reducing mois- ture on the windshield. • Defrost Air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting.
1. AUTO T emperature Control (A TC) Button Controls airflow , temperature, distribution, and air recir- culation automatically . Push and release to select. Per- forming this function will cause the A TC to switch between manual mode and automatic modes.
are selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the AUTO mode. The operator can also select the direction of the airflow by selecting one of the following positions. 5. Mix Mode Air is directed through the floor , defrost, and side window demister outlets.
NOTE: The center instrument panel outlets can be aimed so that they ar e directed toward the rear seat passengers for maximum airflow to the rear . 9. Bi-Level Air is directed through the panel and floor outlets. Press and r elease the Panel mode button and Floor mode button to enter Bi-Level mode, the indicators illuminate when ON.
outlets. If Economy mode is desired, push the A/C button to turn off the A/C mode in the A TC display and deactivate the A/C system. NOTE: • If the system is in Mix or Defr ost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.
2. Next, adjust the temperature you would like the system to maintain by adjusting the temperature con- trol buttons. Once the desired temperature is dis- played, the system will achieve and automatically maintain that comfort level. 3. When the system is set up for your comfort level, it is not necessary to change the settings.
Operating Tips NOTE: Refer to the chart at the end of this section for suggested contr ol settings for various weather condi- tions. W indow Fogging W indows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid.
W inter Operation When operating the system during the winter months, make sure the air intake, located directly in front of the windshield, is fr ee of ice, slush, snow , or other obstruc- tions. V acation Storage Anytime you store your vehicle, or keep it out of service (i.
Operating T ips Chart 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 221 I n f o r m a t i o n P r o v i d e d b y :.
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS 䡵 ST AR TING PROCEDURES ............... .227 ▫ Manual T ransmission — If Equipped ...... .227 ▫ Automatic T ransmission — If Equipped .... .227 ▫ Normal Starting ...................... .227 ▫ Cold W eather Operation .
䡵 AUTOSTICK ......................... .242 ▫ Operation .......................... .242 䡵 DRIVING ON SLIPPER Y SURF ACES ........ .243 ▫ Acceleration ........................ .243 ▫ T raction ........................... .244 䡵 DRIVING THROUGH W A TER .
䡵 TIRES — GENERAL INFORMA TION ....... .273 ▫ T ir e Pressur e ....................... .273 ▫ T ir e Inflation Pressur es ................ .274 ▫ T ir e Pressur es For High Speed Operation . . . .276 ▫ Radial Ply T ir es ..................
▫ Fuel System Cautions .................. .299 ▫ Carbon Monoxide W arnings ............ .300 䡵 ADDING FUEL ....................... .301 ▫ Fuel Filler Cap (Gas Cap) .............. .301 ▫ Loose Fuel Filler Cap Message ........... .302 䡵 TRAILER TOWING .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. W ARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
T urn the ignition switch to the A VV/ACC (ST ART) position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the STOP (OFF/LOCK) position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure.
3. If the engine fails to start within ten seconds, cycle the ignition to the STOP (OFF/LOCK) position, wait five seconds to allow the starter to cool, then repeat the Extended Park Starting procedur e. 4. If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedur e.
After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. T urbocharger “Cool Down” This vehicle is equipped with an after -run pump to cool the turbocharger after the engine is shut off.
Fully press the clutch pedal befor e you shift gears. As you release the clutch pedal, lightly press the accelerator pedal. NOTE: T o shift into REVERSE from NEUTRAL, lift the ring under the knob and, at the same time move the gearshift lever to the right and then backward.
NOTE: • Clashing REVERSE gear , especially if vehicle is mov- ing, can result in transmission damage. • During cold weather , until the transmission lubricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the trans- mission.
Downshifting Proper downshifting will improve fuel economy and prolong engine life. CAUTION! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released.
W ARNING! • It is dangerous to shift out of P ARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something.
Key Ignition Park Interlock This vehicle is equipped with a Key Ignition Park Inter- lock which requires the transmission to be in P ARK before the ignition switch can be turned to the LOCK/ OFF (key removal) position.
Only shift from DRIVE to P ARK or REVERSE when the accelerator pedal is released and the vehicle is stopped. Be sur e to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has P ARK, REVERSE, NEU- TRAL, DRIVE, and AutoStick shift positions.
NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. P ARK (P) This range supplements the parking brake by locking the transmission. The engine can be started in this range.
W ARNING! (Continued) vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
CAUTION! • Before moving the shift lever out of P ARK, you must turn the ignition switch from the LOCK/OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from P ARK or NEUTRAL into another gear range, as this can damage the drivetrain.
W ARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
range of torque converter clutch engagement. This is done to pr event transmission damage due to overheat- ing. During cold temperatures, transmission operation may be modified depending on engine coolant temperature. Normal operation will r esume once the engine tempera- ture has risen to a suitable level.
If the transmission cannot be reset, authorized dealer service is requir ed. AUTOSTICK AutoStick is a driver-interactive transmission feature providing manual shift control, giving you more control of the vehicle. AutoStick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance.
in snow or icy conditions. T o select second or third gear after the vehicle is brought to a stop, tap the shift lever rearwar d (+) once or twice. • The system will ignore shift commands that would cause engine lugging or overspeed. An audible beep will sound if an inappropriate gear is requested.
W ARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. Y ou could lose control of the vehicle and possibly have a collision. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow , wet, mud, loose sand, etc.
Flowing/Rising W ater W ARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water . Furthermore, flowing and/or rising water can carry your vehicle away swiftly .
CAUTION! (Continued) standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water .
W ARNING! Continued operation with reduced or no power steer- ing assist could pose a safety risk to yourself and others. Service should be obtained as soon as pos- sible. If the Steering icon is flashing, it indicates that the vehicle needs to be taken to an authorized dealer for service.
P ARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave the manual transmission in REVERSE or first gear . The parking brake lever is located in the center console. T o apply the parking brake, pull the lever up as firmly as possible.
should always be applied whenever the driver is not in the vehicle. W ARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
SPORT MODE Manual T ransmission — If Equipped The Sport mode increases steering feedback to the driver with slight incr eases in ef fort and thr ottle pedal-to-engine response. This driving mode is useful while driving on twisty r oads where more steering precision is desired in spirited cornering.
Automatic T ransmission — If Equipped The Sport mode increases steering feedback to the driver with slight increase in effort and changes the transmis- sion shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired in spirited cornering.
BRAKE SYSTEM Y our vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability , the remaining system will still func- tion.
The ABS includes an amber ABS W arning Light. When the light is illuminated, the ABS is not functioning. The system reverts to standard non-anti-lock brakes. T urning the ignition Off and On again may reset the ABS if the fault detected was only momentary .
Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressur e to the brakes.
stability . A feature of the TCS system, Brake Limited Differ ential (BLD), functions similar to a limited slip differ ential and contr ols the wheel spin acr oss a driven axle. If one wheel on a driven axle is spinning faster than the other , the system will apply the brake of the spinning wheel.
W ARNING! There may be situations on minor hills with a loaded vehicle, or while pulling a trailer , when the system will not activate and slight rolling may occur . This could cause a collision with another vehicle or object. Always remember the driver is responsible for brak- ing the vehicle.
NOTE: The ESC Off switch is located left of the steering column (Manual T ransmission Only). ESC Off Switch (Automatic T ransmission) ESC Off Switch (Manual T ransmission) 5 ST ARTING AND OPERA TING 2.
W ARNING! • The Electronic Stability Control (ESC) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent all accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
ESC Operating Modes The ESC system has two available operating modes. Full On This is the normal operating mode for ESC. Whenever the vehicle is started, the ESC system will be in On mode. This mode should be used for most driving situations. ESC should only be turned to Partial Off for specific reasons as noted below .
W ARNING! (Continued) reduction feature of TCS is disabled, and the enhanced vehicle stability offered by the ESC sys- tem is reduced. ESC Activation/Malfunction Indicator Light And ESC OFF Indicator .
• Each time the ignition is turned ON, the ESC system will be ON even if it was turned off previously . The ESC OFF Indicator Light indicates the Electronic Stability Control (ESC) is partially off.
NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, L T235/85R16C, T145/80D18 103M, 31x10.5 R15 L T P = Passenger car tire size based on U.S. design standards, or ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards, or LT = Light truck tir e based on U.
EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can ca.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tir e.
EXAMPLE: DOT MA L9 ABCD 0301 01 = Number repr esenting the year in which the tire was manufactured (two digits) – 01 means the year 2001 – Prior to July 2000, tire manufacturers were only r equired to have one number to r epresent the year in which the tire was manufactured.
T erm Definition Maximum Inflation Pressure The maximum inflation pressur e is the maximum permissible cold tire inflation pressure for this tir e. The maximum inflation pressur e is molded into the sidewall.
Tire Loading And Tire Pressure T ire And Loading Information Placard Location NOTE: The pr oper cold tire inflation pressur e is listed on the driver ’s side B-Pillar or the rear edge of the driver’s side door .
T ire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2.
3. T ir e size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear , and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
“XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (294 kg) (since 5 x 150 lbs (68 kg) = 750 lbs (340 kg), and 1400 lbs (635 kg) – 750 lbs (340 kg) = 650 lbs [294 kg]).
272 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under -inflation and over-inflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.
judgement when determining proper inflation. T ir es may look pr operly inflated even when they are under - inflated. • Inspect tires for signs of tir e wear or visible damage. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap.
Tire Pressures For High Speed Operation The manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressur e is very important.
Consult an authorized tire dealer for tire repairs and additional information. Damaged Run Flat tires, or Run Flat tires that have experienced a loss of pressur e should be replaced imme- diately with another Run Flat tire of identical size and service description (Load Index and Speed Symbol).
W ARNING! Do not use Summer tires in snow/ice conditions. Y ou could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow T ires Some ar eas of the country require the use of snow tires during the W inter .
Run Flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immedi- ately . A Run Flat tire is not repairable. It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the run flat mode.
Compact Spare T ire — If Equipped The compact spare is for temporary emergency use only . Y ou can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the T ir e and Loading Information Placard located on the driver ’s side door opening or on the sidewall of the tire.
spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity . Limited-Use Spare — If Equipped The limited-use spare tire is for temporary emergency use only .
Refer to “Freeing A Stuck V ehicle” in “What T o Do In Emergencies” for further information. W ARNING! Fast spinning tires can be dangerous. Forces gener - ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one.
worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement T ires” in this section for further information. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style.
wear and correct cold tire inflation pressur es. The manu- facturer strongly r ecommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed. Refer to the paragraph on “T r ead W ear Indicator”.
W ARNING! (Continued) • Never use a tire with a smaller load index or capacity , other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. Y ou could lose control and have a collision.
CAUTION! T o avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted traction device clearance be- tween tires and other suspension components, it is important that only traction devices in good condi- tion are used.
tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “Maintenance Schedule” for the proper maintenance intervals. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.
The tire pr essure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressur e will decrease. T ire pressure should always be set based on cold inflation tire pressur e.
pressur e is sufficiently low enough to turn on the T ir e Pressur e Monitoring T elltale Light. Driving the vehicle may cause the tire pressur e to rise to approximately 27 psi (186 kPa), but the T ire Pressure Monitoring T elltale Light will still be on.
• The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability .
T ire Pressure Monitoring Low Pressure W arnings The T ire Pressur e Monitoring T elltale Light will illumi- nate in the instrument cluster , an audible chime will be activated, and the “Low inflation pressur e left or right front/r ear tire” text message will display when one or more of the four active road tire pr essures ar e low .
NOTE: Y our vehicle may be equipped with a compact spare wheel and tire assembly . • The compact spare tire does not have a tir e pressure monitoring sensor .
monitor tire pressur e levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressur e readings to the receiver module. The TPMS consists of the following components: • Rec.
will automatically update and the “T ire Pressur e Moni- toring T elltale Light” will turn of f. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this informa- tion.
A system fault can occur due to any of the following: 1. Signal interference due to electr onic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals.
turn off as long as no tire pressure is below the low- pressur e warning limit in any of the four active r oad tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in or der for the TPMS to r eceive this information.
Poor quality gasoline can cause problems such as har d starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle. Reformulated Gasoline Many areas of the country requir e the use of cleaner burning gasoline r eferred to as “Reformulated Gasoline”.
are not the responsibility of the manufacturer and may void or not be covered under New V ehicle Limited W arranty . E-85 Usage In Non-Flex Fuel V ehicles Non-Flex Fuel V ehicles (FFV) are compatible with gaso- line containing up to 15% ethanol (E-15).
that have these additives will help improve fuel economy , r educe emissions, and maintain vehicle perfor- mance. Designated TOP TIER Detergent Gasoline con- tains a higher level of detergents to further aide in minimizing engine and fuel system deposits.
CAUTION! (Continued) Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer and may void or not be covered under the New V ehicle Limited W arranty .
ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located on the passenger side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle. CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel filler cap.
W ARNING! (Continued) • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. Y ou could be burned. Always place gas containers on the ground while filling. NOTE: • When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
RECREA TIONAL T OWING (BEHIND MOTORHOME, ETC.) T owing This V ehicle Behind Another V ehicle T owing Condition Wheels OFF the Ground Manual T ransmission Automatic T ransmission Flat T ow NONE T ransm.
CAUTION! • DO NOT flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are OFF the ground. • T owing this vehicle in violation of the above re- quirements can cause severe transmission damage.
WHA T TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD W ARNING FLASHERS .......... .307 䡵 IF YOUR ENGINE OVERHEA TS ........... .307 䡵 TIRE SER VICE KIT — IF EQUIPPED ........ .308 ▫ T ir e Service Kit Storage ................ .309 ▫ T ir e Service Kit Components And Operation .
▫ Jump-Starting Procedur e ............... .336 䡵 FREEING A STUCK VEHICLE ............ .337 䡵 SHIFT LEVER OVERRIDE ............... .339 䡵 TOWING A DISABLED VEHICLE .......... .340 ▫ Automatic T ransmission ................ .341 ▫ Manual T ransmission .
HAZARD W ARNING FLASHERS The Hazard W arning flasher switch is located on the instrument panel below the radio. Push the switch to turn on the Hazard W arning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency .
supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle.
Tire Service Kit Storage The T ire Service Kit is located under the front driver’s seat. Tire Service Kit Components And Operation T ire Service Kit Location T ire Service Kit Components 1 — Seala.
Using The Mode Select Knob And Hoses Y our T ir e Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only . Use the Black Air Pump Hose (7) when selecting this mode.
• The Sealant Bottle (1) and Sealant Hose (6) are a one tire application use and need to be replaced after each use. Always replace these components immediately at your original equipment vehicle dealer .
W ARNING! • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the T ire Service Kit.
W ARNING! (Continued) • T ire Service Kit Sealant solution contains latex. In case of an allergic reaction or rash, consult a phy- sician immediately . Keep T ire Service Kit out of reach of children. If swallowed, rinse mouth imme- diately with plenty of water and drink plenty of water .
4. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose (6) onto the valve stem. 5. Uncoil the Power Plug (8) and insert the plug into the vehicle’s 12 V olt power outlet. NOTE: Do not remove foreign objects (e.
NOTE: If the Mode Select Knob (5) is on Air Mode and the pump is operating, air will dispense from the Air Pump Hose (7) only , not the Sealant Hose (6). If the sealant (white fluid) does flow through the Sealant Hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hose (typically takes 30 - 70 seconds).
3. Immediately disconnect the Sealant Hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the T ir e Service Kit in the vehicle storage location.
(E) After Driving: Pull over to a safe location. Refer to “Whenever Y ou Stop to Use T ire Service Kit” before continuing. 1. Push in the Mode Select Knob (5) and turn to the Air Mode position. 2. Uncoil the power plug and insert the plug into the vehicle’s 12 V olt power outlet.
5. Remove the Speed Limit sticker from the instrument panel after the tire has been repaired. 6. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized dealer as soon as pos- sible. Refer to (F) “Sealant Bottle and Hose Replace- ment”.
WHEEL AND TIRE TORQUE SPECIFICA TIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench.
T ighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt tor que to be sure that all the lug nuts/bolts are properly seated against the wheel.
W ARNING! (Continued) under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Never start or run the engine while the vehicle is on a jack. • The jack is designed to be used as a tool for changing tires only .
Spare Tire Removal The spare tire is stowed to the underbody below the cargo area. 1. Remove the plug located in the rear car go area. 2. Fit the wrench tool over the drive nut. Use the wr ench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow you to pull the tire out from under the vehicle.
CAUTION! The winch mechanism is designed for use with the jack wrench tool only . Use of an air wrench or other power tools is not recommended and they can dam- age the winch.
4. T ilt the retainer at the end of the cable and pull it through the center of the wheel. Preparations For Jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas.
NOTE: Passengers should not remain in the vehicle while the vehicle is being jacked. Jacking Instructions W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
NOTE: Refer to the “Compact Spare T ire” section of the “T ires-General Information” under “Starting And Oper- ating” for information about the spar e tir e, it’s use, and operation. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle.
3. Loosen, but do not remove, the wheel bolts by turning them to the left one turn while the wheel is still on the ground. NOTE: • Ther e are front and rear jacking locations on each side of the bod.
4. T urn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable.
5. Using the swivel wr ench, raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability .
leverage. T ighten the wheel bolts in a star pattern until each bolt has been tightened twice. For the correct wheel bolt torque refer to T orque Specifications in this section. If in doubt about the correct tightness, have them checked with a torque wr ench by your autho- rized dealership or service station.
Road Tire Installation V ehicles Equipped W ith Wheel Covers 1. Mount the road tir e on the axle. 2. Install the spare wheel and hand start the wheel bolts. W ARNING! T o avoid the risk of forcing the vehicle off the jack, do not tighten the wheel bolts fully until the vehicle has been lowered.
6. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not use a hammer or excessive force to install the cover . V ehicles W ithout Wheel Covers 1. Mount the road tir e on the axle. 2. Install the remaining wheel bolts with the cone shaped end of the nut toward the wheel.
CAUTION! The winch mechanism is designed for use with the jack wrench extension tool only . Use of air wrench or power tool may damage the winch. JUMP-ST ARTING PROCEDURE If your vehicle has a discharged battery , it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack.
Preparations For Jump-Start The battery in your vehicle is located between the left front headlight assembly and the left fr ont wheel splash shield. Battery Posts 1 — Positive (+) Post (Covered W i.
W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. Y ou can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.
Jump-Starting Procedure W ARNING! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.
5. Start the engine in the vehicle that has the booster battery , let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery . 6. Once the engine is started, remove the jumper cables in the reverse sequence: Disconnecting The Jumper Cables 1.
and REVERSE (with automatic transmission) or 2nd gear and REVERSE (with manual transmission), while gently pressing the accelerator . Use the least amount of accel- erator pedal pressure that will maintain the rocking motion, without spinning the wheels, or racing the engine.
W ARNING! Fast spinning tires can be dangerous. Forces gener - ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires.
5. Insert a small screwdriver or similar tool into the access hole, and push and hold the override release lever in. 6. Move the shift lever to the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. 8. Reinstall the shift lever override access cover .
Proper towing or lifting equipment is r equired to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer ’s instructions.
CAUTION! • DO NOT flat tow any vehicle equipped with a conventional automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are OFF the ground. • T owing this vehicle in violation of the above re- quirements can cause severe transmission damage.
• Flash hazard lights as long as the battery has power or until the ignition key is turned off. • T urn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • Unlock the doors automatically .
5. T urn Right T urn Signal Switch ON. Right T urn Light is ON SOLID. Left T urn Light BLINKS. 6. T urn Left T urn Signal Switch ON. Left T urn Light is ON SOLID. Right T urn Light is ON SOLID. 7. T urn Left T urn Signal Switch OFF . (T urn Signal Switch Must be placed in Neutral State).
MAINT AINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMP AR TMENT — 1.4L ......... .347 䡵 ENGINE COMP AR TMENT — 1.4L TURBO . . . .348 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .349 ▫ Onboard Diagnostic System (OBD II) Cybersecurity ...............
▫ Brake System ....................... .374 ▫ Manual T ransmission — If Equipped ...... .377 ▫ Automatic T ransmission — If Equipped .... .377 ▫ Appearance Care And Pr otection From Corrosion .......................... .379 ▫ Convertible T op Care — If Equipped .
ENGINE COMP ARTMENT — 1.4L 1 — Engine Coolant Reservoir 5 — Battery 2 — Engine Oil Dipstick 6 — Air Cleaner Filter 3 — Brake Fluid Reservoir 7 — Engine Oil Fill 4 — Front Distribution .
ENGINE COMP ARTMENT — 1.4L TURBO 1 — Engine Coolant Reservoir 5 — Battery 2 — Engine Oil Dipstick 6 — Engine Oil Fill 3 — Brake Fluid Reservoir 7 — W asher Fluid Reservoir 4 — Front Di.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
access this information to assist with the diagnosis and service of your vehicle and emissions system. W ARNING! • ONL Y an authorized service technician should con- nect equipment to the OBD II connection port in order to diagnose or service your vehicle.
serviced, recently had a dead battery or a battery r eplace- ment. If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test. Y our vehicle has a simple ignition actuated test, which you can use prior to going to the test station.
Regardless of whether your vehicle’s OBD II system is ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running.
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may requir e servicing or replacement in the future.
after a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading.
recommends engine oils that are API Certified and meet the requir ements of FCA Material Standard MS-6395. Engine Oil Selection — 1.4L T urbo Engine For best performance and maximum protection under.
Lubricants which do not have both the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Engine Oil V iscosity — 1.4L T urbo Engine (SAE Grade) MOP AR SAE 5W -40 full synthetic engine oil is recom- mended for all operating temperatures.
indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer , service station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change.
Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably . Only high quality filters should be used to assure most efficient service. MOP AR engine air cleaner filters are a high quality filter and are recom- mended.
CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case.
CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the New V ehicle Limited W arranty .
The A/C air filter is located in the fr esh air inlet on the lower right of center console. Perform the following procedur e to replace the filter: 1. Remove the T orx scr ew that secur es the passenger side console closeout cover . 2. Pull the console closeout cover rearward to disengage the front retaining tab and remove the cover .
3. Remove the two 5.5 mm screws (1 and 2) that secure the particulate air filter cover to the HV AC housing. 4. Remove the A/C air filter by pulling it straight out of the housing. T ake note of the air filter position indica- tors. 5. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal.
CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter . Failure to properly install the filter will result in the need to replace it more often. 6. Install the passenger side console closeout. Refer to the “Maintenance Schedule” for the proper maintenance intervals.
Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to r emove salt or dirt from a dry windshield or rear window . A void using the wiper blades to remove frost or ice fr om the windshield or rear window .
NOTE: The rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder .
5. Lower the wiper blade and snap the pivot cap into place. Adding W asher Fluid The windshield washer fluid reservoir is located in the engine compartment, and the fluid level should be checked at regular intervals. Fill the reservoir with wind- shield washer solvent (not engine coolant/ antifreeze).
W ARNING! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, refer to “Safety T ips/Exhaust Gas” in “Things T o Know Before Starting Y our V ehicle” for further information.
Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
Refer to the “Maintenance Schedule” for the proper maintenance intervals. Selection Of Coolant Refer to “Fluids, Lubricants, And Genuine Parts” in “Maintaining Y our V ehicle” for further information.
Adding Coolant Y our vehicle has been built with an improved engine coolant (OA T coolant conforming to MS.90032) that al- lows extended maintenance intervals. This engine cool- ant (antifreeze) can be used up to ten years or 150,000 miles (240,000 km) before replacement.
• Some vehicles require special tools to add coolant properly . Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system, please contact your local authorized dealer .
Disposal Of Used Engine Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community .
• Do not overfill the coolant expansion bottle. • Check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freez- ing.
W ARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Riding the brakes may also reduce braking capacity in an emergency .
W ARNING! • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, And Genuine Parts” in “Maintaining Y our V ehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance.
CAUTION! Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transmis- sion. Manual T ransmission — If Equipped Lubricant Selection Use only the manufacturers recommended transmission fluid.
the transmission fluid at the correct level using the recommended fluid. No chemical flushes should be used in any transmission; only the approved lubricant should be used. CAUTION! Using a transmission fluid other than the manufac- turer ’ s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder .
transmission has no dipstick. Y our authorized dealer can check your transmission fluid level using special service tools. If you notice fluid leakage or transmission malfunc- tion, visit your authorized dealer immediately to have the transmission fluid level checked.
The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
Wheel And Wheel T rim Care • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • T o r emove heavy soil and/or excessive brake dust, use MOP AR Wheel Cleaner .
• For tough stains, apply MOP AR T otal Clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply MOP AR Multi-Purpose Cleaner to a clean, damp cloth and remove stain.
CAUTION! Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage. W ipe away immediately . CAUTION! Damage caused by these type of products may not be covered by your New V ehicle Limited W arranty .
equipped with radio antennas. Do not use scrapers or other sharp instrument that may scratch the elements. When cleaning the rear view mirr or , spray cleaner on the towel or cloth that you are using.
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water . Do not remove the belts from the vehicle to wash them.
CAUTION! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • A void high-pressure car washes, as they can dam- age the top material. Also, increased water pressure may force past the weather strips.
before washing the top. The top should be washed with a soft, natural bristle scrub brush, and a mild soap solution such as liquid dishwashing soap. Do not use detergent. CAUTION! Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic sol- vents, petroleum distillates, or plasticizers.
W ARNING! (Continued) • If the replaced fuse blows again, contact an autho- rized dealer . • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer .
Cavity V ehicle Fuse Num- ber Mini Fuse Description 3 F53 5 Amp T an Instrument Panel Node 4 F38 20 Amp Y ellow Central Door Locking 5 F36 10 Amp Red Diagnostic Socket, V ehicle Radio, Climate Control System 6 F43 20 Amp Y ellow Bi-Directional W asher 7 F48 20 Amp Y ellow Passenger Power W indow 8 F13 7.
Underhood Fuses The Front Distribution Unit is located on the right side of the engine compartment, next to the battery . T o access the fuses, press the release tabs and remove the cover . The ID number of the electrical component correspond- ing to each fuse can be found on the back of the cover .
Cavity Maxi Fuse Mini Fuse Description F01 60 Amp Blue – Body Controller F02 20 Amp Y ellow – Audio Amplifier F03 20 Amp Y ellow – Ignition Switch F04 40 Amp Orange – Anti-Lock Brake Pump F05 .
Cavity Maxi Fuse Mini Fuse Description F16 – 7.5 Amp Brown T ransmission F17 – 25 Amp Clear Powertrain (Multiair – If Equipped) F17 – 15 Amp Blue Powertrain F18 – 15 Amp Blue Powertrain F18 – 5 Amp T an Powertrain (Multiair – If Equipped) F19 – 7.
Cavity Maxi Fuse Mini Fuse Description F85 30 Amp Green – Rear Defroster F87 – 5 Amp T an Rear Defroster F90 – 5 Amp T an Heated Mirrors – If Equipped VEHICLE STORAGE If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery .
REPLACEMENT BULBS Interior Bulbs Bulb Number Overhead Lamp C5W Courtesy Lamp W5W Exterior Bulbs Bulb Number Front Low and High Beam Headlamp HIR2LL Front Parking/Daytime Running Lamps W21/5W Front Fog.
Bulb Number Rear T ail and Stop Lamps P21/5W Rear Backup Lamps W16W Center High Mounted Stop Lamp W5W License Plate Lamps LED (See Authorized dealer) NOTE: Numbers refer to commercial bulb types that can be purchased fr om your authorized dealer .
Front T urn Signal, Parking And Daytime Running Lamps 1. T urn the steering wheel completely to the left or right. 2. Open the wheel housing access door . 3. Remove the plastic cap from the back of the lamp housing. 4. Rotate bulb/socket counter-clockwise.
Front Fog Lamps T o replace the front fog lights, see your authorized dealer. Front/Rear Side Marker Lamps 1. Remove portion of the wheel liner to allow hand access to side marker lamp. 2. Rotate the bulb socket counterclockwise, and r emove the bulb and socket assembly from the housing.
3. Remove four screws and separate the backplate from the lamp housing. 4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 5. Remove the backup lamp bulb by pulling straight out. 6. Replace lamps as requir ed and reinstall lamp.
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 10.5 Gallons 40 Liters Engine Oil with Filter 1.4L/1.4L T urbo Engine 4 Quarts 3.8 Liters Cooling System 1.4L/1.4L T urbo Engine (MOP AR Antifreeze/Engine Coolant 10 Y ear/150,000 Mile Formula) — with Manual T ransmission 4.
FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant – 1.4L/1.4L T urbo Engine W e r ecommend you use MOP AR Antifreeze/Coolant 10 Y ear/150,000 Mile Formula OA T (Organic Additive T echnology) meeting the r equirements of FCA Material Standard MS.
Component Fluid, Lubricant, or Genuine Part Spark Plugs – 1.4L/1.4L T urbo Engine W e recommend you use MOP AR Spark Plugs. Fuel Selection – 1.4L/1.
Chassis Component Fluid, Lubricant, or Genuine Part Manual T ransmission – If Equipped W e recommend you use MOP AR C635 DDCT/MTX T ransmission Fluid Automatic T ransmission – If Equipped Use only MOP AR A W -1 Automatic T ransmission Fluid or equivalent.
I n f o r m a t i o n P r o v i d e d b y :.
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE ............ .406 ▫ Maintenance Chart ................... .408 8 I n f o r m a t i o n P r o v i d e d b y :.
MAINTENANCE SCHEDULE Y our vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate.
Once A Month Or Before A Long T rip: Check engine oil level. Check windshield washer fluid level. Check the tire inflation pressures and look for unusual wear or damage. Check the fluid levels of the coolant r eservoir and brake master cylinder , and fill as needed.
Maintenance Chart Refer to the Maintenance Schedules on the following pages for the requir ed maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 7.
Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or.
Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or.
W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
I n f o r m a t i o n P r o v i d e d b y :.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 SUGGESTIONS FOR OBT AINING SER VICE FOR YOUR VEHICLE ...................... .415 ▫ Prepar e For The Appointment ............ .415 ▫ Prepar e A List ....................... .415 ▫ Be Reasonable W ith Requests .
䡵 DEP AR TMENT OF TRANSPOR T A TION UNIFORM TIRE QUALITY GRADES ................ .421 ▫ T readwear .......................... .421 ▫ T raction Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you ar e having warranty work done, be sure to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner . This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process.
Puerto Rico And U.S. Virgin Islands Customer Service Chrysler International Services LLC P .O. Box 191857 San Juan 00919-1857 T el.: (787) 782-5757 Fax: (787) 782-3345 Customer Assistance For The Hear.
The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract.
REPORTING SAFETY DEFECTS In The 50 United States And W ashington, D.C. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying the manufacturer .
NOTE: A street address is requir ed when ordering manuals (no P .O. Boxes). Service Manuals These comprehensive Service Manuals provide the infor - mation that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintain- ing, servicing, and repairing FCA USA LLC vehicles.
DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following tir e grading categories were established by the National Highway T raffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
T emperature Grades The temperature grades are A (the highest), B, and C, repr esenting the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
Adding Engine Coolant (Antifreeze) ........... .371 Adding Fuel ............................ .301 Adding W asher Fluid ..................... .366 Additives, Fuel .......................... .298 A i r B a g .............................. .41, 42 Advance Front Air Bag .
Audio Systems (Radio) .................... .191 Automatic Dimming Mirror ................... 9 0 Automatic Oil Change Indicator .............. .406 Automatic T emperatur e Control (A TC) ......... .213 Automatic T ransaxle ........................ 1 2 Automatic T ransmission .
Caps, Filler Fuel ................................ .301 Oil (Engine) ................... .355, 356, 406 Carbon Monoxide W arning ............... .78, 300 Cargo Area Features ...................... .132 Car W ashes ............................ .380 Cellular Phone .
Contract, Service ......................... .417 Convertible T op Maintenance ................ .386 Coolant (Antifreeze) ................... .400, 401 Cooling System .......................... .369 Adding Coolant (Antifreeze) .............. .371 Coolant Capacity .
Electrical Power Outlets .................... .128 Electric Remote Mirrors ...................... 9 1 Electronic Brake Control System .............. .252 Brake Assist System .................... .254 Electronic Speed Control (Cruise Control) ........ 1 1 4 Electronic Stability Control (ESC) .
Euro T win Clutch T ransmission Fluid T ype ........................... .377 Event Data Recorder ........................ 5 6 Exhaust Gas Caution ................... .78, 300 Exhaust System ....................... .78, 366 Exterior Lights ............
Fueling ............................... .301 Fuses ................................. .388 Gas Cap (Fuel Filler Cap) ............... .301, 302 Gasoline, Clean Air ....................... .297 Gasoline (Fuel) ....................... .296, 400 Gasoline, Reformulated .
Interior Lighting ......................... .107 Introduction .............................. 4 Jacking Instructions ....................... .325 Jack Location ........................... .321 Jack Operation ....................... .320, 325 Jump Starting .
Service .............................. .396 T ire Pressur e Monitoring (TPMS) ........... .160 T raction Contr ol ....................... .260 T urn Signal ..................... .81, 106, 173 W arning (Instrument Cluster Description) . . .157, 173 Loading V ehicle T i r e s .
Occupant Restraints ........................ 2 8 Oil Change Indicator ...................... .180 Oil Change Indicator , Reset ................. .180 Oil, Engine ...................... .353, 400, 401 Capacity ......................... .400, 401 Change Interval .
Preparation For Jacking .................... .324 Pretensioners Seat Belts .............................. 3 8 Radial Ply T ires ......................... .276 Radio Frequency General Information .................. .15, 21 Radio Operation .............
Lap/Shoulder Belt Operation ................ 3 4 Lap/Shoulder Belts ....................... 3 2 Lap/Shoulder Belt Untwisting ............... 3 6 Pregnant W omen ........................ 3 8 Seat Belt Extender ....................... 3 7 Seat Belt Pretensioner .
Spark Plugs ............................ .401 Speed Control Accel/Decel ........................... 1 1 7 Speed Control (Cruise Control) ................ 1 1 4 Sport Mode ............................ .250 Starting ............................... .227 Automatic T ransmission .
Load Capacity ..................... .268, 270 Pressur e Monitor System (TPMS) ........... .287 Pressur e W arning Light .................. .160 Quality Grading ....................... .421 Radial .............................. .276 Replacement .......
Untwisting Procedur e, Seat Belt ................ 3 6 V ehicle Identification Number (VIN) ............. 7 V ehicle Loading ......................... .270 V ehicle Modifications/Alterations ............... 8 V ehicle Security Alarm Disarming .........
INST ALLA TION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel.
First Edition Printed in U .S.A. ©2015 FCA US LLC. All Rights Reser ved. FIA T is a registered trademark of Fiat Group Marketing & Corporate Communication S .p.A., used under license by FCA US LLC. 16FF500-126-AA I n f o r m a t i o n P r o v i d e d b y : 16FF500-126-AB Second Edition Rev.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Fiat 500c (2016) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Fiat 500c (2016) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Fiat 500c (2016), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Fiat 500c (2016) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Fiat 500c (2016), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Fiat 500c (2016).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Fiat 500c (2016). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Fiat 500c (2016) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
