Manuel d'utilisation / d'entretien du produit Converteon AT-CV5000- du fabricant Allied Telesis
Aller à la page of 114
613-000586 Rev. B CONVERTEON™ Family Media Converter Chassis AT-CV5000 Installation Guide.
Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part o f this pub lication may be repro duced without prior wr itten permission from Al lied Telesis, Inc. Allied Telesis is a t rademark of Allied Tele sis, Inc. Microsoft and Internet Explorer are regist ered tradem arks of Microsoft Co rporation.
3 Electrical Safety and Emissions S tandards This product meets the following standards. RFI Emissions FCC Class A, EN55022 Cl ass A, EN61000-3-2, EN61000-3-3, VCCI Class A, C-TICK, CE Immunity EN55024 Electrical Safety EN60950 (TUV), UL 60950 ( C UL US ) U.
4 T ranslated Safety S tatements Important: The indicates that a translation of th e safety statement is available in a PDF document titled “Translated Safety St atements” ( 613-000405) posted on the Allied Telesis website a t www.alliedtelesis.
5 Preface ...... .............. ........... ........... ............ .............. ........... ........... ........... ........... .............. . ............. ............ ........... ........... . 13 Safety Symbols Used in th is Docu ment........
Contents 6 Unpacking the Chassis . .............. ........... .............. ............ .............. ........... .............. .............. . .......... ........... .............. ........... 45 Installing the Power Cord Retaining Clip (AC Powered Ch assis Only).
AT-CV5000 Media Conve rter Chassis Installati on Guide 7 Using a Cartridge-Type Cleaner ........ ........... .............. .............. ............ .............. .............. .......... .................. ........... .......... 110 Using a Swab .
Contents 8.
9 Figure 1. AT-CV5000 Media Converte r ............. .......................................... .................................... ............ ........... ........... 18 Figure 2. Front Panel of the AT-CV5000 Chassis ................... ...........
Figures 10 Figure 51. Tightening the Captive Screw ............... ......... .............. ........... ........... ........... ........... ..... .... ........... .............. ....... 77 Figure 52. Resetting the AT-CV5M01 Management Card ... .......
11 Table 1. Safety Sy mbols ..................... .............. ........... .............. ........... .............. ............ ..... ......... ........... .............. ........... . 14 Table 2. Status LEDs on the LED Interface Car d ... .......
Tables 12.
13 Pr eface This guide contains instructions on ho w to install an AT-CV5000 Media Converter and the Converteon™ Serie s line cards. This preface contains the following sections: “Safety Symbo.
Preface 14 Safety Symbols Used in this Document This document uses the safety symbols defined in Table 1. T able 1. Safety Symbols Symbol Meaning Description Caution Performing or omi tting a specific action may result in equipment damage or loss of data.
AT-CV5000 Media Conve rter Chassis Installati on Guide 15 Where to Find Web-based Guides The installation and user guides for all Allied Telesis products are available in portable document format (PDF) o n our web site at www.alliedtelesis.com . You can view the documents onlin e or download them onto a local workstation or server.
Preface 16 Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate information . Online Support You can request technical sup port online by accessing t he Allied Telesis Knowledge Base: www.
17 Chapter 1 Overview This chapter contains the following sections: “A T -CV5 000 Overview” on p age 18 “System Description” on page 19 “Front and Rear Panel Component s” on pa.
Chapter 1: Ove rview 18 AT-CV5000 Overview The AT-CV5000 media converter, as sh own in F igure 1, is a modular unit that simplifies the task of building and maintain ing a Fast Ethernet or Gigabit Ethernet network.
AT-CV5000 Media Conve rter Chassis Installati on Guide 19 System Description Hardware Features The standard AT-CV5000 Media Conv erter chassis has the following features: 18 line card/exp ansion s.
Chapter 1: Ove rview 20 Front and Rear Panel Components Figure 2 shows the front panel of the AT -CV5000 chassis. Figure 2. Front Panel of the AT-CV5000 Ch assis Figure 3 illustrates the rear panel of the AT-CV5000 AC powered chassis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 21 LED Interface Card The LED interface card, as shown in Figu re 5, is preinstalled in the AT-CV5000 chassis and is not field -replaceable.
Chapter 1: Ove rview 22 Data bit s: 8 Parity: None St o p b i ts : 1 Flow control: None These default settings are for a DEC VT100 or ANSI terminal, or an equivalent terminal emulation program. Interface Card LEDs Table 1 lists the system status LEDs located on the LED interface card.
AT-CV5000 Media Conve rter Chassis Installati on Guide 23 RESET LINE/ EXP Button You can use the recessed RESET LINE/EXP button to reset the line cards and/or the module currently present in the expansion slot in the rear of the chassis. Note This reset button d oes not allow you to reset any managemen t cards in the chassis.
Chapter 1: Ove rview 24 AT-CV5M01 Management Card The AT-CV5M01 Management Card provides a CPU subsystem for the AT-CV5000 chassis as well as the AT-S7 0 management software preinstalled that allows you to con figure and monitor the status of the converter line cards.
AT-CV5000 Media Conve rter Chassis Installati on Guide 25 Parity: None S top bits: 1 Flow control: None These default settings are for a DEC VT100 or ANSI terminal, or an equivalent terminal emulation program.
Chapter 1: Ove rview 26 end node with a fixed duplex mode of f ull-duplex to a man agement card port, you should use the AT-S70 manageme nt software to disable Auto-Negotiation on the port a nd set the port speed and duplex mode manually. For 10 Mbps operation, Category 3 or b etter, 100 Ohm shielded or unshielded, twisted pair cabling is required.
AT-CV5000 Media Conve rter Chassis Installati on Guide 27 FD Green The twisted pa ir port is operating in full- duplex mode. OFF The twisted pa ir port is operating in half- duplex mode.
Chapter 1: Ove rview 28 Converteon™ Line Cards Note For a current list of line cards for the Converteon™ Series Chassis, refer to the Allied Telesis web site or consult your authorized sales representative.
AT-CV5000 Media Conve rter Chassis Installati on Guide 29 port has been lost. If the failure occurs on th e fiber optic cabling, the line card drops the link to the twisted p air port.
Chapter 1: Ove rview 30 Blank Slot Covers The AT-CV5PNLx Series blank slot covers are designed to maintain optimal, trouble-free environmental conditions for the modules used in the Converteon™ AT-CV5000 chassis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 31 Power Supplies The AT-CV5000 chassis is shipped with two rear slots d esignated for the power supplies.
Chapter 1: Ove rview 32 Fan Modules The AT-CVFAN module, as shown in Figure 10, is d esigned for use with the AT-CV5000 chassis. You can install the same fan module in either fan slot labeled A or B, located at the rear of the AT-CV5000 chassis. Fo r proper operation, two AT-CVFAN modules are prein stalled in the AT-CV5000 chassis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 33 Management Connections The AT-CV5000 chassis provides two ports to conn ect to the AT-S70 management software: For local management, connect to the RS-232 terminal port on the A T-CV5M01 Management Card or to the RS-232 con sole port on the A T-CM70S line card only .
Chapter 1: Ove rview 34 A Few Basics about Media Converters An Ethernet media converter can in terconnect network devices over large distances by transferring Ethernet tr affic between twisted pair ports and fiber optic cabling.
AT-CV5000 Media Conve rter Chassis Installati on Guide 35 with an end node, the end nod e should also be using Auto-Negotiation. Otherwise, a duplex mode mismatch can occur. A line card port, using Auto-Negotiation, defaults to half -duplex if it detects that the end node is not using Auto-Negotiation.
Chapter 1: Ove rview 36 Network Topologies This section discusses the network topologies you ca n create with the Converteon™ Fast and Gigabit Med ia Converter Line Cards. Standalone Topology Figure 12 illustrates a standalone topology using one AT-CV5000 media converter with an AT-CM202 line card to int erconnect two small networks.
AT-CV5000 Media Conve rter Chassis Installati on Guide 37 Network 1 has an A T -8350GB switch connected to the 10/100Base-TX port on the A T -CM202 line card in the first A T -C5000 media converter .
Chapter 1: Ove rview 38.
39 Chapter 2 Installation This chapter contains the following insta llation procedures f or the AT-CV5000 chassis: “Reviewing Safety Precautions” on p age 40 “Selecting a Site for the Ch.
Chapter 2: Inst allation 40 Reviewing Safety Precautions Please review the following safety pr ecautions before you begin to install the switch. Note The indicates that a translation of the safety state ment is available in a PDF document titled “Tra nslated Safety Statements” (613-000405) on the Allied Telesis website a t www.
AT-CV5000 Media Conve rter Chassis Installati on Guide 41 W arning: As a safety precaution, inst all a circuit breaker with a minimum value of 15 Amps between the equipment and the DC power source. Always connect the wires to the LAN equip ment first before you connect the wires to the circuit breaker .
Chapter 2: Inst allation 42 Caution: Risk of explosion if battery is replace d by an incorrect type. Replace only with the same or equivalent type recommended by the manufact urer. Dispose of used batteries according to the manufacturer’s instruction s.
AT-CV5000 Media Conve rter Chassis Installati on Guide 43 Warning: Reliable earthing of ra ck-mounted equipment should be maintained. Particular attention shou ld be given to supply connections other than direct connec tions to the branch circuits (e.
Chapter 2: Inst allation 44 Selecting a Site for the Chassis Observe the following requirements w hen choosing a site for the ch assis: If you plan to inst all the chassis in an equip ment rack, check to be sure that the rack is safely secured and that it will no t tip over .
AT-CV5000 Media Conve rter Chassis Installati on Guide 45 Unpacking the Chassis To unpack the chassis, perform the fo llowing procedure: 1. Remove all components from the shipping package. Note Store the packaging material in a safe location. You must use the original shipping material if you need t o return the unit to Allied Telesis.
Chapter 2: Inst allation 46 Installing the Power Cord Retainin g Clip (AC Powered Chassis Only) To install the power cord retaining clip o n an AT-CV5000 chassis with an AT-PWR14 AC power supply, perform the following procedure: 1. Locate the power cord retaining clip which is shown in Figure 14.
AT-CV5000 Media Conve rter Chassis Installati on Guide 47 4. Verify that the retaining clip is in the correct po sition, as shown in Figure 17. Figure 17. Retaining Clip Pro perly Installed in the Bracket P O WER F AU LT A T -PWR1 4 A A T-CVF AN A 100-240VA C ~ WARNING T h is u n it m ig h t h a v e m o re th a n o n e p o w e r in p u t .
Chapter 2: Inst allation 48 Installing the AT-CV5000 Chassis in a Rack The chassis is shipped with two ra ck-mounting brackets. To mount the chassis in a rack, perform the following procedure: 1.
AT-CV5000 Media Conve rter Chassis Installati on Guide 49 Warning: Operating Temperature. This product is designed for a maximum ambient temperature of 40° deg rees C. E7 All Countries: Install product in accordance with loca l and National Electrical Codes.
Chapter 2: Inst allation 50 Grounding the AT-CV5000 Chassis To ensure the safe and proper operation of your AT-CV500 0 chassis, you must ground the unit to a ground po int using either of the frame groun d connectors on the rear panel, as sho wn in Figure 20.
AT-CV5000 Media Conve rter Chassis Installati on Guide 51 The frame ground stud for po wer supply A is shown in Fig ure 22. Figure 22. Placing the Ground Lug on the Frame Ground Stud 4. Secure the ground lug with the lock nut you remo ved in Step 2, as shown in Figure 23.
Chapter 2: Inst allation 52 Installing a Converteon™ Line Card To install a Converteon™ line card, perf orm the following procedure: Note The Converteon™ line cards can be installed in any line card slots located in the front panel of the AT-CV5000 ch assis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 53 5. Locate the top and bottom alignment guides inside th e line card slots, as shown in Figure 24. Figure 24. Location of the Alignmen t Guides 6. Align the line card with the top and bo ttom alignment guides loca ted inside the slot.
Chapter 2: Inst allation 54 8. Use a Phillips screwdriver to tight en the captive screw on the line card, as shown in Figure 26. Figure 26. Tightening the Captive Scre w Note Always tighten the captive screw to secure the line card to the chassis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 55 Cabling a Converteon™ Line Ca rd in an AT-CV5000 Chassis Perform the following procedures to co nnect to the ports that come with the line cards an d/or other modules.
Chapter 2: Inst allation 56 connector is connected to the receiver conn ector on the remote nod e. Figure 27. Dual SC Port To connect a fiber optic cable to a dual SC connector, perform the following procedure: 1. Remove the dust cover from the fiber optic port, as shown in Figure 28.
AT-CV5000 Media Conve rter Chassis Installati on Guide 57 5. When the connection is establish ed, the LK LED for the fiber optic port should show green.
Chapter 2: Inst allation 58 Cabling a Twisted Pair Port When you connect a twisted pair cabl e to a port, observe the following guidelines: An RJ-45 connector should fit snu gly into the port on the con verter . The tab on the conne ctor should lock the connector into place.
AT-CV5000 Media Conve rter Chassis Installati on Guide 59 in Figure 33. Figure 33. Inserting an SFP Transceiver into the SFP Slot Note For information about the proper cable typ e, refer to the SFP transceiver installatio n instructions.
Chapter 2: Inst allation 60 Powering On an AC Powered Chassis This section describes how to power on an AC po wered AT-CV5000 chassis. If your chassis is DC power ed, see “Powering On a DC Powered Chassis” on page 64. Note The AT-CV5000 chassis is shipped without any power supplies installed.
AT-CV5000 Media Conve rter Chassis Installati on Guide 61 2. Position the power cord retaining clip in the up positio n, as shown in Figure 37. Figure 37. Power Cord Retaining Clip in the Up Position 3. Select the power plug that is correct for your region: North America, UK, Europe, or Australia.
Chapter 2: Inst allation 62 6. Turn the ON/OFF power switch of the installed power supply module to the ON position, as shown in Figure 40. Figure 40. ON/OFF Power Switch in ON Position 7.
AT-CV5000 Media Conve rter Chassis Installati on Guide 63 default parameter settings of the chassis, which are listed in the AT-S70 Management Software User’s Guide .
Chapter 2: Inst allation 64 Powering On a DC Powered Chassis This section describes how to power on a DC powered AT-CV5000 chassis. If your chass is is AC powe red, se e “Powering On an AC Powered Chassis” on page 60. For inf ormation about how to install the power supply, refer to “Installing an AT-PWR15 DC Powe r Supply” on page 84.
AT-CV5000 Media Conve rter Chassis Installati on Guide 65 4. With a 14-gauge wire-stripping tool, strip the three wires in the tray cable coming from the DC input po wer source to 8mm ± 1mm (0.31 in., ± 0.039 in.), as shown in Figure 42 o n page 65.
Chapter 2: Inst allation 66 Figure 43. Inserting Wires into a DC Terminal Block 6. Connect the +48 VDC (RTN) feed wire to the terminal block marked + (plus).
AT-CV5000 Media Conve rter Chassis Installati on Guide 67 Starting a Local Management Session The procedure in this section explains how to start a local management session using the RS-232 terminal port on an AT-CV5M01 Management Card or the 8-pin Mini-DIN port on an AT-CM70 S line card installed in the chassis.
Chapter 2: Inst allation 68 on an AT-CM70S Line Card 2. Connect the other end of the cable to an RS-232 p ort on a terminal or a personal computer with a terminal emulation program.
AT-CV5000 Media Conve rter Chassis Installati on Guide 69 Refer to the AT-S70 Management Software User’s Guide for in formation about how to move through the men us and make menu selections.
Chapter 2: Inst allation 70 Starting a Remote Management Session The procedure in this sectio n explains how to start a remote management session using the 10/100Base-TX port on the AT-CV5M01 Manage ment Card on the chassis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 71 Usernames and passwords are case-sensitive. Refer to the AT-S70 Management Software User’s Guide for in formation about how to move through the men us and make menu selections.
Chapter 2: Inst allation 72.
73 Chapter 3 W orking with Line Cards and other Modules This chapter contains the following in sta llation procedures f or line cards and other modules in the AT-CV5000 chassis: “Removing a Conv.
Chapter 3: Workin g with Line Cards and oth er Modules 74 Removing a Converteon™ Line Card To remove a Converteon™ line card, perform the follo wing procedure: Caution Be sure to observe all standard electrosta tic discharge (ESD) precautions, such as wearing a n antistatic wrist strap, to avoid damaging the device.
AT-CV5000 Media Conve rter Chassis Installati on Guide 75 Note The blank slot cover prevents du st from getting into the chassis and maintains proper airflow, cooling, and ventilation thr oughout the chassis.
Chapter 3: Workin g with Line Cards and oth er Modules 76 Working with the AT-CV5M01 Management Card This section contains the following proced ures: “Installing an A T-CV5M01 Management Card,.
AT-CV5000 Media Conve rter Chassis Installati on Guide 77 4. Slide the management card into the slot, as shown in Figure 50 , until the front of the card is flush with the front of the chassis.
Chapter 3: Workin g with Line Cards and oth er Modules 78 Note This CPU RESET resets only the management card, and does not reset the line cards and/or the module installed in the expansion slot at the rear of the chassis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 79 Installing an AT-CM70S Line Card The AT-CM70S line card is a double-slot line card that takes up two line card slots in the chassis. Therefore, the process for installing this ca rd differs slightly from the process for installing other Converteon™ line cards.
Chapter 3: Workin g with Line Cards and oth er Modules 80 6. Slide the AT-CM70S line card into the two slo ts, as shown in Figure 53, until the line card is flush with the front of the chassis. Figure 53. Inserting an AT-CM70S Line Card 7. Use a Phillips screwdriver to tight en the captive screw on the line card, as shown in Figure 54.
AT-CV5000 Media Conve rter Chassis Installati on Guide 81 Resetting the Line Cards and the Module in the Rear Expansion Slot To reset the line cards and th e module in the rear expansion slo t, perform the following procedure: 1. Locate the RESET LINE/EXP button, which is recessed on the front panel of the LED interface card.
Chapter 3: Workin g with Line Cards and oth er Modules 82 Installing an AT-PWR14 AC Power Supply The AT-CV5000 chassis is shipped with two slots in the rear designated for the power supplies, but without any power su pplies installed. You must install at least one power supply in orde r to power on the cha ssis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 83 5. Slide the AT-PWR14 power supply into the selected slot, as shown in Figure 56, until the module is flush with the front of the chassis.
Chapter 3: Workin g with Line Cards and oth er Modules 84 Installing an AT-PWR15 DC Power Supply The AT-CV5000 chassis is shipped with two slots in the rear designated for the power supplies, but without any power su pplies installed. You must install at least one power supply in orde r to power on the cha ssis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 85 5. Slide the AT-PWR15 DC power supply into the selected slot, as shown in Figure 58, until the module is flush with the fro nt of the chassis. Figure 58. Inserting the AT-PWR15 DC Power Supply 6.
Chapter 3: Workin g with Line Cards and oth er Modules 86 Replacing an AT-CVFAN Module This section provides instructions for replacing an AT-CVFAN fan module if one fails. Caution For normal operation, the chassis must have two operation al fans. Caution The AT-CVFAN modules are field-replaceable; however, t hey are not hot-swappable.
AT-CV5000 Media Conve rter Chassis Installati on Guide 87 3. Pull the loosened screws to slide the fan out of the chassis, as sh own in Figure 60 or Figure 61. Figure 60. Removing an AT-CVFAN Module from Fan Slot A Figure 61. Removing an AT-CVFAN Module from Fan Slot B 4.
Chapter 3: Workin g with Line Cards and oth er Modules 88 a. To install a new fan in slot A, turn the fan so that the handle is on the left and slide the new fan module into the fan slot, as shown in Figure 62. Figure 62. Inserting an AT-CVFAN Module into Fan Slot A b.
AT-CV5000 Media Conve rter Chassis Installati on Guide 89 Figure 65. Tightening the Scre ws on the AT-CVFAN Module in Slot B T o power on the chassis, proceed to the proce dure described in “Powering On an AC Powered Chassis” on pag e 60 or “Powering On a DC Powered Chassis” on page 64 .
Chapter 3: Workin g with Line Cards and oth er Modules 90 Installing a Blank Slot Cover If any of the line card or expansion slo ts in the Converteon™ chassis is unoccupied, it must be covered with a blank slot cover, to keep dust from getting into the chassis and to mainta in proper airflow, cooling, a nd ventilation throughout the chassis.
AT-CV5000 Media Conve rter Chassis Installati on Guide 91 7. Slide the blank slot cover into the slot, as shown in Figure 66, until the slot cover is flush with the front of the chassis. Figure 66. Inserting an AT-CV5PNL1 Blank Slot Cover 8. Use a Phillips screwdriver to tighten the captive screw, as shown in Figure 67.
Chapter 3: Workin g with Line Cards and oth er Modules 92 Installing an AT-CV5PNL2 Blank Slot Cover The AT-CV5PNL2 blank slot cover is designed to cover any unoccupied power supply module slots in the AT-CV5000 ch assis model only. To install an AT-CV5PNL2 blank slot cover, perform the following procedure: 1.
AT-CV5000 Media Conve rter Chassis Installati on Guide 93 Note Always tighten the captive screws to secure the blank slo t cover to the chassis. Installing an AT-CV5PNL3 Blank Slot Cover The AT-CV5PNL3 blank slot cove r is designed to cover th e unoccupied expansion slot located in the rear of the AT-CV5000 chassis.
Chapter 3: Workin g with Line Cards and oth er Modules 94 4. Use a Phillips screwdriver to tight en the captive screws, as shown in Figure 71. Figure 71. Tightening the Captive Screws on an AT-CV5PNL3 Note Always tighten the captive screws to secure the blank slot cover to the chassis.
95 Chapter 4 T r oubleshooting This chapter contains informat ion about how to troubleshoot th e chassis and line cards in the even t that a problem occurs. Note If after following the instructions in this chapte r you are unable to resolve the problem, contact Allied Telesis Technical Support for assistance.
Chapter 4: Tro ubleshooting 96 Caution For normal operation, both fans mu st be installed in the chassis..
AT-CV5000 Media Conve rter Chassis Installati on Guide 97 AT-CV5M01 Management Card PWR LED is OFF If the PWR LED on an AT-CV5M01 card is OFF, p erform the following: If the chassis is installed o.
Chapter 4: Tro ubleshooting 98 FLT LED is Steadily ON If the converter FLT LED is steadily on, a problem has occurred in the converter, perform the following: T ry resetting the converter by di sconnecting and reconnecting the AC power cord.
AT-CV5000 Media Conve rter Chassis Installati on Guide 99 V erify that the end node connected to the port is ON and is operating properly . Check that the fiber optic cable is securely connected to the fiber optic port on the media converter and on the end node.
Chapter 4: Tro ubleshooting 100.
101 Appendix A T echnical Specifications Physical Specifications Dimensions (W x D x H) 34.25 cm x 44.05 cm x 8.68 cm (13.49 in x 17.35 in x 3.42 in) Weight: 6.
Appendix A: Technica l Specifications 102 Safety and Electromagnetic Emissions Certifications EMI: FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CE Immunity: EN55024 Safety: UL60950-1 ( C UL US ), EN60950-1 (TUV), CAN/CSA C22.2 No. 60950-1 Laser: EN60825 Quality and Reliability: MTBF > 100,000 hrs.
AT-CV5000 Media Conve rter Chassis Installati on Guide 103 RJ-45 Twisted Pair Port Pinouts Figure 72 illustrates the pin lay out for an RJ-45 connector an d port. Figure 72. RJ-45 Connector and Port Pin L ayout Table 3 lists the RJ-45 pin sign als when a twisted pair port is ope rating in the MDI configuration at 10 or 100 Mbps.
Appendix A: Technica l Specifications 104 RS-232 Terminal Port Pinouts Figure 72 illustrates the pin layout to a n RS-232 terminal port. Figure 73. RS-232 Terminal Port Pinou ts Table 5 lists the pin signals on the RS-232 Terminal Port.
AT-CV5000 Media Conve rter Chassis Installati on Guide 105 8-Pin Mini-DIN Console Port Pinouts Figure 74 illustrates the pin layout of the 8 -Pin Mini-DIN console port and connector. Figure 74. 8-Pin Mini-DIN Consol e Port and Conn ector Pin Layouts Table 6 lists the definitions for the 8-Pin Mini-DIN console port pinouts.
Appendix A: Technica l Specifications 106 SC Type Connectors Dual SC Connector The fiber optic cable, as shown in Figure 75, is used to connect to the dual SC connectors in various Converteon™ line cards.
AT-CV5000 Media Conve rter Chassis Installati on Guide 107 Dual ST Type Connector Cable The fiber optic cable, shown in Figure 77, is used to connect to the dual ST connectors in various Converteon™ line cards.
Appendix A: Technica l Specifications 108 SFP Transceiver Cable The SFP transceiver, as shown in Figure 78, is used in various Converteon™ line cards. Figure 78. SFP Transceiver The fiber optic cable, shown in Figure 79, is one of the cable types that can be used to connect to the SFP transceiver.
109 Appendix B Cleaning Fiber Optic Connectors The fiber optic connector consists of a fib er optic plug and its adapter. The end of the fiber optic cable is h eld in the core of the ferrule in the plug. Light signals are transmitted through the core of t he fiber.
Appendix B: Cleaning Fi ber Optic Connectors 110 Using a Cartridge-Type Cleaner Fiber optic cartridge cleaners are av ailable from many vendors and are typically called “cartridge cleaners,” as shown in Figu re 82. Figure 82. Cartridge Cleane r Note Do not use compressed air or aerosol air to clean a f iber optic connector.
AT-CV5000 Media Conve rter Chassis Installati on Guide 111 3. When you reach the end of the cleaning surface, pick up the ferrule tip, rotate and place it at the top and rub downwards a t least 2 times.
Appendix B: Cleaning Fi ber Optic Connectors 112 Using a Swab Specially treated swabs (stick cleaners) a re available for cleanin g inside connector adapters or hard-to- reach ferrule tips. These swabs, often referred to as “lint free” or “alcohol free” swabs, are available from many vendors, as shown in Figure 84.
AT-CV5000 Media Conve rter Chassis Installati on Guide 113 3. If a fiber inspection scope is available, u se the scope to inspect the connector to make sure that it is clean and to check for scratches, pits, or other problems that may aff ect performance.
Appendix B: Cleaning Fi ber Optic Connectors 114.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Allied Telesis Converteon AT-CV5000- c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Allied Telesis Converteon AT-CV5000- - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Allied Telesis Converteon AT-CV5000-, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Allied Telesis Converteon AT-CV5000- va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Allied Telesis Converteon AT-CV5000-, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Allied Telesis Converteon AT-CV5000-.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Allied Telesis Converteon AT-CV5000-. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Allied Telesis Converteon AT-CV5000- ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
