Manuel d'utilisation / d'entretien du produit M216KASPC du fabricant Exmark
Aller à la page of 32
For Serial Nos. 440,000 & Higher M216KASPC CONGRA TULA TIONS on the purchase of your new Exmark mower . This product has been carefully designed and manufactured to give you a maximum amount of dependability and years of trouble–free operation.
IMPORT ANT When the mower is used or operated on any California forest-, brush- or grass-covered land, a working spark arrester must be attached to the muffler . If not, the operator is violating state law , Section 4442 Public Resource Code. T o acquire a spark arrester for your unit, see your Engine Service Dealer .
iii EXMARK P AR TS PLUS PROGRAM EFFECTIVE DA TE: September 1,1995 Program If your Exmark dealer does not have the Exmark part in stock, Exmark will get the parts to the dealer the next business day or the part will be FREE* Guaranteed!! How the Program Works 1.
iv CONGRA TULA TIONS on the purchase of your Exmark Mower . This product has been carefully designed and manufactured to give you a maximum amount of dependability and years of trouble-free operation. OPERA T OR’S MANUAL This manual contains assembly , operating, maintenance, adjustment and safety instructions for your Exmark mower .
1 All Rights Reserved Printed in the USA Contents Page Specifications 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety 2 . . . . . . . . . . . . . . .
2 Introduction Read this manual carefully to learn how to operate and maintain your product properly . The information in this manual can help you and others avoid injury and product damage. Although Exmark designs and produces safe products, you are responsible for operating the product properly and safely .
3 • Do not operate the lawn mower when barefoot or wearing open sandals. • Always wear safety goggles or safety glasses with side shields when operating the lawn mower . • W arning: Gasoline is highly flammable. T ake the following precautions: – Store fuel in containers specifically designed for this purpose.
4 • W atch for holes, ruts, or bumps. T all grass can hide obstacles. • Do not mow near drop-offs, ditches, or embankments. Y ou could lose your footing or balance.
5 43-8480 52-2620 68-7410 74-1970 1. T ransmission speeds 2. Neutral 76-21 10 93-7398 100-3282 104-1329.
6 Assembly Note: Determine the left and right sides of the machine from the normal operating position. Installing the Handle 1. Mount the handle to the outside of the lawn mower housing (using the bottom hole) with 2 cap screws (5/16–18 x 1–1/4 in.
7 Installing the Discharge T unnel Plug 1. Open the dischar ge door by pulling forward on the handle and moving it rearward (Fig. 4). Hold the discharge door handle to prevent the spring-loaded door from closing while you insert the plug. m-1914 2 1 Figure 4 1.
8 Important Do not overfill the crankcase with oil and run the engine; engine damage will result. Drain the excess oil until the oil level on the dipstick reads Full. 8. Insert the dipstick into the filler neck and rotate the cap clockwise until it is tight.
9 3. Fill the fuel tank with unleaded gasoline to within 1/4 to 1/2 inch (6 to 13 mm) from the top of the tank. Do not fill into the filler neck. Important Do not fill the tank more than 1/4 inch (6 mm) from the top of the tank because the gasoline must have room to expand.
10 Operating the Blade and the Self-Propel Drive 1. Have the blade control bail in the A position (Fig. 1 1). m-3769 A B C Figure 1 1 2. Slide the blade control bail to the right and raise it to the B position to engage the blade (Fig. 1 1). 3. Squeeze the blade control bail against the handle to the C position to drive (Fig.
11 8. Move the blade control bail to the right and then lift it up to about one inch (2.5 cm) below the handle; refer to position A in Figure 14. Note: The fan-like noise indicates that the lawn mower blade is turning. 1 A B m-5085 Figure 14 1. 1 in. (2.
12 2. Release the wheel height adjustment lever and seat it securely in the notch. 3. Adjust all the wheels to the same cutting height setting. Using the Grass Bag Occasionally, you may wish to use the grass bag for bagging extra long grass, lush grass, or leaves.
13 Operating Tips • Review the safety instructions and read this manual carefully before operating the lawn mower . • Clear the area of sticks, stones, wire, branches, and other debris that the blade could hit and throw . • Keep everyone, especially children and pets, away from the area of operation.
14 Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Interval Maintenance Procedure Each Use • Check the engine oil level. • Check the stopping time of the blade brake.
15 Checking the Engine Oil Level Before you use the lawn mower , make sure that the oil level is between the Add and the Full marks as shown on the dipstick (Fig. 6). If the oil level is below the Add mark, and oil. Refer to Filling the Crankcase with Oil on page 7.
16 Cleaning the Discharge T unnel and Plug Remove the plug from the discharge tunnel and clean it after each use. Always be sure that the discharge tunnel door closes securely when you release the handle. If the debris prevents the dischar ge door from closing securely , clean the inside of the discharge tunnel and the door thoroughly .
17 6. Raise the left side of the lawn mower to drain the oil into the drain pan. Note: Y ou can also remove the oil from the crankcase using an oil extractor . 7. Lower the left side of the lawn mower . 8. Insert the dipstick into the filler neck and rotate the cap clockwise until it is tight.
18 Sharpening the Blade File the top side of the blade to maintain its original cutting angle (Fig. 25A) and inner cutting edge radius (Fig. 25B). The blade will remain balanced if you remove the same amount of material from both cutting edges. 153 1 m-4783 2 AB Figure 25 1.
19 8. Install the BBC shield. Rotate the tabs 180 back into position. Tighten the nuts or the bolts on tabs to secure the BBC shield to the deck. 9. Install the blade, the accelerator , the anti-scalp cup, and the two blade nuts. 10. Turn the lawn mower upright.
20 Adjusting the Self-propel Drive If the lawn mower does not self-propel or has a tendency to creep forward when the control bar is more than 1-1/2 inches (3.8 cm) from the handle, adjust the wheel drive control knob on the rear of the gear box. 1. Close the door in the lawn mower housing and remove the grass bag.
21 Oil may be hot after the engine has been run, and contact with hot oil can cause sever personal injury . A void contacting the hot engine oil when you drain it. W arning 2. Stop the engine and wait for all moving parts to stop. 3. Disconnect the wire from the spark plug (Fig.
22 3. Loosen the cable clamp screw until the cable conduit slides (Fig. 36). 278 1 2 3 Figure 36 1. Spring 2. Cable clamp screw 3. Cable conduit 4. Pull the cable to remove the slack, but do not put tension on the spring. 5. Tighten the screw to lock the adjustment in place.
23 Preparing the Fuel System Gasoline can vaporize if you store it over long periods of time and explode if it comes into contact with an open flame. • Do not store gasoline over long periods of time. • Do not stor e the lawn mower with gasoline in the fuel tank or the carburetor in an enclosur e with an open flame.
24 T roubleshooting Exmark designed and built your lawn mower for trouble-free operation. Check the following components and items carefully, and refer to Maintenance on page 14 for more information. If a problem continues, contact an Authorized Service Dealer .
25 Problem Corrective Action Possible Causes Lawn mower or engine vibrates excessively 1. The blade is bent or is out of balance. 2. The blade mounting bolt is loose. 3. The underside of the lawn mower deck contains clippings and debris. 4. The engine mounting bolts are loose.
Limited W arranty Exmark T urf Equipment Conditions and Products Covered Exmark Mfg. Co. Inc. and its af filiate, Exmark Warranty Company , pursuant to an agreement between them, jointly warrant o.
Date Description W ork Done Service Done By SERVICE RECORD.
SEE EXMARK’S COMPLETE LINE OF PRODUCTS FOR TURF CARE LAZER Z LAZER Z HP LAZER Z XP LAZER Z CT TURF RANGER TURF TRACER TURF TRACER HP VIKING HYDRO METRO METRO HP U.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Exmark M216KASPC c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Exmark M216KASPC - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Exmark M216KASPC, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Exmark M216KASPC va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Exmark M216KASPC, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Exmark M216KASPC.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Exmark M216KASPC. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Exmark M216KASPC ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
