Manuel d'utilisation / d'entretien du produit 4500-358 du fabricant Exmark
Aller à la page of 48
TURF TRACER ® HP For Serial Nos. 790,000 & Higher Part No. 4500-358 Rev . A.
W ARNING CALIFORNIA Proposition 65 W ar ning The engine exhaust from this product contains chemicals known to the State of Califor nia to cause cancer , birth defects, or other reproductiv e har m.
Introduction CONGRATULATIONS on the purchase of y our Exmark Mow er . T his product has been carefully designed and manufactured to giv e you a maximum amount of dependability and years of trouble-free operation. This manual contains operating, maintenance, adjustment, and safety instr uctions for your Exmark mow er .
Contents Introduction .. . . .. . . .. . . .. . . .. . . .. . . .. . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. 3 Safety .. . . .. . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . . .. . . .. . . .. . . .. . . .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1.
Safety DANGER In certain conditions gasoline is extremely ammable and v apors are explosi v e. A re or explosion from gasoline can bur n y ou, others, and cause proper ty damage. • Fill the fuel tank outdoors in an open area, when the engine is cold.
Safety Operation W ARNING Operating engine par ts, especially the mufer, become extremely hot. Sev ere bur ns can occur on contact and debris, such as leav es, grass, br ush, etc. can catch re. • Allow engine parts, especially the mufer, to cool before touching .
Safety DANGER Operating on w et grass or steep slopes can cause sliding and loss of control. Loss of control and/or loss of operator’ s footing could result in a fall with an ar m or leg getting under the mow er or engine deck which may result in serious injur y , death or drowning .
Safety W ARNING Hydraulic uid escaping under pressure can penetrate skin and cause injur y . Fluid accidentally injected into the skin must be surgically remov ed within a few hours by a doctor familiar with this for m of injur y or gangr ene may result.
Safety Safety and Instructional Decals • Keep all safety signs legible . R emov e all grease, dirt and debris from safety signs and instructional labels . • R eplace all w or n, damaged, or missing safety signs . • When replacement components are installed, be sure that cur rent safety signs are afx ed to the replaced components .
Safety 1-413327 48 inch and 52 inch Decks Only 1-413421 1-513747 19 HP Kawasaki Electric Start Only 1-553049 98-5954 103-1798 103-1976 19 HP Kawasaki Electric Start 1 1.
Safety 103-1977 15 HP and 17 HP Kawasaki Manual Start 103-2076 103-2103 103-2242 103-2243 103-4935 12.
Safety 109-3148 1 16-0404 13.
Specications Specications Model Numbers Serial Nos: 790,000 and Higher Manual Start Models: THP15KA363; THP17KA483; THP17KA523; THP17KA363CA; THP17KA483CA Electric Start Models: THP19KAE483; THP.
Specications Tires & Wheels Driv e Front Caster Pneumatic (Air-Filled) Pneumatic (Air-Filled) Semi- Pneumatic 36 48 & 52 All Decks Quantity 2 2 2 T read T urf Master T urf Master Smooth Size 16 x 6.
Product Overview T orque Requirements Bolt Location T orque Cutter Housing Spindle Nut 140-145 ft-lb (190-197 N-m) Blade Mounting Bolt (lubricate with anti-seize) 55-60 ft-lb (75-81 N-m) Engine Deck/M.
Operation Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Controls Operator Presence Control (OPC) Levers Located on the upper handle assembly directly abov e the handle grips. When these lev ers are depressed, the OPC system senses that the operator is in the nor mal operator’ s position.
Operation Park Brake Lever Located on the left side of the unit abo ve the hy draulic tank. The brak e lever engag es the park brake on the dri ve wheels . Pull the lev er up and rearward to engag e the brak e . Push the lev er forw ard and down to disengag e the brake .
Operation Pre-Start Fill fuel tanks . F or best results use only clean, fresh regular grade unleaded gasoline with an octane rating of 87 or higher . R egular grade leaded gasoline ma y also be used; ho wev er, combustion c hamber and cylinder head will require more frequent ser vice.
Operation PTO Engagement DANGER The rotating blades under the mow er deck are dangerous. Blade contact can cause serious injur y or kill y ou. Do Not put hands or feet under the mow er or mower deck when the blades are engaged. DANGER An unco v ered discharge opening will allo w objects to be thrown in an operator’s or bystander’s direction.
Operation Figure 5 1. Drive Lever in neutral position 3. Drive Lever in forward position 2. Drive Lever locked in neutral position 4. Drive Lever in reverse position Driving F orw ard 1. R elease the parking brak e. 2. With driv e lev ers loc ked in “neutral”, shift speed control lev er to desired forw ard speed.
Operation Figure 6 1. Deck support pin 2. Cutting Height B . The tire pressures are set as directed in Check Tire Pressures in the Maintenance section. C. The length of the rear dec k support link assemblies a verage 6.89 inc hes (appro ximately 6 7/8 inc hes) (175.
Operation Figure 8 For cutting heights above 3.5 inches (38 mm) use the bottom hole. The rollers will still be effective against scalping. 1. Anti-scalp roller mounting bracket 2. Cutting height 7. T or que the 3/8–16 whizloc k nut to 30-35 ft-lb (41-47 N-m) (Figure 9).
Maintenance Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Maintenance Ser vice Inter v al Maintenance Procedure Every 500 hours • Chang e the hy draulic lter (Ev er y 250 hours/yearly if using Mobil 1 15W50) • Check wheel hub-slotted tor que specication. Monthly • Check the battery c harge.
Maintenance 2. Lift dec k and secure in raised position as stated in the Clean Grass Build-Up Under Deck section. 3. Inspect blades and sharpen or replace as required. 4. R einstall the blades (if they were remov ed) in the following order: A. Install bushing through blade with bushing ange on bottom (grass) side of blade .
Maintenance Figure 12 1. Rod 4. Mower deck 2. Spring 5. Discharge deector bracket 3. Discharge deector 6. Assembled view 3. Hook the bent end of the rod around the front discharge deector brack et to retain it from sliding out.
Maintenance 1. Stop engine, w ait for all moving parts to stop , and remov e k ey or spark plug wire(s). Engage parking brake . 2. See the Engine Owner’ s Man ual for cleaning instr uctions . Change Engine Oil Service Interval: After the rst 5 hours Every 100 hours (May need more often under severe conditions.
Maintenance Lubrication Chart Fitting Locations Initial Pumps Number of Places Ser vice Inter v al 36 inch Deck 48 inch Deck 52 inch Deck 1. Caster Wheel Bearings 12 2 2 2 Daily 2. Caster Piv ots 2 2 2 2 Daily 3. PTO Engag ement Bellcrank 1 1 1 1 40 hours 4.
Maintenance 5. Loosen lter 1/2 turn and allow a small amount of oil to leak from the oil lter (this allo ws air to be purged from the oil lter and supply hose from the hy draulic reser v oir). T urn lter clockwise until rubber seal contacts the lter adapter .
Maintenance a steady ow of oil to o w out from under the housing . R etighten the capscrews . Do this for both pumps . Note: Hy draulic reser v oir can be pressurized up to 5 psi to speed this process . 6. If either dri ve wheel still does not rotate , stop and repeat steps 4 and 5 abo ve for the respectiv e pump .
Maintenance Mobil HTS Grease (Or Food-Grade Anti-seize) Mobil HTS grease (or food-grade anti-seize) is used in the following locations: • Between the cutter housing spindle and bearings . • Between the cutter housing spindle and sheav e. • Under top cutter housing bearing guard.
Maintenance Adjust the threaded yok e at the bottom of the speed control linkage (see Figure 15) until the tabs are positioned correctly . Figure 15 Viewed from Left Side of Unit 1. Neutral Safety Switch 3. 5/16 inch (.76 cm) 2. Actuating T ab in neutral position 3.
Maintenance disengag ed whenev er speed control lev ers are mov ed out of the neutral position. Note: The neutral lock latches should be “unlock ed” and in the forw ard position. 2. Loosen the front nut on left h ydro control linkage as sho wn in Figure 16.
Maintenance the mac hine, remov e jac k stands and carefully low er the mac hine to the g round. (Check the driv e tire pressure and tire circumference see Check the Tire Pressures section.) 2. R un the unit and obser v e the tracking on a level, smooth, hard surface such as concrete or asphalt.
Maintenance Cleaning Clean Engine and Exhaust System Area Service Interval: Before each use or daily (May be required more often in dry or dirty conditions.) CAUTION Excessi ve de bris around engine cooling air intake and exhaust system area can cause engine, exhaust area, and h y draulic system to o verheat which can create a re hazard.
Maintenance Battery Disposal DANGER Batter y electrol yte contains sulfuric acid, which is poisonous and can cause severe bur ns. Sw allowing electrolyte can be fatal or if it touches skin can cause sev ere bur ns. • W ear safety glasses to shield ey es, and r ub ber g lov es to protect skin and clothing when handling electrolyte.
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , do not o verlook the simple causes . F or example: starting problems could be caused by an empty fuel tank.
T roubleshooting Problem Possible Cause Cor rectiv e Action 1. T racking needs adjustment. 1. Adjust the tracking by turning knob on the right hydro control linkage in the direction that the mow er needs to be adjusted to . T urn the knob in 1/4 turn increments until the mow er trac ks correctly .
Schematics Schematics Electrical Diagram 15 & 17 HP KA W ASAKI SAFETY INTERLOCK MODULE TRANSMISSION SWITCH N.O . P ARK BRAKE SWITCH N.O . BLADE SWITCH N.O . OPC SWITCH N.O . KEY SWITCH ENGINE GROUND ENGINE KILL CONNECT ORS ARE VIEWED FROM WIRE END N.
Schematics Hydraulic Diagram 41.
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we .
Notes: 43.
Notes: 44.
Service Record Date: Description of Work Done: Service Done By: 45.
46.
47.
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Exmark 4500-358 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Exmark 4500-358 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Exmark 4500-358, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Exmark 4500-358 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Exmark 4500-358, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Exmark 4500-358.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Exmark 4500-358. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Exmark 4500-358 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
