Manuel d'utilisation / d'entretien du produit MMI-20020979 du fabricant Emerson Process Management
Aller à la page of 38
Installation Manual MMI-20020979, Rev AB May 2015 Micro Motion ® Gas Density Meters (GDM) Fiscal gas density measurement.
Safety and approval information This Micro Motion product complies with all applicable European directives when properly installed in accordance with the instructions in this manual. Refer to the EC declaration of conformity for directives that apply to this product.
Contents Chapter 1 Planning ...........................................................................................................................1 1.1 Installation checklist .......................................................................
Contents ii Micro Motion ® Gas Density Meters.
1 Planning Topics covered in this chapter: • Installation checklist • Best practices • Recommended sample flow rate • Power requirements • Installation requirements for the thermo-well pocket • Recommended installations for gas density applications • Perform a pre-installation meter check 1.
□ Make sure that the process gas meets the recommended characteristics regarding composition, temperature, and pressure for your installation. □ Verify that you have all equipment necessary for your installation. Depending on your application, you may be required to install additional parts for optimal performance of the meter.
1.3 Recommended sample flow rate Use the smallest acceptable flow rate for the process gas passing through the meter. This ensures a sample gas flow rate that is representative of the main flow with regard to the proportions of different gas constituents.
1.4 Power requirements Following are the DC power requirements to operate the meter: • 24 VDC, 0.45 W maximum • Minimum 22.8 VDC with 1000 m (3280 ft) of 0.20 mm 2 (18 AWG) power-supply cable • At startup, power source must provide a minimum of 0.
Minimum wire area (mm 2 per meter) Figure 1-3: 0.00 0 0.05 0 0.10 0 0.15 0 0.20 0 0.25 0 0.30 0 0.35 0 0.40 0 0.45 0 0.50 0 0.55 0 0.60 0 0.65 0 0.70 0 0.75 0 0.80 0 0.85 0 0.90 0 10 0 20 0 30 0 40 0 50 0 60 0 70 0 80 0 90 0 100 0 Mi nimum Wir e Ar e a (mm 2 ) Dis t a nc e of I nstall a t ion (m ) M i ni mu m W i re Ar ea ( m m 2 ) 22 .
Micro Motion thermo-well pocket dimensions Figure 1-4: 6.00 (152.30) Ø3.94 (100.00) 1.59 (40.30) 2.83 (72.00) Dimensions in inches (mm) 1.6 Recommended installations for gas density applications Micr.
Meter installation in a pressure recovery application The most common location for a density device in an orifice plate metering system is downstream from the orifice plate.
Meter installation in pressure recovery application Figure 1-5: STATUS SCROLL SELECT C A E A B D G F H J K I GDM A. Meter isolation valves B. Flowmeter C. Venting valve D. Flow control needle valve E. Filter F. Pipeline diameter G. Differential pressure transmitter H.
• Pressure drops through the valves and filters do not affect the reading. The pressure inside the meter and at the gas outlet is equal to the pressure at the orifice downstream point. • The correct expansion factor for the downstream point is used in the orifice flow calculations.
Meter installation in differential pressure application Figure 1-6: STATUS SCROLL SELECT E A A B D C F G H GDM A. Meter isolation valves B. Flowmeter C. Venting valve D. Flow control needle valve E. Filter F. Differential pressure transmitter G. Thermal insulation H.
Tip To avoid excessive pressure drops in your sample pipeline, be sure to monitor the condition of the filters. Do this by varying the sample flow rate and monitoring the magnitude of the resultant density changes. Pressure drops through the filters can cause density errors if they become too large.
Meter installation in a vented gas application Figure 1-7: STATUS SCROLL SELECT A B D F A E C G H GDM GDM I A. Meter isolation valves B. Flowmeter C. Venting valve D. Flow control needle valve E. Filter F. Pressure regulator G. Thermal insulation H. Vent/vacuum test point I.
Meter installation in an ultrasonic meter application Figure 1-8: STATUS SCROLL SELECT E C A B D A G H F GDM A. Meter isolation valves B. Flowmeter C. Venting valve D.
Meter installation with a turbine flow meter Figure 1-9: STATUS SCROLL SELECT A B D A E C H F G GDM A. Meter isolation valves B. Flowmeter C. Venting valve D.
CAUTION! Handle the meter with care. Follow all corporate, local, and national safety regulations for lifting and moving the meter. 2. Visually inspect the meter for any physical damage. If you notice any physical damage to the meter, immediately contact Micro Motion Customer Support at flow.
2 Mounting Topics covered in this chapter: • Mount the meter in the pipeline • Connect the gas bypass lines • Rotate the electronics on the meter (optional) • Rotate the display on the transmitter (optional) • Post-installation check 2.
Meter installation pieces Figure 2-1: STATUS SCROLL SELECT C D E B A A. M8 socket-head cap screw (for mounting) B. Meter housing C. Aluminum sleeve (cylinder) D. Anti-vibration gasket E. Thermo-well pocket Procedure 1. (Recommended) Install the thermo-well pocket in the aperture created in the pipeline and weld it into place.
Typical installation in pipeline (with thermo-well pocket) Figure 2-2: STATUS SCROLL SELECT Dimensions in inches (mm) 3.74 (95) 2.2 Connect the gas bypass lines Once you have mounted the meter in the pipeline, you are ready to connect the gas bypass lines.
Gas inlet/outlet connectors Figure 2-3: STATUS SCROLL SELECT C B A A. Process gas outlet B. Process gas inlet C. Filter Mounting Installation Manual 19.
2.3 Rotate the electronics on the meter (optional) You can rotate the transmitter on the meter up to 90°. 1. Using a 4 mm hex key, loosen the cap screw that holds the transmitter in place. Component to secure transmitter in place Figure 2-4: A A. M5 socket-head cap screw 2.
Display components Figure 2-5: B C D A D E A. Transmitter housing B. Sub-bezel C. Display module D. Display screws E. Display cover Procedure 1. If the meter is powered up, power it down. 2. Turn the display cover counterclockwise to remove it from the main enclosure.
2.5 Post-installation check After you complete the installation of the meter, pressure test the meter and associated pipework to 1 ½ times the maximum operating pressure.
3 Wiring Topics covered in this chapter: • Available output terminals and wiring requirements • Hazardous area output wiring 3.1 Available output terminals and wiring requirements Three pairs of wiring terminals are available for transmitter outputs.
Information provided about wiring the safety barriers and galvanic isolators is intended as an overview. You should wire the meter according to the standards that are applicable at your site. CAUTION! • Meter installation and wiring should be performed by suitably trained personnel only in accordance with the applicable code of practice.
RS-485 output and cable entity parameters (MTL7761AC) Table 3-3: Input parameters Voltage (U i ) 18 VDC Current (I i ) 100 mA Internal capacitance (C i ) 1 nF Internal inductance (L i ) 0.
3.2.2 Wire all available outputs using safety barriers Micro Motion provides a safety barrier installation kit for wiring the meter in a hazardous area. Contact your local sales representative or Micro Motion Customer Support at flow.support@emerson.com for more information on ordering a barrier kit.
Hazardous area mA/DO/TPS output wiring using safety barriers Figure 3-1: Bus Bar Hazardous Area Non-Hazardous Area MTL7761AC RS-485 A RS-485 B 3 4 1 2 24 VDC 24 VDC MTL7728P+ 24 VDC 3 4 1 2 MTL7728P+ .
CAUTION! • Meter installation and wiring should be performed by suitably trained personnel only in accordance with the applicable code of practice. • Refer to the hazardous area approvals documentation shipped with your meter.
Hazardous area output wiring using galvanic isolators (mA outputs option) Figure 3-2: mA1+ HART RS-485 PWR mA2 Hazardous Area Non-Hazardous Area MTL7761AC RS-485 A RS-485 B 3 4 1 2 MTL5541 2 1 14 13 12 11 MTL5523 2 1 24 VDC 14 13 12 11 24 VDC LINK 250 Ω MTL5541 2 1 14 13 12 11 24 VDC 250 Ω A B HART Device Signal Device 3.
Note The RS-485 barrier is not isolated. Output(s) Isolator 4–20 mA + HART MTL5541 • Time Period Signal (TPS) • Discrete MTL5532 Modbus/RS-485 MTL7761AC Power MTL5523 Procedure 1.
The switches are located on the side of the isolator, and must be set to either Off (the up position) or On (the down position). MTL5532 switch location (plus ON/OFF switch position) Figure 3-4: 1 2 3.
4 Grounding The meter must be grounded according to the standards that are applicable at the site. The customer is responsible for knowing and complying with all applicable standards.
Grounding Installation Manual 33.
*MMI-20020979* MMI-20020979 Rev AB 2015 Micro Motion Inc. USA Worldwide Headquarters 7070 Winchester Circle Boulder, Colorado 80301 T +1 303-527-5200 T +1 800-522-6277 F +1 303-530-8459 www.micromotion.com Micro Motion Europe Emerson Process Management Neonstraat 1 6718 WX Ede The Netherlands T +31 (0) 70 413 6666 F +31 (0) 318 495 556 www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Emerson Process Management MMI-20020979 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Emerson Process Management MMI-20020979 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Emerson Process Management MMI-20020979, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Emerson Process Management MMI-20020979 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Emerson Process Management MMI-20020979, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Emerson Process Management MMI-20020979.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Emerson Process Management MMI-20020979. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Emerson Process Management MMI-20020979 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
