Manuel d'utilisation / d'entretien du produit DH du fabricant Emerson
Aller à la page of 80
Precision Cooling For Business -Critic al C ontinuity™ Li eber t D el uxe S ys tem /3 ™ Operation and Maint enanc e Manual 50 and 60 Hz , 6-30 T on D X Syst ems (D H/DE /VH/VE); 12-60 T on CW Syst.
.
i T A BLE OF CONTENTS 1.0 I NTRODUCTI ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii 4.4 Main Menu (AG)—View/Set Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 0 4.4.1 Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii 5.0 R ESPONSE BY C ONTROL T YP E —A DVANCED M ICROPROCESSOR C ONTROLS . . . . . . . . . . . 33 5.1 Temperature Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 5.1.1 Cooling/H eating Requ ired, in Perce nt (%) .
iv 7.0 C OMPONENT O PERATION AND M AINTENANCE , C HECKS AND A DJUST MENT S . . . . . . . . . . . . 48 7.1 System Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 7.1.1 Environmental Control Functions .
v FIGURES Figure 1 Advanced microprocessor contro l panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 2 Advanced microprocessor (AM) control me nu . . . . . . . . . . . . . . . . . . . . . . .
vi.
Introd uction 1 1.0 I NTRODUCTION 1.1 System Description Liebert Deluxe environmental co ntrol systems are av ailable in several configurations. Each configu- ration can operate with either Advanced Microproc essor Controls (AM), or Advanced Microprocessor Controls with Gr aphics (AG).
Introd uction 2 1.1.3 Chilled W ater Systems These systems utilize a central chiller and control co oling by modu lating a control valve in the chilled water line.
Initial Start-Up Proced ure 3 2.0 I NITIAL S TAR T -U P P ROCEDURE Before beginning start-up, make ce rtain that unit was installed acco rding to the instructions in the Installation Manua l. All exterior panels must be in place. Locate the Start-Up form supplied with your unit documents.
Advanced Microprocessor Con trols Setup 4 3.0 A DVANCED M ICROPROCESSOR C ONTROLS S ETUP The Advanced Microprocessor (AM) Control for your Liebert Deluxe unit features an easy to use menu driven LCD display. The menus, control features , and circuit b oard details are described in this section.
Advanced Microprocessor Con trols Setup 5 Figure 2 Advanced micropr ocessor (AM) control menu Operating Status View Setpoints Temp Setpoints Sensitivity Hi Temp Alarm Lo Temp Alarm Hi Hum Ala rm Lo Hu.
Advanced Microprocessor Con trols Setup 6 3.3 Main Menu (AM)—St atus/Alarm Dat a Selecting STATUS/ALARM DATA from the Main Menu will display the following sel ections: ACTIVE ALARMS OPERATING STATUS ALARM HISTORY LOG RUN HOURS LOG ANALOG SENSORS 3.3.
Advanced Microprocessor Con trols Setup 7 3.3.5 Analog Sensors The four (4) analog sensor inputs can be monito red from this submenu of Status/Alarm Data. The inputs are filtered and displ ayed along with the text label assigned d uring setup. See Analog Setup on page 12 .
Advanced Microprocessor Con trols Setup 8 Setup Operation The Setup Operation permits the review and/or adju stment of the unit configuration. The menu may include: Cold Start: This feature, also refe.
Advanced Microprocessor Con trols Setup 9 Select Options The following tabl e lists ch oices on the Select Options menu. Thes e should match the options installed with your unit and should not need to change during normal operation. Calibrate Sensors The temperature an d humidity sensors can be cal ibr ated by selecting th is menu item.
Advanced Microprocessor Con trols Setup 10 Dehumidification with Normal or Delayed Reheat: Dehumidification with normal reheat allows for operating BOTH compressors and reheats simultan eously. It is very import ant that electrical ser- vice to the unit be sized and wi red for this optio n if selected.
Advanced Microprocessor Con trols Setup 11 Enable Alarms: Each indi vidual alar m can be selected to be ENABLED (annunciated audibl y, visu- ally, and communicated to a Site Prod ucts System) or DISABLED (ignored) . Enable Common Alarm: Each in dividual alarm ca n be selected to energize or to not energize the common alarm relay.
Advanced Microprocessor Con trols Setup 12 St andard Alarm Messages • Water under floor • Smoke detected • Standby GC pump on • Loss of water flow • Standby unit on For more information co ncerning alarms, see 6.0 - Alarm Description s and Solutions .
Advanced Microprocessor Con trols Setup 13 Set St atus Display The Status Display can be set to show the return air temper ature and humidity SENSOR READ- INGS or the temperature and humidity control SETPOINTS through this selection. When SET- POINTS is selected, the status di splay indicates so by displaying “SETPTS.
Advanced Microprocessor Con trols Setup 14 T est Output s When this feature is sel ected, the unit is e ffectively turned off. When stepping from one loa d to the next, the prev ious load, if on, i s turned off automatically. The load s can also be toggled on/off by selecting “ENTER”.
Advanced Microprocessor Con trols Setup 15 3.6 Main Menu (AM)—St atus Display The Status Display shows the presen t room temperature, humidity, active stat us functions (cooling, heating, dehumidify ing, humidifying), a nd active al arms. This is the data no rmally shown on the con- trol screen.
Advanced Microprocessor Con trols Setup 16 3.8.2 Nonvolatile Memory All critical in formation is stor ed in nonvolati le memory. Setpoi nts, setup paramet ers, and component run hours are kept inside the microcontroller in EEPROM. Information retained for the alarm history is kept in non- volatile RAM.
Advanced Microprocessor Con trols Setup 17 3.9.1 Monitor functions 1. Temperature /Humidity: Present readings 2. Statu s: Cooling/Heatin g and Humidifyin g/Dehumidifying operating status i n percent 3. Present Alarms: Alarms presently active 4. Alarm History: 10 most recent alarms (60 most recent alarms for AG ) 5.
Advanced Microprocesso r with Graphics Control Setup 18 4.0 A DVANCED M ICROPROCESSOR WITH G RAPHICS C ONTROL S ETUP The Advanced Microprocessor with Gr aphics (AG) Control for your Deluxe unit featu res an easy-to- use, menu-driven LCD Graphics Displ ay.
Advanced Microprocesso r with Graphics Control Setup 19 Figure 4 Advanced microprocessor with graphics (AG) control menu Normal Disp lay Date and Tim e Set Clock ** Optional Cursor M ovement Use UP /DOWN to move the cursor. Hit ENTER to select the menu it em.
Advanced Microprocesso r with Graphics Control Setup 20 4.2 Display the Main Menu—AG Control Press the MENU/ESC key to display the Main Menu. Th e Menu selections in clude: • VIEW/SET ALARMS • O.
Advanced Microprocesso r with Graphics Control Setup 21 4.4.3 Setup Alarms The list of alarms may be reviewed using the UP/DO WN keys. Any alarm may be selected to have its parameters modified by pressing the ENTER key. All alar ms have a time delay and alarm type parameter.
Advanced Microprocesso r with Graphics Control Setup 22 4.4.4 Set Up Custom Alarms Selecting SETUP CUSTO M ALARMS will step to the following m enu: • SETUP CUSTOM ALARM TEXT • CHANGE CUSTOM TEXT 1.
Advanced Microprocesso r with Graphics Control Setup 23 4.5 Main Menu (AG)—Operating St atus The Operating Sta tus is intended to provid e the user with displayed i nformation concern ing what the control is calling for the system to do. For example: The display indi cates the chilled water valve is 68% open .
Advanced Microprocesso r with Graphics Control Setup 24 4.7.1 Setup Operation The SETUP OPERATION menu permits the review and/or adjustment of the unit configuration.
Advanced Microprocesso r with Graphics Control Setup 25 4.7.2 Select Options The following table is a list of feat ures that should match the option s installed with your unit and should not need to change during normal operation. 4.7.3 Calibrate Sensors The temperature and humidity sensors can be cali brated by selecting this menu item.
Advanced Microprocesso r with Graphics Control Setup 26 4.7.6 Select Humidity Sensing Mode This screen permits the user to select between RELATIVE (direct) and ABSOLUTE (predictive) humidity control. If relati ve is selected, the RH control is taken directly from the RH sensor.
Advanced Microprocesso r with Graphics Control Setup 27 4.8.1 Show Input s With the unit on and the fan running, the input state for the fo llowing devices may be displa yed: • Air Sail Switch: norm.
Advanced Microprocesso r with Graphics Control Setup 28 4.8.4 DIP Switches The DIP switch settings can be reviewed from the display panel. Chang ing the DIP switches requires opening the front pa nel for access to the DIP switches on the microprocessor control board.
Advanced Microprocesso r with Graphics Control Setup 29 Six different data types are recorded f or graphing: temperature, humidity, and fou r user defined ana- log inputs. Each data type can be viewed over thr ee different time scales and two different resolu- tions.
Advanced Microprocesso r with Graphics Control Setup 30 4.1 1.3 Read Digit al Inputs The four custom alarm inputs can be defined to be digital inputs. Digital inpu ts are used to sense cus- tomer devices for status display purposes only and will not activate the audibl e alarm.
Advanced Microprocesso r with Graphics Control Setup 31 4.13.3 Compressor Sequencing Control The lead compressor is the first one to be turned on when compressor operat ion is required. The la g compressor is turned on second if both compressors are required.
Advanced Microprocesso r with Graphics Control Setup 32 4.14.4 Control Output s Active control outputs are indicated with LEDs on the lower sec tion of the control board. Each LED is lit if the control output is active (on). Use thes e LEDs to assist in troubleshooting the system.
Response by Control T ype—Advance d Microprocessor Controls 33 5.0 R ESPONSE BY C ON TROL T YPE —A DVANCED M ICROPROCESSOR C ONTROLS This section describes how your Advanced Microprocessor Controls respond depending on the algo- rithm/control type selected in setting up the controls.
Response by Control T ype—Advance d Microprocessor Controls 34 5.1.3 Cooling Operation T wo-Step Cooling, Compressorized Direct Exp ansion (DX) Systems The first stage of cooling activate s when the temperature control calc ulates a requirement fo r cooling of 50%.
Response by Control T ype—Advance d Microprocessor Controls 35 Hot W ater/Steam Heat The valve begins to open when the requirement fo r heating is 33% and is proportionally adjusted until the valve is full open at 1 00% heat req uirement. 5.2 Humidity Control 5.
Response by Control T ype—Advance d Microprocessor Controls 36 Dual Cooling Source Dehumidification When dual cooling is availa ble, the humidity cont rol will calcula te a total dehumidificati on require- ment of 200% rather than 100%. The cooling v alve opens proport ionally as the requirement for dehu- midification rises fr om 0 to 100%.
Response by Control T ype—Advance d Microprocessor Controls 37 Suggested System T uning Procedure 1. Initially adjust the integral and deriva tive settings to 0%/degree- min and 0%/d egree/min.
Response by Control T ype—Advance d Microprocessor Controls 38 Intelligent Control The Intelligent Control oper ates from a set of gene ra l rules that define how the control output should be adjusted for different system condi tions.
Response by Control T ype—Advance d Microprocessor Controls 39 5.3 Load Control Features 5.3.1 Short Cycle Control The control system monitors both compressors and prevents each fr om turning on w ithin a 3 minute period of being turned off.
Response by Control T ype—Advance d Microprocessor Controls 40 5.4 Analog Sensors 5.4.1 Connecting the Analog Senso rs The sensor inputs are factory-set to accept a 4 - 20 mA signal. The inputs can be changed by removing the appropriate jumpers on th e control circuit board.
Response by Control T ype—Advance d Microprocessor Controls 41 5.4.2 W ater Detection Display The water detection display is designed to graphica lly display the location of water under a raised floor when connected to an LT750 water detection system.
Response by Control T ype—Advance d Microprocessor Controls 42 Calibration Calibration should not be requi red for most installations. The accuracy of this disp lay is approxi- mately 1%. The display is calibrat ed by the slope and intercept v alues of Analog Inp ut #1.
Response by Control T ype—Advance d Microprocessor Controls 43 5.5.2 Vie w/Change Functions: 1. Setpoints Temperature Setpoint Temperature Sensitivity Humidity Setpoint Humidity Sensitivity High Temperature Alarm Low Temperature Alarm High Humidity Alarm Low Humidity Alarm Cold Start Delay Humidifier Flush Rate Chilled Wa ter Flush Rate 2.
Alarm Descriptions and Solutions 44 6.0 A LARM D ESCRIPTIONS AN D S OLUTIONS The Advanced Microprocessor (AM) and the Advanc ed Microprocessor with Graphics (AG) Control systems will aud ibly and visually ann unciate all Enabled alarms, inclu d ing the four (4) custom alarms.
Alarm Descriptions and Solutions 45 6.1.3 Custom Alarms (Only With Advanced Controls) Custom alarm messages are progra mmed at the LCD display. The al arms may be specified by the customer at the time of order. Additional d evices and wiring may be required at the factory or by oth- ers.
Alarm Descriptions and Solutions 46 6.1.10 Loss of Air Flow A differential air pressure swi tch is used to indica te loss of air flow in Deluxe units. Check for blockage of unit air outlet or inlet. C h eck blower motor fuses and over load reset. Check for broken belts.
Alarm Descriptions and Solutions 47 6.2 Optional/Custom Alarms 6.2.1 Loss of W ater Flow No water flow is detected in the chilled water or condenser water supp ly line. An optional flow switch is required for this alarm. Check for serv ice valves closed, pumps not w orking, etc.
Component Operat ion and Maintenance, Checks and Adjustmen ts 48 7.0 C OMPONENT O PERATION AND M AINTENANCE , C HECKS AND A DJUSTMENT S 7.1 System T esting 7.1.1 Environment al Control Functions The performance of all control circuit s can be tested by actuating each of the main functions.
Component Operat ion and Maintenance, Checks and Adjustmen ts 49 7.1.2 Electric Panel The electric panel should be inspecte d for any lo ose electrical connections. Control T ransformer and Fuses The control system is divided into four (4) sepa ra te circuits.
Component Operat ion and Maintenance, Checks and Adjustmen ts 50 7.2 Filters Filters are usually the most neglected item in an environmental control system .
Component Operat ion and Maintenance, Checks and Adjustmen ts 51 7.3.3 Electronic V ariable Speed Drive (Inverter) On large De luxe chilled wate r models an option al variable spee d drive inverte r is available. Th is packaged unit is factory set and should n ot requir e field adjustments.
Component Operat ion and Maintenance, Checks and Adjustmen ts 52 7.4.2 Suction Pressure Suction pressure will vary with load conditions. Th e low pressure sw itch will shut the compressor down if suction pressure falls be low the cut-out setting.
Component Operat ion and Maintenance, Checks and Adjustmen ts 53 Adjustment To adjust the superheat setting, proceed as follows: 1. Remove the valve cap at the bottom of the valve. 2. Turn the adjusting st em counterclockwise to lower the superheat. 3.
Component Operat ion and Maintenance, Checks and Adjustmen ts 54 7.4.7 Air Cooled Condenser Restricted airflow through the conden ser coil will reduce the operatin g efficiency of the unit and can result in high compressor head pressure and loss of cooling.
Component Operat ion and Maintenance, Checks and Adjustmen ts 55 7.4.8 W ater/Glycol Cooled Condensers Shell and T ube Condensers Each water or glycol cooled modu le has a shell and tube condenser which consists of a shell, remov- able heads, g askets and cleanable co pper tubes.
Component Operat ion and Maintenance, Checks and Adjustmen ts 56 7.4.9 Compressor Replacement Infrequently, a fault in the motor insulation may result in a motor burn.
Component Operat ion and Maintenance, Checks and Adjustmen ts 57 Compressor Replacement Procedure Replacement compressors are availa ble from your Lieb ert supplier. They will be shi pped in a reusable crate to the job site as required by the service contractor.
Component Operat ion and Maintenance, Checks and Adjustmen ts 58 Changing Humidifier Lamp s 1. Open disconne ct switch. 2. Open middle front panel. 3. Remove screws securing li ne voltage compartment cove r, then remove the cover.
Component Operat ion and Maintenance, Checks and Adjustmen ts 59 7.5.2 Stea m Generating Humidifier The humidifie r drains and refills to maintain a current setpoi nt and alert the operator when the humidifier canister needs to be repl aced.
Component Operat ion and Maintenance, Checks and Adjustmen ts 60 Controls The humidifier RUN/DRAIN switch is located in th e unit low voltage compartment for most Deluxe models (in the hu midifier assembly for model s FH599, 600, 739, 740C).
Component Operat ion and Maintenance, Checks and Adjustmen ts 61 11. The canister is now re ady to be removed. On the downflow chilled water units: Slide the hum idifier cabinet bo ttom straight out toward you and drop the canister throug h the botto m of the cabinet.
Component Operat ion and Maintenance, Checks and Adjustmen ts 62 Circuit Board Adjustment s Humidifier operation is governed by the humidi fier control board. Th is board is locat ed in the lower right area of the panel in the cont ro l section of the unit, or in th e humidifier compartment on models FH599C, 600C, 739C and 740C.
Component Operat ion and Maintenance, Checks and Adjustmen ts 63 Figure 12 Steam gen erating humidifier control board 7.6 Electric Reheat T able 20 DIP switch settings for steam generatin g humidifier Unit Rated Voltage Capacity SW1 SW2 SW3 SW4 Rated Values Voltage AMP Set Pt 200/208 11 Off On Off On 208 12.
Trou bleshoot ing 64 8.0 T ROUBLES HOOTING Use this section in troubleshooting your u nit. Also refer to 6.0 - Alarm Descriptions and Solu- tions . Suggestions are grouped by prod uct function for convenience. ! WARNING Only qualif ied personnel should perform serv ice on these units.
Trou bleshoot ing 65 T able 23 Compressor and refrigeration system trou bleshooting Symptom Possible Cause Check or Remedy Compressor will not start Power off Check main switch , fuses or CBs and wiri.
Trou bleshoot ing 66 Refriger ant flooding Defective or improperly set expansion valve Increase superheat or replace valve Evaporator fan motor or belt Correct probl em or replace fan motor and/or belts. Low condensing pressure Check head pressure control device Slipping belts Inspect and adjust Blown valve plate or cylinder head in comp.
Trou bleshoot ing 67 Compressor continually cycles Faulty low pressure switch Repair or replace. Dirt or restriction in tubing to pressure stat Check and clean tubing. Defective liquid line solenoid valve Check valve and solenoid operator; re place if necessary.
Trou bleshoot ing 68 T able 26 Humidifier—steam generator troubleshooting Symptom P ossible Cause Check or Remedy False canister full indication Foaming Check drain valve to ensure that it drains freely. Check and replace if defective. Check water supply.
Trou bleshoot ing 69 Excessive arcing in the canister Drain valve clogged or defective Verify that drain valve operates freely when activated. Clean valve and replace coil or valve if defective.
Maintenance Inspecti on Checklist—Monthly 70 9.0 M AINTENANCE I NSPECTION C HECKLIST —M ONTHLY Date: Prepared by: Model #: Serial #: Filters Refrigeration Cycle/Section 1. Unres tricted air flow 1. Check suction pressure 2. Check filter switch 2. Check refrigerant lines 3.
Maintenance Inspection Chec klist—Semiannual 71 10.0 M AINTENANCE I NSPECTION C HECKLIST —S EMIANNUAL Date: Prepared by: Model #: Serial #: Filters Refrigeration Cycle/Section 1. Unrestricted air flow 1. Check suction pressure 2. C heck filter switch 2.
Ensuring The Hi gh A vai labilit y 0f Mission-Critic al Data And Ap plic ations. Emerson Net work P ower , the global leader in enabling business-critical continuity , ensures network resiliency and a.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Emerson DH c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Emerson DH - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Emerson DH, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Emerson DH va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Emerson DH, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Emerson DH.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Emerson DH. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Emerson DH ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
