Manuel d'utilisation / d'entretien du produit IC-F15/S du fabricant Elta
Aller à la page of 40
INSTRUCTION MANUAL UHF TRANSCEIVER iF25/S VHF TRANSCEIVER iF15/S IC-F15_F25-2.qxd 06.8.23 11:24 AM Page A (1,1).
i FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver . SA VE THIS INSTRUCTION MANUAL— This instruction manual contains important operating instructions for the IC-F15/ F15S VHF TRANSCEIVER and IC-F25/F25S UHF TRANSCEIVER .
ii PRECAUTION R W ARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body , especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical.
iii T ABLE OF CONTENTS FOREWORD ……………………………………………………………… i EXPLICIT DEFINITIONS ………………………………………………… i OPERA TING N.
1 1 ACCESSORIES 1 ■ Supplied accessories The following accessories are supplied: Qty . q Flexible antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 w Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 1 ACCESSORIES ■ Accessory attachments D Flexible antenna Connect the supplied flexible an- tenna to the antenna connector . CAUTION: • NEVER HOLD by the antenna when carrying the transceiver . • T ransmitting without an antenna may damage the transceiver .
3 1 ACCESSORIES 1 ï Battery pack T o attach the battery pack: Slide the battery pack on the back of the transceiver in the direc- tion of the arrow ( q ), then lock it with the battery release button. • Slide the battery pack until the battery release button makes a ‘click’ sound.
4 1 ACCESSORIES ï Jack cover Attach the jack cover when the optional speaker-microphone is not used. w w q q q w T o attach the jack cover: q Attach the jack cover to the [SP MIC] connector . w T ighten the screws. T o detach the jack cover: q Unscrew the screws with a phillips screwdriver .
5 1 ACCESSORIES 1 D Belt clip T o attach the belt clip: q Release the battery pack if it is attached. w Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a ‘click’ sound. T o detach the belt clip: q Release the battery pack if it is attached.
6 2 P ANEL DESCRIPTION ■ Front, top and side panels q CHANNEL SW/SELECTOR • IC-F15S/F25S: T oggle the channel switch to select the pre-pro- grammed channel 1 or 2. • IC-F15/F25 : Rotate the channel selector to select the pre- programmed memory channels.
7 2 P ANEL DESCRIPTION 2 e LED INDICA TOR (p. 8) ➥ Lights red while transmitting. ➥ Lights green while receiving a signal, or when the squelch is open. ➥ Lights/blinks orange when the matched 2/5-tone code is re- ceived, according to the pre-programming.
8 2 P ANEL DESCRIPTION ‘ ‘ LED indicator The LED indicator indicates several informa- tion as follows; (Ref.; R=Red, G=Green, O=Orange) R R R R O O O O G G G G G G R O R O R O R O R O R O R O R O G G G R • TX: T urns Red while transmitting a signal.
9 2 P ANEL DESCRIPTION 2 ‘ ‘ Programmable function keys The following functions can be assigned to [Upper] and [Lower] programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming.
10 2 P ANEL DESCRIPTION MONITOR KEY ➥ Mute and release the CTCSS (DTCS) or 2-tone squelch mute. Open any squelch/deactivate any mute while pushing this key .
11 2 P ANEL DESCRIPTION 2 DTMF AUTODIAL KEY Push to transmit the programmed DTMF code. CALL KEYS Push to transmit a 2/5-tone code. • Call transmission is necessary before you call another station de- pending on your signalling system.
12 3 CONVENTIONAL OPERA TION ■ T urning power ON ➥ Rotate [VOL] to turn power ON. ■ Channel selection IC-F15S/F25S : T oggle [CHANNEL SWITCH] to select the channel 1 or 2, or , push one of [MR- CH 1] to [MR-CH 4] key to select a chan- nel directly .
13 3 CONVENTIONAL OPERA TION 3 ■ Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice trans- mission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you.
14 3 CONVENTIONAL OPERA TION ■ Receiving and transmitting NOTE: T ransmitting without an antenna may damage the trans- ceiver . See p. 2 for antenna attachment.
15 3 CONVENTIONAL OPERA TION 3 D T ransmitting notes • T ransmit inhibit function The transceiver has several inhibit functions which restrict trans- mission under the following conditions: - The channel is in mute condition. - Channel is busy . - Un-matched (or matched) CTCSS is received.
16 3 CONVENTIONAL OPERA TION ■ Scrambler function The optional voice scrambler units UT -109 (#01) and UT -1 10 (#01) provide high performance private communication between stations with the same scrambler codes. ➥ Push and hold [Scrambler] to turn the scrambler function ON.
17 3 CONVENTIONAL OPERA TION 3 ■ Man Down Emergency Call The man down emergency call function transmits an emergency call automatically , after the transceiver laying down in a horizontal position for a pre-set time period. (The optional UT -1 13 MAN DOWN UNIT is required.
18 4 OPTIONAL UNIT INST ALLA TION ■ Optional unit installation Install the optional unit as follows: q Rotate [VOL] to turn the power OFF , and remove the battery pack.
19 4 OPTIONAL UNIT INST ALLA TION 4 ■ Scrambler unit installation The following PC board modification is required when installing the optional UT -109 or UT -1 10. q Rotate [VOL] to turn the power OFF , and remove the battery pack. (p. 3) w Remove the unit cover as shown at left (Optional unit installation.
20 5 BA TTER Y CHARGING ■ Battery charging Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation.
21 5 BA TTERY CHARGING 5 ■ Caution R DANGER Charge the specified Icom batteries only . Only tested and approved for use with genuine Icom batteries.
22 5 BA TTERY CHARGING ■ Optional battery chargers D Rapid charging with the BC-160 The optional BC-160 provides rapid charging of optional Li-Ion bat - tery packs. • An AC adapter (may be supplied with BC-160 depending on ver- sion) or the DC power cable (OPC-515L/CP-17L) is additionally required.
23 5 BA TTERY CHARGING 5 ï AD-106 installation q Install the AD-106 desktop charger adapter into the holder space of the BC-1 19N/121N. w Connect the plugs of the BC-1 19N/BC-121N to the AD-106 with the connector , then install the adapter into the charger with the supplied screws.
24 5 BA TTERY CHARGING D Rapid charging with the BC-1 19N+AD-106 The optional BC-1 19N provides rapid charging of optional Li-Ion battery packs. The following items are additionally required: • One AD-106 (purchase separately) . • An AC adapter (may be supplied with BC-1 19N depending on ver- sion) or the DC power cable (OPC-515L/CP-17L).
25 5 BA TTERY CHARGING 5 D Rapid charging with the BC-121N+AD-106 The optional BC-121N allows up to 6 battery packs to be charged simultaneously . The following items are additionally required.
26 6 SWIVEL BEL T CLIP ■ MB-93 contents Qty . q Belt clip …………………………………………………………… 1 w Base clip …………………………………………………………… 1 ■ T o attach q Release the battery pack if it is attached.
27 6 SWIVEL BEL T CLIP 6 e Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted fully into the groove. r Once the transceiver is locked in place, it swivels as illustrated below . IC-F15_F25-2.
28 6 SWIVEL BEL T CLIP ■ T o detach q T urn the transceiver upside down in the direction of the arrow and pull out from the belt clip. IC-F15_F25-2.qxd 06.
29 6 SWIVEL BEL T CLIP 6 w Release the battery pack if it is attached. (p. 3) e Pinch the clip ( q ), and slide the base clip in the direction of the arrow ( w ). CAUTION: HOLD THE TRANSCEIVER TIGHTL Y , WHEN HANGING OR DET ACHING THE TRANSCEIVER FROM THE BEL T CLIP .
30 7 OPTIONS D BA TTER Y P ACK • BP-230 Li-Ion BA TTERY P ACK 7.4 V/800 mAh Li-Ion battery pack, allows approx. 5.5 hours* op- eration. • BP-231 Li-Ion BA TTERY P ACK 7.4 V/1 150 mAh Li-Ion battery pack, allows approx. 8 hours* op- eration. • BP-232 Li-Ion BA TTERY P ACK 7.
31 7 OPTIONS 7 D BEL T CLIPS • MB-93 SWIVEL BEL T CLIP • MB-94 BEL T CLIP Exclusive alligator-type belt clip. The same as supplied with the transceiver . • MB-96N/96F LEA THER BEL T HANGER D DC CABLES • CP-17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket.
32 8 DOC CE versions of the IC-F15/S and IC-F25/S which display the “CE” symbol on the serial number seal, comply with the essential requirements of the Euro - pean Radio and T elecommunication T erminal Direc- tive 1999/5/EC. DECLARATION OF CONFORMITY We Icom Inc.
33 8 DOC 8 This warning symbol indicates that this equipment op- erates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use. Be sure to check that you have the correct version of this radio or the correct programming of this radio, to comply with national licensing requirement.
MEMO IC-F15_F25-2.qxd 06.8.23 11:24 AM Page 34 (1,1).
MEMO IC-F15_F25-2.qxd 06.8.23 11:24 AM Page 35 (1,1).
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6370D-1EU- w Printed in Japan © 2004–2006 Icom Inc. < Intended Country of Use > GER AUT GBR IRL NOR FRA NED BEL LUX ESP POR ITA GRE SWE DEN FIN SUI IC-F15_F25-2.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Elta IC-F15/S c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Elta IC-F15/S - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Elta IC-F15/S, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Elta IC-F15/S va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Elta IC-F15/S, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Elta IC-F15/S.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Elta IC-F15/S. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Elta IC-F15/S ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
