Manuel d'utilisation / d'entretien du produit AOFP201RU du fabricant Electrolux
Aller à la page of 27
PART NO. 595R 05100 VERSION 1 2007.06 INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS ISTRUZIONI DI INSTALLAZIONE, FUNZIONAMENTO E MANUTENZIONE INSTRUCTIONS D'INSTALLATION, D'UTILISATIO.
2 Fig.1 8 11 20 23 34 15 16 12 25 24 1 31 2 4 3 5 6 7 9 10 17 18 19 13 14 22 21 26 27 28 30 29 CONTROL PANEL PANNELLO COMANDI PANNEAU DE COMMANDE PANEL DE CONTROL 33 32 34.
3 USA 1 - ON/OFF switch 2 - “START / STOP" (cycle start / stop) button 3 - “CRUISE CHILLING” button- automatic cycle (cycle start / stop) 4 - “SOFT chilling cycle” indicator light 5 - .
4 FR 1 - Interrupteur ON/OFF 2 - Touche START / STOP (marche / arrêt du cycle) 3 - Touche “cruise chilling” - cycle automatique (marche / arrêt du cycle) 4 - Le d "SOFT Chilling" (cycl.
5 USA ............................................. Page 06 - 27 IT ................................................. Pagina 28 - 50 FR ...............
6 SAFETY INSTRUCTIONS ......................................................... Page 9 A . 1 GENERAL INFORMA TION ........................................................ Page 10 A.1.1 Foreword .........................................................
7 C.1.9.1 Manual defrosting ...................................................................................................... . Page 1 3 C.1.9.2 Probe temperatures display ..........................................................................
8 C.4 ALARMS .................................................................................... Page 20 C.4.1 Alarms ......................................................................................................................... Page 20 C.
9 SAFETY INSTRUCTIONS T o reduce the risk of fire, electrical shock, or injury when using your appliance, please follow these basic precautions including the following: • Read all instructions before using your appliance. • This Manual does not cover every possible condition and situation that may occur .
10 Adjust the height and level the appliance by means of the leveling feet, checking that the door opens and closes properly. +50 mm + 1.97 " -10 mm - 0.39 " A.1.6 DATA PLATE POSITION The data plate with all the appliance specifications is located on the chilling unit compartment, on the lower left-hand side.
11 B.1.3 MAINTENANCE CYCLE OR PRESERVATION CYCLE The maintenance cycle is the maintenance of the food at a chosen temperature so that it does not alter over time, is started automatically at the end of the blast chilling or freezing cycle. The preservation cycle is continuous.
12 C.1.4 PROGRAMS Press the button to set the appliance for programs mode. The appliance switches from standard cycle selection mode to program mode and vice versa. From left to right: - Turbo cooling - Program P1 - Program P2 Associated with each standard cycle are 2 default programs that can be varied by the user.
13 C.1.8 TIME • During a chilling cycle: the time display shows the total or remaining chilling time. • During holding cycle: the display shows the hour. • During “turbo cooling” cycle: the display shows: “ °°°° “ = two hours left until start of defrosting " °°° " = 1.
14 C.1.9.4 REFERENCE STANDARD The machine can be set to 3 different Standards: 1. Electrolux Food Safe Mode 1 2. Electrolux Food Safe Mode 2 3. U.S. Standard The default setting for the appliance is the NSF rule number seven, which states that the product is chilled from 140°F/60°C to 39.
15 Before using the appliance, clean the chamber with a detergent solution, as there may still be condensation in the chamber left over from the final testing by the manufacturers (see section D.
16 program indicator light switches on. • to start the program, press the button. The user can edit some of the cycle parameters and save the changes: - for blast chilling, the user can edit the chamber chilling time/ setpoint and save it in the memory, from where it can subsequently be retrieved (see section C.
17 C.2.4 DEFROSTING If the appliance is in the right conditions (indicator light or or with the appliance on standby), this function enables a manual defrosting cycle.
18 C.2.7 INSERTING THE FOOD (CORE) PROBE IN THE PRODUCT Make sure the probe is clean and sterilized whenever inserting it in food, and always take care when handling the probe, because it has a sharp point. Using the food (core) probe in the chilling cycles guarantees good results.
19 IF YOU WANT TO CHANGE THE TYPE OF PROGRAM PRESS THE BUTTON UNTIL THE INDICATOR LIGHT TURNS ORANGE PRESS THE CYCLE BUTTON - Hard chilling with program select and chilling time change : PRESS THE BUT.
20 C.4.1 ALARMS The electronic board manages two kinds of alarm system: - HACCP for monitoring and storing high temperature alarms. HACCP alarm states are signalled by the sounding of the buzzer, the blinking of the red HACCP indicator light and the appearance of an alarm message on the display .
21 C.4.1.2.2 Service alarms requiring service center assistance When the alarms listed below occur, call the service center for assistance. All alarms will be stored as follows: the “TEMPERATURE” display shows the alarm number, e.g. “AL 1”, “AL 2”, etc.
22 ATTENTION: the AOFP201RU4-201RU-202RU-202RU4 model does not have a drain tray. Make sure the drain hole is connected to the water drain system. D.1.3 CLEANING THE FOOD (CORE) PROBE Pay particular attention when handling the probe; remember that it has a sharp point, therefore handle it with extreme care, even in the cleaning phase.
23 D.2.3 FAN REPLACEMENT (ONLY ON MODELS AOFP61U-61TU-61U4-61TU4) FIG. 2 FIG. 3 1 2 4 5 3 6.
24 D.3.1 QUICK TROUBLESHOOTING GUIDE In some cases faults can be remedied easily and quickly. Below there is a list of possible faults and remedies: A.
25 N.B. The default parameters (DEF.) may vary for different appliance models. D.6 LIST OF USER PARAMETERS SY MB O L RANG E DE F . MI N In te r n al c l o ck: M i n u te s 0 ..5 9 0 HOUR In t ern a l cl o ck: Ho ur s 0 ..2 3 0 DAY Inter na l cl o ck: Da y s 1 .
26 RECIPE SELECTION No t s ui tabl e in one pi ec e . Cut into 4.4 - 6.6 lb (2 - 3 kg) siz e, hard with probe O x t ongue w ith probe V eal shoul der roas t 1 join t per rac k 11 lb ( 5 k g) per 2.56 i n ( 65 m m ) GN pan c heck after 20' Mea t t errine w ith probe 0.
27 Gn o c c h i a lla r o m an a I f regenerated , with pro be 1.57 i n (40 m m ) pans in 1.57 i n (40 m m ) GN pan w ith pro b e Ri ce - pi la f sty l e w i th probe (stir ri c e e very 5 - 8') w ith pro b e Veget a bl e l as a gne w ith pro b e Baked pasta w ith pro b e 2.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Electrolux AOFP201RU c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Electrolux AOFP201RU - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Electrolux AOFP201RU, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Electrolux AOFP201RU va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Electrolux AOFP201RU, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Electrolux AOFP201RU.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Electrolux AOFP201RU. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Electrolux AOFP201RU ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
