Manuel d'utilisation / d'entretien du produit LC-XM1 du fabricant Eiki
Aller à la page of 40
MODEL LC-XM1 MUL TIMEDIA PR OJECT OR O WNER’S MANU AL.
2 Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.
3 SAFETY INSTR UCTIONS All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners.
4 COMPLIANCES Federal Comm unication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
5 T ABLE OF CONTENTS FEA TURES AND DESIGN 6 BEFORE OPERA TION 14 COMPUTER MODE 22 VIDEO MODE 29 SETTING 32 APPENDIX 34 PREP ARA TION 7 NAME OF EACH PART OF THE PROJECTOR 7 SETTING-UP THE PROJECTOR 8 C.
6 FEA TURES AND DESIGN This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.
7 PREP ARA TION NAME OF EA CH P AR T OF THE PROJECT OR B A CK OF THE CABINET HOT AIR EXHAUSTED ! Air blown from the exhaust vent is hot. When using or installing the projector, the following precautions should be taken. ● Do not put a flammable object near this vent.
SETTING-UP THE PR OJECT OR 8 PREP ARA TION This projector uses nominal input voltages of 100-120 V or 200-240 V AC. The projector automatically selects the correct input voltage. It is designed to work with single- phase power systems having a grounded neutral conductor.
9 PREP ARA TION POSITIONING THE PR OJECT OR ● This projector is designed to project on a flat projection surface. ● The projector can be focused from 5.2 ’ (1.6m) ~ 26.3 ’ (8.0m). ● Refer to the figure below to adjust the screen size. ADJUST ABLE FEET Picture tilt and projection angle can be adjusted by rotating the ADJUSTABLE FEET.
10 PREP ARA TION When moving the projector, replace the lens cover and retract the feet to prevent damage to the lens and cabinet. When this projector is not in use for an extended period, put it into the case (carrying bag) supplied with this projector.
11 COMPUTER IN S – VIDEO COMPUTER CONTROL POR T RESET A UDIO IN AV Y – Pb/Cb – Pr/Cr A UDIO OUT VIDEO CONNECTING THE PR OJECT OR TERMINALS OF THE PR OJECT OR Connect the computer output to this terminal.
12 CONNECTING THE PR OJECT OR CONNECTING T O THE VIDEO EQ UIPMENT COMPUTER IN S – VIDEO COMPUTER CONTROL PORT RESET A UDIO IN AV Y – Pb/Cb – Pr/Cr A UDIO OUT VIDEO Video Source (example) Video C.
13 CONNECTING THE PR OJECT OR COMPUTER IN S – VIDEO COMPUTER CONTROL PORT RESET AUD IO IN AV Y – Pb/Cb – Pr/Cr AUDIO OUT VIDEO 13" MODE (640 x 480) 16" MODE (832 x 624) 19" MODE (.
14 V OLUME ON-OFF D.ZOOM KEYST ONE VIDEO MENU MUTE P-TIMER NO SHO W FREEZE A UT O IMA GE NORMAL COMPUTER LOCK BEFORE OPERA TION OPERA TION OF THE REMO TE CONTR OL Used to select COMPUTER input source. (P22) Used to select VIDEO source. (P29) Used to execute the item selected or to expand the image in DIGITAL ZOOM mode.
15 BEFORE OPERA TION V OLUME ON-OFF D.ZOOM KEYST ONE VIDEO MENU MUTE P-TIMER NO SHO W FREEZE A UT O IMA GE NORMAL COMPUTER LOCK MUTE BUTTON Used to mute sound.(P21) NO SHOW BUTTON Used to turn the picture into black image. (P21) AUTO IMAGE BUTTON Use to operate AUTO IMAGE function.
16 BEFORE OPERA TION T OP CONTR OLS AND INDICA T ORS ON – OFF MENU MODE NORMAL LAMP REPLA CE W ARNING TEMP . READ Y LAMP WIDE TELE Used to open or close the MENU operation. (P17, 18) MENU BUTTON MODE BUTTON READY INDICATOR SELECT BUTTON POWER ON – OFF BUTTON NORMAL BUTTON WARNING TEMP.
17 BEFORE OPERA TION HO W T O OPERA TE ON-SCREEN MENU FLO W OF ON-SCREEN MENU Display ON-SCREEN MENU Press MENU button to display the ON-SCREEN MENU (MENU BAR). The red frame is the POINTER. Select the ITEM by pressing SELECT button. The dialog box of the ITEM appears.
18 BEFORE OPERA TION MENU B AR SYSTEM MENU Used to select a computer system. (Refer to P22) IMAGE MENU Used to adjust the computer image. [Fine sync / Total dots / White Balance / Contrast / Brightness / Gamma] (Refer to P26) PC ADJUST MENU Used to adjust the parameters to match with the input signal format.
19 B ASIC OPERA TION TURNING ON THE PR OJECT OR Connect the projector's AC Power Cord into a wall outlet. The LAMP indicator lights RED, and the READY indicator lights GREEN. Press the power ON-OFF button on the Remote Control Unit or on the Top Control to ON.
20 B ASIC OPERA TION ADJUSTING THE IMA GE KEYST ONE ADJUSTMENT 1 Press the KEYSTONE ▲ / ▼ button on the Remote Control Unit or select the Keystone on the SCREEN menu. (Refer to page 28, 30.) The message “ Keystone ” is displayed. 2 Correct the Keystone distortion by pressing the KEYSTONE ▲ / ▼ button or the POINT UP/DOWN button(s).
21 B ASIC OPERA TION Press the VOLUME (+/ – ) button on the Remote Control Unit to adjust the volume. The Volume dialog box appears on the screen for a few seconds.The VOLUME (+) button increases the volume, and the VOLUME ( – ) button decreases the volume.
22 MODE button Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Computer and press the SELECT button. COMPUTER MODE SELECTING COMPUTER MODE MENU OPERA TION When selecting the Computer Mode, the Current Mode display appears.
23 COMPUTER MODE COMP A TIBLE COMPUTER SPECIFICA TIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock. NOTE : Specifications are subject to change without notice.
24 COMPUTER MODE PC ADJUSTMENT This Projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by the Multi-Scan system of this projector.
25 COMPUTER MODE The number of the total vertical lines. Adjust the number to match the image of your personal computer. Total lines Recalls the parameter data that was previously adjusted. Reset Stores the parameters in the memory. Stored Clears the parameter data previously set.
26 COMPUTER MODE Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT button. Another dialog box PICTURE IMAGE ADJUSTMENT Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear.
27 COMPUTER MODE The Auto Image function is provided to automatically adjust Fine sync, Total dots, and Picture Position for most computers. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select AUTO IMAGE and press the SELECT button.
28 COMPUTER MODE PICTURE SCREEN ADJUSTMENT Move the arrow to the function and press the SELECT button. NOTE : The True and the Digital Zoom cannot be operated when “ RGB, ” “ HDTV1035i ” or “ HDTV1080i ” is selected on the SYSTEM MENU (P22 and 23).
29 MODE button VIDEO MODE Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Video and press the SELECT button. SELECTING VIDEO MODE DIRECT OPERA TION Select VIDEO mode by pressing the MODE button on the Top Control or the VIDEO button on the Remote Control Unit.
30 VIDEO MODE SELECTING COLOR SYSTEM Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Another dialog box VIDEO SYSTEM Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear.
31 VIDEO MODE PICTURE IMA GE ADJUSTMENT Each of the keys operates as follow. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT button. Another dialog box PICTURE IMAGE ADJUSTMENT Menu will appear.
32 SETTING SETTING MENU Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SETTING and press the SELECT button. Another dialog box SETTING Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear.
33 SETTING The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the lamp replacement monitor timer by using this function. (Refer to page 36.) Lamp age SELECTING LANGU A GE Press the MENU button and the ON-SCREEN MENU will appear.
34 APPENDIX OPERA TING WIRELESS MOUSE INST ALLA TION The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless mouse operation.
35 APPENDIX CLEANING THE PR OJECTION LENS Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. When the projector is not in use, replace the lens cover.
36 APPENDIX LAMP REPLA CEMENT When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is required. Turn off the projector and disconnect the AC plug.
37 APPENDIX TR OUBLESHOO TING Before calling your dealer or service center for assistance, check the matters below once again. 1. Make sure you have connected the projector to your equipment as described in the section "CONNECTING THE PROJECTOR" on pages 11 ~ 13.
38 This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards. APPENDIX W ARNING : High v oltages are used to operate this projector .
39 APPENDIX ● The specifications are subject to change without notice. 0.7 ” TFT Active Matrix type, 3 panels TECHNICAL SPECIFICA TIONS Multi-media Projector 5.
Printed in Japan Part No. 610 292 5494 (1AA6P1P2768-- MP6BA) © 2001 Eiki International, Inc. A udio Visual/Video Products EIKI INTERNA TIONAL, INC. 26794 Vista Terrace Drive, Lake Forest, CA. 92630-8113, U.S.A. TEL (949) 457-0200 FAX (949) 457-7878 865 Heritage Drive P.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Eiki LC-XM1 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Eiki LC-XM1 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Eiki LC-XM1, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Eiki LC-XM1 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Eiki LC-XM1, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Eiki LC-XM1.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Eiki LC-XM1. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Eiki LC-XM1 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
