Manuel d'utilisation / d'entretien du produit MP7640i/MP7740i du fabricant 3M
Aller à la page of 40
MP 7640i/MP 7740i Multimedia Projector Operator's Guide.
1 CONTENTS Thank you for purchasing this projector. • The information in this manual is subject to change without notice. • The manufacturer assumes no responsibility for any errors that may appear in this manual • The reproduction, transmission or use of this document or contents is not permitted without express written authority.
2 ● Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system ● Partial Magnification Function Interesti.
3 1 Connect your devices to the projector Connect your computer, VCR and/or other devices you will be using to the projector. Insert the batteries into the remote control 2 12 3 Connect the power cord (1) Connect the connector of the electrical power cord to the AC inlet of the main unit.
4 P ART NAMES THE PROJECTOR Indicates the corresponding reference page AC power inlet (to the Power Cord) 3 Ventilation Openings (Intake) Power switch Zoom ring 15 Focus ring 15 Remote sensor 13 Lens .
5 THE REMOTE CONTROL THE TERMINAL P ANEL STANDBY/ON button 14 VIDEO button 15 MENU button 23 10 RGB button 15 BLANK button 22 SEARCH button 22 VOLUME button 17 MUTE button 17 KEYSTONE button 20 ASPECT.
6 Angle Adjustment 1 Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle 2 Release the button to lock at the desired angle 3 Make the rear foot adjuster screw to adjust the left-right slope Use the foot adjusters on the bottom of the projector to adjust the projection angle.
7 Refer to the illustrations and tables below to determine the screen size and projection distance. Adjusting the Screen Size and Pr ojection Distance Top view a b Lens center The screen Side view Top.
8 DVD players 11 VCRs 11 Laptop computers 10 Desktop computers 10 Indicates the corresponding reference page ATTENTION Precautions to observe when connecting other devices to the projector • Whenever attempting to connect other devices to the projector, please thoroughly read the manual of each device to be connected.
9 Ports and Cables Refer to the table below to find out which projector port and cable to use for connecting a given device. Use this table for determining which cables to prepare. About Plug-and-Play Capability • This projector is compatible with VESA DDC 1/2B.
10 Laptop computer Desktop computer CONNECTING YOUR DEVICES (continued) Connecting to a Computer ATTENTION Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop's RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display).
11 DVD player VCR Connecting to a DVD Player Connecting to a VCR B C A If using a component video connection If using an audio/video connection COMPONENT VIDEO IN COMPONENT VIDEO OUT AUDIO/VIDEO IN AU.
1 Remove the battery cover Slide back and remove the battery cover in the direction of the arrow. Insert the batteries Align and insert the two AA batteries (that came with the projector) according to their plus and minus terminals (as indicated in the remote control).
13 • The remote control works with both the projector's front and rear remote sensors. • The range of the remote sensor on the front is 3 meters with a 90-degree range (45 degrees to the left and right of the remote sensor), and back is 3 meters with a 60-degree range.
14 1 Make sure that the power cord is firmly and correctly connected to the projector and outlet 2 Turn on the projector's power Set the power switch to [ | ] (ON). The projector will go to STANDBY mode and the POWER indicator will light to solid orange.
15 RGB 6 Use the zoom ring to adjust the screen size 7 Use the focus ring to focus the picture 5 If selecting RGB input Press the RGB button Press this button to swich to the devices connected to RGB IN as illustrated below.
16 VIDEO ASPECT MUTE KEYSTONE FREEZE OFF ON MENU POSITION ENTER ESC RESET VOLUME MAGNIFY AUT O BLANK RGB SEARCH ST ANDBY/ON 1 Press the STANDBY/ON button (control panel or remote control) The message "Power off?" will appear on the screen for approximately 5 seconds.
17 VIDEO ASPECT MUTE KEYSTONE FREEZE OFF ON MENU POSITION ENTER ESC RESET VOLUME MAGNIFY AUT O BLANK RGB SEARCH ST ANDBY/ON 1 Press the VOLUME button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume.
18 1 Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position. 2 Use the , , , buttons to adjust the position When you want to initialize the position, press the RESET button during adjustment.
19 The automatic adjustment operation requires approximately 10 seconds. Also, please note that it may not function correctly with some input signals. NOTE 1 USING THE AUT OMA TIC ADJUSTMENT FEA TURE Press the AUTO button Horizontal position (H. POSIT), vertical position (V.
20 • This function may not be work well with some types of input signals. • The adjustable range for correcting keystone distortions will vary with the type of input signal. NOTE CORRECTING KEYSTONE DIST ORTIONS 1 Press the KEYSTONE button As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion.
21 The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT, AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.
22 SIGNAL SEARCHING SELECTING THE ASPECT RA TIO TEMPORARIL Y BLANKING THE SCREEN 1 Press the SEARCH button When you press the SEARCH button, the projector begins searching for input signals. If it detects an input signal, the search will cease and the projector will project the detected signal.
23 USING THE MENU FUNCTIONS 1 Press the MENU button The menu display appears on the screen. The projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, SCREEN, and OPTION. Select a menu using the / buttons. The current settings of the items that can be manipulated via the selected menu appear.
MAIN Menu Item Description BRIGHT Adjust Brightness: Light ⇔ Dark CONTRAST Adjust Contrast: Strong ⇔ Weak ASPECT Select Aspect Ratio: At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT.
PICTURE-1 Menu PICTURE-2 Menu With the PICTURE-1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. With the PICTURE-2 menu, the four items shown in the Table below can be performed.
MUL TIFUNCTIONAL SETTINGS (continued) INPUT Menu With the INPUT menu, the four items shown in the Table below can be performed. With inputting of RGB IN signal, the horizontal and vertical frequencies of the signal will be displayed on the initial screen of the INPUT menu.
SCREEN Menu With the SCREEN menu, the two items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. 27 SCREEN Menu Item Description BLANK Selection of BLANK Screen: .. ⇔ . . ⇔ .
MUL TIFUNCTIONAL SETTINGS (continued) OPTION Menu With the OPTION menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.
29 THE LAMP HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately: 78-6969-9463-7 for MP7640i / 78-6969-9565-9 for MP7740i), then contact your local dealer.
30 • The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp. NOTE Replacing the lamp All projector lamps will wear out eventually.
THE AIR FIL TER Caring for the air filter The air filter should be cleaned about every 100 hours. If the LAMP indicator and TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned.
32 Replacing the air filter If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please contact your local dealer, after confirming the model of your separately sold replacement air filter. 1 Turn off the projector, and unplug the power cord.
OTHER CARE Caring for the inside of the projector : In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years. Never try to care for the inside of the unit yourself. Doing so is dangerous.
WHA T T O DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED Related Messages When the unit's power is ON, messages such as those shown below may be displayed.
WHA T T O DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued) Regarding the Indicator Lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the Table below. Please respond in accordance with the instructions within the Table.
Phenomena That May Easily Be Mistaken for Machine Defects Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.
Dimension Diagram Unit : mm 289 84 52.5 74.5 215 60 Item Specification Product name Liquid crystal projector Liquid crystal panel Panel size 1.8 cm (0.7 type) Drive system TFT active matrix Pixels MP7640i ： 480,000 pixels (800 horizontal x600 vertical) MP7740i ： 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens F=2.
38 Acccessories..................................................................................Part Number UHB lamp, 150W (MP7640i) ..........................................................78-6969-9463-7 UHB lamp, 150W (MP7740i) ...................
3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000 3M Canada P.O. Box 5757 London, Ontario N6A 4T1 3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico 3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France Litho in Japan © 3M 2002 78- 6970 -9166-4 Rev.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté 3M MP7640i/MP7740i c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du 3M MP7640i/MP7740i - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation 3M MP7640i/MP7740i, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le 3M MP7640i/MP7740i va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le 3M MP7640i/MP7740i, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du 3M MP7640i/MP7740i.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le 3M MP7640i/MP7740i. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei 3M MP7640i/MP7740i ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
