Manuel d'utilisation / d'entretien du produit BHT-7000 du fabricant Denso
Aller à la page of 175
User's Manual.
Copyright © DENSO, 2000 All rights reserved. No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher. Specifications are subject to change without prior notice. All products and company names mentioned are trademarks or registered trademarks of their respective holders.
i Pr eface Please READ through these operating instructions carefully. It will enable you to operate your BHT-7000 correctly. After you have finished reading the instructions, keep this manual handy for speedy reference.
ii How this book is organized This manual is made up of five chapters and appendices. Chapter 1. Quick Guide Describes the basic operating method of the BHT-7000 and the related notes.
iii ■ Technical Terms Used in This Manual Source Program and Object Program (User Program) Generally, a source program is translated into an object program by a compiler. This manual calls an object program a user program. BHT-BASIC This manual expresses BHT-BASIC3.
iv SAFETY PRECAUTIONS Be sure to observe all these safety precautions. ■ Please READ through this manual carefully. It will enable you to use the BHT-7000 and CU-7000 correctly.
v W ARNING Handling the battery cartridge • Never disassemble or heat the battery cartridge, nor put it into fire or water; doing so could cause battery-rupture or leakage of battery fluid, resulting in a fire or bodily injury.
vi W ARNING • Do not look into the laser beam source through the reading window or point the reading window towards the eyes. The laser beam emitted through the reading window is harmful to the eyes. • Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.
vii CAUTION Basic handling tips • Never put the BHT in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight. Doing so could affect the housing or parts, resulting in a fire.
viii CAUTION • If you drop the BHT so as to damage its hous- ing, immediately turn off the power, pull out the dry batteries or the battery cartridge, and contact your nearest dealer.
ix CAUTION Handling the CU • If you will not be using the CU for a long time, be sure to unplug the AC adapter from the wall socket for safety. Failure to do so could result in a fire. • When caring for the CU, unplug the AC adapter from the wall socket for safety.
x ■ Proper Care of the BHT and CU Clean the housing and the battery cartridge terminals with a dry, soft cloth. Before cleaning, be sure to power off the BHT and unplug the AC adapter of the CU. • Never use benzene, alcohol, or other or- ganic solvents.
xi FCC Regulations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
xii Content Overviews Preface ............................................................................................................................... .i How this book is organized ...............................................................
xiii Chapter 4. Error Messages .............................................................................................. 103 4.1 System Errors .......................................................................................................
Chapter 1. Quick Guide Chapter 2. Getting Started the BHT-7000 and System Mode Chapter 3. Communications Operations of BHT-7000 Chapter 4. Error Messages Chapter 5.
1 Chapter 1. Quick Guide Chapter 1 Quick Guide This chapter describes the basic operating method of the BHT-7000 and the related notes. 1.1 Reading Bar Codes ............................................................................... 2 1.2 Setting and Using the Hand Strap .
2 • If the BHT fails to read due to specular effects or other factors, change the scanning angle of the reading win- dow or the distance from codes as shown at right, and try it again. (Specular effects occur when the reflec- tion of the light from the bar code becomes exces- sively strong.
3 Chapter 1. Quick Guide 1.2 Setting and Using the Hand Strap ■ Setting the hand strap ■ Using the hand strap Put your hand through the hand strap and hold the BHT as shown below.
4 1.3 Setting the Backlight Pressing the M1 key while holding down SF (Shift) key activates or deactivates the backlight function. Press M1 while holding down SF . Backlight ON If no key is pressed for at least 3 seconds. Backlight OFF (The backlight function is kept ON.
5 Chapter 1. Quick Guide 1.4 Using the Keypad ■ Entering Numerical Data To enter numerical data, e.g., the quantity of goods, use the ten numerical keys and the ENT key. For example, to enter the number "120," press the 1 , 2 and 0 keys and then press the ENT key.
6 1.5 Communicating via the Optical In- terface ■ Optical Communications with the BHT-7000 The BHT-7000 communicates using an IR beam, so make sure that there is no obstruc- tion in the light path between the BHT-7000 and any target stations.
7 Chapter 2. Getting Started the BHT-7000 and System Mode Chapter 2 Getting Started the BHT -7000 and System Mode This chapter summarizes the BHT-7000 system configuration and describes the opera- tion including preparation and System Mode (which is required for the efficient use of application programs).
8 2.1 BHT -7000 System Configuration The BHT-7000 barcode data collection system requires the following hardware as well as the BHT-7000 Bar Code Handy Terminal (which reads bar codes and accepts keyp.
9 Chapter 2. Getting Started the BHT-7000 and System Mode ■ CU-7000 and RS-232C Interface Cable (option) The CU-7000 is an IrDA-compliant communications unit which is required when your host computer is not equipped with an IrDA interface port.
10 ■ Ir-Transfer Utility E (option) Running on the host computer, this utility transfers files between the BHT-7000 and the host computer. For its file transfer control procedure, the utility uses the BHT-Ir protocol. (For the details about the BHT-Ir protocol, refer to Chapter 3, Subsection 3.
11 Chapter 2. Getting Started the BHT-7000 and System Mode Software Structure System Program and JIS Level 1 & Level 2 fonts are resident in the system area and user area, respectively. To use extension programs and user programs, you should download the program files into the user area.
12 System Mode System Mode is a system program exclusively designed for the effective use of user programs in the BHT-7000. It sets up the execution environments for those programs; e.g., it prepares downloading/uploading conditions, sets the calendar clock, and tests the BHT-7000 components including the LCD, beeper, and keypad.
13 Chapter 2. Getting Started the BHT-7000 and System Mode 2.2 Infrar ed Communications The BHT-7000 has an integrated infrared (IR) communications device which enables wireless transfer of programs and data between the BHT-7000 and the host computer and between the BHT-7000s, instead of the conventional wire transfer.
14 The BHT-7000's physical layer complies with the IrDA1.0, with a maximum transfer distance of 0.8 m and maximum transmission rate of 115.2 kbits per second. The BHT-7000 adopts the exclusive BHT-Ir protocol which allows you to develop user programs for IR communications in BHT-BASIC, as can be done with conventional wire communications.
15 Chapter 2. Getting Started the BHT-7000 and System Mode 2.3 Components and Functions Indicator LED Illuminates in green when the BHT has successfully read the bar codes. Liquid crystal display (LCD) Shows the characters and graphic patterns. Trigger switch (M3 key)* Press this switch to start bar-code reading.
16 The functions of the keys may be set by user programs. Shown below is a set of sample functions. Function keys Used for choosing functions. M1/M2 (Magic) keys Used as any of the ENT key, trigger switch, SF key, and backlight function on/off key depending upon definition in System Mode or in user programs.
17 Chapter 2. Getting Started the BHT-7000 and System Mode 26-key pad BS (Backspace) key Moves back one character. PW (Power) key Turns the BHT on or off. M1/M2 (Magic) keys Used as any of the ENT key, trigger switch, SF key, and backlight function on/off key depending upon definition in System Mode or in user programs.
18 2.4 Pr eparation 2.4.1 Setting-up 1: Loading the Battery Cartridge Before the first use of the BHT-7000, be sure to load the battery cartridge as shown below. The battery cartridge is not loaded in the BHT-7000 when shipped from the factory. (1) To use the rechargeable battery cartridge, charge it.
19 Chapter 2. Getting Started the BHT-7000 and System Mode NOTE NOTE NOTE Never charge the dry battery cartridge. The BHT-7000 has an integrated backup power source which backs up the memory and calendar clock in the BHT-7000 when no battery cartridge is loaded or the voltage level of the battery cartridge drops below the specified level.
20 ■ Low Battery Indication Low battery indication—Level 1 If the battery output voltage drops below a specified lower level limit while the BHT- 7000 is in operation, the BHT-7000 displays the following level 1 message for approx. 2 seconds and beeps three times.
21 Chapter 2. Getting Started the BHT-7000 and System Mode W ARNING Only use the dedicated charger (CU-7000, C-700, or C-750) for charging the lithium-ion battery cartridge. Using a different type of charger could cause battery-rupture or leakage of battery fluid and result in a fire, bodily injury, or serious damage to property.
22 (1 ) While holding down the SF and 1 keys, press the PW key to start System Mode. The SYSTEM MENU shown at left will appear. (2) Press the 4 key to select the "SET SYSTEM" on the SYSTEM MENU and then press the ENT key, and the screen shown at left will appear.
23 Chapter 2. Getting Started the BHT-7000 and System Mode (3) Press the 3 key on the SET SYSTEM screen to select the "DATE/TIME" and then press the ENT key, and the screen shown at left will appear. (4) Use the numerical keys to enter the year (only the last two digits), month, day, hour, and minute in this order.
24 2.4.3 Adjusting the LCD Contrast & Beeper V olume, Switching the Beeper & V ibrator , and Checking the Battery V oltage Level [ 1 ] Adjusting the LCD Contrast & Beeper V olume and Switching the Beeper & V ibrator While holding down the M1 or M4 key, press the PW key, and any of the following screens will appear on the LCD.
25 Chapter 2. Getting Started the BHT-7000 and System Mode Adjusting the LCD contrast You can adjust the LCD brightness to 8 contrast levels. 1) Use the * or * keys to select the LCD CONTRAST line. 2) To decrease the contrast, press the * key; to increase it, press the * key.
26 [ 2 ] Checking the Battery V oltage Level The battery voltage level is always displayed on the status indicator line (bottom line). The displayed battery level shows the terminal voltage of the battery, not how much power is left. The battery voltage level varies depending upon the operation of the BHT-7000, so the displayed level also may vary.
27 Chapter 2. Getting Started the BHT-7000 and System Mode 2.4.4 Battery Replacement Notes ■ When is battery replacement needed? If the "Charge the battery!" or "Replace the batteries!" appears on the LCD, replace the battery cartridge with a fully charged one or replace the dry batteries with new ones, respectively.
28 (2) When powering on the BHT after storage with no battery cartridge loaded: Even after removal of the battery cartridge, the calendar clock will work with the backup power source for a while.
29 Chapter 2. Getting Started the BHT-7000 and System Mode 2.5 Initializing the BHT -7000 System Initializing the system will lose program files and data files stored in the user area and the system settings will revert to the factory defaults. You need to initialize the system when: (1) you want to delete all of the program files and data files.
30 (1) Selecting the memory area to be initialized Press the PW key while holding down the SF , M1 and 0 keys together. The screen shown at left will appear. To initialize the user area except for the font file area, press the ENT key. The screen switches to the confirmation display given in step (3) below.
31 Chapter 2. Getting Started the BHT-7000 and System Mode (3) Confirming the memory area selected for initialization Selecting the "USER AREA EXCEPT FONTS" in step (1) above will call up the confirmation screen shown at left. 1 Yes : Starts initialization.
32 (5) Completion of initialization Upon completion of the initialization, the BHT-7000 displays the screen shown at left for a second and turns itself off automatically. Do not power off the BHT-7000 until the above initialization completion screen appears.
33 Chapter 2. Getting Started the BHT-7000 and System Mode 2.6 Operating in System Mode System Mode is an operating software exclusively designed for the effective use of the BHT-7000, which includes various functions as shown on the following pages. 2.
34 ■ Structure of System Mode SYSTEM MENU ⇐ Press the PW key while holding down the SF and 1 keys. System Environment Setting Sets a variety of environmental condi- tions—an execution program, m.
35 Chapter 2. Getting Started the BHT-7000 and System Mode System Information Shows the system program version, memory size, system message version, and font type and version (Refer to Subsection 2.
36 In addition to the functions given on the previous page, System Mode has these four functions: Deleting files, Downloading/uploading the BHT system parameter file, Set- ting the remote wake-up parameters, and Downloading/uploading the system mes- sage file.
37 Chapter 2. Getting Started the BHT-7000 and System Mode 2.6.2 Operating in System Mode Some functions in System Mode require several screens to be shifted, as shown in the example below.
38 Press 2 or use * and * to select the desired set item. [ 2 ] Selecting a desir ed setting First, select a desired item on the current screen by using the numerical key or the cursor keys ( * and * ) so as to highlight the desired item. Use the * and * keys to select a desired setting and then press the ENT key.
39 Chapter 2. Getting Started the BHT-7000 and System Mode 2.6.3 Detailed Description of the Functions in System Mode [ 1 ] Pr ogram Execution Selecting "1:EXECUTE PROGRAM" on the SYSTEM MENU shows the screen shown at left.
40 Selecting "2: DOWNLOAD" on the SYSTEM MENU calls up the screen shown at left. 1 FILE : Downloads a user program file or data file to the user area of the BHT-7000. 2 HT<-->HT COPY : Downloads all of the files, system parameters, and cal- endar clock data stored in the connected BHT-7000.
41 Chapter 2. Getting Started the BHT-7000 and System Mode With this screen displayed, the BHT-7000 waits for a file to be downloaded. If you select "2:HT<-->HT" on the DOWNLOAD menu, the "HT<-->HT" will appear in the center of the 2nd line.
42 DOWNLOAD FILE XXXXXXXX.XXX Out of memory!! Retry? 1:Yes 2:No DOWNLOAD FILE XXXXXXXX.XXX Too many files!! Retry? 1:Yes 2:No DOWNLOAD FILE XXXXXXXX.XXX Communication error!! Retry? 1:Yes 2:No If an e.
43 Chapter 2. Getting Started the BHT-7000 and System Mode ■ Problem You attempted to download an invalid program file. ■ Solution Check whether the program file you attempted to download is available to your BHT model. If it is not available, download the appropriate program.
44 [ 3 ] Uploading Selecting "3: UPLOAD" on the SYSTEM MENU calls up the screen shown at left. 1 ONE FILE : Uploads a user program file or data file stored in the memory. 2 ALL FILES : Uploads all user program files (object programs) and all data files stored in the memory.
45 Chapter 2. Getting Started the BHT-7000 and System Mode If you select "1:ONE FILE" or "2:ALL FILES" on the UPLOAD menu when no files are stored in the memory, the message shown at left will appear. Pressing the C key returns to the UPLOAD menu.
46 If an error occurs during uploading If some error occurs during uploading, one of the following screens will appear and the beeper beeps three times. To retry the uploading operation, press the 1 and ENT keys; to abort it, press the 2 and ENT keys.
47 Chapter 2. Getting Started the BHT-7000 and System Mode [ 4 ] System Environment Setting Selecting "4: SET SYSTEM" on the SYSTEM MENU calls up the screen shown at left. 1 EXECUTE PROGRAM : Sets an execution pro- gram to be run when the power is turned on.
48 [4.2] Setting the message version [4.1] Setting an execution program Selecting "1: EXECUTE PROGRAM" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. Use the * and * keys to move the cursor to a desired execution program to be run when the power is applied, and then press the ENT key.
49 Chapter 2. Getting Started the BHT-7000 and System Mode [4.3] Setting the calendar clock Selecting "3: DATE/TIME" on the SET SYSTEM menu calls up the screen shown at left. Use the numerical keys to enter the year (only the last two digits), month, day, hour, and minute in this order, and then press the ENT key.
50 Selecting "4: BARCODE" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. 1 INVERT : A ctivates or deactivates the black-and-white inverted la- bel reading function. 2 DECODE LEVEL : Sets the decode level.
51 Chapter 2. Getting Started the BHT-7000 and System Mode Minimum number of digits to be read for ITF, STF, or CODABAR (MINIMUM DIGITS) You may determine the minimum number of digits to be read for ITF, STF, and CODABAR.
52 [4.5] Setting the communications environments After the BHT-7000 is initialized, the interface port and communications parameters are set as listed in the default table below. Do not access them unless necessary. Listed below are the default communications parameters for the direct-connect inter- face.
53 Chapter 2. Getting Started the BHT-7000 and System Mode Selecting the "5: COMMUNICATION" on the SET SYSTEM menu calls up the screen shown at left. 1 OPTICAL: Switches to the communi- cations parameters setting screen for the optical inter- face .
54 (1) Communications parameters setting screen Selecting "1:PARAMETER" on the SET OPTICAL screen calls up the screen shown at left. Highlighted is the current setting. Select the desired transmission speed by using the numerical keys or * and * keys, and then press the ENT key.
55 Chapter 2. Getting Started the BHT-7000 and System Mode [4.5-2] Setting the communications parameters for the direct-connect interface Selecting "2:CONNECTOR" on the SET COMMUNI- CATION menu calls up the screen shown at left. 1 PARAMETER: Switches to the commu- nications parameters set- ting screen.
56 (2) Communications protocol option menu Selecting "2:PROTOCOL" on the SET CONNECTOR screen calls up the screen shown at left. Highlighted is the current setting. 1 SERIAL No.: Selects whether or not the system will add serial num- bers to data blocks.
57 Chapter 2. Getting Started the BHT-7000 and System Mode [4.5-3] Setting the interface port Selecting the "3:COM PORT" on the SET COMMU- NICATION menu calls up the screen shown at left.
58 [4.5-4] Setting the communications protocol type Selecting the "4:PROTOCOL TYPE" on the SET COMMUNICATION menu calls up the screen shown at left. Highlighted is the current setting. 1 BHT Protocol: Selects the BHT-protocol for downloading or uploading files in System Mode or for the execution of XFILE state- ment in BHT-BASIC.
59 Chapter 2. Getting Started the BHT-7000 and System Mode [4.6] Defining the functions of the shift key and magic keys Selecting the "6:KEY" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. 1 SHIFT KEY: Switches to the shift key defini- tion screen.
60 Selecting the "2:M1 KEY," "3:M2 KEY," "4:M3 KEY" or "5:M4 KEY" on the SET KEY menu calls up the screen as shown at left. (This example appears when the "4:M3 KEY.") Highlighted is the current setting.
61 Chapter 2. Getting Started the BHT-7000 and System Mode [4.7] Setting the resume function Selecting "7: RESUME" on the SET SYSTEM menu calls up the screen shown at left.
62 [ 5 ] T esting Selecting "5: TEST" on the SYSTEM MENU calls up the screen shown at left. 1 BARCODE : Selects the bar-code reading test. 2 MEMORY : Selects the RAM read/write test. 3 BEEPER : Selects the beeper scale test. 4 AGING : Selects the aging test.
63 Chapter 2. Getting Started the BHT-7000 and System Mode [5.1] Bar -code reading test Selecting "1: BARCODE" on the TEST menu calls up the screen shown at left. Actually read bar codes with the BHT-7000 and check the read data displayed on the LCD.
64 [5.2] Memory test Selecting "2:MEMORY" on the TEST menu calls up the screen shown at left, and then starts writing and reading onto/from all areas of the RAM as well as checking the address.
65 Chapter 2. Getting Started the BHT-7000 and System Mode [5.3] Beeper scale test Selecting "3:BEEPER" on the TEST menu calls up the screen shown at left and makes the beeper sound at three octaves listed below. Upon completion of this test, the BHT-7000 auto- matically returns to the TEST menu.
66 Selecting "5:LCD" on the TEST menu calls up the test pattern shown at left on the LCD and turns on the indicator LED in green. Each time the ENT key is pressed, the screen shifts to the next test pattern. To return to the previous screen, press the BS key.
67 Chapter 2. Getting Started the BHT-7000 and System Mode The fine checker pattern appears. The fine checker pattern is reversed. Two right-angled triangles appear.
68 The file name, file size, and test result (OK or NG) appear as shown at left. Press the C key to return to the file selection screen. If a defective file is found, delete it or overwrite it with the same name file. Even defective, the file can be uploaded on the UPLOAD menu.
69 Chapter 2. Getting Started the BHT-7000 and System Mode [5.7] Communications test In System Mode, you may test the optical interface port and direct-connect interface port.
70 Testing the optical interface port Selecting the "1:OPTICAL" on the TEST COMMU- NICATION menu calls up the screen shown at left. At the slave BHT-7000 to be tested, select the "1:SLAVE" and at the master BHT-7000, select the "2:MASTER.
71 Chapter 2. Getting Started the BHT-7000 and System Mode If any error occurs, the BHT-7000 beeps three times and shows the screen at left. In parentheses are error codes which have the following meanings: ( X X) 1: The received data is different from the sent data.
72 [5.8] Key entry & beeper test Selecting "8:KEY & VIBRATION" on the TEST menu calls up the screen shown at left and makes the BHT-7000 ready for entry from the keypad.
73 Chapter 2. Getting Started the BHT-7000 and System Mode TEST KEY & BEEPER & VIBRATION IJK NLMO 7894561230.= ABCDEFGH After all keys are pressed and displayed on the LCD, this test automatically ends and the screen returns to the TEST menu. To stop this test, turn the power off.
74 [ 6 ] System Information Selecting the "6:VERSION" on the SYSTEM MENU calls up the screen shown at left, displaying the system program version, ROM and RAM sizes, sys- tem message version, and font types and their versions. Press the C key to return to the SYSTEM MENU.
75 Chapter 2. Getting Started the BHT-7000 and System Mode If no file is resident in the memory, the message shown at left appears. Press the C key to return to the file deletion menu. File selection screen Pressing the 0 key while holding down the SF key on the SYSTEM MENU calls up the screen shown at left.
76 Pressing the 3 key while holding down the SF key on the SYSTEM MENU calls up the screen shown at left. 1 DOWNLOAD: Downloads the BHT system pa- rameter file to the user area of the BHT-7000. 2 UPLOAD: U pl oads the BHT system pa- rameter file stored in the BHT- 7000.
77 Chapter 2. Getting Started the BHT-7000 and System Mode DOWNLOAD Out of memory!! Retry? 1:Yes 2:No DOWNLOAD File mismatch!! Retry? 1:Yes 2:No DOWNLOAD Too many files!! Retry? 1:Yes 2:No DOWNLOAD __.
78 ⇓ ⇓ UPLOAD ** Waiting ** UPLOAD __BHT.SYS ** Loading ** XXXXX/YYYYY UPLOAD __BHT.SYS ** Completed ** [8.2] Uploading the BHT system parameter file Selecting "2:UPLOAD" on the SYSTEM PARAM- ETER menu calls up the screen shown at left. With this screen displayed, the BHT-7000 waits for the BHT system parameter file to be uploaded.
79 Chapter 2. Getting Started the BHT-7000 and System Mode If an error occurs during uploading If some error occurs during uploading, one of the following screens will appear and the beeper beeps three times. To retry the uploading operation, press the 1 and ENT keys; to abort it, press the 2 and ENT keys.
80 [ 9 ] Setting the Remote W akeup SET REMOTE WAKEUP 1:REMOTE WAKEUP ON OFF 2:TRANSMIT SPEED 9600 19200 38400 57600 115200 Pressing the 4 key while holding down the SF key on the SYSTEM MENU calls up the screen shown at left. 1 REMOTE WAKEUP: Act i vates or deactivates the remote wakeup func- tion.
81 Chapter 2. Getting Started the BHT-7000 and System Mode [ 10 ] Downloading/Uploading the System Message File ⇓ SYSTEM MESSAGE 1:DOWNLOAD 2:UPLOAD DOWNLOAD _SYSMSG.
82 If an error occurs during uploading If some error occurs during downloading, the BHT-7000 beeps three times and shows one of the following screens with the prompt "Retry?": To retry the download, press the 1 and ENT keys; to abort it, press the 2 and ENT keys.
83 Chapter 2. Getting Started the BHT-7000 and System Mode [10.2] Uploading the system message file ⇓ ⇓ UPLOAD ** Waiting ** UPLOAD _SYSMSG.FN3 ** Loading ** XXXXXXX/YYYYYYY UPLOAD _SYSMSG.FN3 ** Completed ** Selecting "2:UPLOAD" on the SYSTEM MESSAGE menu calls up the screen shown at left.
84 If an error occurs during uploading If some error occurs during uploading, one of the following screens will appear and the beeper beeps three times. To retry the uploading operation, press the 1 and ENT keys; to abort it, press the 2 and ENT keys.
85 Chapter 3. Communications Operations of BHT-7000 Chapter 3 Communications Operations of BHT -7000 This chapter describes the communications operations of the BHT-7000--the RS-232C interface specifications, the basic communications specifications, and the communica- tions protocols--for data transmission with the host computer or other devices.
86 3.1 RS-232C Interface Specifications [ 1 ] Interface Connector and Pin Assignment The BHT-7000 has a direct-connect interface port which is connectable to the 3-pole mini stereo plug (ø2.5 mm or 0.1") and supports a subset of the RS-232C interface as shown below.
87 Chapter 3. Communications Operations of BHT-7000 [ 2 ] Interface Cable Connection Connect the BHT-7000 directly to a host computer, a modem, or a printer with a direct- connect interface cable as illustrated below.
88 3.2 Basic Communications Specifica- tions and Parameters 3.2.1 Basic Communications Specifications Listed below are the communications specifications when the BHT-7000 exchanges data with a host computer through the CU-7000 (optical interface) or direct-connect interface cable.
89 Chapter 3. Communications Operations of BHT-7000 ■ Transmission Code and Bit Order All characters should be coded to 7- or 8-bit code for data transmission. The standard data exchange code of the BHT-7000 is JIS 7- or 8-bit code. The transmis- sion bit order is LSB (Least significant bit) first.
90 3.2.2 Communications Parameters In System Mode and user programs written in BHT-BASIC, you may set the communi- cations parameters listed below. Transmission Speed 2400, 9600, 19200, 38400, 57600, .
91 Chapter 3. Communications Operations of BHT-7000 3.3 Communications Pr otocols The BHT-7000 supports both the BHT-protocol and the BHT-Ir protocol for file trans- mission. 3.3.1 BHT -pr otocol [ 1 ] Overview The BHT-protocol is the communications procedure used to transmit files between the BHT-7000 and a host (or between the BHT-7000s).
92 [ 2 ] Control Characters The control characters are classified into two groups: transmission control characters and text control characters. (1) T ransmission control characters The transmission control characters listed below are used to compose transmission control sequences in phases 1 through 3.
93 Chapter 3. Communications Operations of BHT-7000 (2) T ext control characters The text control characters are used to format transmission texts. In the BHT-protocol, they include the following headers and a terminator. Symbol Value Meaning Function SOH 01h Start Of Heading Indicates the start of heading text (Phase 2).
94 S O H E T X B C C S T X E T X B C C S T X E T X B C C [ 3 ] Basic Format of T ransmission Messages Basically, the BHT-7000 transmits data as units of a file. First, it transmits a heading text which includes the attribute information of a file (e.g.
95 Chapter 3. Communications Operations of BHT-7000 123 4 0D 0A 0 0 0 0 0 0 11 7 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PR O G 1 . P D3 0 0 52 3 [ 4 ] T ext Format Text should be formatted according to the standard of the BHT-protocol before trans- mission.
96 1 2 3 4 5 6 7 8 9 1 01 11 21 31 41 51 61 71 81 92 02 1 M A S T E R D A T 00592 n 06 10 . T100 91 S1 2 3 9202141325 ■ Data Text Format (1) Heading text Data field 1 Data field 2 Data field n Example of contents If a data field is less than the maximum digits in length, the lower blank bytes will be filled with space characters.
97 Chapter 3. Communications Operations of BHT-7000 3.3.2 BHT -Ir Pr otocol [ 1 ] Overview The BHT-Ir protocol is the communications procedure for the serial infrared link, which is used to transmit files between the BHT-7000 and a host (or between the BHT-7000s).
98 [ 2 ] Contr ol Characters The control characters are classified into two groups: transmission control characters and text control characters. (1) T ransmission control characters The transmission control characters listed below are used to compose transmission control sequences in phases 1 through 3.
99 Chapter 3. Communications Operations of BHT-7000 (2) T ext contr ol characters The text control characters are used to format transmission texts. In the BHT-Ir protocol, they include the following headers and a terminator. Symbol Value Meaning Function DLE SOH 1001h Start Of Heading Indicates the start of heading text (Phase 2).
100 S O H E T X C R C S T X E T X C R C S T X E T X C R C D L E D L E D L E D L E D L E D L E I D I D I D (2 bytes) (5 bytes) • • • • • • [ 3 ] Basic Format of T ransmission Messages Basically, the BHT-7000 transmits data as units of a file.
101 Chapter 3. Communications Operations of BHT-7000 123 4 0D 0A 0 0 0 0 0 0 11 7 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PR O G 1 . P D3 0 0 52 3 [ 4 ] T ext Format Text should be formatted according to the standard of the BHT-Ir protocol before transmission.
102 1 2 3 4 5 6 7 8 9 1 01 11 21 31 41 51 61 71 81 92 02 1 MA S T E R . D A T 00592 n 00 54 6 2 22 T100 91 S1 2 3 9202141325 ■ Data Text Format (1) Heading text Every data field should be 1 to 254 digits in length. If it is less than 3 digits, the upper blank bytes will be filled with zeros (0).
103 Chapter 4. Error Messages This chapter lists the error messages which will appear on the LCD if some error occurs in the BHT-7000. 4.1 System Errors ....................................................................................... 104 4.2 Errors in System Mode .
104 4.1 System Err ors If some error occurs when the power is turned on or during program execution, one of the following error messages will appear on the LCD.
105 Chapter 4. Error Messages Charge the battery! Replace the batteries! (When the dry battery cartridge is loaded) (When the rechargeable battery cartridge is loaded) Low battery indication—Level 2 ■ Problem When the power is turned on or during execution of program (System Mode or application), the bat- tery output level has lowered.
106 Set the current date and time. 00/01/01 00:00 _ / / : Reload the battery to restart! XXXXXXXX 01 Reload the battery to restart! tskid:XXXXXXXX ercd :XXXXXXXX addr :XXXXXXXX 02 Calendar clock stopp.
107 Chapter 4. Error Messages No execution program selected. Contact your administrator. Resume failure! Program restarts automatically. Execution program not selected ■ Problem No user program has been selected as an execu- tion program to be run when the power is turned on.
108 Reload the battery to restart! E:xxxxxxxx-F:xxxxxxxx 1:xxxxxxxx-2:xxxxxxxx P:xxxxxxxx-R:xxxxxxxx Your settings in System Mode have been lost. Will reset to defaults. Error in System Mode settings ■ Problem Your settings made in System Mode contain an er- ror.
109 Chapter 4. Error Messages Contact your administrator. Note the error number. (XXXX) System administrator to be called ■ Problem Any of the following errors has occurred: (1) Hardware error or ca.
110 4.2 Err ors in System Mode If some error occurs during operation in System Mode, one of the following error messages will appear on the LCD. When selecting a program file or data file ■ Problem You attempted to execute a user program in the EXECUTE PROGRAM menu, even though no user program files had been stored in the memories.
111 Chapter 4. Error Messages DELETE FILE ****************** * NO FILE EXISTS * ****************** DOWNLOAD FILE XXXXXXXX.XXX Out of memory!! Retry? 1:Yes 2:No DOWNLOAD File mismatch!! Retry? 1:Yes 2:No ■ Problem You have deleted all of the files stored in the memory in the DELETE FILE menu.
112 DOWNLOAD FILE XXXXXXXX.XXX Communication error!! Retry? 1:Yes 2:No DOWNLOAD FILE XXXXXXXX.XXX Program file error!! Retry? 1:Yes 2:No DOWNLOAD FILE XXXXXXXX.XXX Too many files!! Retry? 1:Yes 2:No ■ Problem The current download will exceed the maximum of 80 files in the memory.
113 Chapter 4. Error Messages UPLOAD FILE File error!! Upload? 1:Yes 2:No UPLOAD FILE XXXXXXXX.XXX Communication error!! Retry? 1:Yes 2:No UPLOAD Out of memory!! UPLOAD Too many files!! During uploading of a program file, data file, BHT system parameter file, or sys- tem message file ■ Problem The file you attempted to upload is damaged.
114.
115 Chapter 5. Handling the CU-7000 (Option) Chapter 5 Handling the CU-7000 (Option) This chapter describes the handling procedure of the CU-7000, the interfacing with the host computer, and the charging of the lithium-ion battery cartridge. 5.1 Functions of the CU-7000 .
116 5.1 Functions of the CU-7000 The optical communications unit CU-7000 is available in two models: CU-7001 and CU- 7002. The CU-7001 has both of functions (1) and (2) given below; the CU-7002 has only function (1). (1) Data exchange function The CU-7001/CU-7002 exchanges data and programs between the BHT-7000 and the host computer.
117 Chapter 5. Handling the CU-7000 (Option) 5.3 Applying Power to the CU-7000 Apply power to the CU-7000 by connecting it to the wall socket via the dedicated AC adapter according to the steps given below.
118 5.4 Communicating with the Host Computer 5.4.1 Setting the T ransmission Speed of the CU-7000 Set the transmission speed of the CU-7000 to the same value as that of the BHT-7000 and the host computer, by using the DIP switch provided on the bottom of the CU- 7000.
119 Chapter 5. Handling the CU-7000 (Option) 5.4.3 Interfacing with the Host Computer This section describes how to start communication with the host computer in System Mode. The same may apply when you use a user program. (1) Power on the host computer.
120 5.5 Charging the Lithium-ion Battery Cartridge (using the CU-7001) You may charge lithium-ion battery cartridges loaded in the BHT-7000. Service Life of Lithium-ion Battery Cartridge: Lithium-ion .
121 Chapter 5. Handling the CU-7000 (Option) Operator's Action Place the BHT-7000 on the CU-7001. ⇓ After approx. 4 hours ⇓ Remove the BHT-7000.
122 5.6 RS-232C Interface Specifications [ 1 ] Interface Connector and Pin Assignment The CU-7000 has an RS-232C interface port (Dsub-25S). RS-232C interface port (Dsub-25S) on the CU-7000 Pin No.
123 Chapter 5. Handling the CU-7000 (Option) [ 2 ] Interface Cable Connection As illustrated below, connect the CU-7000 (on which the BHT-7000 is put) to a host computer with a cross-mode cable.
124.
125 Appendices Appendices Appendix A. Specifications .......................................................................... 126 A.1 BHT-7000 .............................................................................................. 126 [ 1 ] Product Specifications .
126 Appendix A. Specifications A.1 BHT -7000 [ 1 ] Pr oduct Specifications Power Source Main power • Rechargeable lithium-ion battery cartridge (3.6 VDC) or • Dry battery cartridge (two alkaline manga- nese batteries LR6s) Dimensions 70 x 195 x 51 mm (W) x (L) x (H) (2.
127 Appendices Screen mode Font size Chars x Lines Dots (W x H) Single-byte Standard-size 21 x 8 6 x 8 ANK* mode Small-size 21 x 10 6 x 6 Two-byte 16-dot font Full-width 8 x 4 16 x 16 Kanji mode Half-.
128 0.26 mm (10.24 mils) 0.8 magnification min. 0.125 mm min. (4.9 mils min.) PCS value ≥ 0.75 Reflection intensity difference between white and black bars ≥ 0.4 0.15 mm min. (5.91 mils min.) (PCS value ≥ 0.45) (2) Optical Properties Required for Bar Code Labels White bars: Reflection intensity 45% min.
129 Appendices (3) Bar Code Label Size Recommended width: 10 mm min. (0.39 inch min.) Length: Depth of field (Distance from bar codes to the bar-code reading window) Length of labels (including margins) 460 mm max. (18.11 inches max.) (Minimum narrow bar width: 1.
130 [ 3 ] Interface Specifications Optical Interface Synchronization: Start-stop Input signals: RD Output signals: SD Transmission speed: 115,200 bps max. Direct-connect Interface Synchronization: Start-stop Transmission speed: 115,200 bps max. Signal level: Conforms to the RS-232C interface Pin assignment: As shown below.
131 Appendices A.2 CU-7000 [ 1 ] Pr oduct Specifications Power Source - Europe 230 VAC, 16 VA - U.S. 120 VAC, 13 VA - Australia 10 to 18 VDC, 450 mA (on 12 VDC) Power Consumption 8 VA Dimensions 112 x 148 x 84 mm (W) x (L) x (H) (4.41 x 5.83 x 3.31 inches) Weight CU-7001: Approx.
132 Signal Input/Output External device [ 3 ] Interface Specifications RS-232C Interface Port (Dsub-25S) on the CU-7000 25 13 14 1 1 FG Frame ground — 2 SD Send data → 3 RD Receive data ← 4 RS R.
133 Appendices ENQ S O H ACK ACK ACK ACK ACK EOT ACK E T X B C C S T X E T X B C C S T X E T X B C C S T X E T X B C C Establishment of Data Link (Phase 1) Heading text Data text n-1 Serial number Ser.
134 ACK ENQ 3 seconds 3 seconds ENQ ENQ ENQ ACK Data transmission may accidentally involve various types of errors. The BHT-protocol is designed to recover from those errors as frequently as possible. What follows is the BHT-protocol for phases 1 through 3.
135 Appendices ■ Abnormal termination of phase 1 (Abort of phase 1) If the sending station receives no ACK from the receiving station after sending an ENQ 10 times in succession, it sends an EOT to the receiving station after three seconds from the 10th ENQ to terminate the message transmission abnormally.
136 Phase 2: Data Transmission ■ Normal phase 2 The sending station first sends a transmission block containing the heading text. Each time the sending station receives an ACK from the receiving station, it sends a transmission block containing the data texts as shown below.
137 Appendices NAK NAK NAK NAK NAK ACK ■ Phase 2 with NAK If the sending station receives a NAK from the receiving station in response to a transmission block containing text data m, it sends that transmission block again immediately as shown below.
138 EOT 3 seconds 3 seconds ENQ ENQ ACK ■ Phase 2 with EOT If the sending station receives an EOT anytime during phase 2, it shifts to phase 3 to terminate the message transmission abnormally. Even if the phase 3 terminates normally, the transmission results in an abnormal end.
139 Appendices EOT ACK 3 seconds 3 seconds ENQ (1) ENQ (2) EOT ENQ (9) 3 seconds ■ Abnormal termination of phase 2 (Abort of phase 2) If the sending station receives no ACK from the receiving statio.
140 EOT (1) EOT (2) EOT (3) 3 seconds 3 seconds EOT (10) 3 seconds or more ACK EOT EOT EOT 3 seconds 3 seconds ■ Phase 3 with iterated EOT transmission due to no response or invalid response If the .
141 Appendices [ 2 ] Aborting Data T ransmission Pressing the C key aborts data transmission. If the C key is pressed during downloading, the BHT-7000 transmits an EOT and aborts the file transmission. If it is pressed during uploading, the BHT-7000 transmits the current transmission block followed by EOT and then aborts the file transmission.
142 S T X E T X B C C [ 3 ] BCC for Horizontal Parity Checking To check whether data has been transmitted accurately, the BHT-7000 supports hori- zontal parity checking for every transmission block. In horizontal parity checking, a horizontal parity byte so called BCC (Block Check Character) is suffixed to an ETX of every transmission block.
143 Appendices B.2 BHT -Ir pr otocol [ 1 ] T ransmission Control Sequences Shown below is a typical message transmission sequence supported by the BHT-Ir protocol.
144 Data transmission may accidentally involve various types of errors. The BHT-Ir proto- col is designed to recover from those errors as frequently as possible.
145 Appendices ■ Abnormal termination of phase 1 (Abort of phase 1) If the sending station receives no sequence of DLE ACK and IDs from the receiving station after sending a sequence of DLE ENQ and IDm 60 times in succession, it sends a sequence of DLE EOT and IDm to the receiving station after 0.
146 Phase 2: Data Transmission ■ Normal phase 2 The sending station first sends a transmission block containing the heading text. Each time the sending station receives a sequence of DLE ACK and IDs from the receiving station, it sends a transmission block containing the data texts as shown below.
147 Appendices ■ Phase 2 with suspension of data reception for erasure of the flash memory If the receiving BHT-7000 requires the flash memory to be erased for receiving downloaded files, it sends a sequence of WACK and IDs to the sending station to suspend the data transmission.
148 ■ Phase 2 with a sequence of DLE NAK and IDs If the sending station receives a sequence of DLE NAK and IDs from the receiving station in response to a transmission block containing text data m, it sends that transmission block again immediately as shown below.
149 Appendices ■ Phase 2 with a sequence of DLE EOT and IDs If the sending station receives a sequence of DLE EOT and IDs anytime during phase 2, it shifts to phase 3 to terminate the message transmission abnormally. Even if the phase 3 terminates normally, the transmission results in an abnormal end.
150 ■ Abnormal termination of phase 2 (Abort of phase 2) If the sending station receives no sequence of DLE ACK and IDs from the receiving station after sending a sequence of DLE ENQ and IDs 59 times in succession, it sends a sequence of DLE EOT and IDs to the receiving station after 0.
151 Appendices ■ Phase 3 with iterated transmission of DLE EOT and IDs due to no re- sponse or invalid response If the sending station receives no response or any invalid response from the receiving station in response to the sent sequence of DLE EOT and IDs, it iterates sending of the sequence at 0.
152 ■ Phase 3 with timeout at the receiving station If the receiving station receives no subsequent text or normal sequence of DLE EOT and IDs within 30 seconds after sending a sequence of DLE ACK and IDs, it sends a sequence of DLE EOT and IDs and aborts the transmission abnormally.
153 Appendices [ 3 ] CRC To check whether data has been transmitted accurately, the BHT-Ir protocol supports CRC (Cyclic Redundancy Check) which employs the CRC-16 generating system. In CRC, a CRC character is suffixed to a sequence of DLE ETX of every transmission block.
154 Appendix C. A T ypical Basic Operation What follows is a typical basic operation which helps you instruct the hands-on user in practical bar-code reading operation. Application type: Inventory Operation: Power ON → Read the bar code on stock (A).
Index 155 Index Symbols 26-key pad 4, 15, 17, 25, 33, 37, 38, 39, 40, 44, 47, 48, 50, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 68, 69, 72, 73, 75, 76, 80, 81, 126 3-pole mini stereo plug 9, 40, 69, 86 .
156 download 7, 8, 9, 11, 12, 32, 34, 36, 39, 40, 41, 42, 43, 44, 57, 58, 76, 77, 81, 82, 109, 110, 111, 112, 119, 141, 147, 152 driver iv , 11 dry battery cartridge viii, 15, 18, 19, 20, 104, 105, 10.
Index 157 M4 2, 15, 59, 60, 72, 154 magic key v , 34, 47, 59, 60, 126 marker 2, 50, 51, 92 memory size 35 memory test 35, 64 message version 30, 34, 35, 47, 48, 74 N Nonlock 59 O Onetime 59 optical co.
158 U UPC-A 63, 128 UPC-E 63, 128 upload 7, 12, 22, 34, 36, 40, 44, 45, 46, 57, 58, 68, 76, 78, 79, 81, 82, 83, 84, 110, 113, 119, 141, 152 user area 11, 29, 30, 31, 39, 40, 76, 81, 83, 109 V vertical.
Bar Code Handy T erminal BHT -7000 User's Manual First Edition, May 2000 DENSO WAVE INCORPORATED The purpose of this manual is to provide accurate information in the handling and operating of the BHT-7000.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Denso BHT-7000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Denso BHT-7000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Denso BHT-7000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Denso BHT-7000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Denso BHT-7000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Denso BHT-7000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Denso BHT-7000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Denso BHT-7000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
