Manuel d'utilisation / d'entretien du produit P41G002 du fabricant Dell
Aller à la page of 45
Dell Vostro 5480 Owner's Manual Regulatory Model: P41G Regulatory Type: P41G002.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents 1 Working on Your Computer................................................................................ 5 Before Working Inside Your Computer ................................................................................................ 5 Turning Off Your Computer .
Navigation Keys ................................................................................................................................... 33 Updating the BIOS ..................................................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
3. If the computer is connected to a docking device (docked), undock it. CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 4. Disconnect all network cables from the computer.
After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may req.
1. camera-status light 2. camera 3. microphone 4. power-status light 5. battery-status light 6. hard-drive activity light 7. power button 8. HDMI connector 9. USB 3.0 connector 10. network connector 11. headset connector 12. fingerprint reader 13. microphones 14.
3. Pry the base cover along the edges to loosen it. 10.
4. Lift and remove the base cover from the computer. 11.
Installing the Base Cover 1. Place the base cover to align with the screw holes on the computer. 2. Tighten the screws to secure the base cover to the computer. 3. Follow the procedures in After Working Inside Your computer . Removing the Battery 1. Follow the procedures in Before Working Inside Your Computer .
4. Release the tabs that secure the battery in the battery bay. 5. Lift and remove the battery from the computer. 13.
Installing the Battery 1. Place the battery into its slot on the computer. 2. Connect the battery cable to its connector on the system board. 3. Install the base cover . 4. Follow the procedures in After Working Inside Your computer . Removing the Hard Disk Drive 1.
4. Remove the screws that secure the hard drive to the hard drive assembly. a. Lift and remove the hard drive from the hard drive assembly. Installing the Hard Drive 1. Place the hard drive assembly into its slot on the computer. 2. Tighten the screw that secures the hard drive to the computer 3.
Installing the Coin-Cell Battery 1. Place the coin-cell battery into its slot on the computer. 2. Route the coin-cell battery cable along the routing channel. 3. Connect the coin-cell battery cable to its connector on the system board. 4. Install : a.
Removing the System Fan 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. base cover b. battery 3. Perform the steps as shown in the illustration: a. Disconnect the left system fan cable from its connector on the system board.
5. Disconnect the right system fan cable from its connector on the system board. Peel away the system board flex cable from the right system fan. 6. Remove the screws that secure the right system fan to the system board.
7. Lift and remove the right system fan from the computer. 19.
Installing the System Fan 1. Place the right system fan into its original position in the system board and affix the system board flex cable. 2. Tighten the screws that secure the right system fan to the system board. 3. Connect the right system fan cable to its connector on the system board.
Installing the Heatsink 1. Place the heatsink into its original position on the system board. 2. Tighten the screws to secure the heatsink to the system board. 3. Install: a. system fan b. battery c. base cover 4. Follow the procedures in After Working Inside Your computer Removing the Memory Module 1.
Installing the Memory 1. Insert the memory module into the memory socket. 2. Press the memory module down until it clicks into place. 3. Install: a. heatsink b. system fan c. battery d. base cover 4. Follow the procedures in After Working Inside Your computer .
4. Remove the screws that secure the system board to the chassis. 5. Remove the system board from the computer. 23.
Installing the System Board 1. Place the system board into its original position on the chassis. 2. Install the screws that secure the system board to the chassis. 3. Connect : a. camera cable b. touchpad cable c. keyboard cable d. display cable e. speaker cable 4.
3. Disconnect the LVDS cable and the camera cable from its connectors on the system board. 4. Remove the screws that secure the display hinges to the system board. Lift and move the system base panel away from the display hinges to facilitate easy removal of the display assembly.
5. Detach the base panel from the display assembly.. 26.
Installing the Display Assembly 1. Align the base panel of the computer to the display hinges. 2. Install the screws that secure the display hinges to the base panel 3. Connect the LVDS cable and the camera cable to the connectors on the system board.
4. Pry on the plastic caps that cover the display bezel screws and remove them. 5. Remove the screws that secure the display bezel. 28.
6. Pry along the inner edges of the display bezel and remove it. 29.
Installing the Display Bezel 1. Align the display bezel by pressing along the edges. 2. Install the screws that secure the display bezel. 3. Install the plastic caps that secure the display bezel screws on both sides of the display bezel. 4. Install : a.
Installing the Display Panel 1. Align the display panel to the display assembly by pressing along the edges. 2. Install the screws that secure the display panel. 3. Install: a. battery b. base cover c. display assembly d. display bezel 4. Follow the procedures in After Working Inside Your computer .
Installing the Camera 1. Align the camera to the display panel . 2. Connect the camera cable to the camera. 3. Install : a. battery b. base cover c. display assembly d.
3 System Setup System Setup Overview System Setup allows you to: • change the system configuration information after you add, change, or remove any hardware in your computer. • set or change a user-selectable option such as the user password. • read the current amount of memory or set the type of hard drive installed.
NOTE: For most of the system setup options, changes that you make are recorded but do not take effect until you re-start the system. Table 1. Navigation Keys Keys Navigation Up arrow Moves to the previous field.
Follow the instructions on the screen. System Setup Options Main Table 2. Main System Time Re-sets the time on the computer's internal clock. System Date Re-sets the date on the computer's internal calendar. BIOS Version Displays the BIOS revision.
SATA Operation Change the SATA controller mode to either ATA or AHCI. Default: AHCI Adapter Warnings Enable or disable the Adapter Warnings. Default: Enable Function Key Behavior Specifies the behavior of the function key <Fn>. Default: Function key Battery Health Displays a message about the battery health.
4 Troubleshooting Enhanced Pre-Boot System Assessment (ePSA) Diagnostics The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.
Battery Charge LED Off/Hibernate Standby Battery mode Discharging when Battery charge is > 10% Off Off Discharging when Battery charge is <=10% Off Blinking White Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode.
Code Cause and Troubleshooting Steps 7 CPU - cache test failure Processor failure 8 Display Display failure 39.
5 Specifications Technical Specification NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help and Support , and then select the option to view information about your computer.
Feature Description Internal microphone supports Digital microphone x 2 Speakers 3 Volume controls Program menus and keyboard shortcut keys Table 11. Video Feature Description Video type UMA/DIS Video Controller: UMA Intel HD graphics 5x00 Discrete Nvidia N15S-GM Data bus 64–bit External display support HDMI Table 12.
Table 15. Display Feature Description Type HD Dimensions: Height 206.44 mm (8.12 inches) Width 326.18 mm (12.84 inches) Diagonal 14.0" Active area (X/Y) 309.
Feature Description Weight 269 grams (0.60 lb) Charge time 3 hour Voltage 11.4 V Temperature range: Operating 0 ℃ to 50 ℃ Non-Operating 0 ℃ to 65 ℃ Coin-cell battery LI 3V 83 MAH Table 19. AC Adapter Feature Description Type AC adapter Input voltage 90 ~ 264 VAC Input current (maximum) 1.
Feature Description Operating 20% – 90% Storage 20% – 95% Altitude (maximum): Operating –15.2 m to 3048 m (–50 to 10,000 ft) 0° to 35°C Non-Operating –15.2 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G2 or lower as defined by ISA - S71.
6 Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dell P41G002 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dell P41G002 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dell P41G002, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dell P41G002 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dell P41G002, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dell P41G002.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dell P41G002. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dell P41G002 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
