Manuel d'utilisation / d'entretien du produit 3560 du fabricant Dell
Aller à la page of 71
Dell Vostro 3560 Owner's Manual Regulatory Model: P24F Regulatory Type: P24F001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents Notes, Cautions, and Warnings ...................................................................................................2 1 Working on Your Computer ....................................................................................
Removing the Processor ......................................................................................................................................... 34 Installing the Processor ..............................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
6. Close the display and turn the computer upside-down on a flat work surface. NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9.
After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer.
8.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Removing the Security Digital (SD) Card 1. Follow the procedures in Before Working Inside Your Computer . 2.
Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing the ExpressCard 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the battery.
4. Slide the cover outwards to release it from the notches on the computer. 5. Lift the cover upwards and away from the computer. 11.
Installing the Base Cover 1. Align the edge of the base cover on the computer and slide it on the computer. 2. Tighten the screw(s) to secure the base cover to the computer. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer.
4. Use a flat-headed screw driver to pry the optical drive out of the computer. 5. Slide the optical drive outwards and remove it from the computer. 6. Remove the screws that secure the optical-drive bracket. Remove the optical-drive bracket from the optical drive.
Installing the Optical Drive 1. Replace the optical-drive bracket and tighten the screws that secure the optical drive to the optical-drive bracket. 2. Slide the optical drive into the compartment on the chassis. 3. Tighten the screw to secure the optical drive to the computer.
5. Lift up the hard drive and remove from the computer. 6. Remove the screws that secure the hard-drive bracket to the hard drive. 7. Lift up and remove the hard drive from the hard drive bracket.
Installing the Hard Drive 1. Place the hard drive module into the hard drive bracket. 2. Tighten the screws that secures the hard drive bracket to the hard drive. 3. Pull the tab and place the hard drive on the chassis. 4. Tighten the screws that secure hard drive to the computer.
5. Lift the clip to release the keyboard cable and disconnect it from the system board. 6. Lift the clip to release the backlit cable and disconnect it from the system board.
Installing the Keyboard 1. Connect the keyboard data cable to the back of the keyboard. 2. Connect the backlit cable to the system board. 3. Insert the keyboard in its compartment. 4. Press down until the keyboard clicks into place. 5. Install the battery.
4. Push to release the hinge cover from the computer. 5. Flip the computer and carefully remove the display hinge cover from the computer. Installing the Display Hinge Cover 1. Replace the display hinge cover back to the computer till the latches are fixed into place.
f) keyboard g) display hinge cover 3. Remove the rubber pads from the bottom of the computer. 4. Remove the screws from the bottom of the computer. 5. Disconnect the LEDs fingerprint cable.
6. Remove the screws that secures palmrest assembly in place. 7. Lift the latch and disconnect the power button fingerprint cable. 21.
8. Lift the tab and release the touchpad cable, SD card reader cable, and fingerprint scanner cable from the computer. 9. Lift the tab and disconnect the functions button cable from the system.
10. Carefully pry up the palmrest along the edges. 11. Slide the palmrest outwards and lift to remove from the computer. 23.
Installing the Palmrest 1. Starting from the edges of the palmrest, press downwards on the palmrest to engage the tabs on the computer. 2. Tighten the screws to secure the palmrest to the front of the computer. 3. Connect the functions button cable to the system board.
f) display hinge cover g) palmrest 3. Lift the tab and disconnect the express card reader cable. 4. Remove the screws that secure the express card reader in place.
Installing the Express Card Reader 1. Place the express card reader into its slot on the chassis. 2. Tighten the screws to secure the express card reader to the computer. 3. Connect the express card reader cable. 4. Install the: a) palmrest b) display hinge cover c) keyboard d) base cover e) battery f) express card g) SD card 5.
4. Remove the screws that secure the speakers in place. 5. Lift up the left speaker and remove. 27.
Installing the Speakers 1. Place the speakers on the computer and thread the speakers cable through the routing tabs. 2. Tighten the screws to secure the speakers in place.
j) SD card reader 3. Disconnect the system fan cable and the power cable. 4. Disconnect the speaker cable. 5. Disconnect the Express card reader fingerprint cable.
7. Peel off the tape and disconnect the LVDS and camera cable. 8. Remove the screws that secure the system board to the chassis. 30.
9. Lift up the system board from the chassis. 10. Slide the system board towards right and remove from the chassis. 31.
Installing the System Board 1. Align the system board to the port connectors and place the system board in the computer. 2. Tighten the screws to secure the system board to the chassis. 3. Affix the tape and connect the LVDS and camera cable. 4. Connect the touchpad cable.
e) memory f) optical drive g) hard disk drive h) keyboard i) display hinge cover j) palmrest k) system board 3. Disconnect the system fan cable from the system board. 4. Remove the screws that secure the heat sink to the system board. 5. Lift up and remove the heat sink from the system board.
Installing the Heat Sink 1. Tighten the screws to secure the heat sink to the system board. 2. Connect the system fan cable to the system board. 3. Install the: a) system board b) palmrest c) display hinge cover d) keyboard e) hard drive f) optical drive g) memory h) base cover i) battery j) express card k) SD card 4.
j) speaker k) system board l) heat sink 3. Remove the screw. Remove the processor cover and lift the processor from the socket. Place it in an antistatic package. Installing the Processor 1. Insert the processor into the processor socket. Ensure the processor is properly seated.
4. Use a screw driver to release the coin-cell battery from the socket. The battery pops-out, lift and remove the battery from the socket. Installing the Coin-Cell Battery 1. Insert the coin-cell battery into the slot. 2. Press on the coin-cell battery until it secures into place.
4. Install the: a) palmrest b) keyboard c) base cover d) battery 5. Follow the procedures in After Working Inside Your Computer . Removing the LAN Board 1.
5. Pull out and remove the LAN board from the system. Installing the LAN Board 1. Insert the LAN board into its compartment and align on to the chassis.
j) express card k) SD Card 4. Follow the procedures in After Working Inside Your Computer. Removing the mini-SATA Card 1. Follow the procedures in Before Working Inside Your Computer.
Removing the Secure Digital (SD) Card Reader 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD card b) express card c) battery d) base cover e) optical drive f) hard drive g) keyboard h) display hinge cover i) palmrest 3.
5. Lift up and remove the SD card reader from the system. Installing the Secure Digital (SD) Card Reader 1. Place the SD card reader into the place. 2.
k) express card reader l) system board m) WLAN card n) LAN board 3. Remove the screws from the base of the system. 4. Remove the screws present below the display hinge cover. 5. Remove the left screw that secure the display assembly in place. 6. Unthread the camera cable and remove the right screw that secure the display assembly to the system.
7. Lift the display assembly up from the system and remove. Installing the Display Assembly 1. Align the display assembly to the computer base. 2. Thread the camera cable and tighten the screw to secure the right hinge in place. 3. Tighten the screw that secure the left hinge in place.
f) display hinge cover g) keyboard h) hard drive i) optical drive j) memory k) base cover l) battery m) express card n) SD card 7. Follow the procedures in After Working Inside Your Computer . Removing the Power Connector 1. Follow the procedures in Before Working Inside Your Computer.
j) battery k) express card l) SD card 3. Follow the procedures in After Working Inside Your Computer . Removing the Display Bezel 1. Follow the procedures in Before Working Inside Your Computer 2.
4. Lift up the display bezel and remove from the display assembly. Installing the Display Bezel 1. Align the display bezel with the display assembly and gently snap it into place.
j) optical drive k) memory l) base cover m) battery n) express card o) SD card 3. Follow the procedures in After Working Inside Your Computer . Removing the Display Bracket 1.
4. Lift up and remove the display panel with brackets and hinges. 5. Peel off the tape and disconnect the display cable. 48.
6. Remove the screws that secure the display brackets and hinges to the display panel. Installing the Display Bracket 1. Tighten the screws to secure the display brackets and hinges to the display panel. 2. Affix the tape and connect the display cable.
g) palmrest h) display hinge cover i) keyboard j) hard drive k) optical drive l) base cover m) battery n) express card o) SD card 6. Follow the procedures in After Working Inside Your Computer . Removing the Camera Module 1. Follow the procedures in Before Working Inside Your Computer .
h) palmrest i) hard drive j) optical drive k) keyboard l) display hinge cover m) base cover n) battery o) express card p) SD card 4. Follow the procedures in After Working Inside Your Computer .
52.
3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only.
Main L2 Cache Displays the processor L2 cache size. L3 Cache Displays the processor L3 cache size. Fixed HDD Displays the model number and capacity of the hard drive. SATA ODD Displays the model number and capacity of the optical drive. mSata Device Displays the model number and capacity of the mini- Sata device.
Advanced SATA Operation Change the SATA controller mode to either ATA or AHCI. Default: AHCI Adapter Warnings Enables or disables adapter warnings. Default: Enabled Function Key Behavior Specifies the behavior of the function key <Fn> .
Table 4. Security Options Security Set Service Tag This field displays your system's service tag. If the service tag is not already set, this field can be used to enter it.
Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For notebooks, ensure that your computer battery is fully charged and connected to a power outlet 1. Restart the computer.
NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you need not provide the system password to log on to the computer. To enter a system setup, press <F2> immediately after a power-on or reboot.
60.
4 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss.
Turns on steadily or blinks to indicate battery charge status. Turns on when wireless networking is enabled. Battery Status Lights If the computer is connected to an electrical outlet, the battery lig.
Beep Description Possible Cause/Troubleshooting Steps • reseat the memory if an additional memory is available • install that memory if the issue persists • issue with the memory connector 5 Real-time clock power fail CMOS battery failure. Reseat the battery.
64.
5 Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help and Support , and then select the option to view information about your computer.
Feature Description Vostro 3460 / Vostro 3560 Conexant CX20672-21Z Stereo conversion 24-bit (analog-to-digital and digital-to-analog) Interface: Internal high definition audio External microphone-in/stereo headphones/external speakers connector Speakers 2 W Volume controls keyboard function keys and program menus Table 12.
Feature Description • Bluetooth • WWAN (optional) Table 15. Ports and Connectors Feature Description Audio: Vostro 3360 one stereo headphone/headset/audio-out connector Vostro 3460 / 3560 one microphone connector, one headphone connector Video • one 15-pin VGA connector • one 19-pin HDMI connector Network adapter one RJ-45 connector USB 3.
Feature Description Maximum Brightness 200 nits Operating angle 0° (closed) to 140° Refresh rate 60 Hz Minimum Viewing angles: Horizontal 40°/40° Vertical 15°/30° (H/L) Pixel pitch 0.
Feature Description Vostro 3360 14.8 VDC Vostro 3460 / Vostro 3560 11.1 VDC Temperature range: Operating 0 °C to 35 °C (32 °F to 95 °F) Non-Operating –40 °C to 65 °C (–40 °F to 149 °F) Coin-cell battery 3 V CR2032 lithium coin cell Table 20.
Table 21. Physical Feature Description Vostro 3360 Vostro 3460 Vostro 3560 Height 19.20 mm (0.75 inch) 30.10 mm (1.18 inches) 32.50 mm (1.27 inches) Width 332.00 mm (13.07 inches) 345.50 mm (13.60 inches) 375.00 mm (14.76 inches) Depth 232.50 mm (9.15 inches) 244.
6 Getting Help Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dell 3560 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dell 3560 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dell 3560, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dell 3560 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dell 3560, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dell 3560.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dell 3560. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dell 3560 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
