Manuel d'utilisation / d'entretien du produit 3460 du fabricant Dell
Aller à la page of 61
Dell Vostro 3460 Owner's Manual Regulatory Model: P34G Regulatory Type: P34G001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents Notes, Cautions, and Warnings ...................................................................................................2 1 Working on Your Computer ....................................................................................
Removing the Camera ............................................................................................................................................. 30 Installing the Camera ................................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
6. Close the display and turn the computer upside-down on a flat work surface. NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9.
CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 3. Replace the battery. 4. Connect your computer and all attached devices to their electrical outlets.
8.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may req.
3. Lift and remove the battery from the computer. Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing the Base Cover 1. Follow the procedures in Before Working Inside Your Computer .
4. Slide the cover outwards to release it from the notches on the computer. 5. Lift the cover upwards and away from the computer. 11.
Installing the Base Cover 1. Align the edge of the base cover on the computer and slide it on the computer. 2. Tighten the screw(s) to secure the base cover to the computer. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer.
Removing the Optical Drive 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) battery b) base cover 3. Remove the screw that secures the optical drive to the computer. 4. Use a flat-headed screw driver to pry the optical drive out of the computer.
6. Remove the screws that secure the optical-drive bracket. Remove the optical-drive bracket from the optical drive. Installing the Optical Drive 1. Replace the optical-drive bracket and tighten the screws that secure the optical drive to the optical-drive bracket.
4. Lift the tab to disconnect the hard-drive cable from the system board. Lift the hard drive to loosen it from the chassis. 5. Slide and remove the hard drive from the computer.
6. Disconnect the hard-drive cable. Remove the screws securing the hard drive to hard-drive bracket. Lift the hard drive from the bracket. Installing the Hard Drive 1. Place the hard drive into the hard-drive bracket. 2. Tighten the screws that secures the hard-drive bracket to the hard drive.
4. Lift and flip the keyboard from the computer. 5. Release the latch on the system board connector, then disconnect the mylar tape from the connector.
Installing the Keyboard 1. Connect the keyboard data cable to the system board. 2. Connect the mylar tape to the system board. 3. Insert the keyboard in its compartment. 4. Press down until the keyboard clicks into place. 5. Install the battery. 6. Follow the procedures in After Working Inside Your Computer .
4. Turn the computer over towards the front. Release the latch and disconnect the power-button cable. 5. Release the latch and disconnect fingerprint and touchpad cables.
6. Release the latch and disconnect the hotkey cable. 7. Loosen the screw and disconnect the LVDS cable from the system board. 20.
8. Unthread and remove the LVDS cable. 9. Remove the screws from the front of the computer. 21.
10. Use a screwdriver and pry the palmrest towards the display. 11. Slide the palmrest outwards and lift to remove from the computer. 22.
Installing the Palmrest 1. Align the palmrest on its position on the computer. 2. Starting from the edges of the palmrest, press downwards to engage the tabs on the computer. 3. Tighten the screws to secure the palmrest to the computer. 4. Thread the LVDS cable along the notches on the palmrest.
Installing the Wireless Local Area Network (WLAN) Card 1. Slide the WLAN card into its slot. 2. Connect the antenna cables according to the color code on the WLAN card. 3. Tighten the screw to secure the WLAN card. 4. Install the: a) palmrest b) keyboard c) base cover d) battery 5.
Installing the Display Assembly 1. Align the display assembly to its location on the computer base. 2. Tighten the screws to secure the display assembly to the chassis. 3. Install the: a) palmrest b) keyboard c) battery 4. Follow the procedures in After Working Inside Your Computer .
4. Pry and remove the display-hinge cover from the computer. Installing the Display-Hinge Cover 1. Press the display-hinge cover till it clicks into place.
4. Follow the procedures in After Working Inside Your Computer . Removing the Display Bezel 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) battery b) keyboard c) palmrest d) display-hinge cover e) display assembly 3.
e) display assembly 3. Remove the screws that secure the display to the display assembly. 4. Lift the display away from the display assembly. 5. Peel the sticker to remove the display from the display assembly.
Installing the Display 1. Affix the sticker to the display connecting it to the display assembly. 2. Place the display to its original position on the display assembly. 3. Tighten the screws to secure the display to the display assembly. 4. Install the: a) display assembly b) display-hinge cover c) palmrest d) keyboard e) battery 5.
Installing the Power Connector 1. Place the power connector in its location on the base of the chassis. 2. Tighten the screw to secure the power connector. 3. Install the: a) display-hinge cover b) display assembly c) system board d) WLAN card e) palmrest f) keyboard g) base cover h) battery 4.
3. Install the: a) display bezel b) display assembly c) palmrest d) keyboard e) battery 4. Follow the procedures in After Working Inside Your Computer .
Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) battery b) base cover c) memory d) optical drive e) hard drive f) keyboard g) palmrest h) heat-sink fan i) WLAN 3. Disconnect the power cable from the system board.
6. Lift the system board upwards. 7. Slide the system board and lift it from the chassis. 33.
Installing the System Board 1. Align the system board to the port connectors and place the system board in the computer. 2. Tighten the screws to secure the system board to the chassis. 3. Connect the speaker cable to the system board. 4. Connect the power-connector cable to the system board.
j) heat sink-fan k) system board 3. Flip the system board and locate the coin-cell battery. 4. Use a screw driver to release the coin-cell battery from the socket. The battery pops-out, lift and remove the battery from the socket. Installing the Coin-Cell Battery 1.
4. Lift and remove the heat sink from the system board. Installing the Heat Sink 1. Place the thermal module on the system board. 2. Tighten the screws to secure the heat sink to the system board. 3. Install the: a) system board b) heat-sink fan c) palmrest d) keyboard e) hard drive f) optical drive g) base cover h) battery 4.
c) memory d) optical drive e) hard drive f) keyboard g) palmrest h) WLAN card i) heat-sink fan j) system board NOTE: You do not need to remove the system board to remove the speaker, however you must disconnect the speaker cable from the system board.
a) battery b) base cover c) memory d) optical drive e) hard drive f) keyboard g) palmrest h) WLAN card i) ExpressCard reader(if available) j) heat sink-fan k) system board l) heat sink 3. Remove the screw. Remove the processor cover and lift the processor from the socket.
e) hard drive f) keyboard g) palmrest h) WLAN card 3. Remove the screw that secures the mini-SATA card to the system board. Slide the card from its connector on the system board. Installing the mini-SATA Card 1. Place the card into the mini-SATA slot.
4. Remove the screws that secure the daughter board to the system board. 5. Lift and remove the system board to access the daughter board. 40.
Installing the USB Daughter Board 1. Place the daughter board on the system board and tighten the screw to secure it. 2. Install the: a) processor b) heat sink c) coin-cell battery d) mini-SATA e) system board f) WLAN card g) palmrest h) keyboard i) hard drive j) optical drive k) memory l) base cover m) battery 3.
42.
3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only.
Main L2 Cache Displays the processor L2 cache size. L3 Cache Displays the processor L3 cache size. Fixed HDD Displays the model number and capacity of the hard drive. SATA ODD Displays the model number and capacity of the optical drive. mSata Device Displays the model number and capacity of the mini- Sata device.
Advanced SATA Operation Change the SATA controller mode to either ATA or AHCI. Default: AHCI Adapter Warnings Enables or disables adapter warnings. Default: Enabled Function Key Behavior Specifies the behavior of the function key <Fn> .
Table 4. Security Options Security Set Service Tag This field displays your system's service tag. If the service tag is not already set, this field can be used to enter it.
Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For notebooks, ensure that your computer battery is fully charged and connected to a power outlet 1. Restart the computer.
NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you need not provide the system password to log on to the computer. To enter a system setup, press <F2> immediately after a power-on or reboot.
50.
4 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss.
52.
5 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Device Status Lights Table 6. Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode.
Table 7. Diagnostic Beep Codes Beep Description Possible Cause/Troubleshooting Steps 1 BIOS ROM checksum in progress of failure. System board failure, covers BIOS corruption or ROM error 2 No RAM dete.
6 Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help and Support , and then select the option to view information about your computer.
Feature Description Vostro 3460 / Vostro 3560 Conexant CX20672-21Z Stereo conversion 24-bit (analog-to-digital and digital-to-analog) Interface: Internal high definition audio External microphone-in/stereo headphones/external speakers connector Speakers 2 W Volume controls keyboard function keys and program menus Table 12.
Feature Description • Bluetooth • WWAN (optional) Table 15. Ports and Connectors Feature Description Audio: Vostro 3360 one stereo headphone/headset/audio-out connector Vostro 3460 / 3560 one microphone connector, one headphone connector Video • one 15-pin VGA connector • one 19-pin HDMI connector Network adapter one RJ-45 connector USB 3.
Feature Description Maximum Brightness 200 nits Operating angle 0° (closed) to 140° Refresh rate 60 Hz Minimum Viewing angles: Horizontal 40°/40° Vertical 15°/30° (H/L) Pixel pitch 0.
Feature Description Vostro 3360 14.8 VDC Vostro 3460 / Vostro 3560 11.1 VDC Temperature range: Operating 0 °C to 35 °C (32 °F to 95 °F) Non-Operating –40 °C to 65 °C (–40 °F to 149 °F) Coin-cell battery 3 V CR2032 lithium coin cell Table 20.
Table 21. Physical Feature Description Vostro 3360 Vostro 3460 Vostro 3560 Height 19.20 mm (0.75 inch) 30.10 mm (1.18 inches) 32.50 mm (1.27 inches) Width 332.00 mm (13.07 inches) 345.50 mm (13.60 inches) 375.00 mm (14.76 inches) Depth 232.50 mm (9.15 inches) 244.
7 Contacting Dell To contact Dell for sales, technical support, or customer service issues: 1. Visit support.dell.com. 2. Verify your country or region in the Choose a Country/Region drop-down menu at the bottom of the page. 3. Click Contact Us on the left side of the page.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dell 3460 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dell 3460 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dell 3460, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dell 3460 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dell 3460, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dell 3460.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dell 3460. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dell 3460 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
