Manuel d'utilisation / d'entretien du produit 3010 du fabricant Dell
Aller à la page of 61
Dell OptiPlex 3010 Mini-Tower Owner's Manual Regulatory Model: D12M Regulatory Type: D12M001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents 1 Working on Your Computer....................................................................................................... 7 Before Working Inside Your Computer ..........................................................................
3 System Setup............................................................................................................................. 31 System Setup ...............................................................................................
Memory write/read failure at address, read value expecting value ................................................................ 52 Memory size in CMOS invalid ..........................................................................................
6.
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Removing the Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Pull up the cover-release-latch at the side of the computer.
Removing the Front Bezel 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the cover . 3. Pry the front bezel retention clips away from the chassis located at the side edge of front bezel. 4. Rotate the bezel away from the computer to release the hooks on the opposite edge of the bezel from the chassis.
4. Pull the release lever away from the PCIe x16 card to release the securing tab from the dent in the card. Then, ease the card up and out of its connector and remove it from the computer. 5. Lift the PCIe x1 expansion card (if any) up and out of its connector and remove it from the computer.
Related Links Installing the Expansion Card Installing The Expansion Card 1. Insert the PCIe x4 card into the connector on the system board and press down to secure it in place. 2. Insert the PCIe card (if any) into the connector on the system board and press down to secure it in place.
6. Repeat steps 4 and 5 to remove the second optical drive (if available). Related Links Installing the Optical Drive Installing The Optical Drive 1. Slide up the optical-drive latch and push the optical drive from the front towards the back of the computer.
5. Flex the hard-drive bracket and then remove the hard drive from the bracket. 6. Repeat the above steps for the second hard drive, if available. Related Links Installing the Hard Drive Installing The Hard Drive 1. Flex the hard-drive bracket and then insert the hard drive into the bracket.
4. Lift the memory modules out of the connectors on the system board. Related Links Installing the Memory Installing the Memory 1. Insert the memory modules into the connectors on the system board. Install the memory module in the order of A1 > B1 > A2 > B2.
4. Slide the intrusion switch toward the chassis bottom and remove it from the system board. Related Links Installing the Intrusion Switch Installing the Intrusion Switch 1. Insert the intrusion switch into the chassis rear and slide it toward the chassis top to secure it.
4. Unthread the speaker cable from the chassis clip. 5. Press down the speaker-securing tab and slide the speaker upwards to remove it. Related Links Installing the Internal Speaker Installing the Speaker 1. Press the speaker-securing tab and slide the speaker downward to secure it.
Removing the Heat Sink and Processor 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the cover . 3. Disconnect the heat sink assembly cable from the system board. 4. Loosen the captive screws that secure the heat sink assembly to the system board.
7. Lift the processor cover. 8. Lift the processor to remove it from the socket and place it in an antistatic package. Related Links Installing the Heat Sink and Processor Installing the Heat Sink and Processor 1. Insert the processor into the processor socket.
Removing the Heat Sink and Processor Removing The Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the cover . 3. Press the release latch away from the coin-cell battery to allow the battery to pop-up from the socket.
5. Disconnect the power-switch cable from the system board. 6. Unthread the power-switch cable from the chassis clips. 7. Unthread the power-switch cable from the chassis clip. 8. Pry the power-switch cable free. 9. Slide the power-switch cable out through the front of the computer.
Related Links Installing the Power Switch Cable Installing the Power-Switch Cable 1. Slide the power-switch cable in through the front of the computer. 2. Secure the power-switch cable to the chassis. 3. Thread the power-switch cable into the chassis clips.
5. Pry the thermal sensor away from the chassis front and remove. Related Links Installing the Front Thermal Sensor Installing the Front Thermal Sensor 1. Secure the thermal sensor to the chassis front. 2. Thread the thermal sensor cable into the chassis clips.
4. Pry and remove the system fan away from the four grommets securing it to the back of the computer. Installing the System Fan 1. Place the system fan in the chassis. 2. Pass the four grommets through the chassis and slide outward along the grooves to secure them in place.
6. Remove the screw that secures the Input/Output panel to the computer. 7. Slide the Input/Output panel towards the left of the computer to release it.
Installing the Input/Output Panel 1. Insert the Input/Output panel into the slot on the chassis front. 2. Slide the Input/Output panel towards the right of the computer to secure to the chassis. 3. Tighten the single screw to secure the Input/Output panel to the chassis.
6. Disconnect the 4-pin power cable from the system board. 7. Remove the screws that secure the power supply to the back of the computer. 8. Push in on the blue release tab beside the power supply, and slide the power supply towards the front of the computer.
Related Links Installing the Power Supply Installing the Power Supply 1. Place the power supply in the chassis and slide towards the back of the computer to secure it. 2. Tighten the screws securing the power supply to the back of the computer. 3. Connect the 4-pin power cable to the system board.
8. Slide the system board towards the front of the computer. 9. Carefully tilt the system board to 45 degrees, and then lift the system board out of the computer. Installing The System Board 1. Align the system board to the port connectors on the back of the chassis and place the system board in the chassis.
30.
3 System Setup System Setup This computer offers you the following options: • Access System Setup by pressing <F2> • Bring up a one-time boot menu by pressing <F12> Press <F2> to enter System Setup and make changes to the user-definable settings.
Since the one-time boot menu only affects the current boot, it has the added benefit of not requiring the technician to restore the customer's boot order after completing troubleshooting. Timing Key Sequences The keyboard is not the first device initialized by Setup.
Action Keystroke Exit BIOS <Esc> — Remain in Setup, Save/Exit, Discard/Exit Change a setting Left or right-arrow key Select field to change <Enter> Cancel modification <Esc> Reset .
Option Description NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not appear. Serial Port Allows you to set the serial port settings.
Option Description Strong Password This option lets you enable or disable strong passwords for the system. Password Configuration Allows you to control the minimum and maximum number of characters allowed for a administrative password and the system password.
Table 4. Secure Boot Option Description Secure Boot Enable Allows you to enable or disable Secure Boot feature • Disable • Enable Expert key Management Allows you to manipulate the security key databases only if the system is in Custom Mode. The Enable Custom Mode option is disabled by default.
Option Description • Last State This option is Power Off by default. Auto On Time Sets time to automatically turn on the computer. Time is kept in standard 12-hour format (hour:minutes:seconds). Change the startup time by typing the values in the time and AM/PM fields.
Option Description This option is set to Thorough by default. Table 8. Virtualization Support Option Description Virtualization This option specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel ® Virtualization Technology.
Option Description NOTE: This field is only relevant when the "Integrated NIC" control in the "System Configuration" group is set to "Enabled with ImageServer". Client IP Specifies the static IP address of the client. The default IP address is 255.
40.
4 Troubleshooting Diagnostic LEDs NOTE: The diagnostic LEDs only serve as an indicator of the progress through the Power-on Self-Test (POST) process. These LEDs do not indicate the problem that caused the POST routine to stop. The diagnostic LEDs are located on the front of the chassis next to the power button.
Problem Description A possible system board failure has occurred. Troubleshooting Steps Unplug the computer. Allow one minute for the power to drain. Plug the computer into a working electrical outlet and press the power button. LED Power Button Problem Description A possible system board, power supply, or peripheral failure has occurred.
Problem Description BIOS may be corrupt or missing. Troubleshooting Steps The computer hardware is operating normally but the BIOS may be corrupt or missing. LED Power Button Problem Description A possible system board failure has occurred. Troubleshooting Steps Remove all peripheral cards from the PCI and PCI-E slots and re-start the computer.
Problem Description A possible system board failure has occurred. Troubleshooting Steps • Disconnect all internal and external peripherals, and re-start the computer. If the computer boots, add the peripheral cards back one by one until you find the bad one.
Power Button Problem Description A possible hard drive failure has occurred. Troubleshooting Steps Re-seat all power and data cables. LED Power Button Problem Description A possible USB failure has occurred. Troubleshooting Steps Re-install all USB devices and check all cable connections.
LED Power Button Problem Description A possible expansion card failure has occurred. Troubleshooting Steps • Determine if a conflict exists by removing an expansion card (not a graphics card) and restarting the computer. • If the problem persists, reinstall the card you removed, then remove a different card and restart the computer.
• If the operating system is attempting to boot from a device (optical drive), check system setup to ensure the boot sequence is correct for the devices installed on your computer. Beep Codes The computer can emit a series of beeps during start-up if the display cannot show errors or problems.
Code 3-2-2 Cause Interrupt vector loading failure Code 3-2-4 Cause Keyboard Controller Test failure Code 3-3-1 Cause NVRAM power loss Code 3-3-2 Cause NVRAM configuration Code 3-3-4 Cause Video Memory.
Code 4–4–1 Cause Serial or parallel port test failure Code 4–4–2 Cause Failure to decompress code to shadowed memory Code 4–4–3 Cause Math coprocessor test failure Code 4–4–4 Cause Cache test failure Error Messages Address mark not found Description The BIOS found a faulty disk sector or could not find a particular disk sector.
Controller has failed Description The hard drive or the associated controller is defective. Data error Description The floppy or hard drive cannot read the data. For the Windows operating system, run the chkdsk utility to check the file structure of the floppy or hard drive.
Hard-disk drive controller failure Description The hard drive failed initialization. Hard-disk drive failure Description The hard drive failed initialization.
Memory double word logic failure at address, read value expecting value Description A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them. Memory odd/even logic failure at address, read value expecting value Description A memory module may be faulty or improperly seated.
Not a boot diskette Description The operating system is trying to boot to a floppy disk that does not have a bootable operating system installed on it. Insert a bootable floppy disk. Plug and play configuration error Description The computer encountered a problem while trying to configure one or more cards.
Timer chip counter 2 failed Description A chip on the system board may be malfunctioning. Unexpected interrupt in protected mode Description The keyboard controller may be malfunctioning or a memory module may be loose.
5 Specifications Specification NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (or Start in Windows XP) Help and Support, and then select the option to view information about your computer.
Video Video memory: Integrated up to 1.7 GB shared video memory (Microsoft Windows Vista and Windows 7) Discrete up to 1 GB Audio Integrated integrated Conexant CX20641 HD-audio codec Network Integrated integrated Realtek RTL8111E Ethernet capable of 10/100/1000 Mb/s communication Expansion Bus Bus Type PCI Express 2.
Drives Mini-Tower two Desktop one Small Form Factor one External Connectors Audio: Back Panel Mini-Tower/Desktop three connectors once each for line-out, line- in, and microphone Small Form Factor two connectors for line-out and line-in/ microphone Front Panel two connectors for microphone and headphone Network Adapter one RJ45 connector USB 2.
System Board Connectors Mini-Tower, Desktop two 3-pin connector Small Form Factor one 5-pin connector Front panel control one 16-pin, two 10–pin, and one 5-pin connector Processor one 1155-pin conne.
Controls and Lights NOTE: You can test the health of the power system by pressing the test button. When the system power supply voltage is within specification, the self-test LED lights up. If the LED does not light up, the power supply may be defective.
60.
6 Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dell 3010 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dell 3010 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dell 3010, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dell 3010 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dell 3010, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dell 3010.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dell 3010. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dell 3010 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
