Manuel d'utilisation / d'entretien du produit DWF-805 du fabricant Daewoo
Aller à la page of 47
Ser vice Manual Auto Washer Model : DWF -750/752/800/802 753/755/803/805 756/758/806/808 DAEWOO ELECTRONICS CO., L TD. ✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list.
ASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT O WASH T O WASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT O WASHER AUT.
1. SPECIFICA TIONS 2 SPECIFICA TIONS NO. ITEM 1 POWER SOURCE A V AILABLE IN ALL LOCAL AC VOL T AGE 2 POWER 50Hz 320W CONSUMPTION 60Hz 300W(1 10~127V) / 340W(220V) 3 MACHINE NET WEIGHT GROSS 4 DIMENSIO.
2. STRUCTURE OF THE W ASHING MACHINE 3 STRUCTURE • GROUND WIRE In case of 3-wire power cord, ground wire will not be provided • POWER CORD • DRAIN HOSE • LINT FILTER • COLD WATER TAP After u.
3. FUNCTIONS OF THE CONTROL P ANEL 4 CONTROL P ANEL • Press this switch to turn the power on or of f. • It can be used to choose water temperature to be supplied. • As the button is pressed, water temperature will be repeated. COLD → COLD+HOT → HOT • In case of the single valve model, there is no wash temperature selector function.
5 PROCEDURE • Press this switch to turn the power on or of f. • It can be used to choose water temperature to be supplied. • As the button is pressed, water temperature will be repeated. COLD → COLD+HOT → HOT • In case of the single valve model, there is no wash temperature selector function.
6 4. DIRECTIONS FOR INST ALLA TION AND USE DIRECTIONS The opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor . § § Location Of Washer Check location where washer will be installed. Make sure you have everything necessary for correct installation.
7 CONNECTION FOR ORDINAR Y T AP 6 Connect the inlet hose adapter of the hose to the water inlet of the washer by turning it clock- wise to be fixed tightly . • Please check the rubber packing inside the inlet hose adapter of the hose. 1 Pull down the collar of the inlet hose to separate it from the water tap adapter .
8 CONVENIENCE § § How To Clean The Filter 4 Remove the dirt from the inlet filter with a brush. 1 Pull the power plug out before cleaning it. 2 T urn off the water supply to the washer and separate the inlet hose.
9 5. FEA TURE AND TECHNICAL EXPLANA TION EXPLANA TION W ASH DRAIN SPIN FILL RINSE 1 DRAIN SPIN FILL RINSE 2 DRAIN •• • MOTOR C.W SINGAL C.C.W TIME(SEC.) 0.4 0.4 0.4 0.4 0.4 0.4 ••••••• 40 SEC. (About 25 Times) * When the water level is “HIGH” Feature of the Washing Machine 1 The first air bubble washing system in the world.
10 EXPLANA TION FUNCTIONAL PRINCIPLE 1 The micom can remember the time from the begining of drain to reset point when the pressure switch reaches to “OFF” point 2 In case of continuous draining, residual drain time is determined by micom. Draining time as a whole = D + 40 Residual drain time.
11 EXPLANA TION This is the device to dispense the softener automatically by centrifugal force. This is installed inside the auto-balancer. FUNCTIONAL PRINCIPLE 1 Softener stays in room (A) when poured into softener inlet. 2 Softener moves from (A) to (B) by centrifugal force during intermittent spin process.
12 EXPLANA TION Automatic Unbalance Adjustment Circulating-Water The alarm finished when you close the lid after opening it. Check the unbalance of the wash load and the installation condition. NOTES Filter T ub Outer tub W ater channel Pulsator This system is to prevent abnormal vibration during intermittent spin and spin process.
13 EXPLANA TION Much lint may be obtained according to the kind of clothes to be washed and some of the lint may also sticks to the clothes. T o minimize this possibility a lint filter is provided on the upper part of the tub to filter the wash water as it is discharged from the water channel.
14 EXPLANA TION The proper water currents is made by the rotation of pulsator at a low speed to prevent the damage to the small sized clothes. STRUCTURE Pulsator shaft One way clutch bearing Brake lev.
15 EXPLANA TION PRINCIPLE OF INT AKE & OUTLET OF THE AIR INT AKE : ARMA TURE moves up, and BELLOWS inhales the air. At the same time, protector B is open and A is close. OUTLET : ARMA TURE moves down, and BELLOWS exhausts the air. At the same time, protector B is close and A is opend.
16 DIRECTIONS 6. DIRECTIONS FOR DISASSEMBL Y AND ADJUSTMENT ¡ Raise the top plate on the outer cabinet. ¡ Remove outer tub cover from the tub ass’y . ¡ Remove the spinner shaft flange nut by using ‘T’ type box wrench. ¡ Loosen the pulsator mounting screw and remove the pulsator .
17 DIRECTIONS ¡ Lay the front of the washer on the floor. ¡ Remove four bolts mounting the plate-gear protect by using a box wrench and remove plate-gear protect. ¡ Remove the V -belt. ¡ Remove four bolts mounting the gear mechanism ass’y by using a box wrench.
18 DIRECTIONS ¡ Loosen the adjustment bolt and turn the adjust - ment bolt until the end of the bolt touches to the brake lever . ¡ T ighten the lock nut and apply a small amount of paint-lock. Adjustment bolt Clutch lever Gear mechanism ass'y Brake lever NOTES: 1.
19 THE REP AIR 7. THE REP AIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM ¡ ¡ T OOL FOR REPLACING THE CLUTCH BOSS ASSEMBLE ¡ ¡ T ool name Specification Q’ty Fixing jig 1 Ratchet handle 1 .
20 THE REP AIR NO. P ARTS NAME SPECIFICA TION CODE Q’TY 1 CLUTCH SPRING 1.5*1.5 36151 10000 1 2 CLUTCH BOSS PP 3619301300 1 3 GREASE beacon#325 3g P ACKING P ACKING THE CLUTCH BOSS ASS’Y 1 METHOD BY USING VINYL P ACK 1) THE LAUNDARY IS IN THE SPIN TUB UNEVENL Y WHEN JUST ST ARTING SPIN PROCESS.
21 THE REP AIR No. Process Notice Disassemble 1 1 2 3 4 Release screws marked 4-point Remove the protector Remove the v-belt Loosen the fastening nut Disassemble the spring washer Use wrench or driver - ratchet handle - extension bar - socket : 10mm Use fixing jig for pulley as to see fig 1.
22 THE REP AIR No. Process Notice Disassemble 2 5 6 7 8 Disassemble the pulley Disassemble the clutch boss assembly Separate coupling from clutch boss ass’y Cleaning Catch the boss and pull upward w.
23 THE REP AIR No. Process Notice Assemble 1 1 2 3 4 Assemble the coupling Assemble the new clutch boss ass’y Assemble the pulley Assemble the spring washer Check the uneven face of cou- pling is assembled upward - Push in the clutch boss ass’y with rotating on the clockwise direction.
24 THE REP AIR No. Process Notice Assemble 2 5 6 7 8 Clutch T ip Drain V alve Synchronous Motor 3.5~4.5 keep distance 2~3mm Assemble the fastening nut Assemble the Belt Assemble the protector Final checking - Use fixing jig and 17mm socket wrench as if disassembling, as fastening torque about 100~200kgf-cm.
8. TROUBLE SHOOTING GUIDE 25 TROUBLE SHOOTING PROBLEM W A TER IS NOT SUP- PLIED. CHECK POINT Do you open the water tap? Is the filter of the water inlet valve clogged with dirt? Is the water pressure sufficient? (0.
26 TROUBLE SHOOTING PROBLEM W A TER SUP - PL Y IS NOT STOPPED. CHECK POINT Does the water supply continue while the power is turned off? Does the water supply start as soon as you press the power swit.
27 TROUBLE SHOOTING PROBLEM THE W ASHER DOES NOT DRAIN. CHECK POINT Do you install the drain hose properly? Is the foreign matter accumulated inside the pump housing? Is the output voltage of the drain pump normal? CAUSE SOLUTION Install the drain hose properly .
28 TROUBLE SHOOTING PROBLEM THE W ASHER DOES NOT SPIN. CHECK POINT Is the lid open? Does the safety switch operate normally? Does the pulsator rotate while the tub does not rotate? Is the connector of P .
29 TROUBLE SHOOTING NO NO PROBLEM THE INDICA- TOR LAMPS(L.E.D) DO NOT LIGHT UP WHEN THE POWER BUT- TON IS PRESSED. PROGRESS LAMPS(LED) DO NOT LIGHT UP .
9. PRESENT A TION OF THE P .C.B ASS’Y 30 PCB ASS’Y MESSAGE CAUSE SOLUTION Improper installation of drain hose. The drain hose is blocked up by foreign matter . Drain motor is inferior . The water tap is closed. The water inlet filter clogged. It passes over the 30 minutes, yet it doesn’t come to assigned water level.
APPENDIX 31 WIRING DIAGRAM § § Wiring Diagram [non-pump].
32 WIRING DIAGRAM § § [Non-Pump, Single Valve].
33 WIRING DIAGRAM § § [Pump].
34 WIRING DIAGRAM § § [pump, single valve].
35 P AR TS DIAGRAM § § Parts Diagram.
36 P AR TS DIAGRAM § § Parts List NO. P ART NAME P ART CODE SPECIFICA TION REMARK A01 PLA TE T 3614521500 PP A02 DOOR B AS 361 1797600 ABS OPTION : A03 DOOR F AS 361 1797700 ABS TRANSP ARENT A04 DOO.
37 P AR TS DIAGRAM NO. P ART NAME P ART CODE SPECIFICA TION REMARK 3612787945 5A COLD/HOT NON-BUBBLE DUAL V AL VE, PUMP 3612787970 8A COLD/HOT BUBBLE A26 HARNESS AS 3612787975 5A COLD/HOT BUBBLE DUAL V AL VE 3612787980 8A COLD/HOT NON-BUBBLE 3612787985 5A COLD/HOT NON-BUBBLE 361 1337000 F H05VV 3X0.
38 P AR TS DIAGRAM.
39 P AR TS DIAGRAM § § Parts List NO. P ART NAME P ART CODE SPECIFICA TION REMARK B01 CABINET 3610809600 P AINTED STEEL SHEET 0.6T B02 HANDLE CABINET 3612603300 PP B03 PLA TE UPPER 3614521600 PP B04.
40 P AR TS DIAGRAM.
41 P AR TS DIAGRAM § § Parts List NO. P ART NAME P ART CODE SPECIFICA TION REMARK C01 BALANCER AS 3616104700 DWF-6010 C02 TUB I 3618808500 SUS 0.5T C03 TUB U 3618808601 PP ST AINLESS STEEL C04 GUIDE FIL TER 3612507000 DWF-6010NP C05 SPECIAL SCREW 3616003700 SUS 5.
42 P AR TS DIAGRAM.
43 P AR TS DIAGRAM § § Parts List NO. P ART NAME P ART CODE SPECIFICA TION REMARK D01 COVER TUB O 361 1414600 PP D02 TUB O 3618817600 PP D03 SUSPENSION AS F 3619804200 FRONT D04 SUSPENSION AS B 3619.
44 CIRCUIT DIAGRAM § § Circuit Diagram 1. DWF-750/752/803/805/753/755/803/805.
45 2. DWF-756/758/806/808.
S/M NO. : WF750SE001 DAEWOO ELECTRONICS CO., L TD. 686, AHYEON-DONG MAPO-GU SEOUL, KOREA C.P .O. BOX 8003 SEOUL, KOREA TELEX: DWELEC K28177-8 CABLE: “DAEWOOELEC” F AX: 82-2-360-7877 TEL: 82-2-360-71 14 http://www .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Daewoo DWF-805 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Daewoo DWF-805 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Daewoo DWF-805, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Daewoo DWF-805 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Daewoo DWF-805, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Daewoo DWF-805.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Daewoo DWF-805. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Daewoo DWF-805 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
