Manuel d'utilisation / d'entretien du produit 917.27631 du fabricant Craftsman
Aller à la page of 56
Owner's Manual ICHFT=MeN, I GARDEN TRACTOR 24.0 HP, 48" Mower Electric Start 6 Speed Transaxle Model No. 917.276310 This product has a low emission engine which operates differently from previously built engines. Before start the you engine, read and understand this Owner's Manual.
Warranty ................................................ 2 Safety Rules .......................................... 3 Product Specifications ........................... 5 Assem bly/Pre-Operation ....................... 7 Operation ....................
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death.
II. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Opera- tion on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.
PRODUCT SPECIFICATIONS Gasoline Capacity 5 Gallons and Type: Unleaded Regular Oil Type SAE 30 (above 32°F) API-SG-SL): SAE 5W30 (below 32°F) Oil Capacity: W/Filter: 4.0 Pints W/O Filter: 3.75 Pints Spark Plug: Champion QC12YC (Gap: .040") Ground Speed Lo: Hi: (MPH): 0.
Keys (1) Oil Drain Tube Far Future Use Slope Sheet Your new tractor has been assembled at the factory. When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating posi- tion (seated behind the steering wheel).
TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls) _h, WARNING: Before starting, read, un- derstand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H L I',,I "re, FAST REVERSE NEUTRAL HIGH LOW CHOKE SLOW IGNITION .
KNOW YOU R TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.
The cutting height range is approximately 1-1/2" to 4-1/2". The heights are mea- sured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.
3. Look down and behind before backing. 4. Move gear shift lever to reverse (R) po- sition and slowly release clutch/brake pedal to start movement. 5. When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.
depress clutch/brake pedal and set parking brake. 2. Place gear shift lever in neutral (N) position. 3. Move attachment clutch to disengaged position. 4. Move throttle control to fast position 5. Pull choke control out for a cold engine start attempt.
MAINTENANCE SCHEDULE o_._,_'_ o_. __ _o_ o_._ AS¥OUCOMPLETB REou A SE V,CE ," C :i:: _ B_raek p r eOper a: ion _ Check Operator Presence and T ROS Systems R Check for Loose Fasteners _ _1_5.
TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
• To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructionssupplied with balancer.) NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered,but are not.
Oil Drain Valve To Open To Close J 2. Reinstall precleaner cartridge, cover and secure. IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean the cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge.
1. With engine cool, remove filter and plug fuel line sections. 2. Place new fuel filter in position in fuel line with arrow pointingtowards carbu- retor. 3. Be sure there are no fuel line leaks and clamps are properly positioned. 4. Immediately wipe up any spilled gaso- line.
8. Raise attachment lift to its highest posi- tion. 9. Slide mower forward and remove belt from electric clutch pulley. 10. Slide mower out from under right side of tractor. TO INSTALL MOWER Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control.
• If links are not equal in length, adjust one link to same length as other link. • To lower front of blade, loosen nut "C" on both front links an equal number of turns. NOTE: Each full turn of nut "C" will change distance "B" by approximately 3/16".
10.Check primary idler arm and two idlers to see that they rotate freely. 11. Be sure spring is securely hooked to primary idler arm and spring arm. MOWER DRIVE BELT INSTALLATION 12. Install belt in both idlers. 13. Install new belt onto electric clutch pul- ley.
TO ADJUST ATTACHMENT CLUTCH The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required.
Clutching Flat Engine Belt Kee Clutchin eper Transaxle Pulley Twists Belt Keeper TO ADJUST STEERING WHEEL ALIGN- MENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal.
4. Install new battery with terminals in same position as old battery. 5. Reinstallterminal guard. 6. First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely. 7. Connect BLACK grounding cable to negative (-) battery terminal with re- maining hex bolt and keps nut.
TO ADJUST CARBURETOR Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to a Sears or other qualified ser- vice center for repair and/or adjustment. High speed stop is factory adjusted.
Immediately prepare your tractor for stor- age at the end of the season or if the trac- _,wAWill not be used for 30 days or more. RNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start Hard to start Engine will not turn over Engine clicks but will not start CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center CAUSE 3ORRECTION , PROBLEM Lossofpower Excessive vibration Engine dies when tractor is shifted into reverse Engine continues to run when oper- ator leaves seat with attachement clutch engaged , 3.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Mower blades will not rotate Poor grass discharge CAUSE CORRECTION 1. Remove obstruction. 1. Obstruction in clutch mechanism. 2. Worn/damaged mower drive belt.
TRACTOR- - MODEL NUMBER 917.276310 SCHEMATIC 02832-193394193395 BATTERY ERP BCS LTWITR BYPASS SWITCH / ELECTRIC CLUTCH SOLENOID FUSE PTO REVERSE SWITCH _ . SHORT_NG CONNECTOR I NOT]N REVERSE ELECTRIC CLUTCH AMMETER (OPTIONAL) k A2 i 1 77 _2 IGNITION SWITCH eL_CK/W'_ IGNITION .
ELECTRICAL 24 42 TRACTOR -- MODEL NUMBER 917.276310 22 I / I I I I I I 41 i F / 34 33 I I , 30 I I 1933941 I I I 32.
ELECTRICAL TRACTOR- - MODEL NUMBER 917.276310 KEY PART NO. NO. DESCRIPTION 1 144927 Battery 2 74760412 Bolt Hex Head 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt 1/4-20 x 7.
TRACTOR - - MODEL NUMBER 917.276310 CHASSIS AND ENCLOSURES t61 162_ 28 21 ,17 20 lS 148 17 7_ 17 16 56 j152 167 ! _7 17 172 139 85 17 67 63 17 45 17 150 153 130 122 17 17 34.
TRACTOR- - MODEL NUMBER 917.276310 CHASSIS AND ENCLOSURES KEY PART KEY NO. NO. DESCRIPTION NO. 1 180375 Rail, Frame RH 63 2 175282 Drawbar, Gt 66 4 73680700 Nut, Crawnlock Hex 7/16-14 unc 67 5 193636X.
TRACTOR - - MODEL NUMBER 917.276310 GROUND DRIVE 28 9 38 / 36 _46 13 44 10_ 57 69 J61 157 _155 54 66 67 _5 drive 9-vgt 62 36.
TRACTOR- - MODEL NUMBER 917.276310 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 3 7563R Washer, Thrust, Axle 40 178575 4 17490508 Screw Thdrol 5/16-18 x 3/4 41 73931000 5 STD541437 Nut, .
TRACTOR - - MODEL NUMBER 917.276310 STEERING ASSEMBLY 21 J 2O 23 34 33 42 22 36 / J ' steering.2Owgt 52 J J 38.
TRACTOR- - MODEL NUMBER 917.276310 STEERING ASSEMBLY KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 26 27 28 29 31 32 33 34 35 36 41 42 45 51 52 53 PART NO. DESCRIPTION 186093X428 Wheel, Steering 178557 Axle Asm., Front 183226 Fitting, Grease 161849 Spindle Asm.
ENGINE TRACTOR - - MODEL NUMBER 917.276310 21 J 18 15 4s_ 47_ 37 I 84 12 41 85 69 /81 26 _ 37 / 27 39 engine ELS 1-vgt 29 / I SPARK ARRESTER KIT I KEY PART NO.
TRACTOR - - MODEL NUMBER 917.276310 SEAT ASSEMBLY / / I ....--. 16 I I I I % ° 18 19 12 I 37 21 seat5wgt KEY PART NO. NO. 1 180598 2 180166 3 140675 5 145006 6 STD541437 7 124181X 8 171877 10 1801.
DECALS TRACTOR- - MODEL NUMBER 917.276310 18 6 5 19 17 5 10 KEY PART NO. NO. DESCRIPTION 1 195838 Decal, Chassis 3 186242 Decal, Hood, RH 4 186243 Decal, Hood, LH 5 186725 Decal, Hood Side Panel 6 133.
LIFT ASSEMBLY 4O 39 42 TRACTOR - - MODEL NUMBER 917.276310 43 38 3 10 , I 23 70 _ I - 79_ 6 23 7O 76 _26 _2_3__75 =_ 78 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 121006X Red Asm,, Lever 34 137167 2 180045 Shaft Asm., Lift Vgt 35 138057 3 159189 Lever Asm.
TRACTOR - - MODEL NUMBER 917.276310 MOWER DECK 46 132 95 112 I 21 122_ 33 >30 18 29 24 26 44.
TRACTOR- - MODEL NUMBER 917.276310 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 180358 Deck Weldment Mower 48 50 72110612 3 178915 Bracket Asm., Sway Bar 52 175820 5 4939M Retainer Spring 56 155986 6 178024 Arm, Suspension, Rear (Sway Bar) 57 156941 8 174365 Bolt 7/16 Asm.
TRANSAXLE TRACTOR - - MODEL NUMBER 917.276310 8O 3 2O 5 4 7 L 74 70 84 90 "k _ 9 g4 * '_e 73 72 14 25 24 46.
TRANSAXLE TRACTOR- - MODEL NUMBER 917.276310 KEY PART NO. NO. 1 4197R 2 12000034 3 4199R 4 4216R 5 4215R 6 4217R 7 174728 8 74020652 9 7392M 10 137261 11 4985R 12 6266H 13 4212R 14 137125 15 6276H 16 .
TRACTOR -- MODEL NUMBER 917.276310 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446677-0470-E1 213_ 216 1 222267g t88_:_ 265 [_ 267 d [_ 718 26 847_ 523 842 525_ 287 _/_ 1019 LABEL KIT ] 1330 REPAIR MANU.
TRACTOR -- MODEL NUMBER 917.276310 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446677-0470-E1 D 35 36 _ 1022 1029 1100 798 3o 36 1022 11oo _oo,% 1_ 3j _83_ _ _ 78 _ 5°°_ I _r_/I 387 _- o28 " 918 .
TRACTOR - - MODEL NUMBER 917.276310 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446677-0470-E1 789A 3o3{ 332 75@ 573 _ 405 358 ENGINE GASKET SET 20 @ 163 276 @ 868 943 @ 1022 _ 524 ' 691 695_ 3091 .
TRACTOR - - MODEL NUMBER 917.276310 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446677-0470-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 699753 Cylinder Assembly 133 499803 2 499585 Ki.
TRACTOR -- MODEL NUMBER 917.276310 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446677-0470-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 405 697820 Screw (Back Plate) 865B 691015 418 6909.
.
.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION _ ARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees, Make turns gradually to prevent tipping or loss of control.
Your Home For repair - in your home - of all major brand appliances. lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 917.27631 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 917.27631 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 917.27631, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 917.27631 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 917.27631, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 917.27631.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 917.27631. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 917.27631 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
