Manuel d'utilisation / d'entretien du produit 917.272281 du fabricant Craftsman
Aller à la page of 60
Owner's Manual ICRRFTSMRWI LAWN TRACTOR 22.0 HP, 42" Mower Electric Start Automatic Transmission Model No. 917.272281 This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual.
Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications .......................... 6 AssemblyPre-Operation ....................... 8 Operation .........................
IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. Look for this symbol to point out • Do not mow in reverse unless absolutely important safety precautions.
DO: • Mow up and down slopes, not across. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Uneven terrain could overtum the machine. Tall grass can hide obstacles. • Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope.
• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless abso- lutely necessary. Always look down and behind before and while backing.
3RODUCT SPECIFICATIONS Gasoline Capacity and Type: Oil Type (API-SF-SJ): 4 Gallons Unleaded Regular SAE 30 (Above 32°F) SAE 5W-30 (Below 32°F) Oil Capacity: 4.0 Pints Spark Plug: Champion RC12YC (GAP: .040") Ground Speed Forward: 5.5 (MPH): Reverse: 2.
Mower ,__ _Ora, n','_ Leveling For Future Use Wrench I Slope Sheet Bubble Level Video Cassette 7.
Your new tractor has been assembled at the factory. Review the video cassette before you begin. When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating position (seated behind the steering wheel).
TO ROLLTRACTOR OFF SKID (See Operetion section for location and function of controls) 1. Press lift lever plunger and raise attachment lift lever to its highest position.
CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factoryfor shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shownin "PRODUCT SPECIFICATIONS" section of this manual.
These symbols may appear on your tractor or in literature supplied with the product. Leam and understand their meaning. BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING ENGINE ON ENGINE OFF OIL PR.
KNOWYOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.
TO USE CRUISE CONTROL The cruise control feature can be used for forward travel only. 1. With forward ddve pedal depressed to desired speed, move cruise control lever forward to =SET" position and hold while lifting your foot off the pedal, then release the cruise control lever.
• To restart movement, slowly release parking brake and brake pedal. • Slowly depress appropriate drive pedal to slowest setting. • Make all turns slowly. TO TRANSPORT When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position.
NOTE: Before starting, read the warm and coldstarting procedures below. 6. Insert key into ignition and tum key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute.
MOWING TIPS • Mower should be propedy leveled for best mowing performance. See rl'O LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has already been cut.
M.,.'rO.A.C,= SC.,=OU.,= AS YOU COMPLETE REGULAR SERVICE DE DATES Check Operator Presence and T Interlock Systems V' R crux+< _" Loose Fasteners IfP I_s I_' _ SharpeNReplace Mow.
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
• Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for I hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers.
7. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see =PRODUCT SPECIFICATIONS" section of this manual. 8. Use gauge on oil fill cap/dipstick for checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick.
CLEANING Clean en_line, battery, seat, finish, etc. of all matter. foreign Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automo- tive type wax.
7. Install front plate assembly to tractor suspension brackets and retain with single loop retainer springs as shown. 8. Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate and mower brackets.
• Before making any necessary adjust- ments, check that both front plate links are equal in length. • If links are not equal in length, adjust one link to same length as other link. • To lower front of mower loosen nut =1£' on both front links an equal number of turns.
TO ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle. If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.
TRANSMISSION REMOVAUREPLACE- MENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor.
7. Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely 8. Close terminal access doors. 9, Close hood. Hex Bolt Keps Nut Terminal Door Cable ,Negative Guard (Black) Cable TO REPLACE HEADLIGHT LAMP CAUTION: When lit, the halogen lamps get extremely hot.
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ,_ CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART:. See appropriate section In manual unless directed to Sears service center PROBLEM Will not start Hard to start Engine will not turn over CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. Engine clicks but will not start 4.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center CAUSE PROBLEM Loss of power contlnued) Excessive vibration Engine continues Io run when )perator leaves seat with _ttachment :lutch engaged _oorcut-uneven 3.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Mower blades will 2. Worn/damaged mower 2. Replace mower drive belt. not rotate (con't) drive belt. 3. Frozen idler pulley. 3.
TRACTOR -- MODEL NUMBER 917.272281 SCHEMATIC IGNmON SWITCH SEAT SWITCH (NOT OCCUPIED) , i ! _ ......... = b FUEL ' _ OPERATOR PRESENCE KUE i LINE J A RELAY #t i__ _ SPARK ' = IGNITION PLUG .
ELECTRICAL TRACTOR -- MODEL NUMBER 917.272281 26 40 if i ! j! I f I I I J 34.
TRACTOR -- MODEL NUMBER 917.272281 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt, Hex 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt, Btr Front 1/4-20 x 7-1/2 11 150109 H.
TRACTOR - - MODEL NUMBER 917.272281 CHASSIS AND ENCLOSURES 42 29 215 39 2O9 166 2O 23 2OO 3 2O9 36.
TRACTOR-- MODEL NUMBER 917.272281 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis 2 176554 3 17060612 Screw, 3/8-16 x 3/4 9 172542)(418 Dash 11 174996 Panel, Dash, I_H 10 72140608.
TRACTOR -- MODEL NUMBER 917.272281 GROUND DRIVE 32 _52 253 77 F 241 244 226 62 36 24 26 26 22 38.
TRACTOR -- MODEL NUMBER 917.272281 GROUND DRIVE KEY PARr KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 ...... Transaxle (See Breakdown) 77 Hydrogear Model 323-O510 78 6 17060512 Screw 5/16-16 x 3/4 89 9 137140 Clutch Elec 90 124346X 15 74490544 Bolt He)( Flghd 5/16-18 Gr.
TRACTOR -- MODEL NUMBER 917.272281 STEERING ASSEMBLY 88 J I 29 67 lO 36 4o 43 40.
TRACTOR - - MODEL NUMBER 917.272281 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 175139X418 StasdngWheel 2 172393 Axle Assembly 3 169840 Spindle Assembly, LH.
TRACTOR -- MODEL NUMBER 917.272281 ENGINE 32 14 38 29 I OPTIONAL EQUIPMENT I Spark Arrester I 42.
TRACTOR -- MODEL NUMBER 917.272281 ENGINE KEY PART NO. NO. DESCRIPTION 1 175437X505 ContmI, Throffia 2 164863 Screw Hwhd H.-Lo #13016 x 3/4 3 ....... Engine, (See Breakdown) B&S Model Number 44677.
TRACTOR- - MODEL NUMBER 917.272281 SEAT ASSEMBLY KEY PART NO. NO. 1 175134 2 14O551 3 71110616 4 19131610 5 145OO6 5 STD541437 7 124181X 8 17000616 9 19131614 10 182493 11 177957 12 121246X 13 121248X KEY PART DESCRIPTION NO.
DECALS TRACTOR -- MODEL NUMBER 917.272281 13 6 3 18 15 18 11 10 KEY PART NO. NO. 1 180978 2 174969 3 17"/909 4 177910 6 133644 7 181604 8 179128 9 182168 10 156439 11 181470 12 146046 13 177890 14 160396 9 14 KEY PART DESCRIPTION NO. NO. Decal, Hood/Seat 15 181427 Reflector LH.
TRACTOR - - MODEL NUMBER 917.272281 LIFT ASSEMBLY 37 38 4O 41 13 4 6 13 19 13 32 19 32 $4 46.
TRACTOR-- MODEL NUMBER 917.272281 LIFT ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 179.504 Plunger Assembly 2 159476 Shaft Assembly, Lift 3 178981 Pin, Groove 4 12000002 E-Ring 5 19211621 Washer 21/32x 1 x21 Gauge 6 120183X Bearing, Nylon 7 175830 Grip, Handle, Ruted 11 139865 Unk, Lift, LH.
TRACTOR -- MODEL NUMBER 917.272281 MOWER DECK 140- 117 11 137 21 25 I h '1 h 29 27 48.
TRACTOR -- MODEL NUMBER 917.272281 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 182032 Mower Deck Assembly, 42" 68 174883 2 STD533107 Boll 91 180532 3 138017 Bracket Aos.
18 124 6.Sealant (Jolt d' etancheb) 57-20W50 Oil - 78.80Z (OZ de 78.820 d' Huile) 127 - Seal and O-ring Kit (Phoque 0 Sonne Jeu) 88 128 i ,=0 ! I | oi: oO m_ r M ZF € z _c W m_ _m.
TRACTOR -- MODEL NUMBER 917.272281 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 3230510 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 1_1 Main Housing,Assembly 67 170413 2 170_52 Side Housing, .
TRACTOR -- MODEL NUMBER 917.272281 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446777 TYPE NUMBER 0165-E1 89g 1 213_ 216 1 ,o i' "_ 878 ' 87 tL 718 I 1019 L.
TRACTOR -- MODEL NUMBER 917.272281 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446777 TYPE NUMBER 0165-E1 121 CARBURETOR OVERHAUL KIT 51 L(,._,_(_,,J 276 _) 633e 987 • 104 117 • __ 1124 gG' Q 137 s,s2A @ 742 4O4O 691 0 977 CARBURETOR GASKET SET 51 _ _e 987 D 150 276 0 1124 _ 2tt _1_ 108 ,t_ I ,_ t 11311130 S6 .
TRACTOR -- MODEL NUMBER 917.272281 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446777 TYPE NUMBER 0165-E1 7, | =,T 4O5 48 358 ENGINE GASKET KiT 3_ 163 275 O 691 o% 797 Y 54.
TRACTOR -- MODEL NUMBER 917.272281 BRIGGS & STRATTON ENGINE-MODEL NUMBER 446777 TYPE NUMBER 0165-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION I 694001 .
TRACTOR - - MODEL NUMBER 917.272281 BRIGGS & STRA'I-rON ENGINE-MODEL NUMBER 448777 TYPE NUMBER 0165-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO.
57.
.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION 1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge Is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure.
For repair of major brand appliances i in your own home... no matterwho made it, no matter who sold it! 1-800-4-MY-HOME _ AnyOne, day or nigl_ (1-8(X_ (U.S.A. and Canada) _M For repair of carry-in products like vacuums, lawn equipment, and electronics, call for the nearestSears Parts and Repair Center.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 917.272281 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 917.272281 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 917.272281, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 917.272281 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 917.272281, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 917.272281.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 917.272281. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 917.272281 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
