Manuel d'utilisation / d'entretien du produit 247.775890 du fabricant Craftsman
Aller à la page of 28
Owner's Manual 10 Horse Power CHIPPER-SHREDDER Model No. 247.775890 I I E CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Printed in U.
Content Page Content Page Warranty information 2 Service & Adjustment 15 Safe Operation Practices 3 Off-Season Storage 18 Assembly 5 Trouble-Shooting 19 Operation 8 Parts List 20 Maintenance 12 On.
This symbol points outimportant safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper shredder.
shut off. Never place any part ofthe body in the impeller area until you are sure the impeller has stopped rotating. • Muffler and engine become hot and can cause a bum. Do not touch. • Do not allow leaves or other debris to build-up on engine's muffler.
I Rear 2 Bottles of OII Hopper" Chipper Chute Discharge Chute * The hopper is packed in _e top Insert In your chipper-shredder carton. Figure I :hlp Bag Spark Plug Wire Figure 2 IMPORTANT: This unit is shipped without gasoline or oil in the engine.
I Hex Nut J Step 1 Hinge Discharge Chute Wing Knob Figure 3 • Place second spacer over hex bolt inside the other part of the hinge as shown in the inset, Secure tightly with hex lock nut. • Secure both sides of discharge chute to housing using wing knobs that you earlier removed.
• Raise the hopper till it clicks into position. • Unscrew the shoulder bolt from the stop washer on the inlet guide. See Figure 6. • Align the loose end of the flap control rod with the stop washer on the inlet guide. • Slide the shoulder bolt through the opening in the flap control rod.
Read this owner's manual and safety rules before operating your chipper-shredder. Compare Figure 9 with your chipper-shredder to familiarize yourself with thelocation of various controls and adjustments.
Lowering Hopper Assembly In order to rake leaves into the hopper, you will need to lower the hopper. • To lower the hopper assembly, use one hand to grasp the hand-hold at the top of the hopper assembly and lift slightly. See Figure 5. • Pul! up on the release bar, and lower the hopper assembly to the drop-down position.
A WARNING: Do not fill closer than 1/2 inch from the top of the fuel tank to prevent spills and to allow for fuel expansion. If gasoline is accidently spilled, move chipper- shredder away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared.
h, hopper assembly when it is in the raised or lowered position. See Figure 13. Bulky material, such as stalks or heavy branches, up to 3" in diameter should be fed into the chipper chute. See Figure 13. A WARNING: Do not put material larger than is specified into the hopper, and/or into the chipper chute.
General Recommendations • Always observe safety rules when performing any maintenance, • The warranty on this chipper shredder does not cover items that have been subjected to operator abuse or negligence.
the oilmust be to FULL mark on dipstick. Change engine oilevery 50 hours of operation under normal operating conditions. Change oil every 25hours when operating nder heavy load or in high temperatures. To Drain Oil Drain oilwhile engine is warm. Follow instructions .
head, top of piston and around valves. Use a soft brush to remove the deposits. Reassemble gasket and cylinder head. Turn screws down finger-tight. Torque cylinder head screws in a staggered sequence to 165 in.-Ibs. ,_ WARNING: Temperature of muffler and nearby areas may exceed 150 ° F(65°C).
Removing Flail Screen if the discharge area becomes clogged, remove the flail screen and clean area as follows. • Stop engine, make certain the chipper- shredder has come to a complete stop and disconnect spark plug wire from the spark plug before unclogging the chute.
Pipe Weld Bolt Allen Screw When reassembling the blade, tighten center bolt to between 550-700 inch-pounds and the two outer bolts to 250-300 inch-pounds, or lacking torque wrench, tighten securely.
Check idle speed and re-adjust to 1750 rpm, if necessary. Engine should accelerate smoothly, If it does not, adjust idle mixture valve counter-elcckwise 1/8 turn. _lb ARNING: Air cleaner and its cover must be assembled to the carburetor before starting the engine.
Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store machine with fuel in the fuel tank inside of building where.
Problem Corrective Action Engine fails to start Loss of power; operation erratic Engine overheats Too much vibration Unit does not discharge Possible Cause 1. Fuel tank empty, or stale fuel 2. Spark plug wire disconnected 3. Faulty spark plug 4. Fuel shut-off valve not turned ON.
CRAFTSMAN 10 H.P. CHIPPER SHREDDER MODEL 247,775890 2O.
CRAFTSMAN 10 H.P. CHIPPER SHREDDER MODEL 247.775890 Key No. I 2 3 4 5 6" 7 8 9 10 11 12 13 14 15 16 17 18 19 2O 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 4O 41 42 44 Part No.
CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDER MODEL NO. 247.775890 Key No. Part No. 1 495631 2 495657 3 .391086 5 214347 7 _.272163 8 498038 9 _27803 10 94621 11 280819 13 945.
CRAFTSMAN 10 H,P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDER MODEL NO, 247.775890 Key No. Part No. Description 12 15A 16 77 18 19 20 21 22 24 25 26 27 28 29 30 32 33 34 35 40 45 46 146 219 2.
CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432*1182-E1 FOR CHIPPER SHREDDER MODEL NO. 247.775890 Kay No. Part No. 50 51 51A 53 93 " 94 95 98A 104 105 106 108 123 125 127 130 131 133 137 138 141 142 14.
CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDER MODEL NO. 247.775890 Key No. 116 209 211 212 212A 227 232 284 422 523 524A 525 562 592 623 624 847 Part No. Description *270920 Seal-O-Ring 263212 Spring-Governor 263182 Spring-Governor Idle 263051 Link-Throttle 263049 Link-Throttle 499096 Lever.
CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDER MODEL NO. 247.775890 Key No, 23 24 37 38 73 74 75 215 304 305 363 575 1036 Part No. Description 298260 Flywheel 222698 Key-Flywheel 222475 Guard-Flywheel .94811 Screw-Hex. 224874 Screen-Rotating 94680 Screw-Hex.
.
For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For in-homemajor brand repair service Call 24 hours a day, .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 247.775890 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 247.775890 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 247.775890, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 247.775890 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 247.775890, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 247.775890.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 247.775890. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 247.775890 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
