Manuel d'utilisation / d'entretien du produit 2100 du fabricant 3M
Aller à la page of 30
Model 2100 (4100) Overhead Pr ojector 78-6970-1335-3 9/92 3M Austin CenterBuilding A145-5N-01 Austin, TX 78726-9000 Visual Systems Division Ser vice Man ual (Order the M2100 Illustrated Parts Breakdow.
9/92 MODEL 2100 OVERHEAD PROJECTOR TITLE PAGE NUMBER TABLE OF CONTENTS T echnical Suppo r t Hotline - 1-800-328-1371 ( U .S . & Canada) Section 1 - Introductio n ................................................................................ . 1-1 Specification s .
9/92 MODEL 2100 OVERHEAD PROJECTOR This ser vice manual contains ser vicing instruction, troubleshooting guide , adjustments, electr ical diag rams , assembly/dis-assemb ly of par ts and the illustrated par ts list. ANGULAR BODY (2130/4130, 2140/4140, 2160, 2170) ROUND BODY (2150/4150, 2180) SPECIFICATIONS Physical Width - 15.
9/92 MODEL 2100 OVERHEAD PROJECTOR 1-2.
9/92 MODEL 2100 OVERHEAD PROJECTOR 2130/2140/2150 4130/4140/41 50 2160/2170/2180 2160/2170/2180 100VAC 50/60HZ 3.6 Amps 14-1/2' (4.4mm) ------- F4 Amp - 250 Volt 220/230/240VAC 50HZ 1.7 Amps 14-1 /2' (4.4mm) VDE, NEMKO, SETI SEMKO, SEV F4 Amp - 250 Volt 120/127/VAC 60HZ 3.
9/92 1-3 MODEL 2100 OVERHEAD PROJECTOR PRINCIPLES OF OPERATION Optics (See Figure 1-2) The light source for the Overhead Projector is 275 watt, 24 volt, Tungsten Lamp listed as ANSI Code FNT and rated at 75 hours. An external reflector is needed with this lamp.
9/92 2-1 MODEL 2100 OVERHEAD PROJECTOR SET UP PROCEDURE 1 . Connect the power cord to a properly grounded electrical outlet. (Electrical requirements are listed on the serial plate located under the base of the projector.) 2. Place the projector on a level surface and turn the projector on by pushing down on the ON/OFF switch.
9/92 MODEL 2100 OVERHEAD PROJECTOR 2-2 A. Pull the mirror down as the FOCUS CORRECTION LEVER is pushed to the rear of the head assembly. B. Raise the mirror back to the original position and refocus using the FO- CUS KNOB. 6. Rotate the Color Tuning Knob until the projected image is free of any yellow or blue corners.
9/92 MODEL 2100 OVERHEAD PROJECTOR LAMP MANAGEMENT SYSTEM (Lamp Indicator) Pertains only to models equipped with lamp indicators. (2130/4130 - No holes, opaque) NOTE When the projector is turned on, the red X will momentarily light. This is a characteristic of the projector.
9/92 MODEL 2100 OVERHEAD PROJECTOR 2-4 CLEANING The optical components of the overhead pro- jector require occasional cleaning to remove the dust and oil which tends to accumulate and absorb light. 3M Brand Lens Cleaner (Part No. 78-6969-7086-6) is recommended.
9/92 2-5 MODEL 2100 OVERHEAD PROJECTOR LUBRICATION As needed and upon new parts installation, lubricate lightly the following area with Anderol No. 757 Grease (3M Part No. 78- 8000-8079-4). For reference on the lubricating points, see the three blow-up parts lists.
9/92 3-1 MODEL 2100 OVERHEAD PROJECTOR SECTION 3 - TROUBLESHOOTING SYMPTOM CHECK CAUSE/SOLUTIONS Projected image is: a. Corners of projected image appear red (brown) or blue. b. Top, bottom, or sides of projected image are not focused. c. Not as bright as it should be.
9/92 MODEL 2100 OVERHEAD PROJECTOR 3-2 TROUBLESHOOTING (continued) SYMPTOM CHECK CAUSE/SOLUTIONS Fan motor does not rotate, but lamp does energize. Both lamps of units with lamp changer energize at once. Projector does not operate when power switch is depressed.
9/92 4-1 MODEL 2100 OVERHEAD PROJECTOR GENERAL The following section describes the adjustments that will be necessary to service the Model 2100 (4100) Overhead Projectors. TOOLS REQUIRED A. Screwdriver (standard & phillips) B. Wrench, open end C. Pliers, standard D.
9/92 1. Select a 60 by 60 inch, smooth area on one wall. Place a sturdy bench or test stand about 8 feet from this wall area. Position the Overhead Projector on the test stand so that it points toward the wall. 2. Measure the vertical distance from the floor to the center of the front projection lens.
9/92 4-3 MODEL 2100 OVERHEAD PROJECTOR OPTICAL ALIGNMENT Proper alignment of the optical system is essential for good resolution and uniform illumination. Poor resolution in one corner and either red or blue in the corners of the projected image are indications of poor alignment.
9/92 MODEL 2100 OVERHEAD PROJECTOR 4-4 FOCUS MECHANISM If the projection head does not hold its focus position, you must adjust focus knob tension or add focus kit (78-8054-1613-4 (gray), 78-8054- 1614-2 (charcoal). To adjust: Turn the Tension Screw counterclockwise to tighten focus assembly.
9/92 4-5 MODEL 2100 OVERHEAD PROJECTOR COLOR TUNING CABLE (Before Serial Number 422868) NOTE Tension in cable should be 3/16" maximum. A. Raise the Top Cover Assembly by pulling the Release Latch and lift up. (See Figure) B. Turn the Color Tuning Knob clockwise to the maximum.
9/92 MODEL 2100 OVERHEAD PROJECTOR 4-6 POST (FOLDING) If POST is not perpendicular to the body of the projector, proceed with the following steps using Figures below as reference: 1. Loosen SET SCREW. 2. Put a square on the body of the projector and against the POST> 3.
9/92.
9/92.
9/92.
9/92.
9/92.
9/92.
9/92.
9/92.
9/92 6-1 MODEL 2100 OVERHEAD PROJECTOR SECTION 6 DISASSEMBLY/RE-ASSEMBLY TOP COVER ASSEMBLY 1. Raise the Top Cover Assembly by pulling the Release Lever and lifting up. 2. Using both hands, pull either one of the two hinges outward until the hinge pin is out of the hole.
9/92 6-2 MODEL 2100 OVERHEAD PROJECTOR STAGE GLASS 1. Remove Top Cover Assembly.(See page 6- 1) 2. Remove the Fresnel Lens. (See page 6-1) 3. Remove the six (6) tamper proof screws using a T15 Torx Driver. (3M Part Number 26-1005-8317-3) 4. Remove the MASK (black frame) and Stage Glass.
9/92 How to remove and install the condenser lens (when equipped) Caution! Wear safety glasses when removing lens. 1. Insert a Pin Punch or Drill Rod into the hole in the Tab (see illustration A) 2. Release the lens by bending the Tab. 3. Install the new lens and bend the Tab back into place.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté 3M 2100 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du 3M 2100 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation 3M 2100, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le 3M 2100 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le 3M 2100, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du 3M 2100.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le 3M 2100. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei 3M 2100 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
