Manuel d'utilisation / d'entretien du produit MSEBX900 du fabricant Compaq
Aller à la page of 53
Detailed USER M A NU AL FOR: EBX smartModule800/900 MSEBX800/900 Nordstrasse 11/F CH - 4542 Luterbach Tel.: ++41 (0)32 681 58 00 Fax: ++41 (0)32 681 58 01 Email: support@digitallogic.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 2 For internal use only: File: MSEBX800 -900_Detailed_V1.0.doc Path: R:HANDBUCHMS EBXMSEBX 800MSEBX800-90 0_Detailed_V1.0.doc COPYRIGHT 2008 BY D IGITAL -LOGIC A G This publication is protected by copyright and all rights are reserve d.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 3 Table of Content s 1. P REFACE ........... ......................................... ........................................ ......................................... ................ 5 1.1. Trademark s .
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 4 7.2. Th e 3pin Jumpers ........................................ ......................................... ........................................ 50 7.3. Jumpers on the M SEBX800 ................
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 5 1. P REF A CE The inf ormation conta ined in this m anual has been carefull y ch eck ed and is believed to be accurate; it is subject to change without not ice. Product ad vances m ean that som e specif ications m ay ha ve ch anged.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 6 1.5. Recycling Infor mation All com ponents within t his product f ulfill the req uirements of the R oHS ( Restrictio n of Hazardous Su bstances Directive). The pro duct is solder ed with a lead f ree proc ess.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 7 1.8. Explanation of Symbols CE Conformity This symbol indicates that the product described in this manual is in complian ce with all applied CE stan dards.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 8 1.9. Applicable Doc uments and Sta ndards The following publication s are used in conj unction with t his m anual. W hen an y of the referenced specifications are s uperse ded b y an appro ved revis ion, t hat rev ision s hall a pply.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 9 Sm art Battery Data Spec ification Re vision 1.1, Decem ber 11, 1998. www.sbs-f orum .org System Managem ent Bus (SM Bus) Specificat ion Vers ion 2.0, Au gust 3, 200 0 Copyright © 1994, 1 995, 1998, 2000 Duracell, Inc.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 10 RoHS is often refer red to as the "lead-free" directi ve but it res tricts the use of the f ollowing substances: Lead Mercur y Cadm ium Chrom ium VI PBB a nd PBDE The m aximum a llowable concentration of any of the a bove mentioned substances is 0.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 11 1.12. Swiss Qualit y 100% Made in S witzerland DIGIT AL-LOGIC is a m ember of "Swiss-Label" T his product was not manufact.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 12 2. O VERVIEW 2.1. Standard Feat ures The MICRO SPACE E BX is a m iniaturized m odular device incorporating the m ajor elements of a PC/AT compatible com puter.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 13 2.4. Block Diagrams 2.4.1. MSEBX800.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 14 2.4.2. SM800.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 15 2.5. MSEBX800/900 Specifications CPU Specification CPU SM800 AMD GEODE LX 800/900 located in the sm artModule800/900 CPU Core Sup ply 1.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 16 External Interface s Specification Video Interfaces CRT1, DVO USB V1.1/2.0 4 Ports LPT IEEE1293 Printer COM1 RS232 COM2 RS232 COM3 - COM4 - Keyboard PS/2 Mouse PS/2 Floppy 26pin FCC Inter face for TEAC Mini-Flopp y Parallel-Hard disk 2.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 17 Operating T emperature Specification: MIL-810-501 MIL-810-502 Extended tem perature r ange: SM800PCX (500 MHz) -40° C to +70° C Security e1 No.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 18 2.6. Examples of Or dering Codes The MSEBX800 s ystem is c ombined from : Baseboard MSEBX8 00 smartModule 8 00/900-xxx ( must be ordered s eparately ) Memor y: SODIMM200-DDRAM ( must be ord ered separately) Article Part No.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 19 2.7. Dimensions & D iagrams MSEBX800.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 20.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 21.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 22 2.8. Incompatibilitie s to a Standard PC/ A T None. 2.9. MSEBX800/900 Related A pp lication Notes # Description 80 High fr equency Radiation (t o m eet EN55022) Application Notes are avail ble at http://www.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 23 2.11. Thermoscan Product Par t Numb er Serial Number Version MSEBX800 811202 45320210010 0.2 SM800PCX 805164 45316410032 2.1 SODIMM DDR 1G B 870672 - - Software W indows XP SP2 running desk top Top view, passive cooled: t [min] fCPU [MHz] I [A] P [W] 60 500 0.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 24 3. P REP A R A TION 3.1. Important Infor mation Warning, ESD Sens itive Device! Place the em bedded c omputer bo ard on an isolated, ESD-protected s urface. Also ensure t hat all equipment, tools an d peopl e are fully protect ed agains t ESD.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 25 3.2. Mounting the s martModule Line up the holes in the s mar tModule o n the MSEBX board (top side). Then on the re verse side, attach the smartModule usi ng 4 Phillips head s crews (c ircled in red, within the red fr ame mark ing the approxim ate location of the sm artModule).
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 26 3.3. RAM A sse mbl y/Disassembl y To install or cha nge the RAM, f ollow these ste ps: 1. Unmount the sm artModule b y removing the 4 sc rews m ark ed in red ( see the phot o fr om the previous page).
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 27 e. Slowly push the R AM down unt il the clips "click " into place (Ph oto 3). Photo 3 3.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 28 3.4. Power & Reset Buttons Power Butto n: Push the Power Bu tton for 2 sec onds to start u p the system .
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 29 4. B US S IGNALS 4.1. PC104 Bus Note... The ISA-Bus m ay have som e minor incom patibilities, see Cha pter 6. AEN, output Address Enable: used to degat e the m icroprocess or and other devices from the I/O channel to allo w DMA transfer s to take place.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 30 /Master, input This signal is used with a D RQ line to gain control of the system. A processor or DMA contro ller on the I/O channel m ay issue a DRQ to a DMA channe l in casc ade mode and recei ve a /DAC K.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 31 /SMEMW , input/output These signals instruct the m em ory devices to store the data pr esent on the data b us f or the first MByte. / SMEMW is active in all m emor y read c ycles. /SMEMW may be dr iven by an y m icroprocessor or DMA c ontroller in t he system .
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 32 5. D ET A ILED S YS TEM D ESCRIPT ION 5.1. Boot Time System Boot T imes Definitions/Boot- M edium Quick Boot* Normal Boot MSEBX800-500MH z with RT C-Backup Batter y Memor y 256MB shared 8MB f or Video time [s] From Flopp y disk Boot from Setup-Disk1 MS-DO S v6.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 33 5.2. Interfaces 5.2.1. PS/2 Key board (AT Compatible) an d PS/2 Mouse X31 Key board Pin Sign al Pin Signal 1 KB_Dat a 2 - 3 GND 5 +5Volt / 1 00mA 6 KB_Clk 8 - X32 Mouse Pin Sign al Pin Signal 1 MB_Data 2 - 3 GND 5 +5Volt / 1 00mA 6 MB_Clk 8 - 5.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 34 5.2.4. Floppy Disk Interface Supported Flopp y Format s Capacity Drive size Tracks Dat a rate DOS version 1.2 MB 5-1/4" 80 500 KHz 3.0 - 6.22 720 K 3- 1/2" 80 250 KH z 3.2 - 6. 22 1.44 M 3-1/2 " 80 500 KHz 3.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 35 5.3. Controllers 5.3.1. Interrupt Control lers An 8 259A com patible inter rupt controller , within t he c hipset, pro vides seven prioritized interr upt levels.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 36 5.4. BIOS Reco very In case the BIOS needs to be rec overed: 1. Set Jum per J9 . 2. Start the MSEBX800/900. 3. Open the BIOS. 4. Rem ove Jumper J9 . 5. Load the def ault BIOS set tings. 6. Save the sett ings.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 37 6. D ESCRIPTION AND L O C A TION OF THE C ON NECTORS Connector Structure Pin Remarks X1 Power Input 2 Power Jack X2 ATX Power Connec tor 20 X11 LVDS 2x 10 RM2.5 4 X14 Video IN 2 SMA X15 LCD 2x 25 RM2.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 38 6.1. Connector Plan.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 39 6.2. Connector Des criptions X1 Pow er Input Pin Sign al Pin Sign al 1 8-30V DC- Input 2 Ground X2 ATX Con nector Pin Sign al Pin Sign al 1 +3.3V 2 +3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 PW R-OK 9 +5VSB 10 +12V 11 +3.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 40 X15 LCD Connector Pin Sign al Pin Sign al 1 DE_SP LIT 2 VSYNC 3 BLK 4 HS YNC 5 VCCLC D_SB 6 Ground 7 NC 8 SHFCLK 9 VDD 10 D0 11 D1 12 D2 13 D3 1.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 41 X30A Printer Port (Cen tronics, EM I-Filt ered) D-SUB Connect or: Signal Pin 1 Strobe Pin 2 Data 0 Pin 3 Data 1 Pin 4 Data 2 Pin 5 Data 3 Pin 6 .
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 42 X31 PS/2Keyboard ( AT Compatib le) Pin Sign al Pin Signal 1 KB_Dat a 2 - 3 GND 5 +5Volt / 1 00mA 6 KB_Clk 8 - X32 PS/2M ouse Pin Sign al Pin Sig.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 43 RJ45 Connector 10BaseT ( IEEE 802.3i), 100Ba seTX (IEEE 802.3u): MDI- Pin EIA/TIA 568 A colors (wire/line) Pin Twisted Pair TX+ W hite / Green 1 3 TX- Green 2 3 RX+ W hite / Orange 3 2 GND .. 4 1 GND .
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 44 X52 AVR Pin Sign al Pin Signal 1 AVR VCC 2 GND 3 AVR SC L 4 AVR RST 5 AVR MI SO 6 AVR MOSI Only for internal use X53 Utility Pin Sign al Pin Sig.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 45 X62 3.5" Hard Dis k Pin Sign al Pin Signal 1 Reset (ac tive low) 2 GND 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 46 X100 PC/104 Conne ctor (IS A) Pin A: B: C: D: 0 Ground Ground 1 IOCHCK Ground SBHE MEMCS16 2 SD7 RESET LA23 IOCS16 3 SD6 +5V LA22 IRQ10 4 SD5 IR.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 47 X101 PC/104+ Conn ector (PCI) Pin A: B: C: D: 1 GND/5.0 V KEY2 R eserved +5 AD00 2 VI/O AD02 AD01 +5V 3 AD05 GND AD04 AD03 4 C/BE0* AD07 GND AD06 5 GND AD09 AD08 GND 6 AD11 VI/O AD10 M66EN 7 AD14 AD13 GND AD12 8 +3.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 48 X120 M iniPCI Interface Pin Sign al Pin Signal Pin Signal Pin Signal 1 T IP 2 RING 63 3.3V 64 FRAME# 3 8PMJ-3 4 8PMJ-1 65 CLKRUN# 66 T RDY# 5 8PMJ-6 6 8PMJ-2 67 SERR# 68 ST OP# 7 8PMJ-7 8 8PMJ-4 69 GROUND 70 3.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 49 X130 PCI Slot (Standa rd PCI Sl ot) Pin Name PCI Pin Descript ion Pin Name PCI Pin Descript ion A1 TRST Test Logic Reset B1 -12V -12 VDC A2 +12V.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 50 7. J UMPER L OC A TIONS O N THE B O A RD The f ollowing tables sho w the location of the jum per blocks on th e MSEBX8 00/900 board. The num bers shown in thes e tables are silk screened on the board so that t he pins can be easil y located.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 51 7.3. Jumpers on the MSEBX800.
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 52 8. I NDEX A Addressing PCI Devic es............................................. 31 B BIOS Recovery .......................................................... 36 Block Diagrams ..................
DIGITAL-LOGIC AG MSEBX800/900 Det ailed M anual V1.0 53 Mounting................................................................ 25 Specifications ............................................................. 15 SQS....................................
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Compaq MSEBX900 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Compaq MSEBX900 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Compaq MSEBX900, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Compaq MSEBX900 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Compaq MSEBX900, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Compaq MSEBX900.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Compaq MSEBX900. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Compaq MSEBX900 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
