Manuel d'utilisation / d'entretien du produit AIR-CAP1702I-E-K9 du fabricant Cisco
Aller à la page of 40
G ETTING S TARTED G UIDE Cisco Aironet 1700 Series Access Points 1 About this Guide 2 Introduction to the Access Point 3 Safety Instructi ons 4 Unpacking 5 Configuratio ns 6 Access Point Ports and Con.
2 OL-32413-01 Last Updated: December 12, 2014.
3 1 About this Guide This Guide provides in structions on how to inst all and configure your Cisco Aironet 1700 Series Access Point. This guide also provides mounting in structions and limited troubleshooting procedures. The 1700 Series Access Point is referred to as the access point in this document.
4 – Throughput, forwarding, and filtering performance scaled to meet 2 spatial streams, 1.3-Gbps data-rates • 64 MB flas h size • 802.3af/802.3at compatible via CDP (Cisco Disco very Protocol) or LLDP (Link Layer Discovery Protocol) • 2.4 GHz and 5 GHz 802.
5 War n in g Installation of the equipme nt must comply with local and national electric al codes. Statement 1074 War n in g This product relies on the building’ s installation for short-circ uit (overcurrent) protection. Ensure tha t the protective device is rated not greater than: 20A.
6 4 Unpacking T o unpack the access point , follow these steps: Step 1 Unpa ck and remove the access po int and the accessory kit from the shipping box. Step 2 Re turn any packing material to the shippi n g container and save it for future use. Step 3 V erify that you hav e received the items listed below .
7 Countries Supported Click this URL to browse to a list of countrie s and regulatory domains supported by the 1700: www.cisco.com/go/aironet/compliance 6 Access Point Ports and Connectors The 1702I model access point has integrated antennas a nd has an LED indicator on top of the unit, as shown in Figure 1 .
8 Figur e 2 Access P oint P o rts and Conn ec tions (bot tom)-AIR1 702I M odel 1 Kensington lock slot 4 Auxiliary Ethernet Port 2 DC Power connection port 5 RS232 Console Port 3 Primary Ethernet port .
9 Note The Auxiliary Ethernet port is disabled. Do not connect this port to a PoE switch. Connecting the primary and auxiliary ports to a PoE sw itch will not provide additional power . 7 Configuring the Access Point This section describes how to connect the access point to a wireless LAN controller .
10 Note Y ou cannot edit or query any ac ce ss point using the controller CLI i f the name of the access point contains a space. Note Make sure that the controller is set to the curren t time.
11 • Access point mounting options: below a suspended ceiling, on a fla t horizontal surface, or on a desktop. Note Y ou can mount the access point above a su spended ceiling but you must purcha se additional mounting ha rdware: See “Mounting th e Access Po int” sec tion on pag e 14 for additional information.
12 Pre-Installation Configuration Setup The pre-installation configuration setup is shown in Figure 3 . Figure 3 Pre-Installation Confi guration Setup T o perform pre-installati on configuration, perform the following steps: Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the n etwork.
13 e. CAPW AP UDP ports must not be blocked in the network. f. The access point must be able to find the IP address of the controller . This can be accomplished using DHCP , DNS, or IP subnet broadcast. This guide describes the DHCP method to convey the controller IP addres s.
14 Step 5 If y our access point does not indicate normal operatio n, turn it off and repeat the pre-installation configuration. Note When you are installing a La yer 3 access point on a different subn.
15 c. (Only for APs in Unified configuration) If the LED blinks sequentially for more than 5 minutes, the access point is unable to find its pr imary , secondary , and tertiary Cisco wireless LAN controller.
16 Using DHCP Option 43 Y ou can use DHCP Option 43 to provide a list of c ontroller IP addresses to the access points, enabling them to find and jo in a controller . F o r additional information, refer to the “Configuring DHCP Option 43 and DHCP Option 60” section on pag e 37 .
17 Operating status Blinking amber Software upgrade in pro gress Cycling through green, red, and amber Discovery/join process in progress Rapidly cycling through red, green, and amber Access point loc.
18 Troubleshooting the Ac cess Point Join Process Note The controller must be running Cisco IOS Softwar e Release 8.0.x.x or later to support 1700 series access points. A detailed explanation of th e join process is on Cisco.com at the following URL: http://www.
19 • An existing access point running software release 8. 0.x.x or later has been reset after clearing the configuration. If any of these conditions are met and the access point has n ot yet joined a controller , y ou can also configure a DHCP server to return a sys log server IP address to the access point using opti on 7 on the server .
20 11 Declarations of Conformity and Regulatory Information This section provides declarations of conformity and regulatory information for the Cisco Aironet 1700 Series Access Points.
21 This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limit s are designed to provide reaso nable protection against harmful interference when the equi pment is operated in a residential environment.
22 VCCI Statement for Japan War n in g This is a Class B product based on the standard of the V oluntary Control Council for Interf erence from Informatio n T echnology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference.
23 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interf erence when operating Cisc o Aironet access points in Japan.
24 Statement 371—Power Cable and AC Adapter English Translation When installing th e product, please use the provided or designated connection cables/power cables/AC adaptors.
25 Cisco Aironet Access Points are cert ified to the requiremen ts of RSS-210. The use of this device in a system operating either parti ally or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.
26 Les utilisateurs êtes avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) p our les bandes 5 250-5 350 MH z et 5 650-5 850 MHz et que ces radars pourraient causer du brouilla ge et/ou des dommages aux dispositifs LAN-EL.
27 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC.
28 The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure ref erred to in Article 10.
29 This device also conforms to the EMC requirem ents of the Medical Devices Directi ve 93/42/EEC. Note This equipment is intended to be used in a ll EU and EFT A countries. Outdoor u se may be restricted to certain frequencie s and/or may require a license fo r operation.
30 As such the systems are desi gned to be operated as to avoid contact with the antennas by the end user . It is recommended to set the system in a location where the antennas can remain at least a m.
31 This Device Meets the In dustry Canada Guidelines for Exposure to Radio Waves The 1700 series device includes a radio transmi tter an d receiver . It is designed not to exceed the limits for exposure to radio waves (radio frequency electrom agnetic fields) as referenced in Heal th Canada Safety Code 6.
32 Santé Canada affirme que la littérature scientifiq ue actuelle n'indique pas qu'il faille prendre des précautions particulières lors de l'utilisation d'un appareil sans fil.
33 Chinese Translation.
English Translation Administrative Rules for Low- power Radio-Frequency Devices Article 12 For those low-power radio-frequenc y devices that have alr eady recei ved a type-a pproval , compani es, business units or users should not change its freque ncies, increase its power or change its original features and functions.
35 English Translation Low-power Radio-frequency Devices T echnical Specifica tions Operation of Cisco Aironet Access Points in Brazil This section contains special information for oper ation of Cisco Aironet access points in Brazil.
36 Figur e 4 Br azil Regulat ory Inf or mation Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e nã o po de causar interferência a sistemas operando em caráter primário.
37 12 Configuring DHCP Option 43 and DHCP Option 60 This section contains a DHCP Option 43 configu ration example on a Windows 2003 Enterprise DHCP server for use with Cisco Aironet lightweig ht acce ss points. For other DHCP server implementations, consult product documentation for configuring DHCP Option 43.
38 <Default router> is the IP address of the default router, such as 10.0.0.1 <DNS Server> is the IP address of the DNS server, such as 10.0.10.2 Step 3 Add the option 6 0 line using the following syntax: option 60 ascii “ VCI string ” For the VCI string , “Cisco AP c1700”.
.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliate s in the U.S. and other countries. T o view a list of Cisco trademarks, go to this URL: www.cisco .com/go/trademarks . Third-party trad emarks mentio ned are the p roperty of t heir respec tive owners.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cisco AIR-CAP1702I-E-K9 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cisco AIR-CAP1702I-E-K9 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cisco AIR-CAP1702I-E-K9, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cisco AIR-CAP1702I-E-K9 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cisco AIR-CAP1702I-E-K9, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cisco AIR-CAP1702I-E-K9.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cisco AIR-CAP1702I-E-K9. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cisco AIR-CAP1702I-E-K9 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
