Manuel d'utilisation / d'entretien du produit PT Cruiser convertible (2005) du fabricant Chrysler
Aller à la page of 360
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number ............... 6 䡵 V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1 I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
I n f o r m a t i o n P r o v i d e d b y :.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 2 ▫ Ignition Key Removal ................... 1 2 ▫ Locking Doors W ith The Key .............. 1 4 ▫ Key-In-Ignition Reminder ...............
䡵 Remote Keyless Entry ..................... 2 1 ▫ T o Unlock The Doors ................... 2 1 ▫ T o Lock The Doors ..................... 2 2 ▫ Horn Chirp Feature ..................... 2 2 ▫ Using The Panic Alarm .................. 2 2 ▫ T o Program T ransmitters .
䡵 Engine Break-In Recommendations ........... 5 6 䡵 Safety T ips ............................ 5 7 ▫ Exhaust Gas .......................... 5 7 ▫ Safety Checks Y ou Should Make Inside The V ehicle .............................. 5 7 ▫ Periodic Safety Checks Y ou Should Make Outside The V ehicle .
A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer . Ask your dealer for these numbers and keep them in a safe place. The double sided keys may be inserted into the locks with either side up.
NOTE: If you try to r emove the key before you place the lever in P ARK, the key may become trapped temporarily in the ignition cylinder . If this occurs, r otate the key to the right slightly , then remove the key as described.
W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever . Don’t leave the keys in the ignition.
chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regar dless of whether or not the vehicle is locked or unlocked.
All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. Automatic T ransaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in P ARK and the shift knob push-button is out.
W ARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death.
Central Locking/Unlocking All vehicle doors and deck lid are locked with the first turn of the key to the LOCK position. The double unlock activation featur e requir es you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors at once.
2. Cycle the ignition switch ON/OFF four times ending in the OFF position. 3. Pr ess the interior door lock switch to the LOCK position. 4. A single chime will sound to signify that you have successfully completed the programming. Y ou can turn the feature back on by repeating the above mentioned procedur e.
T o Lock The Doors: Press and release the LOCK button to lock all doors. The park lights will flash and the horn will chirp to acknowl- edge the signal. Horn Chirp Feature The horn chirp that signals that the doors have been locked can be turned on or off by using the following procedur e: 1.
T o Program T ransmitters Up to four transmitters can be programmed to your vehicle. Y our new vehicle was shipped with two trans- mitters. See your dealer for additional transmitters. Additional transmitters can be programmed to the sys- tem by using the following procedur e: 1.
T ransmitter Battery Service The recommended replacement battery is 2016 or its equivalent. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. W ith the transmitter buttons facing down, use a thin coin to pry the two halves of the transmitter apart.
SECURITY ALARM SYSTEM The system monitors the doors, deck lid, and ignition switch for unauthorized operation. If something triggers the alarm, the system will signal for about 18 minutes. For the first 3 minutes the horn will sound and the headlights, park lights, tail lights and the indicator light in the cluster will flash.
T o disarm the system: Unlock a front door/deck lid using either the key or the Keyless Entry T ransmitter . Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm.
T o open the deck lid, insert the key into the lock and turn to the right. The deck lid can also be opened using the remote keyless entry or by using the power deck lid release switch, located in the glove box. W ARNING! • Driving with the deck lid open can allow poison- ous exhaust gases into your vehicle.
EMERGENCY DECK LID RELEASE LA TCH W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the deck lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
The lower left switch controls the left rear passenger ’ s window and the lower right switch contr ols the right r ear passenger ’ s window . W ARNING! Never leave children in a vehicle, with the keys in the ignition switch.
Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down.
Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “ click. ” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
4. Position the lap belt across your thighs, below your abdomen. T o r emove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
6. T o release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point.
2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 ° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack fr om the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver ’ s front airbag is mounted in the center of the steering wheel.
If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them.
Airbags inflate in moderate to high speed impacts. Along with seat belts and pr etensioners, fr ont airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger . Side airbags also work with seat belts to impr ove occupant protection.
2. All occupants should wear their lap and shoulder belts properly . 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door , airbags will inflate forcefully into the space between you and the door .
The front airbag system consists of the following: • Airbag Control Module (ACM) • AIRBAG Readiness Light • Driver and Passenger Front Airbag/Inflator Units • Unique Steering Wheel and Column .
bolster , instrument panel and the steering wheel and column. If the key is in the OFF position, in the ACC position, or not in the ignition switch, the airbags are not on and will not inflate.
panel. The passenger ’ s fr ont airbag gas is vented through vent holes in the sides of the airbag. In this way the front airbags do not interfere with your control of the vehicle. • The Knee Impact Bolsters help protect the knees and position you for the best interaction with the front airbags.
If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you.
Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces requir e that small childr en ride in proper r estraint systems. This is the law , and you can be prosecuted for ignoring it.
Infants And Small Children There are differ ent sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner ’ s manual to ensure you have the correct seat for your child.
• The belt-positioning booster seat is for childr en weigh- ing mor e than 40 lbs (18 kg), but who are still too small to fit the vehicle ’ s seat belts properly . If the child cannot sit with knees bent over the vehicle ’ s cushion while the child ’ s back is against the seat back; they should use a Belt Positioning Booster Seat.
that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child ’ s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint.
around, and insert the latch plate into the buckle again. If you still can ’ t make the child restraint secure, try a differ ent seating position. • Buckle the child into the seat according to the child restraint manufacturer ’ s directions.
to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. NOTE: If your child restraint seat is not LA TCH com- patible, install the restraint using the vehicle seat belts.
• Check belt fit periodically . A child ’ s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty . SAFETY TIPS Exhaust Gas W ARNING! Exhaust gases can injure or kill.
Front seat belt assemblies must be r eplaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor , torn webbing, etc. If there is any question regar ding belt or retractor condition, replace the belt.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Convertible T op Operation ................. 6 2 ▫ T o Lower The T op ...................... 6 2 ▫ T o Raise The T op ...................... 6 6 ▫ Convertible T op Boot Cover Installation – If Equipped .
▫ Driver ’ s Seat Back T ilt ................... 8 2 ▫ Passenger Seat Back T ilt (Easy Entry System) . . . 83 ▫ Adjustable Head Restraints ............... 8 5 ▫ Heated Seats — If Equipped .............. 8 6 ▫ Folding Rear Seat ..........
䡵 Electronic Speed Control .................. 1 0 3 ▫ T o Activate .......................... 1 0 3 ▫ T o Set At A Desired Speed ............... 1 0 4 ▫ T o Deactivate ........................ 1 0 4 ▫ T o Resume Speed ..................... 1 0 4 ▫ T o V ary The Speed Setting .
CONVERTIBLE TOP OPERA TION W ARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision.
CAUTION! T o fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position (automatic transaxle) or in the Neutral position (manual transaxle) before lowering or raising the top. CAUTION! Do not operate the convertible top with ice or snow build-up on the top.
1. T urn the ignition key to the ON position. 2. Release the top from the windshield header by pulling down on the latch handle and turning the latch handle clockwise until it stops. 3. Press the Power T op Switch to disengage the top pins from the header , turn the handle counterclockwise and raise the handle to the stowed position.
4. Continue pressing the Power T op Switch until the convertible top is lowered completely . 5. Install the Convertible T op Boot Cover , if equipped. Refer to Convertible T op Boot Cover Installation – If Equipped, in this section.
T o Raise The T op: CAUTION! T o avoid damage to the convertible top or its com- ponents, your vehicle is equipped with a feature that prevents convertible top operation at speeds over 10 mph (16 km/h).
5. Raise the latch handle into the stowed position. CAUTION! Car top carriers, ski racks, etc., should not be at- tached to the convertible top mechanism as they will damage the top. Do not place objects on the convert- ible top, in the top well or on the sport bar .
Convertible T op Boot Cover Installation – If Equipped 1. W ith the top down and the convertible top latch handle in the stowed position, lay the unfolded boot cover across the convertible top.
2. Install the rear edge of the boot, first tucking the rear edge of the boot under the rear and both sides of the rails. T ucking Boot Under Rail UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 69 3 I n.
3. Pull the right and left boot arms forward and engage both boot arm snaps. Make sure both snaps are fully engaged. 4. Engage the boot center section retainer using the tabs provided.
5. T uck the rear flap of the boot in behind the Upper Moulding. T ucking In Rear Flap UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 71 3 I n f o r m a t i o n P r o v i d e d b y :.
Convertible T op Boot Cover Removal and Storage 1. Unsnap the snaps and remove the top cover boot. 2. Lay the boot cover flat with the center section retainer facing the rear of the car . 3. First fold the left side of the boot cover to the middle of the boot cover .
4. Second fold the right side of the boot cover to the middle, fitting it inside the left side of the boot cover and store it in the trunk or a dry secure area. CAUTION! Do not lay heavy objects on top of the boot or lay the boot on top of sharp/pointy objects.
2. T urn the screw counter clockwise until the scr ew stops. This will relieve the hydraulic pressure and allow the convertible top to be raised manually . 3. Using the latch handle raise the top until the two pins seat themselves in the windshield header .
MIRRORS Inside Compass/T emperature Mirror This manual day-night inside rearview mirror has an integrated compass and outside temperature display , along with dual map/courtesy lamps with switches for independent operation. These lamps also turn on to- gether with the dome lamp.
Lights • Briefly press the “ Right ” button to toggle the right reading lamp “ ON/OFF ” . Repeat the key press to cycle the light. • Briefly press the “ Left ” button to toggle the left reading lamp “ ON/OFF ” . Repeat the key press to cycle the light.
Compass V ariance • Find your current location and determine the correct Zone number from the map. • Press and hold the “ Left ” button for 5 – 10 seconds (until “ Zone ” appears in the display), then release the button. The number displayed is the current Zone value.
Compass Calibration If “ CAL ” is not displayed, press and hold the “ Left ” button for 10 – 15 seconds, until “ CAL ” appears in the display , then release the button.
Electric Remote-Control Mirrors Use the mirror select switch, located to the left of the steering column on the instrument panel, to adjust the view obtained in the outside mirrors. Press the L or R button for Left or Right mirror selection. Use the center off position to guard against accidentally moving a mirror position.
Illuminated V anity Mirrors An illuminated vanity mirror is on the sun visor . T o use the mirror , rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically . Closing the mirror cover turns off the lights. SEA TS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor .
Using body pressur e, move forward and rearwar d on the seat to be sure the seat adjusters have latched. W ARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
Reclining Bucket Seats The recliner contr ol is on the outboard side of the seat. T o recline, lean forward slightly before lifting the lever , then lean back to the desired position and release the lever . Lean forward and lift the lever to return the seatback to its normal position.
NOTE: The driver ’ s front seat has a full recliner memory , which will allow the seat back to return to its original position. Passenger Seat Back Tilt (Easy Entry System) How to operate the passenger front seat: 1. Rotate fr ont seat handle rearward until seat back releases.
3. Continue pushing the entir e seat forward until it slides toward the dashboard. 4. T o return seat to a sitting position, rotate seat back upright until it locks. 5. Push seat rearward until the track locks. NOTE: The passenger front seat has a full recliner memory , which will allow the seat back to returned to its original position.
Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear . Pull up or push down on the head restraints so that the upper edge is as high as practical. T o raise the head restraint, pull up on the head restraint.
Heated Seats — If Equipped This featur e heats the fr ont driver ’ s and passenger ’ s seats. The control for the heater is located on the out- board side of each seat. After turning on the ignition, you may choose from HIGH, or LOW heat settings.
Folding Rear Seat T o pr ovide additional storage ar ea, each rear seatback can be folded forward. The seat back r elease knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
T o tumble the seat forward use the following procedure: 1. The seat back release knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
2. From inside the vehicle, fold the rear seat back down flat. 3. Pull the release handle located at the bottom of the folded seat back and tumble the seat forward.
4. Attach the cinching tether strap, located at the side of the seat cushion, onto the hook bar on the center trim panel and tighten by pulling the cinching strap until the seat is secure. T o return the tumbling rear seat to the latched (normal) position use the following procedur e: 1.
NOTE: Prior to rotating the seat cushions r eward, be sure that the rear seat belt buckles are secured with the straps, so that the buckles are accessible. NOTE: Prior to lifting either seatback to the upright position, be sure that the seat belt is brought forward to avoid trapping it behind the seatback.
TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Then move the safety catch located under the front edge of the hood, near the center and slightly to the right, and raise the hood.
W ARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. Y ou could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Interior Lights The interior lights come on when a door or the deck lid is opened.
Interior light Defeat (OFF) Rotate the dimmer control to the ex- treme bottom “ OFF ” position. The in- terior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (white semi-circle).
Headlights, Parking Lights, Instrument Panel Lights T urn the end of the Multi-Function Control Lever to the first detent for parking light operation. T urn to the second detent for headlight operation. T o change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.
Fog Lights The front fog light switch is on the Multi-Function Control Lever . T o activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control lever . NOTE: The fog lights will only operate with the head- lights on low beam.
WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch on the control lever . The lever is located on the right side of the steering column. Move the con- trol lever up to select the desired wiper speed. Windshield Washers T o use the washer , pull the control lever toward you and hold while spray is desired.
CAUTION! In cold weather , always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.
Adding W asher Fluid The fluid r eservoir is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at r egular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water .
TIL T STEERING COLUMN T o tilt the column, push down on the lever below the multi-function control lever and move the steering wheel up or down, as desired. Pull the lever back up to lock the column firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous.
TRACTION CONTROL SWITCH — IF EQUIPPED The TRAC indicator , located in the instrument cluster , will flash when the T raction Control System is in use. The TRAC OFF switch is located on the instrument panel below the radio. T o turn the system OFF , press the TRAC OFF switch until the TRAC OFF indicator in the instrument cluster lights up.
NOTE: The T raction Control System indicator “ TRAC OFF ” will illuminate momentarily as a bulb check, each time the ignition switch is turned ON. This will occur even if you used the “ TRAC OFF ” switch to turn the system OFF . NOTE: The T raction Control System will make buzzing or clicking sounds when the system is in operation.
W ARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. Y ou could accidentally set the system or cause it to go faster than you want. Y ou could lose control and have an accident. Always leave the system OFF when you are not using it.
T apping “ ACC/RES ” once will result in a 2 mph (3 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 6 mph (10 km/h), etc. T o decrease speed while speed control is ON, push down and hold “ COAST/SET ” .
V ehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “ stop and reverse ” feature as required by federal safety stan- dards.
W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
5. The indicator light in the Universal T ransceiver will begin to flash, first slowly and then rapidly . The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the pr ocedure.
NOTE: The assistance of a second person may make the following programming procedure quicker and easier . 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer .
The Universal T ransceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor .
2. This device must accept any interference that may be received including interference that may cause undesir ed operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user ’ s authority to operate the equipment.
Another of the outlets is in the Accessory Switch Bank, in the center of the instrument panel. This outlet is powered directly by the battery , regar dless of the ignition switch position. All accessories connected to this outlet should be removed or turned off when the vehicle is not in use, to pr otect the battery against discharge.
Since this outlet is remote from the driver , it is powered by the ignition switch, only when it is in the ⬙ ON ⬙ or ⬙ ACCESSOR Y ⬙ positions, to pr otect the battery against discharge. Note: Neither of the power outlets will accept a cigar lighter unit.
CONSOLE FEA TURES The console has two front cup holders, a coin holder , 12 volt power outlet, and front and rear storage trays. There are additional cup holders; one is molded in the center of the console to hold large cups and the other is at the rear of the console to serve passengers in the rear seat.
CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle ’ s battery , even when not in use; i.e. cellular phones, etc. Eventually , if plugged in long enough, the vehicle ’ s battery will discharge suf ficiently to degrade battery life and/or prevent engine start- ing.
Storage Pockets There are also Storage pockets located on each door trim panel. UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 117 3 I n f o r m a t i o n P r o v i d e d b y :.
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Features ................. 1 2 3 䡵 Instrument Cluster ...................... 1 2 4 䡵 Instrument Cluster — T urbo, W ith AutoStick .... 1 2 5 䡵 Instrument Cluster — T urbo, W ithout AutoStick .
▫ T uning ............................. 1 3 7 ▫ Radio Data System (RDS) ............... 1 3 7 ▫ PTY (Program T ype) Button .............. 1 3 7 ▫ Balance ............................ 1 3 9 ▫ Fade .............................. 1 3 9 ▫ T one Control .
▫ Mode .............................. 1 4 4 ▫ T ape CD Button ...................... 1 4 4 ▫ T ime Button ......................... 1 4 5 ▫ Scan Button ......................... 1 4 5 ▫ CD Changer Control Capability — If Equipped .........
▫ CD Changer Control Capability — If Equipped ....................... 1 5 7 ▫ Radio Display Messages ................ 1 5 8 䡵 Sales Code RBQ — AM/FM Stereo Radio W ith 6 - Disc CD Changer .................... 1 5 9 ▫ Radio Operation ......
INSTRUMENT P ANEL FEA TURES UNDERST ANDING YOUR INSTRUMENT P ANEL 123 4 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER 124 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER — TURBO, WITH AUTOSTICK UNDERST ANDING YOUR INSTRUMENT P ANEL 125 4 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER — TURBO, WITHOUT AUTOSTICK 126 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Charging System Light This light shows the status of the electrical charg- ing system.
6. Engine T emperature W arning Light This light warns of an overheated engine condi- tion. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out.
9. Speedometer Indicates vehicle speed. 10. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever toward the steer- ing wheel to switch the headlights from high or low beam.
out of the retractor . This is a reminder to “ buckle up ” .I f you do not buckle up, the light will remain on. 14. Brake System W arning Light This light monitors various brake functions, including brake fluid level and parking brake application.
The light will also come on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. If the parking brake is off and the light remains on, have the brake system inspected as soon as possible.
and trip distance. In the trip odometer mode, holding the trip button for more than 2 seconds will reset the trip odometer to “ 0 ” . 19. Cruise Indicator — If Equipped This indicator shows that the Speed Control System is ON. NOTE: The word “ SET ” will not illuminate when the Speed Control System is on.
disabled for about 4 minutes until the brakes have cooled. The system will automatically r eactivate and turn off the TRAC OFF Light. 22. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems.
25. AutoStick Gear Position — If Equipped This vacuum fluorescent display indicator illuminates when the gearshift lever is moved to the AutoStick position and shows the current gear selection. 26. Fuel Door Reminder This symbol is a reminder that the Fuel Filler Door is located on the front passenger ’ s (right) side of the vehicle.
RADIO GENERAL INFORMA TION Radio Broadcast Signals Y our new radio will pr ovide excellent reception under most operating conditions. Like any system, however , car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning.
remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE RAZ — AM/ FM STEREO RADIO WITH CASSETTE T APE PLA YER, CD PLA YER AND CD CHANGER CONTROLS Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch.
T uning Press the TUNE control up or down to increase or decrease the frequency . If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed.
Program T ype Radio Display Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R &.
Pressing PTY , then SCAN will scan the FM Band and stop at all RDS stations. Each RDS station will be played for a 5 second scan once around the FM Band and stop at the last station. The PTY icon will then turn off. Balance The Balance control adjusts the left-to-right speaker bal- ance.
T o Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory , press the SET button. SET 1 will show in the display window . Select the push-button you wish to lock onto this station and press and release that button.
Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
Pinch Roller Release If ignition power or the radio ON/OFF switch ar e turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player , the pinch roller will automatically reengage and the tape will resume play .
If the volume control is ON, the unit will switch from radio to CD mode and begin to play . The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: • Y ou may eject a disc with the radio OFF .
FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner . Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play .
Time Button Press this button to change the display from elapsed CD playing time to time of day . Scan Button Press this button to play the first 10 seconds of each track.
CD Diagnostic Indicators When driving over a very r ough r oad, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically . As a safeguard and to protect your CD player , one of the following warning symbols may appear on your display .
Operating Instructions NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. NOTE: When first learning the control functions, the user should set the controls as shown in the following list.
T une Press the TUNE control up or down to increase or decrease the frequency . If the button is pushed and held, the radio will continue to tune until the button is released. The frequency will be displayed and continu- ously updated while the button is pushed.
Bass and T reble T one Control The tone controls consist of 2 separate bands. The bass band is on the left, and the treble band is on the right. Each band is adjusted by a slider control with a detent at the mid-position. Moving the control up or down in- creases or decreases amplification of that band.
beginning of the previous selection if the tape is within the first 5 seconds of the current selection. The SEEK symbol appears on the display when Music Search is in operation. Music Search shuts off automati- cally when a selection has been located.
CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The fol- lowing instructions ar e for the radio controls that operate this CD changer . Mode Button T o activate the CD changer , press the MODE button until CD information appears on the display .
A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected.
SALES CODE RBK — AM/ FM STEREO RADIO WITH CD PLA YER AND CD CHANGER CONTROLS Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Balance The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out.
both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory . The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed.
If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day . If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number and index time in minutes and seconds.
Mode Press the MODE button repeatedly to select between the CD player , the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “ SA ” will appear in your radio display . A CD or tape may remain in the player while in the Satellite mode.
Random Play (RND) Press the Random button to play the tracks on the selected disc in random or der for an inter esting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer . CD Diagnostic Indicators When driving over a very r ough r oad, the CD player may skip momentarily .
SALES CODE RBQ — AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER RBQ Radio UNDERST ANDING YOUR INSTRUMENT P ANEL 159 4 I n f o r m a t i o n P r o v i d e d b y :.
Radio Operation Power/V olume Control Press the PWR/VOL control to turn the radio on. T urn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
Balance — BAL The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The Fade control provides for balance between the front and rear speakers.
General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
show the disc number , the track number , and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number wher e the CD is being loaded. After the radio displays “ load ” insert the CD into the player .
FF/TUNE/R W Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner . Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play .
Program T ype Radio Display Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Mu.
By pressing the SCAN button when the PTY icon is displayed, the radio will stop at every PTY station on the band and list each corresponding program type in the radio display . T ime Press the TIME button to change the display from elapsed CD playing time to time of day .
variety of destinations and routes. Refer to your “ Navi- gation User ’ s Manual ” for detailed operating instruc- tions. NOTE: If your vehicle is not equipped with the CD Changer option, you will not be able to use the Naviga- tion system and the CD Player simultaneously .
As preventive maintenance, clean the head about every 30 hours of use. If you wait until the head becomes very dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple WET cleaning cassette. CD/DVD DISC MAINTENANCE T o keep the CD/DVD discs in good condition, take the following precautions: 1.
CLIMA TE CONTROLS Air Conditioning The Air Conditioning System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle.
Fan speeds to the right of OFF are for heater or ventila- tion operation. The fan speed increases as you move the control to the right from the OFF position. Mode Control (Air Direction) The mode control allows you to choose fr om several pat- terns of air distribution.
Mix Air is directed through the floor , defrost and side window demist outlets. This setting works best in cold or snowy conditions that requir e extra heat at the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
T emperature Control Use this control to regulate the temperature of the air in- side the passenger compart- ment. The blue area of the scale indicates cooler tem- peratures while the red ar ea indicates warmer tempera- tures.
In cold or damp weather , the use of the Recir culate position will cause windows to fog on the inside because of moisture build up inside the vehicle.
Operating Tips 174 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
W indow Fogging V ehicle side windows tend to fog on the inside in mild rainy or humid weather . T o clear the windows, use the A/C, P ANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recir culate without A/C for long periods as fogging may occur .
Side W indow Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the ar ea of the windows thr ough which you view the outside mirrors.
CAUTION! T o avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window .
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 1 8 2 ▫ Automatic T ransaxle ................... 1 8 2 ▫ Manual T ransaxle ..................... 1 8 2 ▫ Normal Starting ...................... 1 8 2 ▫ Extremely Cold W eather (Below ⫺ 20 ° F Or ⫺ 29 ° C ) .
▫ AutoStick General Information ............ 1 9 0 䡵 Manual T ransaxle Operation ............... 1 9 1 ▫ 2.4 Liter T urbo — If Equipped ............. 1 9 3 ▫ Recommended Shift Speeds .............. 1 9 4 ▫ Downshifting ....................
䡵 T ire Rotation Recommendations ............ 2 2 0 䡵 Fuel Requirements ...................... 2 2 1 ▫ 2.4L Standard Engine And 2.4L Standard T urbo Engine ............................. 2 2 1 ▫ 2.4L High Output T urbo Engine ........... 2 2 1 ▫ Reformulated Gasoline .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 15 seconds, turn the ignition switch to the “ OFF ” position, wait 10 to 15 seconds, then repeat the normal starting procedur e.
W ARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury . CAUTION! T o prevent damage to the starter , do not crank the engine for more than 15 seconds at a time.
TURBOCHARGER ⴖ COOL DOWN ⴖ CHAR T Driving Conditions Idle T ime (in minutes) Before Shut Down Normal Driving Not requir ed. Aggressive Driving or Heavily Loaded 3 T railer T ow 5 AUTOMA TIC TRANSA.
W ARNING! It is dangerous to shift the selector lever out of “ P ” or “ N ” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something.
Reset Mode The transaxle is monitored electronically for abnormal conditions. If a condition is detected that could cause damage, the transaxle shifts automatically into second gear . The transaxle remains in second gear despite the forward gear selected.
W ARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake.
“ R ” Reverse Shift into this range only after the vehicle has come to a complete stop. “ N ” Neutral Engine may be started in this range. “ D ” Overdrive This range should be used for most city and highway driving. It provides smoothest up shifts and down shifts and best fuel economy .
AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transmission that offers manual gear shifting capability to pr ovide you with more control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance.
• Downshifts from third to second gear above 74 mph (1 19 km/h) and from second to first gear above 41 mph (66 km/h) will be ignored. • Y ou can start out in first, second, or thir d gear . Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. Use each gear in numerical order - do not skip a gear . Be sure the transaxle is in FIRST gear , (not THIRD), when starting from a standing position.
2.4 Liter T urbo — If Equipped The neutral position of the shift lever is located between THIRD and FOUR TH gear . This is the position the shifter lever will return to automatically when neutral is se- lected.
Recommended Shift Speeds T o use your manual transaxle for optimal fuel economy , it should be upshifted as listed in table 1. T ABLE 1-MANUAL TRANSAXLE NORMAL AC- CELERA TION AND CRUISE SHIFT SPEEDS IN mph (km/h) EN- GINE SIZE MODE 1t o2 2t o3 3t o4 4t o5 2.
CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch. T o maintain a safe speed and prolong brake life, shift down to 2nd or 1st when descending a steep grade.
NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park.
W ARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector . Don ’ t leave the keys in the ignition.
If either of the two hydraulic systems lose normal capa- bility , the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force requir ed to slow or stop.
W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
TRACTION CONTROL — IF EQUIPPED The T raction Contr ol System will improve acceleration and steering on slippery surfaces by reducing tire spin. The system reduces wheel slip and maintains traction at the driving (front) wheels by engaing the brake on the wheel that is losing traction.
The system is always in the “ ON ” mode unless: • The TRAC OFF switch has been used to turn the system off; • There is a Anti-Lock Brake System malfunction; • There is a T raction Control System malfunction; • The system has been automatically deactivated to prevent damage to the brake system due to over heated brake temperatures.
NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “ P ” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry . H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and Tire Pressure T ire Placard Location NOTE: The proper cold tire inflation pressur e for pas- senger cars is listed on either the face of the driver ’ s door or the driver ’ s side “ B ” pillar .
T ire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
T o determine the maximum loading conditions of your vehicle, locate the statement “ The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.
ST ARTING AND OPERA TING 209 5 I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, af fect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy — Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tir e replacement. Underinflation also increases tir e rolling resistance and results in higher fuel consumption.
The pressure should be checked and adjusted as well as inspecting for signs of tir e wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressur e. Do not make a visual judgement when determining pr oper inflation.
T ire pressur e may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressur e build up or your tire pressure will be too low . T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits.
Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
W ARNING! The limited use spare tires are for emergency use only . Installation of this limited use spare tire af fects vehicle handling. W ith this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly .
These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or mor e adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a r esult of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear . TIRE CHAINS Due to limited clearance, tire chains are not recom- mended.
Tire Rotation Recommendations T ires on the front and rear axles of vehicles operate at differ ent loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns.
FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard T urbo Engine Y our vehicle is designed to meet all emis- sion regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended.
Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the W orld W ide Fuel Charter , WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber . Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT .
• An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may requir e immediate service.
• Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repair ed promptly .
CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on. CAUTION! T o avoid fuel spillage and overfilling, do not “ top off ” the fuel tank after filling. NOTE: When the fuel nozzle “ clicks ” or shuts off, the fuel tank is full.
W ARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. Y ou could be burned. Always place gas containers on the ground while filling. VEHICLE LOADING V ehicle Loading Capacities Front Seat Occupants ..
W arranty T o maintain warranty coverage, follow the requirements and recommendations in this manual concerning ve- hicles used for trailer towing. However the following conditions must be met: • The maximum frontal area of the trailer cannot exceed 20 square feet (1.
• Whenever you pull a trailer , regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety . • The automatic transaxle fluid and filter should be changed if you REGULARL Y tow a trailer for more than 45 minutes of continuous operation.
I n f o r m a t i o n P r o v i d e d b y :.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 2 3 2 䡵 If Y our Engine Overheats ................. 2 3 3 䡵 Jacking And T ire Changing ................ 2 3 5 ▫ Jack Location ........................ 2 3 5 ▫ Spare T ire Stowage .
HAZARD W ARNING FLASHER The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash. Depress the switch again to turn Hazard W arning Flashers off.
IF YOUR ENGINE OVERHEA TS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transaxle in neutral, but do not increase engine idle speed.
CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “ H ” , pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
JACKING AND TIRE CHANGING W ARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism. T o re- move or stow the compact spare, use the jack handle to rotate the “ spare tire drive ” nut. The nut is located under the rear scuff plate at the right rear of the cargo area, just inside the deck lid opening.
Spare T ire Removal Lift up the plastic cover on the scuff plate and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire.
Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. T o reinstall the cap, make sure it is properly lined up before pushing it on to the wheel.
Do not raise the vehicle until you are sur e the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tir e.
100 ft. lbs (135 N · m). If you doubt that you have tightened the nuts correctly , have them checked with a torque wrench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free. Stow the lug wrench, replaced tire, and jack.
W ARNING! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- axle cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
W ARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don ’ t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water .
8. When removing the jumper cables, reverse the se- quence exactly . Be careful of the moving belts and fan. DRIVING ON SLIPPER Y SURF ACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left.
2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop.
CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55km/h).
All T ransaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in the LOCK or ACCESSOR Y positions. Do not attempt to use sling type equipment when towing. When securing vehicle to flat bed truck, do not attach to front or rear suspension components.
CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery , etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bleeder screw , which is found in the trunk under the convertible top storage area.
5. Pull down and rotate the handle counterclockwise to engage the latches. 6. Raise the handle into the stowed position. 7. Close the convertible top motor bleeder screw by turning the screw clockwise until it stops.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 2.4L T urbo Engine Compartment ............ 2 5 2 䡵 2.4L Engine Compartment ................ 2 5 3 䡵 Onboard Diagnostic System — O B D I I ........ 2 5 4 䡵 Emissions Inspection And Maintenance Programs ..
▫ Air Conditioner Maintenance ............. 2 6 7 ▫ Power Steering — Fluid Check ............ 2 6 8 ▫ Front Suspension Ball Joints .............. 2 6 8 ▫ Body Lubrication ..................... 2 6 9 ▫ W indshield W iper Blades ............
䡵 Bulb Replacement ...................... 2 9 9 ▫ Headlight Bulb Replacement ............. 2 9 9 ▫ Front Park/T urn Signal/Side Marker Lights . . 300 ▫ Front Fog Lights — If Equipped ........... 3 0 0 ▫ T ail/Stop, And Rear T urn Signal Lights .
2.4L TURBO ENGINE COMP ARTMENT 252 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
2.4L ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 253 7 I n f o r m a t i o n P r o v i d e d b y :.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboar d diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle ’ s emissions control system.
a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle ’ s OBD system is not ready and you should not proceed to the I/M station. b.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level gr ound, will improve the accuracy of the oil level readings.
• Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather , above 90 ° F (32 ° C). • T railer towing. • T axi, Police or delivery service (commercial service).
Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufactur er only recommends engine oils that are API certified and meet the requir ements of DaimlerChrysler Material Standard MS-6395.
Materials Added T o Engine Oils The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it ’ s performance may be impaired by supplemental ad- ditives.
Special tools ar e required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control.
CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly .
T o minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected for prolonged period.
NOTE: For vehicles with a T urbo engine, a small amount of oil accumulation in the air cleaner box is normal. The amount will depend on driving style. The air cleaner box should be cleaned out and a new make-up- air filter element should be installed during the normal air filter maintenance procedur e.
W ARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don ’ t allow battery fluid to contact your eyes, skin or clothing. Don ’ t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water .
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test.
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product.
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, deck lid and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear .
2. Push the r elease tab shown in the illustration and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a pr operly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
W ith the engine at normal operating temperature (but not running), check the cooling system pressur e cap for proper vacuum sealing by draining a small amount of coolant from the radiator drain cock. If the cap is sealing properly , the engine coolant (antifreeze) will begin to drain from the coolant recovery bottle.
CAUTION! Mixing of coolants other than specified engine cool- ants, may result in engine damage that may not be covered under the new vehicle warranty , and de- creased corrosion protection. If a non-HOA T coolant is introduced into the cooling system in an emer- gency , it should be replaced with the specified coolant as soon as possible.
Cooling System Pressure Cap The cap must be fully tightened to pr event loss of coolant, and to insure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
service attendant of this. As long as the engine operating temperature is satisfactory , the coolant recovery bottle need only be checked once a month. When additional coolant is needed to maintain the proper level, it should be added to the coolant recovery bottle.
• Do not change the thermostat for summer or winter operation. If r eplacement is ever necessary , install ONL Y the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.
Brake System In order to assure brake system performance, all brake system components should be inspected periodically . Suggested service intervals can be found in the Mainte- nance Section. W ARNING! Riding the brakes can lead to brake failure and possibly an accident.
NOTE: Inspection of brake hoses should be done when- ever the brake system is serviced and at every engine oil change. W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately .
Use only manufacturers recommended brake fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. W ARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking.
CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180 ° F (82 ° C), which is the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortable held between the finger tips.
CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. T o prevent dirt and water from entering the transaxle after checking or replen- ishing fluid, make certain that the dipstick cap is seated properly .
Manual T ransaxle Lubricant Selection Use only manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 3/16 ” (4.
The following maintenance r ecommendations will enable you to obtain maximum benefit fr om the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose of f the undercarriage at least once a month.
CAUTION! If your vehicle is equipped with flame or woodgrain graphics, it is recommended that special care be taken when using hand-held pressure washers to clean your vehicle. The pressure of these hand-held car wash wands can vary greatly and could possibly cause damage to the surface of the graphic.
CAUTION! Many wheel cleaners contain acids that may harm the wheel surface. NOTE: Replacement costs for components damaged as a result of not following the recommended cleaning practices are considered the responsibility of the cus- tomer . Interior Care Use Mopar Fabric Cleaner to clean fabric upholstery and carpeting.
Cleaning Headlights Y our vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefor e differ ent lens cleaning procedures must be followed.
2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water .
a soft, natural bristle scrub brush, and a mild soap solution such as liquid dish washing soap. Do not use detergent. CAUTION! Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic sol- vents, petroleum distillates or plasticizers.
Cloth T op Protection For appearance purposes, you may wish to protect your T willfast ™ (cloth) top periodically . A fabric protectant such as Scotchguard 威 is suggested. The top should be clean and dry before application of the protectant. CAUTION! A void getting Scotchguard 威 on the surrounding weather strips, moldings, paint, or glass.
Power Distribution Center MAINT AINING YOUR VEHICLE 293 7 I n f o r m a t i o n P r o v i d e d b y :.
FUSE Amp/Color Items Fused 1 30 Amp/Pink Ignition Start 2 40 Amp/ Green Anti-Lock Brake (ABS) Pump 3 40 Amp/ Green Ignition Run 4 30 Amp/Blue Heated Seats 5 40 Amp/ Green Radiator Fan (Low Speed T urb.
20 20 Amp/ Y ellow Power Outlets 21 Spare 22 20 Amp/ Y ellow Fog Lamps (Export Only) Interior Fuses The fuse access panel is on the left side of the instrument panel next to the steering column. T o remove the panel, pull it out, as shown. A label identifying the components and circuits is located on the inside of the cover .
FUSE Amp/Color Items Fused 1 25 Amp/ Natural Headlamp Switch 2 15 Amp/Lt. Blue Park Lamps 3 20 Amp/ Y ellow RKE/Door Locks 4 20 Amp/ Y ellow Power Height Adjust 5 10 Amp/Red Airbag Run Only 6 10 Amp/Red B/U Electric Back Light (EBL) NEU SAF 7 25 Amp/ Natural HV AC Blower 8 15 Amp/Lt.
CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow , it shows a problem in the circuit that must be corrected.
Rear Cargo ............................ T906 Seat Belt Indicator ....................... L E D Security Alarm Indicator ................... L E D Malfunction Indicator Light ................ L E D T emperature Indicator .................... L E D T rac (Active) Indicator .
BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening.
Front Park/T urn Signal/Side Marker Lights 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. Front Fog Lights — If Equipped 1.
2. T wist the bulb socket 1/4 turn to remove it from the housing. 3. Pull the bulb out of the socket and replace. Back Up Light Bulb 1. Remove the screws attaching the back up light to the rear fascia and remove the housing. 2. Remove the socket from the housing.
FLUIDS AND CAP ACITIES U.S. Metric Fuel (Approximate) 15 Gallons 56.7 Liters Engine Oil-W ith Filter 2.4 Liter Engines (Use API Certified SAE 5W -30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meet- ing DaimlerChrysler Material Standard MS-6395.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil Use API Certified SAE 5W -30 Engine Oil.
Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Fluid. Mopar 威 A TF+4 Automatic T ransmission Fluid. Manual T ransmission Fluid. Mopar 威 A TF+4 Automatic T ransmission Fluid. Brake Master Cylinder Mopar 威 DOT 3, SAE J1703 should be used.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 0 6 䡵 Maintenance Schedule ................... 3 0 6 ▫ Schedule “ B ”— All Engines .............. 3 0 9 ▫ Schedule “ A ”— Non T urbo ............... 3 1 9 ▫ Schedule “ A ”— T urbo .
EMISSION CONTROL SYSTEM MAINTENANCE The “ Scheduled ” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system.
• T axi, police, or delivery service (commercial ser- vice). † 〫 • Off-r oad or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut of f. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.
SCHEDULE “ B ”— ALL ENGINES Follow schedule “ B ”— All Engines if you usually operate your vehicle under one or more of the following condi- tions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫 .
NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (164,000 km) or 60 months, whichever comes first, and follow schedule “ B — All Engines ” of the ⬙ Maintenance Sched- ules ⬙ section of this manual.
Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace as necessary .
Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X X Replace the engine air cleaner filter .
Miles 39,000 42,000 45,000 48,000 51,000 54,000 ( Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X Change the brake fluid.
Miles 57,000 60,000 63,000 66,000 69,000 72,000 ( Kilometers) (91 000) (96 000) (101 000) (106 000) (1 11 000) (1 15 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X X Replace the engine air cleaner filter .
Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (120 000) (125 000) (130 000) (135 000) (130 000) (144 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X Inspect the engine air cleaner filter and replace as necessary .
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (150 000) (154 000) (159 000) (164 000) (168 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Rotate tires. X X Inspect the brake linings. X Change the brake fluid.
Miles 108,000 1 1 1,000 114,000 117,000 120,000 (Kilometers) (173 000) (178 000) (183 000) (188 000) (193 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Rotate tires. X X X Inspect the brake linings. X Replace the engine air cleaner filter .
* This maintenance is r ecommended by the manufacturer to the owner but is not requir ed to maintain the emis- sions warranty . ‡ This maintenance is not r equired if previously r eplaced. † This maintenance is required only for police, taxi, limousine type operation, or trailer towing.
SCHEDULE “ A ”— NON TURBO Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers ) (10 000) (19 000) (29 000) (38 000) (48 000) (58 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Rotate tires. X XXXXX Inspect the brake linings.
Miles 42,000 48,000 54,000 60,000 66,000 (Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) [Months] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . XXXXX Rotate tires. XXXXX Inspect the brake linings. X Replace the engine air cleaner filter .
Miles 72,000 78,000 84,000 90,000 96,000 102,000 (Kilometers) (1 15 000) (125 000) (134 000) (144 000) (154 000) (164 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X X X X X X Rotate tires. X X X X X X Inspect the brake linings.
Miles 108,000 1 14,000 120,000 (Kilometers) (173 000) (182 000) (192 000) [Months] [108] [1 14] [120] Change engine oil and engine oil filter . X X X Rotate tires. X X X Inspect the PCV valve and replace if necessary . * ‡ X Replace the air cleaner filter .
SCHEDULE “ A ”— TURBO Miles 5,000 10,000 15,000 20,000 25,000 30,000 (Kilometers) (8 000) (16 000) (24 000) (32 000) (40 000) (48 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Rotate tires. X XXXXX Inspect the brake linings.
Miles 35,000 40,000 45,000 50,000 55,000 (Kilometers) (56 000) (64 000) (72 000) (80 000) (88 000) [Months] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . XXXXX Rotate tires. XXXXX Inspect the brake linings. X Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles.
Miles 60,000 65,000 70,000 75,000 80,000 85,000 (Kilometers) (96 000) (104 000) (1 12 000) (120 000) (128 000) (136 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X XXXX X Rotate tires. X XXXX X Inspect the brake linings.
Miles 90,000 95,000 100,000 105,000 (Kilometers) (144 000) (156 000) (160 000) (168 000) [Months] [108] [1 14] [120] [126] Change engine oil and engine oil filter . X X X X Rotate tires. X X X X Inspect the brake linings. X Replace the engine air cleaner filter .
Miles 1 10,000 1 15,000 120,000 (Kilometers) (177 000) (185 000) (193 000) [Month] [132] [138] [144] Change engine oil and engine oil filter . X X X Rotate tires. X X X Inspect the PCV V alve and replace if necessary . * X Replace the engine air cleaner filter .
I n f o r m a t i o n P r o v i d e d b y :.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 3 3 0 ▫ Prepar e For The Appointment ............ 3 3 0 ▫ Prepar e A List ........................ 3 3 0 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you ’ re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional char ges with the service manager .
IF YOU NEED ASSIST ANCE The manufacturer and its dealers are vitally interested in your satisfaction. W e want you to be happy with our products and services. W arranty service must be done by an authorized Chrysler , Dodge, or Jeep dealer . W e strongly recommend that you take your vehicle to you selling dealer .
DaimlerChrysler Motors Corporation Customer Center P .O. Box 21 – 8004 Auburn Hills, MI 48321 – 8004 Phone: (800) 992-1997 DaimlerChrysler Canada Inc. Customer Center P .O. Box 1621 W indsor , Ontario N9A 4H6 Phone — (800) 465 – 2001 In Mexico contact: A v .
contract, call the manufacturer ’ s Service Contract Na- tional Customer Hotline at 1-800-521-9922. The manufacturer will not stand behind any service contract that is not the manufactur er ’ s Service Contract. It is not responsible for any service contract other than the manufacturer ’ s Service Contract.
U.S. ONL Y 334 IF YOU NEED CONSUMER ASSIST ANCE I n f o r m a t i o n P r o v i d e d b y :.
MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best.
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Fr ee at 1 – 800 – 890 – 4038 (U.S.) or 1 – 800 – 387 – 1 143 (Canada) Or V isit us on the W orld W ide W eb at: www .techauthority .
W ARNING! The traction grade is based on braking (straight- ahead) traction tests and does not include cornering (turning) performance. T emperature Grades The temperature grades are A (highest), B, a.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
ABS (Anti-Lock Brake) System .............. 1 9 8 Adding Engine Coolant (Antifreeze) .......... 2 7 4 Adding Fuel ........................... 2 2 5 Adding W asher Fluid ..................... 1 0 0 Additives, Fuel ......................... 2 2 3 Air Cleaner , Engine (Engine Air Cleaner Filter) .
Back-Up Lights ......................... 3 0 1 Ball Joints ............................. 2 6 8 Battery ............................... 2 6 5 Keyless T ransmitter Replacement ............ 2 4 Belts, Drive ............................ 2 6 1 Belts, Engine .
Cellular Phone .......................... 1 6 8 Center High Mounted Stop Light ............ 3 0 1 Central Door Locks ....................... 2 0 Chains, T ire ............................ 2 1 9 Changing A Flat T ire ..................... 2 3 5 Chart, T ire Sizing .
Radiator Cap ......................... 2 7 5 Selection of Coolant .................... 2 7 3 Corrosion Protection ..................... 2 8 4 Crankcase Emission Control System .......... 2 6 4 Cruise Light ........................... 1 3 2 Cup Holder .
Emission Control System Maintenance ...... 255,306 Engine ............................ 252,253 Break-In Recommendations ................ 5 6 Checking Oil Level ..................... 2 5 7 Exhaust Gas Caution .................... 2 2 4 Fuel Requirements .
Fuel .............................. 221,303 Adding ............................. 2 2 5 Additives ............................ 2 2 3 Capacity ............................ 3 0 2 Clean Air ............................ 2 2 2 Filler Cap ...................
High Beam ......................... 97,129 High Beam/Low Beam Select Switch ......... 9 7 Passing .............................. 9 7 Switch ............................... 9 6 Heated Seats ............................ 8 6 Homelink T ransmitter .......
Knee Bolster .......................... 44,46 Lane Change and T urn Signals .............. 1 2 8 Lap/Shoulder Belts ....................... 3 1 Latches Hood ............................... 9 3 Lead Free Gasoline ...................... 2 2 1 Light Bulbs .
Loading V ehicle ......................... 2 2 7 T i r e s ............................... 2 0 6 Locks Central .............................. 2 0 Door ................................ 1 8 Power Door ........................... 1 9 Steering Wheel .....
New V ehicle Break-In Period ................ 5 6 Occupant Restraints ....................... 3 0 Octane Rating, Gasoline ................... 2 2 1 Odometer ............................. 1 3 1 T r i p ............................. 131,134 Oil, Engine .
Steering .......................... 199,268 Steering, Checking ..................... 2 6 8 W indows ............................. 2 8 Power Steering Fluid ..................... 3 0 4 Pregnant W omen and Seat Belts .............. 3 9 Pretensioners Seat Belts .
Seat Belts .............................. 3 0 And Pregnant W omen ................... 3 9 Child Restraint ......................... 4 9 Cleaning ............................ 2 9 0 Front Seat ............................ 3 1 Pretensioners .............
Starting ............................... 1 8 2 Automatic T ransmission ................. 1 8 2 Engine Fails to Start .................... 1 8 3 Manual T ransmission ................... 1 8 2 Starting Procedur es ...................... 1 8 2 Steering Power .
Quality Grading ....................... 3 3 7 Radial .............................. 2 1 4 Replacement ......................... 2 1 7 Rotation ............................. 2 2 0 Safety ........................... 201,210 Sizes .......................
Understanding Y our Instrument Panel ......... 1 2 3 Uniform T ire Quality Grades ................ 3 3 7 Universal T ransmitter ..................... 1 0 6 Unleaded Gasoline ....................... 2 2 1 Untwisting Procedur e, Seat Belt ..............
NOTES I n f o r m a t i o n P r o v i d e d b y :.
NOTES I n f o r m a t i o n P r o v i d e d b y :.
NOTES I n f o r m a t i o n P r o v i d e d b y :.
NOTES I n f o r m a t i o n P r o v i d e d b y :.
NOTES I n f o r m a t i o n P r o v i d e d b y :.
NOTES I n f o r m a t i o n P r o v i d e d b y :.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Chrysler PT Cruiser convertible (2005) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Chrysler PT Cruiser convertible (2005) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Chrysler PT Cruiser convertible (2005), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Chrysler PT Cruiser convertible (2005) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Chrysler PT Cruiser convertible (2005), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Chrysler PT Cruiser convertible (2005).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Chrysler PT Cruiser convertible (2005). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Chrysler PT Cruiser convertible (2005) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
