Manuel d'utilisation / d'entretien du produit PT Cruiser (2006) du fabricant Chrysler
Aller à la page of 464
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number ............... 6 䡵 V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1 I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
I n f o r m a t i o n P r o v i d e d b y :.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 3 ▫ Ignition Key Removal ................... 1 3 ▫ Locking Doors W ith The Key .............. 1 4 ▫ Key-In-Ignition Reminder ...............
▫ T o Unlock The Doors And Liftgate .......... 2 5 ▫ T o Lock The Doors And Liftgate (If Equipped W ith Power Options) .......... 2 6 ▫ Using The Panic Alarm .................. 2 6 ▫ T o T urn Off “Flash Lights W ith Lock” ........ 2 7 ▫ Programming Additional T ransmitters .
䡵 Emergency Deck Lid Release Latch (Convertible) ........................... 4 1 䡵 Power W indows ........................ 4 2 ▫ Auto Down Feature .................... 4 3 ▫ Rear W indow Switches .................. 4 4 ▫ W ind Buffeting ....
䡵 Safety T ips ........................... 1 1 4 ▫ Exhaust Gas ......................... 1 1 4 ▫ Safety Checks Y ou Should Make Inside The V e h i c l e ............................. 1 1 4 ▫ Periodic Safety Checks Y ou Should Make Outside The V ehicle .
A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer .
NOTE: If you try to r emove the key before you place the lever in P ARK, the key may become trapped temporarily in the ignition cylinder . If this occurs, r otate the key to the right slightly , then remove the key as described.
Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key . NOTE: W ith the driver’s door open, and the key in the ignition, both the power door locks and Remote Keyless Entry (RKE) will not function.
NOTE: • The Sentry Key Immobilizer System is not compatible with r emote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
Sentry Key Programming Y ou can program new keys to the system if you have two valid sentry keys by performing the following pr ocedure: 1. Cut the additional Sentry Key T ransponder blank(s) to match the ignition switch lock cylinder key code.
STEERING WHEEL LOCK — IF EQUIPPED Y our vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key . If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
W ARNING! For personal security , and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. W ARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Power Door Locks A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. Automatic Door Locks—If Equipped The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1.
1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between LOCK and ON and back to LOCK 4 times ending up in the LOCK position. 3. Depr ess the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programming.
1. The Auto Unlock feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or P ARK. 4. The driver door is opened. 5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h).
NOTE: Use the Auto Door Locks and Auto Unlock features in accordance with local laws. “Child-Protection” Door Lock System (Rear Doors) — If Equipped T o provide a safer environment for children riding in the rear seat, the rear doors have the “child-protection” door lock system.
W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emer gency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
NOTE: The line of transmission must not be blocked with metal objects. T o unlock the doors and liftgate: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate.
NOTE: Pr essing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5.
The panic alarm will stay on for 3 minutes unless you turn it off by pressing the P ANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater . NOTE: When you turn off the panic alarm by pressing the P ANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system.
NOTE: When entering program mode using that fob, all other programmed fobs will be erased and you will have to repr ogram them for your vehicle. Use the Following procedur e to program additional key fobs if the vehicle is not equipped with Sentry Key: 1.
14. Y our vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normally . NOTE: If you do not have a programmed transmitter , contact your dealer for details. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada.
Battery Replacement The recommended replacement battery is CR2032. 1. If the key fob is equipped with a screw , remove the screw . W ith the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal.
REMOTE KEYLESS ENTR Y (CONVERTIBLE) This system allows you to lock or unlock the doors or open the deck lid from distances of 23–50 feet (7–15 meters) using a transmitter . Y ou don’t have to point the transmitter at the vehicle to activate the system.
The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedur e: 1. Pr ess and hold the LOCK button on a programmed key fob. 2. Continue to hold the LOCK button at least 4 seconds, but not longer than 10 seconds, then press and hold the UNLOCK button.
The “Sound Horn On Lock” and “Flash Lamps W ith Lock” feature can be reactivated by repeating this proce- dure. T o Unlatch the Deck Lid Press the “Rear Release” button twice to unlatch the deck lid. Panic Alarm The panic mode flashes the park lights, and sounds the horn for about 3 minutes or until the alarm is turned off.
3. T est the flash lamps with LOCK feature while outside of the vehicle, by pressing the LOCK button on the key fob with the ignition in the LOCK position, and the key removed. NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm.
General Information This transmitter complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undes- ired operation.
2. Remove and replace the batteries. A void touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch the battery , clean it with rubbing alcohol. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation.
T o disarm the system: Unlock a front door/liftgate using the Keyless Entry T ransmitter . Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm.
LIFTGA TE (SEDAN) NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate (if equipped). Rotate the key and pull the liftgate up. T o unlock the liftgate, insert the key into the lock and turn to the right.
W ARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. Y ou and your passengers could be injured by these fumes.
Gas props support the deck lid in the open position. However , because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the deck lid in cold weather .
seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back latching mechanism. Once unlatched the seat back can be pushed forward to gain access into the interior of the vehicle. NOTE: Make sure that the elastic loop is ar ound the emergency release handle at all times.
As a security measure, an emergency deck lid release lever is built into the deck lid latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in- the-dark lever attached to the deck lid latching mecha- nism.
The convertible has an ⬙ All windows up ⬙ and ⬙ All windows down, ⬙ switch located between the window switches instead of the lock switch. W ARNING! Never leave children in a vehicle, with the keys in the ignition switch.
Rear Window Switches There are also rear passenger window switches (sedan only) located at the rear of the center console. Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears.
adult-size seat belts, your seat belts or the LA TCH feature also, can be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.
The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
4. Position the lap belt across your thighs, below your abdomen. T o r emove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
6. T o release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
W ARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the rear seat back is in the fully upright and locked position when occu- pied.
Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate.
3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing.
Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced W arning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt.
4. T urn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. The Enhanced W arning System (BeltAlert) can be reacti- vated by repeating this procedure.
NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that ar e based on collision severity and occupant size.
W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protec- tive covers for the airbag cushions are designed to open only when the airbags are inflating.
empty or is occupied by someone that is classified in the “child ⬙ category . This could be a child, a teenager , or even a small adult. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat.
5. If the airbag system in this vehicle needs to be modified to accomodate a disabled person, contact the Customer Center . Phone numbers are provided under ⬙ If Y ou Need Assistance ⬙ in Section 9 of this manual. W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
The front airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If equipped) • Airbag W arning Light • Driver Airbag • Passenger Airbag.
The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the ST ART or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters.
• The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers push- ing down on the seat will also be sensed.
front passenger seat. In this case, the air bag is ready to be inflated if a collision requiring an airbag occurs. For all other occupants, the P AD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate.
or instrument panel), the weight sensors in the seat may not properly classify the occupant. Objects lodged under the seat or between the seat and the center console can prevent the occupant’s weight from being measur ed properly and may result in the occupant being improp- erly classified.
may be possible based on collision severity and occu- pant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds.
The ORC Module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the ST AR T or ON positions. These include all of the items previously mentioned. In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas.
The following requir ements must be strictly adhered to: • Do not modify the front passenger seat assembly or components in any way . • Do not modify the front seat center console or center position seat in any way . • Do not use prior or future model year seat covers not designated for the specific model being repair ed.
If A Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-severe col- lision, to help r estrain the driver and fr ont passenger , and then immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
W ARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly , replaced by an authorized dealer as soon as possible. Also, have the Occupant Classification System serviced as well.
Airbag Light Y ou will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately .
identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver , vehicle, or crash, will be treated confidentially .
Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces requir e that small childr en ride in proper r estraint systems. This is the law , and you can be prosecuted for ignoring it.
• Safety experts recommend that children ride rearwar d-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used rearward-facing: infant carriers and ⬙ convertible ⬙ child seats.
are held in the vehicle by the lap/shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.) NOTE: For additional information refer to www .nhtsa.dot.gov or www .seatcheck.org. W ARNING! • Improper installation can lead to failure of an infant or child restraint.
restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt.
from the r etractor . Allow the belt to r eturn into the retractor , pulling on the excess webbing to tighten the lap portion about the child restraint. Follow the instructions of the child restraint manufacture. NOTE: T o reset this feature you must let all of the belt webbing return into the retractor .
Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it.
Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. NOTE: If your child restraint seat is not LA TCH com- patible, install the restraint using the vehicle seat belts.
Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. OCCUP ANT RESTRAINTS (CONVERTIBLE) Some of the most important safety featur es in your vehicle are the restraint systems.
ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All the seats in your vehicle are equipped with Lap/ Shoulder Belts.
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. • W earing your belt in the wrong place could make your injuries in a collision much worse.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
4. Position the lap belt across your thighs, below your abdomen. T o r emove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
6. T o release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate.
3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing.
Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced W arning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt.
4. T urn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. The Enhanced W arning System (BeltAlert) can be reacti- vated by repeating this procedure.
NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that ar e based on collision severity and occupant size.
W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protec- tive covers for the airbag cushions are designed to open only when the airbags are inflating.
empty or is occupied by someone that is classified in the “child” category . This could be a child, a teenager , or even a small adult. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat.
5. If the airbag system in this vehicle needs to be modified to accomodate a disabled person, contact the Customer Center . Phone numbers are provided under ⴖ If Y ou Need Assistance ⴖ in Section 9 of this manual. W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
The front airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If Equipped) • Airbag W arning Light • Driver Airbag • Passenger Airbag.
The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the ST ART or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters.
• The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers push- ing down on the seat will also be sensed.
child restraint or booster seats, most children that can properly wear the vehicle’s seat belt, and when an adult passenger is properly seated in the front passen- ger seat. In this case, the air bag is ready to be inflated if a collision requiring an airbag occurs.
or instrument panel), the weight sensors in the seat may not properly classify the occupant. Objects lodged under the seat or between the seat and the center console can prevent the occupant’s weight from being measur ed properly and may result in the occupant being improp- erly classified.
may be possible based on collision severity and occu- pant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds.
In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas. The inflating side airbag exits thr ough the seat seam into the space between the occupant and the door .
• Do not modify the front seat center console or center position seat in any way . • Do not use prior or future model year seat covers not designated for the specific model being repair ed. Al- ways use the corr ect seat cover specified for the vehicle.
NOTE: A frontal collision that is not sever e enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you.
data gathered during a complete accident investigation, the electronic data may be used by DaimlerChrysler and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
• Diagnostic tr ouble code(s) and warning lamp status for electronically-contr olled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • ⬙ Ti m e ⬙ of ai.
W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured.
• Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. W e also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it.
belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again.
Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it.
Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. NOTE: If your child restraint seat is not LA TCH com- patible, install the restraint using the vehicle seat belts.
• Check belt fit periodically . A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty . SAFETY TIPS Exhaust Gas W ARNING! Exhaust gases can injure or kill.
Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent r etractor , torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt.
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Convertible T op Operation ................ 1 2 1 ▫ T o Lower The T op ..................... 1 2 1 ▫ T o R a i s e T h e T o p ..................... 1 2 4 ▫ Convertible T op Boot Cover Installation–If Equipped .
▫ UConnect™ System Features ............. 1 4 7 ▫ Advanced Phone Connectivity ............ 1 5 2 ▫ Things Y ou Should Know About Y our UConnect™ System .................... 1 5 4 䡵 Seats ................................ 1 5 9 ▫ Front Seat Adjustment .
▫ Daytime Running Lights (DRL)(Canada Only) . 182 ▫ Lights-On Reminder ................... 1 8 2 ▫ Fog Lights — If Equipped ............... 1 8 3 ▫ T urn Signals ......................... 1 8 3 ▫ Highbeam/Lowbeam Select Switch ......... 1 8 3 ▫ Passing Light .
▫ Canadian Programming/Gate Programming . . 197 ▫ Operation ........................... 1 9 8 ▫ Reprogramming A Single Button .......... 1 9 8 ▫ Security ............................ 1 9 8 䡵 Power Sunroof — If Equipped ............. 1 9 9 ▫ Express Open Feature .
CONVERTIBLE TOP OPERA TION W ARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision.
CAUTION! T o fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position (automatic transaxle) or in the Neutral position (manual transaxle) before lowering or raising the top. CAUTION! Do not operate the convertible top with ice or snow build-up on the top.
3. Press the Power T op Switch to lower the top just enough to disengage the top pins from the header , turn the handle counterclockwise and raise the handle to the stowed position. NOTE: The Power T op Switch has two detent positions for lowering the convertible top.
4. Continue pressing the Power T op Switch until the convertible top is lowered completely . 5. Install the Convertible T op Boot Cover , if equipped. Refer to Convertible T op Boot Cover Installation–If Equipped, in this section.
1. Remove the convertible top boot cover , if equipped. Refer to Convertible T op Boot Cover Removal and Stor- age, in this section. 2. T urn the ignition to the ON position. 3. Press the Power T op Switch to raise the top. Before the top reaches the windshield, open the latch handle and turn the handle clockwise to open the latches.
CAUTION! Car top carriers, ski racks, etc., should not be at- tached to the convertible top mechanism as they will damage the top. Do not place objects on the convert- ible top, in the top well or on the sport bar . Damage to the convertible top may occur .
2. Install the rear edge of the boot, first tucking the rear edge of the boot under the rear and both sides of the rails. Boot Laying Across Convertible T op UNDERST ANDING THE FEA TURES OF YOUR VEHIC.
3. Pull the right and left boot arms forward and engage both boot arm snaps. Make sure both snaps are fully engaged. T ucking Boot Under Rail Engaging Boot Arm Snaps 128 UNDERST ANDING THE FEA TURES O.
4. Engage the boot center section retainer using the tabs provided. 5. T uck the rear flap of the boot in behind the Upper Moulding. Engaging Boot Center Section T ucking In Rear Flap UNDERST ANDING T.
Convertible T op Boot Cover Removal and Storage 1. Unsnap the snaps and remove the top cover boot. 2. Lay the boot cover flat with the center section retainer facing the rear of the car .
3. First fold the left side of the boot cover to the middle of the boot cover . 4. Second fold the right side of the boot cover to the middle, fitting it inside the left side of the boot cover and store it in the trunk or a dry secure area. CAUTION! Do not lay heavy objects on top of the boot or lay the boot on top of sharp/pointy objects.
CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failur e (low battery , etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw , which is found in the trunk under the convertible top storage area.
3. Using the latch handle raise the top until the two pins seat themselves in the windshield header . 4. Rotate the latch handle clockwise to open the latches. 5. Pull down and rotate the handle counterclockwise to engage the latches. 6. Raise the handle into the stowed position.
Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
Electric Remote-Control Mirrors — If Equipped The power mirror switch is located to the left of the steering column on the instrument panel. T o adjust the view in the outside mirrors, turn the rotary knob to the left (L), center (O) or Right (R) position.
An illuminated vanity mirror is on the sun visor . T o use the mirror , rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically . Closing the mirror cover turns off the lights. Sun Visor Sliding Feature The sun visors may be pulled out to provide extended coverage of the side glass.
UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnect™ phonebook enables you to stor e up to 32 names and four numbers per name.
The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www .chrysler .com/uconnect for supported phones. If your cellular phone supports a differ ent profile (e.g., Headset Profile), you may not be able to use any UCon- nect™ features.
example, you can either use the combined form voice command ⬙ Phonebook New Entry , ⬙ or you can break the combined form command into two voice com- mands: ⬙ Phonebook ⬙ and ⬙ New Entry .
NOTE: • www .chrysler .com/uconnect • www .dodge.com/uconnect • www .jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing.
phones are present in the vehicle, the UConnect™ system will use the priority 3 cellular phone when you make a call. Y ou can select to use a lower priority cellular phone at any time (refer to ⬙ Advanced Phone Connectivity ⬙ ). Dial by Saying a Number • Press the ’Phone’ button to begin.
you can say ⬙ John Doe, ⬙ where John Doe is a previ- ously stored name entry in the UConnect™ phone- book. Refer to ⬙ Add Names to Y our UConnect™ Phonebook, ⬙ to learn how to store a name in the phonebook.
four associated phone numbers and designations. Each language has a separate 32 name phonebook accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin.
• After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. Y ou can either say the name of a phonebook entry that you wish to delete or you can say ⬙ List Names ⬙ to hear a list of the entries in the phonebook from which you choose.
• T o call one of the names in the list, press the ⬙ V oice Recognition’ button during the playing of the desired name and say ⬙ Call. ⬙ NOTE: the user can also exercise ⬙ Edit ⬙ or ⬙ Delete ⬙ operations at this point. • The UConnect™ system will then prompt you as to number designation you wish to call.
Making a Second Call while Current Call in Progress T o make a second call while you are currently in a call, press the ’V oice Recognition’ button and say ⬙ Dial ⬙ or ⬙ Call ⬙ followed by the phone number or phonebook entry you wish to call.
Call T ermination T o end a call in progr ess, momentarily press the ⬘ Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial.
• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. T owing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ T owing Assistance.
When calling a number with your UConnect™ system that normally r equires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’V oice Recognition’ button and say the sequence you wish to enter followed by the word ⬙ Send.
Dialing Using the Cellular Phone Keypad Y ou can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures).
Information Service When using A T&T W ireless Service, dialing to phone number ⬙ #121, ⬙ you can access voice activated automated system to receive news, weather , stocks, traffic, etc.
Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin.
⬘ V oice Recognition’ button anytime while the list is being played and say the priority number of the phone you wish to delete. Things Y ou Should Know About Y our UConnect™ System V oice Recognition (VR) • Always wait for the beep before speaking.
• UConnect™ phonebook name tag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero).
156 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 157 3 I n f o r m a t i o n P r o v i d e d b y :.
158 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
Using body pressur e, move forward and rearwar d on the seat to be sure the seat adjusters have latched. W ARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
This seat also has a manual recline lever located just to the r ear of the power seat switch. T o recline, lean forward slightly before lifting the lever , then lean back to the desired position and release the lever . Lean forward and lift the lever to return the seatback to its normal position.
Manual Lumbar—If Equipped The Lumbar adjustment is located on the inboard side of the driver’s seat. T o increase support, rotate the handle down. Folding Front Passenger Seat — If Equipped The passenger front seat may be folded fully forward to provide additional cargo space.
Driver’s Seat Back Tilt—If Equipped How to operate the driver’s seat: 1. Push the lever down until seat back releases. 2. Push the seat back forward.
2. Push seat back forward until it slides towar d the dashboard. 3. T o return seat to a sitting position, rotate seat back upright until it locks. 4. Push seat rearward until the track locks. NOTE: The passenger front seat has a full recliner memory , which will allow the seat back to returned to its original position.
Heated Seats — If Equipped This featur e heats the fr ont driver’s and passenger’s seats. The control for the heater is located on the instru- ment panel, below the radio. After turning on the igni- tion, you may choose OFF , HIGH, or LOW heat settings.
Pressing the switch once will select high-level heating. Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off. When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated.
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Folding Rear Seat (Convertible) T o pr ovide additional storage area, each rear seatback can be folded forward. The seat back r elease knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
• Push and hold the button on the seatback and fold down the rear seatback. • Pull the release handle located on the outboard side of the seat. Lift up the seat and tumble the seat forward. • Attach the elastic strap, located at the base of the seat cushion, onto the hook bar on the center trim panel to hold the seat in place.
T o return the rear seat to it’s upright latched position, rotate the seat cushion rearwar d to latch the seat. Then lift the seatback to its upright latched position. NOTE: The elastic strap should be reinstalled in the clip on the base of the seat cushion before returning the seat to its normal position.
the left side seatback. Pull the right side seatback release knob to fold down the right side seatback. 2. From inside the vehicle, fold the rear seat back down flat.
3. Pull the release handle located at the bottom of the folded seat back and tumble the seat forward. 4. Attach the cinching tether strap, located at the side of the seat cushion, onto the hook bar on the center trim panel and tighten by pulling the cinching strap until the seat is secure.
T o return the tumbling rear seat to the latched (normal) position use the following procedur e: 1. Loosen the strap by pushing rearward on the cinching tether strap buckle.
NOTE: Prior to lifting either seatback to the upright position, be sure that the seat belt is brought forward to avoid trapping it behind the seatback. 3. Rotate the seat cushion rearward to latch the seat. Then lift the seatback to its upright latched position.
• Pull the release lever located on the outboard side of the seat. Lift up the seat and tumble the seat forward. • Lift up the release levers to disengage the seat from the floor attachments. • Using the handle on the seat, the seat assembly can now be lifted and removed from the vehicle.
T o reinstall the rear seat, insert the seat into the floor attachments. Lower the release levers of the seat to latch the front floor attachments and rotate the seat rearward to latch the seat.
Then move the safety catch located under the front edge of the hood, near the center and slightly to the right, and raise the hood. Use the hood prop rod clipped to the driver’s side of the engine compartment to secure the hood in the open position.
NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically .
NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically . Interior Lights The interior lights come on when a door or deck lid (convertible) is opened.
control is left in the Dome light position or a door is left open. The interior lights will remain on for only 90 seconds for all occurrence after that, until the engine is turned on and off. Interior light Defeat (OFF) Rotate the dimmer control to the ex- treme bottom “OFF” position.
Headlights, Parking Lights, Instrument Panel Lights T urn the end of the Multi-Function Control Lever to the first detent for parking light operation. T urn to the second detent for headlight operation. T o change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.
Fog Lights — If Equipped The front fog light switch is on the Multi-Function Control Lever . T o activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control lever . NOTE: The fog lights will only operate with the head- lights on low beam.
WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch on the control lever . The lever is located on the right side of the steering column. Rotate the control to select the desired wiper speed. Windshield Washers T o use the washer , pull the control lever toward you and hold while spray is desired.
CAUTION! In cold weather , always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.
NOTE: If the front wiper is operating when the ignition is turned off, the wiper will automatically return to the ⬙ Park ⬙ position. When the vehicle is restarted, the wipers will resume operation.
Adding W asher Fluid The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
NOTE: The T raction Control System will make buzzing or clicking sounds when the system is in operation. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 35 mph (56 km/h). The speed control lever is located on the right side of the steering wheel.
W ARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. Y ou could accidentally set the system or cause it to go faster than you want. Y ou could lose control and have an accident. Always leave the system OFF when you are not using it.
T apping “RESUME ACCEL” once will result i na2m p h (3 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 6 mph (10 km/h), etc. T o decrease speed while speed control is ON, push down and hold “SET DECEL”.
V ehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
For additional information on HomeLink 威 , call 1–800– 355–3515, or on the internet at www .homelink.com. W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured.
Programming The Universal T ransceiver For best results, install a new battery in the hand held transmitter before programming. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down.
4. Using both hands, press the hand held transmitter button and the desired Universal T ransceiver button. Do not release the buttons until step 5 has been completed. NOTE: Some entry gates and garage door openers may requir e you to replace step 4 with the procedures listed under Canadian Programming.
5. The indicator light in the Universal T ransceiver will begin to flash, first slowly and then rapidly . The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the pr ocedure.
NOTE: The assistance of a second person may make the following programming procedure quicker and easier . 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer .
The Universal T ransceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor .
2. This device must accept any interference that may be received including interference that may cause undesir ed operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment.
Press and hold the button in the center of the sunr oof switch to open the vent. The sunroof can be stopped at any position between closed and full vent.
W ARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. Y ou could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof.
It will accept a cigar lighter unit, which is part of the optional Smokers Package. T o preserve the heating ele- ment of the cigar lighter unit, do not hold the lighter in the heating position. As a child safety precaution, this outlet is powered by the ignition switch, only when the switch is in the ⬙ ON ⬙ or ⬙ ACCESSOR Y ⬙ positions.
This outlet is powered directly by the battery , regar dless of the ignition switch position. All accessories connected to this outlet should be removed or turned off when the vehicle is not in use, to pr otect the battery against discharge. The second is in the right rear cargo area.
Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e. cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery , even when not in use; i.e. cellular phones, etc. Eventually , if plugged in long enough, the vehicle’s battery will discharge suf ficiently to degrade battery life and/or prevent engine start- ing.
Push the upper button on the front of the armr est to raise the upper cover . Inside is a slot for a power cord, an area to stor e a cell phone, and other miscellaneous items. Push the lower button on the fr ont of the armr est, and raise the armrest for access to the lower storage bin.
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e. cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
W ARNING! • T o avoid tipping, lock the shelf securely in all positions. • Do not drive this vehicle with the liftgate open, or use the shelf as a seat. • Failure to follow these warnings could result in serious or fatal injury . Position 1 (T op) Insert the front outboard corners of the shelf panel into the top guides and slide forward.
Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward. Press down on the back of the shelf panel to lock it into place. W ARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle).
Position 4 (V ertical) Insert the front outboard corners of the shelf panel into the vertical guides behind the rear seatbacks near the floor and slide downward.
2. T wist the knob on the underside of the panel and lower the shelf leg. 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. W ARNING! Do not load objects over 100 lbs (45 kg) in position 5 (table). Failure to follow this warning could cause the shelf to collapse resulting in personal injury .
ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars.
CAUTION! T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately .
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Features ................. 2 1 8 䡵 Instrument Cluster—Base ................. 2 1 9 䡵 Instrument Cluster—Premium .............. 2 2 0 䡵 Instrument Cluster—T urbo ..........
▫ Electrical Disturbances .................. 2 3 9 ▫ AM Reception ....................... 2 3 9 ▫ FM Reception ........................ 2 3 9 䡵 Sales Code REF — AM/FM/CD (Single Disc) Radio W ith Optional Satellite Radio And Hands Free Phone Capability .
▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) .................... 2 6 2 ▫ Selecting Satellite Mode In REF , And RAQ, Radios ............................. 2 6 3 ▫ Selecting a Channel .................... 2 6 3 ▫ Storing And Selecting Pre-Set Channels .
INSTRUMENT P ANEL FEA TURES 218 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER—BASE UNDERST ANDING YOUR INSTRUMENT P ANEL 219 4 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER—PREMIUM 220 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER—TURBO UNDERST ANDING YOUR INSTRUMENT P ANEL 221 4 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the front passenger’s (right) side of the vehicle.
5. T achometer The white area of the scale shows the permissible engine revolutions-per -minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 6. T ransmission Range Indicator This display indicator shows the automatic transmission gear selection.
9. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position before engine start.
12. Brake System W arning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, ther e is a low brake fluid level or there is a problem with the anti-lock brake system.
the ON position. The light should illuminate for approxi- mately two seconds. The light should then turn of f unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer .
17. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 18. Anti-Lock W arning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual.
turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer . If the light comes on and remains on while driving, stop the vehicle and shut off the engine.
ELECTRONIC VEHICLE INFORMA TION CENTER (EVIC)–If Equipped The Electronic V ehicle Information Center (EVIC) fea- tures a driver-interactive display .
• Left Rear T urn Signal Lamp Out (with a single chime) • Right Front T urn Signal Lamp Out (with a single chime) • Right Rear T urn Signal Lamp Out (with a single chime) • RKE Battery Low (wi.
EVIC Functions Press the EVIC button until one of the following func- tions are displayed on the EVIC: • Compass/T emperature/Audio • A verage Fuel Economy • Distance T o Empty (DTE) • Elapsed.
For additional information regarding the compass, refer to Personal Settings (Customer Programmable Features) in this section. A verage Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds.
Press and release the EVIC button until Personal Settings is displayed in the EVIC. Use the EVIC button to display one of the following choices: Language When in this display you may select different languages for all display nomenclature, including the trip functions.
UNLOCK ALL DOORS is selected all of the doors will unlock at the first press of the remote keyless entry unlock button. Press and hold the EVIC button when in this display until “DRIVER’S DOOR 1ST” or “ALL DOORS” appears to make your selection.
NOTE: T urning the headlights on during the daytime causes the instrument panel lights to dim. T o increase the brightness, refer to “Lights” in this section.
North is great enough to cause the compass to give false readings. In order to ensure compass accuracy , the com- pass variance should be properly set according to the compass variance map zone that the vehicle is in. NOTE: Magnetic materials should be kept away from the Instrument Panel.
T o set the variance: with the ignition in the ON position, with a short button press (less than one seconds) press and release the EVIC button several times until you have displayed the Personal Settings (Customer Pr ogram- mable Features) menu.
calibration mode. The Cal indicator will come on con- tinuously in the EVIC display to indicate that the com- pass is now in the calibration mode and that the vehicle can now be driven to calibrate.
RADIO GENERAL INFORMA TION Radio Broadcast Signals Y our new radio will pr ovide excellent reception under most operating conditions. Like any system, however , car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning.
remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SA TELLITE RADIO AND HANDS FREE PHONE CAP ABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Power Switch/V olume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic V olume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. T o stop the search, press SCAN a second time.
AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the T one, Balance, and Fade Press the rotary TUNE control and BASS will be dis- played. T urn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will be displayed.
the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM,12 FM and 12 Satellite (if equipped) stations to be stored into push- button memory . The stations stored in SET 2 memory can be selected by pressing the push-button twice.
SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD. Pr ess the left side of the button to r eturn to the beginning of the current track, or return to the beginning of the previous track if the CD is within the first 10 seconds of the current selection.
RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. ⬙ MUTE ⬙ will be displayed. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning OFF the ignition will also return the sound from the speakers.
Operating Instructions - Satellite Radio — If Equipped Refer to the Satellite Radio section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SA TELLITE RADIO, HANDS .
Power Switch/V olume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic V olume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. T o stop the search, press SCAN a second time.
AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the T one, Balance, and Fade Press the rotary TUNE control and BASS will display . T urn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display .
T oggle the PTY button to select the following format types: Program T ype 16 Digit-Character Dis- play No program type or un- defined None Adult Hits Adult_Hits Alert Alert Alert Alert Classical Clas.
station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program T ype) mode, the PTY mode will be exited and the radio will tune to the preset station.
Operation Instructions - (CD MODE for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: Note: This Radio is capable of playing compact discs (CD), .
to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD MODE for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. ⬙ MUTE ⬙ will be displayed. Press the MUTE button a second time and the sound from the speakers will return.
the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD afte ra2m i n u t et i meout. If the CD is removed and there are no other CD’s in the radio, the radio will remain in CD mode and display ⬙ INSER T DISC” for 10 seconds.
Press the RND button a second time to stop Random Play . B u t t o n s1-6( C D MODE for CD Audio Play) Selects disc position s1-6f o rP l ay/Load/Eject. Notes On Playing MP3 Files The radio can play MP3 files, however , acceptable MP3 file recording media and formats are limited.
writing ⬙ ar e most likely multisession discs. The use of multisession for CD audio or MP3 playback may r esult in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
LOAD / EJECT - Eject Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to remove the disc.
AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly . SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure.
System Activation T o activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
mode when any other button is pushed, the ignition is turned OFF , or 5 minutes has passed since any button was pushed. ESN/SID Access W ith Navigation Radios Please refer to your Navigation User’s Manual.
NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539- 7474 to discuss options for channel blocking or unblock- ing.
Satellite Antenna T o ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible.
6. Do not expose the disc to direct sunlight. 7. Do not store the disc wher e temperatures may become too high. RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio.
The air conditioning system of your vehicle contains R-134a, a r efrigerant that does not deplete the ozone layer in the upper atmosphere. The controls are as follows: Fan Control Use this control to regulate the amount of air forced through the system in any mode you select.
NOTE: There is a dif ference in temperatur e between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet.
T emperature Control Use this control to regulate the temperature of the air in- side the passenger compart- ment. The blue area of the scale indicates cooler tem- peratures while the red ar ea indicates warmer tempera- tures.
Circulation Control Use this button to choose be- tween outside air intake or recir culation of the air inside the vehicle. A lamp will illu- minate when you are in recir - culate mode.
Operating Tips UNDERST ANDING YOUR INSTRUMENT P ANEL 271 4 I n f o r m a t i o n P r o v i d e d b y :.
W indow Fogging V ehicle side windows tend to fog on the inside in mild rainy or humid weather . T o clear the windows, use the A/C, P ANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recir culate without A/C for long periods as fogging may occur .
toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the ar ea of the windows thr ough which you view the outside mirrors. REAR WINDOW FEA TURES Electric Rear Window Defroster The push-button is located at the center of the instrument panel, below the radio.
CAUTION! T o avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window .
Adding W asher Fluid The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared. It is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 2 8 0 ▫ Automatic T ransaxle ................... 2 8 0 ▫ Manual T ransaxle ..................... 2 8 0 ▫ Normal Starting ...................... 2 8 0 ▫ Extremely Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) .
▫ AutoStick General Information ............ 2 8 9 䡵 Manual T ransaxle Operation ............... 2 9 0 ▫ 2.4 Liter T urbo— If Equipped ............. 2 9 2 ▫ Recommended Shift Speeds .............. 2 9 2 ▫ Downshifting .....................
䡵 Snow T ires ........................... 3 2 0 䡵 T ire Rotation Recommendations ............ 3 2 1 䡵 Fuel Requirements ...................... 3 2 2 ▫ 2.4L Standard Engine And 2.4L Standard T urbo Engine ........................ 3 2 2 ▫ 2.4L High Output T urbo Engine .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedur e.
W ARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury . CAUTION! T o prevent damage to the starter , do not crank the engine for more than 15 seconds at a time.
TURBOCHARGER ⴖ COOL DOWN ⴖ CHAR T Driving Conditions Idle T ime (in minutes) Before Shut Down Normal Driving Not requir ed. Aggressive Driving or Heavily Loaded 3 T railer T ow 5 ST ARTING AND OPE.
AUTOMA TIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Brake/T ransmission Interlock System This system prevents you from moving the gear shift out of Park and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON or ACC positions. Always depress the brake pedal first, before moving the gear selector out of P ARK.
(N) will continue to operate. This second gear limp-in feature allows the vehicle to be driven to a dealer for service without damaging the transaxle. In the event that the problem has been momentary , the transaxle can be reset to regain all forward gears.
W ARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake.
“R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive This range should be used for most city and highway driving. It provides smoothest up shifts and down shifts and best fuel economy .
AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transmission that offers manual gear shifting capability to pr ovide you with more control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance.
• Y ou can start out in first, second, or thir d gear . Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h). • The transmission will automatically downshift to first gear when coming to a stop. • Starting out in third gear is helpful in snowy or icy conditions.
Use each gear in numerical order - do not skip a gear . Be sure the transaxle is in FIRST gear , (not THIRD), when starting from a standing position. Damage to the clutch can result from starting in THIRD. For most city driving you will find it easier to use only the lower gears.
2.4 Liter T urbo— If Equipped The neutral position of the shift lever is located between THIRD and FOUR TH gear . This is the position the shifter lever will return to automatically when neutral is se- lected. When shifting into FIFTH gear , be sure to press the shifter lever all the way to the right to avoid acciden- tally selecting THIRD gear .
T ABLE 1-MANUAL TRANSAXLE NORMAL ACCELERA TION AND CRUISE SHIFT SPEEDS IN mph (km/h) EN- GINE SIZE MODE 1t o2 2t o3 3t o4 4t o5 2.4L T urbo Accel 15 (24) 25 (40) 40 (65) 45 (72) Cruise 15 (24) 25 (40) 42 (68) 45 (72) 2.
CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch. T o maintain a safe speed and prolong brake life, shift down to 2nd or 1st when descending a steep grade.
NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park.
BRAKE SYSTEM Y our vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function.
Anti-Lock Brake System (ABS) — If Equipped The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up.
The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is requir ed.
• and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. W ARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.
W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
A push-button at the center of the instrument panel, below the radio, turns the T raction Control System ON or OFF . The system is always in the “ON” mode unless: • The TRAC OFF switch has been .
This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled.
• European Metric tire sizing is based on European design standards. T ires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙ P ⬙ is absent from this tire size designation. Example: 215/65R15 96H • L T (Light T ruck)-Metric tire sizing is based on U.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and Tire Pressure T ire Placard Location NOTE: The proper cold tire inflation pressur e is listed on either the face of the driver’s door or the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
310 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, af fect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will r educe tr ead life r esulting in a need for earlier tire replacement. Underinflation also incr eases tire rolling resistance and results in higher fuel consumption.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
loading may be requir ed for high speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous.
Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only . Since this tire has limited tread life, the original tire should be r epaired (or replaced) and rein- stalled at the first opportunity .
Limited Use Spare — If Equipped The limited use spare tir e is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly . This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck.
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a r esult of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear . TIRE CHAINS Due to limited clearance, tire chains are not recom- mended.
Tire Rotation Recommendations T ires on the front and rear axles of vehicles operate at differ ent loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns.
FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard T urbo Engine Y our vehicle is designed to meet all emis- sion regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended.
Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the W orld W ide Fuel Charter , WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber . Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT .
overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may requir e immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now being sold as octane enhancers is not recommended.
the vehicle is raised. Have any abnormal conditions repair ed promptly . Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
NOTE: T ighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly , the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
Common T owing Definitions The following trailer towing r elated definitions will assist you in understanding the following information: Gross V ehicle W eight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver , passengers, cargo and tongue weight.
W ARNING! It is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if either rating is exceeded. Y ou could lose control of the vehicle and have an accident. T ongue W eight (TW) The downward force exerted on the hitch ball by the trailer .
T railer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package.
Engine/T ransmission Frontal Area Max. GTW (Gross T railer Wt.) Max. T ongue Wt. (See Note 1) 2.4L N/A and 2.4L T urbo/Automatic* 20 Sq. Ft 1000 lbs (454 kg) 1 10 lbs (50 kg) 2.4L N/A and 2.4L T urbo/Manual* 20 Sq. Ft. 1000 lbs (454 kg) 1 10 lbs (50 kg) * N/A (Naturally Aspirated) Refer to local laws for maximum trailer towing speeds.
Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers.
CAUTION! • A void towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual.
• Safety chains must always be used between your vehicle and trailer . Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • V ehicles with trailers should not be parked on a grade.
Information section of this manual on T read W ear Indicators for the proper inspection procedure. − When replacing tires refer to the T ires–General Infor- mation section of this manual on Replacement T ires for proper tire replacement procedur es.
W ARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. Y ou might not have brakes when you need them and could have an accident. T owing any trailer will increase your stopping dis- tance.
T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage.
NOTE: Check the automatic transmission fluid level before towing. T owing T ips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
If your vehicle is equipped with a manual transaxle, it may be towed with all four wheels on the ground, in a forward direction, at any legal highway speed, for any distance, if the transaxle is in neutral.
I n f o r m a t i o n P r o v i d e d b y :.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 3 4 4 䡵 If Y our Engine Overheats ................. 3 4 4 䡵 Jacking And T ire Changing ................ 3 4 6 ▫ Jack Location ........................ 3 4 7 ▫ Spare T ire Stowage .
HAZARD W ARNING FLASHER The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard W arning Flashers off.
If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle with the engine at idle, when safe.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual.
Jack Location The jack and jack-handle are stowed behind the right r ear side trim panel in the cargo area. Do not attempt to raise this vehicle using a bumper jack. Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism.
Spare T ire Removal Lift up the cover and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire. CAUTION! The hook is designed for use with the jack handle only .
Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. T o reinstall the cap, make sure it is properly lined up before pushing it on to the wheel.
Do not raise the vehicle until you are sur e the jack is securely engaged. 4. Raise the vehicle by turning the jack scr ew to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tir e.
100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly , have them checked with a torque wrench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free. Stow the lug wrench, and jack in their designated location.
W ARNING! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- axle cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
W ARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water .
W ARNING! Rapid acceleration on slippery surfaces is danger- ous. Unequal traction can cause sudden pulling of the front wheels. Y ou could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow , wet, mud, loose sand, etc.
and First gear . Usually the least accelerator pedal pres- sure to maintain the rocking motion without spinning the wheels is most effective. W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure.
more than 100 miles (160 km), the vehicle must be towed with the front wheels off the ground to avoid damage to the transaxle. Manual T ransaxle Y our vehicle may be towed if the gearshift lever is in NEUTRAL. If the transaxle is not operative, the vehicle must be towed with the front wheels off the ground.
CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failur e (low battery , etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw , which is found in the trunk under the convertible top storage area.
6. Raise the handle into the stowed position. 7. Close the convertible top motor bypass screw by turning the scr ew clockwise until it stops. T ighten the screw securely . NOTE: Failur e to tighten the bypass screw securely can cause convertible top operating concerns.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 2.4L T urbo Engine Compartment ............ 3 6 2 䡵 2.4L Engine Compartment ................ 3 6 3 䡵 Onboard Diagnostic System — OBD II ........ 3 6 4 ▫ Loose Fuel Filler Cap Message ............ 3 6 4 䡵 Emissions Inspection And Maintenance Programs .
▫ Maintenance-Free Battery ................ 3 7 5 ▫ Air Conditioner Maintenance ............. 3 7 7 ▫ Power Steering — Fluid Check ............ 3 7 8 ▫ Front Suspension Ball Joints .............. 3 7 8 ▫ Body Lubrication ..................
▫ Headlight Bulb Replacement ............. 4 0 8 ▫ Front Park/T urn Signal/Side Marker Lights . . 409 ▫ Front Fog Lights — If Equipped ........... 4 0 9 ▫ T ail/Stop, And Rear T urn Signal Lights ...... 4 1 0 ▫ Back Up Light Bulb .........
2.4L TURBO ENGINE COMP ARTMENT 362 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
2.4L ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 363 7 I n f o r m a t i o n P r o v i d e d b y :.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboar d diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap.
4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine.
DEALER SERVICE Y our dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner . Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedur e yourself.
could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level T o assure proper engine lubrication, the engine oil must be maintained at the correct level.
CAUTION! Overfilling the crankcase as indicated by an oil level above the “Max” mark on the engine oil dipstick will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature.
change your engine oil at every interval shown on schedule “A”—NON TURBO in the maintenance sched- ule section of this manual. If none of these apply to you, and your vehicle is equipped with a T urbo Charged Engine change your engine oil at every interval shown on schedule “A”—TURBO in the maintenance schedule section of this manual.
Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Synthetic Engine Oils There ar e a number of engine oils being promoted as either synthetic or semi-synthetic.
Drive Belts — Check Condition and T ension At the mileage shown in the maintenance schedules, check all drive belts for condition and proper tension.
CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly .
• Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected for prolonged period.
normal. The amount will depend on driving style. The air cleaner box should be cleaned out and a new make-up- air filter element should be installed during the normal air filter maintenance procedur e. W ARNING! The air cleaner can provide a measure of protection in the case of engine backfire.
W ARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water .
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test.
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product.
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors,liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear .
2. Push the r elease tab shown in the illustration and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a pr operly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner .
Adding Coolant Y our vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Y ears or 100,000 miles before replacement. T o prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
W ARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points T o Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
• Do not change the thermostat for summer or winter operation. If r eplacement is ever necessary , install ONL Y the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.
Brake System In order to assure brake system performance, all brake system components should be inspected periodically . Suggested service intervals can be found in the Mainte- nance Section. W ARNING! Riding the brakes can lead to brake failure and possibly an accident.
NOTE: Inspection of brake hoses should be done when- ever the brake system is serviced and at every engine oil change. W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately .
Use only manufacturers recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. W ARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking.
W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter .
Fluid Level Check The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. Procedure For Checking Fluid Level T o properly check the automatic transaxle fluid level, the following procedur e must be used: 1.
6. W ipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. If the fluid is hot, reading should be in the cross hatched area marked “HOT” between the upper two holes in the dipstick. If the fluid is cold, the fluid level should be between the lower two holes, into the area marked “LOW”.
If the transaxle is disassembled for any reason, the fluid and filter should be changed. Special Additives The manufacturer r ecommends against the addition of any fluid additives to the transaxle. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks.
Appearance Care And Protection From Corrosion Protection Of Body And Paint from Corrosion V ehicle body care requirements vary according to geo- graphic locations and usage.
• Use Mopar Cleaner W ax to remove road film, stains and to protect your paint finish. T ake car e never to scratch the paint. • A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
oven cleaner . A void automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.
• Oven cleaner • A car wash that uses carbide-tipped wheel cleaning brushes or acidic solutions. CAUTION! Many wheel cleaners contain acids that may harm the wheel surface. NOTE: Replacement costs for components damaged as a result of not following the recommended cleaning practices are considered the responsibility of the cus- tomer .
W ARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning Headlights Y our vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights.
Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
CAUTION! A void high pressure car washes, as they can damage the top material. Also, increased water pressure may force water past the weather strips. General Cleaning Careful vacuuming of the top before washing is helpful in removing dust and other foreign particles.
Cloth T op Additional Cleaning Procedure For additional cleaning assistance in removing stubborn stains, apply Mopar Convertible Cloth T op Cleaner (part number 05012245AA) to the complete stain, extending 2 inches (50 mm) beyond the stain. W ith a soft bristle brush, scrub in all directions over the stain.
INTEGRA TED POWER MODULE (IPM) An Integrated Power Module is located in the engine compartment near the air cleaner assembly . This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside of the cover .
Cavity Cartridge Fuse Mini Fuse Description 10 20 Amp Y ellow CCN, Power Locks 1 1 15 Amp Lt Blue Power Outlet 12 20 Amp Y ellow Ign Run/Acc In- verter 13 20 Amp Y ellow Pwr run/Acc Outlet RR 14 10 Amp Red IOD CCN/ Inte- rior Lighting 15 50 Amp Red RAD Fan Relay Battery Feed 16 15 Amp Lt.
Cavity Cartridge Fuse Mini Fuse Description 26 15 Amp Lt. Blue ENG ASD Relay Feed 2 27 10 Amp Red IGN RUN Only ORC Feed 28 10 Amp Red IGN RUN ORC/ OCM Feed 29 EMPTY 30 20 Amp Y ellow Heated Seats 31 1.
CAUTION! • When installing the Integrated Power Module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
REPLACEMENT BULBS LIGHT BULBS — Inside Bulb No. Center Console Floor Lamp ................. T 3 7 Climate Controls ...................... 6233137 Console Gear Selector ................... PC194 Dome Light (sedan) ...................... T579 Dome Light / Sport Bar Lights (convertible) .
BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening.
Front Park/T urn Signal/Side Marker Lights 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. Front Fog Lights — If Equipped 1.
T ail/Stop, and Rear T urn Signal Lights 1. Remove the screw attaching the tail light housing and remove the housing from the vehicle. 2. T wist the bulb socket 1/4 turn to remove it from the housing. 3. Pull the bulb out of the socket and replace. Back Up Light Bulb 1.
FLUIDS AND CAP ACITIES U.S. Metric Fuel (Approximate) 15 Gallons 56.7 Liters Engine Oil-W ith Filter 2.4 Liter Engines (Use API Certified SAE 5W -30 Engine Oil. 5.0 qts 4.7 Liters Cooling System * 2.4 Liter Engines (Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Miles Formula), or equivalent.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent. Engine Oil Use API Certified SAE 5W -30 Engine Oil.
Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Fluid. Mopar 威 A TF+4 Automatic T ransmission Fluid. Manual T ransmission Fluid. Mopar 威 A TF+4 Automatic T ransmission Fluid. Brake Master Cylinder Mopar 威 DOT 3, SAE J1703 should be used.
I n f o r m a t i o n P r o v i d e d b y :.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 4 1 6 䡵 Maintenance Schedule ................... 4 1 6 ▫ Schedule “B”—All Engines .............. 4 1 9 ▫ Schedule “A”—Non T urbo ............... 4 2 9 ▫ Schedule “A”—T urbo .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system.
• T axi, police, or delivery service (commercial ser- vice).† 〫 • Off-r oad or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut of f. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.
SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following condi- tions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or mor e of the conditions marked with an 〫 .
km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the ⬙ Maintenance Sched- ules ⬙ section of this manual. If none of these apply to you, and your vehicle is equ.
Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) (30 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace as necessary .
Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (35 000) (40 000) (45 000) (50 000) (55 000) (60 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X X Replace the engine air cleaner filter .
Miles 39,000 42,000 45,000 48,000 51,000 54,000 ( Kilometers) (65 000) (70 000) (75 000) (80 000) (85 000) (90 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X Change the brake fluid.
Miles 57,000 60,000 63,000 66,000 69,000 72,000 ( Kilometers) (95 000) (100 000) (105 000) (1 10 000) (1 15 000) (120 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Rotate tires. X X X Inspect the brake linings. X X Replace the engine air cleaner filter .
Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXXX Rotate tires. X X X Inspect the brake linings. X Inspect the engine air cleaner filter and replace as necessary .
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Rotate tires. X X Inspect the brake linings. X Change the brake fluid.
Miles 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Rotate tires. X X X Inspect the brake linings. X Replace the engine air cleaner filter .
* This maintenance is r ecommended by the manufacturer to the owner but is not requir ed to maintain the emis- sions warranty . ‡ This maintenance is not r equired if previously replaced. † This maintenance is required only for police, taxi, limousine type operation, or trailer towing.
SCHEDULE “A”—NON TURBO Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers ) (10 000) (20 000) (30 000) (40 000) (50 000) (60 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Rotate tires. X XXXXX Inspect the brake linings.
Miles 42,000 48,000 54,000 60,000 66,000 (Kilometers) (70 000) (80 000) (90 000) (100 000) (110 000) [Months] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . XXXXX Rotate tires. XXXXX Inspect the brake linings. X Replace the engine air cleaner filter .
Miles 72,000 78,000 84,000 90,000 96,000 102,000 (Kilometers) (120000) (130000) (140 000) (150 000) (160 000) (170 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X X X X X X Rotate tires. X X X X X X Inspect the brake linings.
Miles 108,000 1 14,000 120,000 (Kilometers) (180 000) (190 000) (200 000) [Months] [108] [1 14] [120] Change engine oil and engine oil filter . X X X Rotate tires. X X X Inspect the PCV valve and replace if necessary . * ‡ X Replace the air cleaner filter .
SCHEDULE “A”—TURBO Miles 5,000 10,000 15,000 20,000 25,000 30,000 (Kilometers) (8 000) (16 000) (24 000) (32 000) (40 000) (48 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Rotate tires. X XXXXX Inspect the brake linings.
Miles 35,000 40,000 45,000 50,000 55,000 (Kilometers) (56 000) (64 000) (72 000) (80 000) (88 000) [Months] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . XXXXX Rotate tires. XXXXX Inspect the brake linings. X Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles.
Miles 60,000 65,000 70,000 75,000 80,000 85,000 (Kilometers) (96 000) (104 000) (1 12 000) (120 000) (128 000) (136 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X X X X X X Rotate tires. X X X X X X Inspect the brake linings.
Miles 90,000 95,000 100,000 105,000 (Kilometers) (144 000) (156 000) (160 000) (168 000) [Months] [108] [1 14] [120] [126] Change engine oil and engine oil filter . X X X X Rotate tires. X X X X Inspect the brake linings. X Replace the engine air cleaner filter .
Miles 1 10,000 1 15,000 120,000 (Kilometers) (177 000) (185 000) (193 000) [Month] [132] [138] [144] Change engine oil and engine oil filter . X X X Rotate tires. X X X Inspect the PCV V alve and replace if necessary . * X Replace the engine air cleaner filter .
I n f o r m a t i o n P r o v i d e d b y :.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V e h i c l e .............................. 4 4 0 ▫ Prepar e For The Appointment ............ 4 4 0 ▫ Prepar e A List ........................ 4 4 0 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional char ges with the service manager .
technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner . This is why you should always talk to your dealer’s service manager first.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer .
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .
on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- mance. W ARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
ABS (Anti-Lock Brake System) .............. 2 9 7 Adding Engine Coolant (Antifreeze) .......... 3 8 4 Adding Fuel ........................... 3 2 6 Adding W asher Fluid .................. 187,275 Additives, Fuel ......................... 3 2 4 Air Cleaner , Engine (Engine Air Cleaner Filter) .
Special Additives ...................... 3 9 4 Autostick ............................. 2 8 9 Back-Up Lights ......................... 4 1 0 B a l l J o i n t s ............................. 3 7 8 Battery ............................... 3 7 5 Keyless T ransmitter Replacement (RKE) .
Caution, Exhaust Gas ..................... 1 1 4 CD (Compact Disc) Player ............... 240,248 CD (Compact Disc) Player Maintenance ........ 2 6 5 Cellular Phone ....................... 136,266 Center High Mounted Stop Light ............ 4 1 0 Chains, T ire .
Drain, Flush, and Refill .................. 3 8 3 Inspection ........................... 3 8 5 Points to Remember ................. 384,386 Pressur e Cap ......................... 3 8 4 Selection of Coolant (Antifreeze) ........... 3 8 3 Corrosion Protection .
Emergency Deck Lid Release Latch (Convertible) . . 41 Emergency , In Case of Jacking ............................. 3 4 6 Jump Starting ......................... 3 5 1 T o w i n g ............................. 3 5 5 Emergency Seat Back Release (Sedan) .
Fluid Leaks ............................ 1 1 5 Fluid Level Checks Automatic T ransaxle .................... 3 9 2 F l u i d s ................................ 4 1 2 Fluids, Lubricants and Genuine Parts .......... 4 1 2 Fog Light Service ..............
Gauges Coolant T emperature .................... 2 2 2 Fuel ................................ 2 2 2 Odometer ........................... 2 2 3 T achometer .......................... 2 2 3 Gearshift .............................. 2 8 6 General Information .
Instrument Panel and Controls .............. 2 1 8 Instrument Panel Cover ................... 3 9 9 Instrument Panel Lens Cleaning ............. 4 0 0 Integrated Power Module .................. 4 0 3 Interior Appearance Care .................. 3 9 8 Interior Lights .
Dimmer Switch, Headlight ............... 1 8 1 Engine T emperature W arning .............. 2 2 6 F o g .......................... 183,227,409 Front Replacement ..................... 4 0 8 Headlight Switch ...................... 1 8 2 Headlights ......
Maintenance Schedule Schedule “A”-Non T urbo ................. 4 2 9 Schedule “A”-T urbo .................... 4 3 3 Schedule “B” ......................... 4 1 9 Schedule “B”-All Engines ................ 4 1 9 Maintenance Schedules ....
F i l t e r ............................... 3 7 1 Identification Logo ..................... 3 7 0 Materials Added to ..................... 3 7 1 Q u a l i t y ............................. 3 7 0 Recommendation .................... 370,41 1 Synthetic .
Pregnant W omen and Seat Belts ............ 5 5 , 8 9 Preparation for Jacking .................... 3 4 8 Pretensioners Seat Belts ........................... 5 3 , 8 7 Programmable Electronic Features ...... 194,198,232 Programming T ransmitters (Remote Keyless Entry) .
Safety Checks Outside V ehicle ............... 1 1 5 Safety Defects, Reporting .................. 4 4 3 Safety Information, T ire ................... 3 0 2 Safety T ips ............................ 1 1 4 Satellite Radio .......................... 2 6 1 Satellite Radio Antenna .
Security Alarm (Theft Alarm) ................ 3 6 Sentry Key (Immobilizer) ................. 1 5 , 3 7 Sentry Key Programming ................... 1 7 Service and Maintenance .................. 4 1 6 Service Assistance ....................... 4 4 0 Service Contract .
T emperature Gauge, Engine Coolant ....... 222,345 T ether Anchor , Child Restraint ............ 7 6 , 1 0 9 Theft Alarm (Security Alarm) ................ 3 6 Theft System (Security Alarm) ............... 3 6 T ilt Steering Column ....................
Recreational .......................... 3 4 0 W e i g h t .............................. 3 3 2 T raction .............................. 3 5 4 T raction Control ...................... 188,300 T raction Control Switch ................. 188,300 T r a i l e r T o w i n g .
Uniform T ire Quality Grades ................ 4 4 5 Universal T ransmitter ..................... 1 9 2 Unleaded Gasoline ....................... 3 2 2 Untwisting Procedur e, Seat Belt ............ 5 2 , 8 6 V acuum/V apor Harnesses ................. 3 8 7 V a n i t y M i r r o r s .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Chrysler PT Cruiser (2006) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Chrysler PT Cruiser (2006) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Chrysler PT Cruiser (2006), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Chrysler PT Cruiser (2006) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Chrysler PT Cruiser (2006), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Chrysler PT Cruiser (2006).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Chrysler PT Cruiser (2006). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Chrysler PT Cruiser (2006) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
