Manuel d'utilisation / d'entretien du produit Crossfire (2006) du fabricant Chrysler
Aller à la page of 296
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ........................... 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ..............
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual ................. 4 䡵 W arnings And Cautions .......
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your Crossfire. It is supplemented by a W arranty Information Booklet and various customer-oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 9 ▫ Keys ............................... 9 ▫ Obtaining Replacement Keys .............. 1 0 ▫ Ignition Key Removal ................... 1 0 ▫ Key-In-Ignition Reminder .
䡵 Power W indows ........................ 2 1 ▫ Power W indow Operation W ith The Convertible T op Switch (Roadster Only) ............... 2 2 䡵 Rear Liftgate/Decklid Release .............. 2 2 䡵 Occupant Restraints ..................... 2 2 ▫ Lap/Shoulder Belts .
A WORD ABOUT YOUR KEYS Y ou can insert the double-sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys only from an authorized dealer .
Obtaining Replacement Keys Y our vehicle is equipped with a theft deterrent locking system requiring a special key manufacturing pr ocess. For security reasons, replacement keys can only be ob- tained from your authorized dealer . Important! Removing the key from the steering lock activates the start lock-out.
GLOVE COMP ARTMENT LOCK The glove compartment can be locked by turning the key straight up to the vertical or right position, and then removing the key . T o unlock the glove compartment, turn the key to the horizontal or left position, and then remove the key .
The doors can be unlocked by pulling on the inside door handle, pressing and releasing the top portion of the central locking switch located in the console, or by pressing and releasing the Unlock transmit button on the key fob. Both doors can also be unlocked by turning the key counterclockwise in the driver’s door .
NOTE: The fuel filler door and center console (roadster only) cannot be locked or unlocked with the central locking switch. Automatic Central Locking The central locking switch also operates the automatic central locking feature.
Perform the quick system check which follows: Use the remote transmitter to set the alarm. If the parking lamps flash three times, the system is operating prop- erly . If not, there is a problem with a switch or the system. See your authorized dealer for service.
Press the Unlock transmit button on the key fob once to unlock driver’s door , rear liftgate/decklid, fuel filler door , and center console (roadster only). Pr ess the Unlock transmit button twice to unlock both doors, rear liftgate/ decklid, fuel filler door , and center console (roadster only).
Panic Alarm The panic alarm unlocks the driver’s door , turns on the interior lights, flashes the foglights and sounds the horn for about three minutes or until the alarm is turned off. The vehicle can be driven while in the Panic mode. T o Use the Panic Alarm: Press and hold the Panic button to activate the alarm.
T ransmitter Battery Service The recommended replacement Lithium battery is Pana- sonic 威 CR 2025 or equivalent. T o change the batteries: • Press release button (2) on the key fob. The key folds out. • Press the battery cover (1) in the direction of the arr ow .
approximately 30 seconds, insert the key in the ignition and turn it to the ON/RUN position. The remote control should once again be operational. SECURITY ALARM SYSTEM The system monitors the doors, rear liftgate/decklid, hood, and ignition for unauthorized operation.
The tow-away alarm remains switched off until the vehicle is locked again with the key or the remote control, at which time it is automatically reactivated. DECKLID INTERNAL EMERGENCY RELEASE - ROADSTER As a security measure, a Decklid Internal Emergency Release lever is built into the decklid latching mecha- nism.
W ARNING! If the battery voltage drops below the minimum threshold at any time, the T runk Internal Emergency Release will not function. W ARNING! The T runk Internal Emergency Release will not function during the convertible top operation.
POWER WINDOWS The power window switches are located in the console. T o operate, turn the key in the ignition switch to the ACC or ON/RUN position. Press the switch in to the resis- tance point to open; release the switch when the window is in the desired position.
Power Window Operation With The Convertible T op Switch (Roadster Only) The power windows can also be operated by using the convertible top switch. T o operate, turn the key in the ignition switch to the ON/RUN position. Press down on the rear of the con- vertible top switch twice to open the windows.
Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up.
In cases of other frontal impacts, roll overs, certain side impacts, rear collisions or other accidents without suffi- cient fr ontal or rear impact for ces, the emergency tension- ing r etractors will not be activated. The driver and passenger will then be protected by the fastened seat belts and inertia reel in the usual manner .
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up a little on the shoulder belt, as shown.
W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for the driver and passenger as a supplement to the seat belt r estraint systems. The driver’s airbag is mounted in the steering wheel. The passenger frontal airbag is mounted in the instrument panel, under a cover marked SRS/AIRBAG.
The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe front collisions. In certain types of collisions, both the front and side airbags may be trigger ed.
W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
• The Occupant Restraint Controller monitors the readi- ness of the electronic parts of the system whenever the ignition switch is in the ST ART or ON/RUN positions. These include all of the items listed above except the knee bolster , the instrument panel, and the steering wheel and column.
then quickly deflate while helping to restrain the driver and passenger . The airbag gas is vented through the airbag material towards the instrument panel.
If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and passen- ger as the airbags deploy and unfold.
• When a side impact above a predetermined threshold occurs, the sensors signal the inflator on the impacted side of the vehicle. A large quantity of nontoxic nitrogen gas is generated to inflate the airbag. The door panel opens to allow the airbag to inflate to its full size.
• The operational readiness of the side airbag system is verified by the airbag indicator light in the instrument cluster when turning the key in the ignition switch to the ON/RUN position. If no fault is detected, the light will go out after approximately four seconds.
Passenger Front Airbag On/Off Switch The on/of f switch is located at the right end of the instrument panel and is accessible by opening the pas- senger door .
T o turn OFF the passenger front airbag, use the on/off switch located on the instrument panel. NOTE: When the passenger airbag is turned off, the yellow airbag off light will illuminate. T o Shut Off the Passenger Airbag: • Place the ignition key in the on/of f switch, turn the key clockwise, and remove the key from the switch.
T o T urn On the Passenger Airbag: • Place the ignition key in the on/of f switch, turn the key counterclockwise, and remove the key from the switch. This will turn on the passenger airbag. The Passenger Airbag Off light on the console will turn off, or will not be illuminated when the ignition is turned to the ON position.
Airbag Light Y ou will want to have the airbags ready for your protection in case of a collision. While the airbag Supplemental Restraint System (SRS) is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately .
• The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs. (9 kg). “Convertible” child seats can be used either rearward-facing or forward-facing in the vehicle.
• The restraint must be appropriate for your child’s weight and height. Check the label on the r estraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly , it may not work when you need it.
• Check belt fit periodically . A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
The passenger seat tether anchorage is located on the back of the seat cushion frame. It is visible by moving the passenger seat forward in the vehicle.
W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
T o attach the tether strap to the anchor , move the seatback fully forward. Pass the child r estraint tether hook over the top of the seat, through the strap near the top of the seat back, and attach it to the anchor bar behind the passenger seat, below the seatback.
ENGINE BREAK-IN RECOMMENDA TIONS The engine in your new Crossfir e does not require a long break-in period. Following these few simple guidelines is all that is necessary for a good break-in. • Drive your vehicle at moderate vehicle and engine speeds during the first 1,000 miles (1,600 km).
Safety Checks Y ou Should Make Inside the V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor , torn webbing, etc.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Convertible T op Operation ................ 5 2 ▫ T o Lower The T op ...................... 5 3 ▫ T o Raise The T op ...................... 5 8 ▫ Convertible T op Lamp And Audible Signal Chart .
▫ Heated Seats (If Equipped) ............... 7 3 䡵 T o Open And Close The Hood ............. 7 4 䡵 Interior Lights ......................... 7 5 ▫ Front Map/Reading Lights ............... 7 5 ▫ Battery Saver Feature ................... 7 5 ▫ Instrument Panel Lighting .
▫ Using The Universal T ransceiver .......... 1 0 1 ▫ Erasing Universal T ransceiver Buttons ....... 1 0 1 ▫ Reprogramming a Single Button ........... 1 0 1 ▫ Security ............................ 1 0 1 䡵 Umbrella Hook ......................
CONVERTIBLE TOP OPERA TION W ARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision.
CAUTION! When opening and closing the convertible top, make sure that: • There is sufficient clearance of at least 6 ft. (1.8m) for the convertible top to move up. • Nothing is placed on the tonneau cover . • The outside temperature is above 32°F (0°C).
CAUTION! T o avoid possible damage to the tonneau cover and convertible top, do not allow the convertible top to remain in the suspended position. After approxi- mately 10 minutes in the suspended position, the hydraulic pressure will be released which will allow the top and the tonneau cover to lower .
NOTE: See label attached to underside of decklid. 2. Make sure the decklid is closed. CAUTION! Be sure to turn the ignition to the “ON/RUN” position before releasing the top from the wind- shield header . The windows will not go down if the top is released from the header without the ignition turned “ON”.
NOTE: Once the release handle is r otated, the windows will automatically go down. 5. Push up on the convertible top latch handle to create a gap between the header and top of approximately 8 inches (200 mm). As soon as the top is free, rotate the latch handle counterclockwise just over one quarter turn and push it up into the stored position.
NOTE: Once the top is lowered and the audible signal is heard, you can continue to push the convertible top switch down or push it within 2 seconds to raise the windows.
T o Raise The T op: 1. Make sure the rear cargo compartment divider is still secured in the vertical position. 2. Make sure the decklid is closed. 3. T urn the ignition key to the ON/RUN position and press down on the front of the convertible top switch.
6. Pull the latch handle and convertible top down to engage the top with the header . 7. When the top engages to the header , turn the latch handle counterclockwise just over one quarter turn to the lock position and push the latch handle up to the stored position.
8. Once the top has been raised and locked, the cargo compartment divider can be unhooked and folded for- ward to increase the car go compartment capacity .
Convertible T op Lamp and Audible Signal Chart Below is a table containing all of the visual and audible signals that can be seen or hear d during top operation or if a fault is present.
CONSOLE FEA TURES The console has a power outlet/cigar lighter , an ash tray with a coin holder , a cupholder (if equipped), and the passenger airbag light.
Storage Compartments There is a storage compartment in the console. T o open the storage compartment, lift the lid with the finger depressions on either side. T o close, lower the lid until the lock engages. On some models, a cargo net for storage is located in the footwell area on the passenger side.
A storage pouch is located on the rear wall between the seats, and the driver’s sunvisor has a document strap. W ARNING! Keep compartment lids closed. This will help to prevent stored objects from being thrown about and injuring vehicle occupants during an accident.
Coin Holder W ith the ashtray open, folding down the cover plate reveals the coin holder , which can accommodate nine coins in various sizes up to a U.S. quarter . The coin slots are shaped to retain the coins, and the cover plate ensur es that the coins remain in the coin holder .
Glove Compartment T o lock the glove compartment, turn the key to the right and remove. T o unlock, turn the key to the left and remove. Pull on the handle to open the glove compartment. CUPHOLDER (If Equipped) The cupholder is located in the console.
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window . A two point pivot system allows for horizontal and vertical mirror adjustment.
Power Remote Control Outside Mirrors The mirrors can be adjusted by using the remote control located in the console. Rotate the switch to the right to select the right mirror , rotate to the left to select the left mirror . Then use the switch to adjust the selected mirror to the desired direction.
V anity Mirrors A vanity mirror is on each sun visor . T o use the mirror , rotate the sun visor down and slide open the mirror cover . SEA TS Y our vehicle’s seats can be adjusted either manually or electrically , depending on how your vehicle is equipped.
NOTE: When moving the seat, be sure that there are no items in the footwell or behind the seats. Otherwise you could damage the seats. Manual Seat Adjustments (If Equipped) Seat Height (Drivers Seat Only) • Pull up on handle 3. • T o lower the seat, use your body weight to push the seat downward.
Forward/Rearward • Pull up on handle 4. • Move the seat forwar d or backward to your desired position which allows you to reach the pedals com- fortably . • Let go of handle 4. The seat should make an audible click when positioned properly . • Check for proper engagement before driving.
Driver Eight-Way Power Seat (If Equipped) The switches to adjust the power seats ar e located on the outboard side of each seat. The driver’s seat features eight-way power adjustment - horizontal, vertical, cush- ion tilt and back angle.
Passenger Four-Way Power Seat (If Equipped) The switches to adjust the passenger seat are also on the outboard side of the seat. The passenger seat provides four-way adjustment - horizontal and back angle. Heated Seats (If Equipped) This feature heats the driver and passenger seats.
TO OPEN AND CLOSE THE HOOD T o open the hood, pull the release lever located inside your vehicle, below the instrument panel. Then, reach under the hood and pull upward on the safety latch and lift the hood. T o prevent possible damage, close the hood by dropping it from approximately 12 inches (30 cm).
INTERIOR LIGHTS A two-position mode selector switch controls the interior lights located in the overhead console. The AUTO mode turns the lights on when a door is open or ajar , or when locking or unlocking the vehicle. AUTO mode also has a “fade to of f” feature.
Instrument Panel Lighting W ith the parking lights or headlights on, rotate the dimmer contr ol to the left of the speedometer to incr ease or decrease brightness of the instrument panel.
Lights-On Reminder If the headlights or parking lights are left on after the ignition is turned off, a warning will sound if the driver’s door is opened.
CAUTION! Standing lamps are intended for short term use when parking. If these lights are left on for a long period of time, your car’s battery may drain, causing a possible starting problem. Assure that the head- lamp switch is in the OFF position when leaving the vehicle.
T o operate the turn signals continuously , move the con- trol lever up or down past the point of resistance. The operation is automatically canceled when the steering wheel is turned to a large enough degree. If one of the turn signal lights fail, the turn signal indicator system flashes and sounds at a faster than normal rate.
Passing Light Y ou can signal another vehicle with your headlights by lightly pulling the multifunction control lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the control lever is released.
Push the end of the lever inward and hold it to activate the wiper and washer together . Mist Function Push the end of the multifunction control lever inward briefly for a single wipe without adding washer fluid. Use this feature only when the windshield is wet.
TELESCOPING STEERING COLUMN Unlock the steering column by pulling out the handle located directly below the column. The indicator light located in the instrument cluster will come on. T o lengthen or shorten the steering column, pull out or push in the steering wheel.
NOTE: If the indicator light in the instrument cluster does not go out after starting the engine, the telescoping column is not locked properly . Do not drive the vehicle until you have properly locked the steering column.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressur e, even if under -inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
The TPM system will cause the indicator lamp in the instrument cluster to illuminate whenever the pr essure in one tire falls 25% below the recommended pressur e shown on the vehicle’s tire label. NOTE: The pressur e in your tires changes with tem- perature.
CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor dam- age may result when using replacement equipment that is not of the same size, type, and/or style.
REAR SPOILER CAUTION! Do not push or pull on the spoiler when deployed. Damage to the spoiler could result. A rear spoiler enhances vehicle stability . The rear spoiler deploys automatically when vehicle speed reaches ap- proximately 62 mph (100 km/h).
The spoiler control also incorporates an emergency stop feature. If, for any reason, spoiler motion needs to be stopped, pressing either the top or bottom of the switch will stop the spoiler motion. Once the deployment speed is reached, however , the spoiler deploys to its full up position.
W ARNING! Do not drive the vehicle at speeds above 62 mph (100 km/h) if the red spoiler warning indicator is illumi- nated. Y ou could have reduced vehicle stability and control. W ARNING! Keep hands and fingers away from the spoiler and spoiler linkage when the spoiler is deploying or retracting.
The BAS is designed to maximize the vehicle’s braking capability during emergency braking maneuvers. The system applies maximum power boost to the brakes more quickly in emergency braking conditions than might otherwise be affor ded solely by the driver’s brak- ing style.
If the malfunction indicator light stays illuminated, have the BAS and ESP checked at your authorized dealer as soon as possible. ELECTRONIC ST ABILITY PROGRAM (ESP) W ARNING! ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded.
T o improve the vehicle’s traction when driving with snow chains, or starting off in deep snow , sand or gravel, switch off the ESP system by pressing the upper half of the ESP switch. W ith the ESP system switched off, the engine torque reduction featur e is cancelled.
CAUTION! If the vehicle is towed with the front axle raised, the engine must be shut off (key in the ignition switch to the OFF/LOCK or ACC position). Otherwise the ESP will immediately be engaged and will apply the rear wheel brakes.
ELECTRONIC SPEED CONTROL The electronic speed control automatically maintains the set speed by actively regulating the throttle setting. Any speed above approximately 20 mph (30 km/h) can be maintained with the electronic speed control by operat- ing the lever .
T o accelerate and set a speed, lift the lever up. Lift and hold the lever to accelerate, or lift and release to set a speed. T o decelerate and set a speed, press the lever down. Press down and hold the lever to decelerate, or press down and release to set a speed.
T o Deactivate A soft tap on the brake pedal, or normal brake pressure while slowing the vehicle, will deactivate the speed control without erasing the memory . Pushing the speed control lever forward or turning the key in the ignition switch to the OFF/LOCK position will turn of f the speed control and erase the memory .
Using Speed Control On Hills Y our vehicle is equipped with interactive speed control. This feature activates when driving up or down hills with the speed control engaged and the driver’s foot off the accelerator . W ARNING! Speed control can be dangerous where the system can’t maintain a constant speed.
W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature, as required by federal safety stan- dards.
NOTE: Step 3 does not have to be followed to program additional hand-held transmitters. 4. Choose one of the thr ee buttons to program. Place the hand-held controller 1–3 inches (25–76 mm) from the universal transceiver while keeping its indicator light in view .
If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Programming Steps 8-10 to complete programming of a rolling code equipped device (most commonly a garage door opener). 8. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button.
5. Continue to press and hold the universal transceiver button while you press and r elease every two seconds (“cycle”) your hand-held transmitter until the frequency signal has successfully been accepted by the universal transmitter . (The indicator light will flash slowly and then rapidly .
This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undes- ired operation.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instruments And Controls ................ 1 0 4 䡵 Instrument Cluster ..................... 1 0 5 䡵 Instrument Cluster Description ............ 1 0 7 䡵 “Infinity Modulus” AM/FM Stereo Radio W ith Single-Disc CD Player And GPS Navigation .
INSTRUMENTS AND CONTROLS 104 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER The instrument cluster displays are activated by either opening the door , pressing the left button within the cluster , or turning the key in the ignition switch to the ON/RUN position.
106 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTION 1. Low Windshield W asher System Fluid Level W arning Light W ith the key in the ignition switch turned to the ON/RUN position, the indicator light comes on.
CAUTION! The TPMS is designed to monitor your tire pressure and will not function as a tire pressure gauge. After adjusting the air pressure in a tire, there will be a delay before the system updated the display NOTE: The TPMS can inform you about a low tire pressur e condition, but it does not replace normal tire maintenance.
CAUTION! Continuing to drive with an overheated engine cool- ing system can cause damage to the engine or other components. 5. Fuel Gauge When the ignition is in the ON/RUN position, the pointer will show the level of fuel remaining in the tank.
10. Brake System W arning Light The dual brake system provides a reserve braking capability if a failure occurs in a portion of the hydraulic system. This light monitors both the brake fluid level and the parking brake.
The indicator light will come on when the exterior light fails. If a brake light fails, the light outage indicator will come on when applying the brake and stays on until the engine is turned off. NOTE: If additional lighting equipment is installed (e.
The seat belt indicator light will remain lit until the seat belts are fastened. 15. Charging System Indicator Light Should the charging system indicator light fail to come on prior to starting when t.
The display can be adjusted with the knob/button lo- cated to the left of the clock. 18. Gear Indicator For automatic transmission vehicles, the current gear shift selector range is indicated in the gear range indica- tor display .
T o reset the trip odometer , press the knob/button once with the key in the ON/RUN position. Press the knob/ button twice with the key removed or in the OFF/LOCK or ACC position. The FSS permits a flexible service schedule that is dir ectly related to the operating conditions of the vehicle.
or while driving when reaching the service warning threshold. It can be canceled manually by pressing the knob/button. Once the suggested term has passed, the message plus either the symbol for Servic.
W ARNING! The outside temperature indicator is not designed to serve as an ice-warning device and is unsuitable for that purpose. Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice.
W ARNING! Do not drive the vehicle until you have properly locked the steering column. 26. Check Engine Light This light is part of an onboard diagnostic system that monitors the emissions and en- gine control systems. If a pr oblem is detected in one of these systems, the Check Engine light will come on.
CHECKING ENGINE OIL LEVEL A sensor in the oil pan allows oil level to be checked without opening the hood. It provides an accurate mea- surement of oil level, whereas the low engine oil level indicator warns that oil level is definitely too low .
“INFINITY MODULUS” AM/FM STEREO RADIO WITH SINGLE-DISC CD PLA YER AND GPS NA VIGA TION (OPTIONAL - See separate User’s Manual) AM/FM STEREO RADIO WITH SINGLE-DISC CD PLA YER INFINITY MODULUS Entertainment Systems A pr emium Infinity Modulus AM/FM stereo, single-disc CD audio system is standard equipment on some mod- els.
The volume is controlled by rotating the ON/OFF knob to the left or right. Audio (AUD) Settings • Bass (BASS) Press the AUD button repeatedly until BASS appears. Rotate the right rotary control for the desir ed level (from -9 to +9). • T reble (TREB) Press the AUD button repeatedly until TREB appears.
FM AS – An autostore feature will store the 9 current stations with the strongest signal on station buttons 1-9 in the order of their signal quality . Press the FM button repeatedly until FM AS is displayed to perform an autostore scan. Press the multifunction button labeled AS repeatedly until AS-SEEK is displayed.
Press the button again to keep the received program. If the selected station does not transmit a PTY identifica- tion, the display will show NO PTY . If all criteria for evaluating RDS are not met, the unit will only display the frequency .
AM-AM AS The system has two AM modes available. Press the AM button repeatedly until the band or operation mode is selected. T o search in this mode, press the right rotary control/push button and the abbreviation SC is dis- played. Receivable stations can be heard for eight sec- onds.
CAUTION! Before inserting a CD, assure that a CD is not already in the player . Press the CD button; if the display shows NO CDS, a new CD can be inserted. If a CD is already loaded, press and release the EJT button and allow time for the current CD to be ejected.
• Relative T ime Display (T) Press the multifunction button T for the time of the currently playing track to be displayed for approxi- mately eight seconds. • Random Play (RP) Press the multifunction button RP for random genera- tion of the next track to be played.
Mono/Stereo In order to suppress reception-r elated interference, three differ ent parameters can be set to optimize reception. T o activate, call up the user menu, then press the right rotary contr o.
Call up the user menu, then press the right r otary control/push button repeatedly until AUDIO PH or PH MUTE is displayed (depending on the currently selected setting, you may need to turn the knob also for your selection). COMP ACT DISC MAINTENANCE T o keep the compact discs in good condition, take the following precautions: 1.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna.
The settings and controls are as follows: T emperature Control Use the driver or passenger temperature control to regulate the temperature of the air inside the passenger compartment. The blue area of the control indicates cooler temperatures, while the r ed ar ea indicates warmer temperatures.
Basic Setting - Air Conditioner Press the air conditioning ON/OFF switch. The light in the switch will illuminate. Select a temperature for each side of the passenger compartment. Select the air volume with the fan control switch, at least to position 1.
control switch to position 1 or higher . Close the center , left, and right side air outlets. T urn the defroster outlets for the side windows to the detent position.
Climate Control - OFF T o switch the climate control off, set the air volume control switch to position 0. The fresh air supply to the vehicle interior is shut off. While driving, use this setting only temporarily , otherwise the windshield could fog up.
after approximately 30 minutes, at outside temperatures above approximately 40°F (5°C); after appr oximately five minutes, if the A/C button is pressed. At high outside temperatures, the system automatically engages the recir culated air mode for approximately 30 minutes, thereby increasing the cooling capacity perfor- mance.
Operating Tips 134 UNDERST ANDING YOUR INSTRUMENT P ANEL.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 1 3 7 ▫ Normal Starting ...................... 1 3 7 ▫ Extremely Cold W eather (Below -20°F Or -29°C) . 138 ▫ If Engine Fails T o Start ................. 1 3 8 ▫ After Starting .
▫ Electronic Stability Program (ESP) ......... 1 5 2 ▫ Synchronizing ESP .................... 1 5 3 ▫ ESP Control Switch .................... 1 5 4 ▫ Anti-Lock Brake System (ABS) ............ 1 5 5 ▫ Brake Pad Break-In .................... 1 5 8 䡵 Power Steering .
ST ARTING PROCEDURES W ARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. Be sur e that the parking brake is engaged and that selector lever is in the NEUTRAL or P ARK position (gearshift lever in Neutral).
NOTE: Due to the starter non-r epeat feature, the key must be turned completely to the left before attempting to start the engine again. Extremely Cold Weather (below -20°F or -29°C) For reliable st.
If the engine fails to start after you have followed the Normal Starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded.
Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. Be sure the transmission is in FIRST gear , (not THIRD), when starting from a stopped position. Damage to the clutch can result from starting in THIRD.
W ARNING! When leaving the vehicle, always remove the key from the ignition switch, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could move the gearshift lever , which could result in an accident or serious injury .
• Program mode selector switch • Accelerator position • V ehicle speed The gear shifting process is continuously adapted, de- pendent on the driving style, the driving situation and the road characteristics. The selector lever is automatically locked while in the P ARK position.
Maneuvering T o maneuver in tight areas, control the vehicle speed by gradually releasing the brakes. Accelerate gently and never abruptly step on the accelerator . T o rock a vehicle out of soft ground (mud or snow), alternately shift from forward to reverse, while applying only slight acceleration.
W ith a malfunction in the vehicle’s electrical system, the selector lever could remain locked in the P ARK position. T o unlock the selector lever manually , insert the end of the multipurpose tool from the glove box (or ball point pen) into the covered opening below the position “D” of the shift pattern.
Drive The transmission automatically upshifts thr ough fifth gear . The DRIVE position provides optimum driving characteristics under all normal operating conditions. AutoStick 姞 Gear selection The transmission gear can be selected by pressing the selector lever to the right or the left with the selector lever in the DRIVE position.
The delayed upshift is effective with vehicle speeds below 31 mph (50 km/h) at partial throttle and engine temperatures below 95°F (35°C). T o pr event the engine from laboring at low RPM when drivi.
Program mode selector switch The transmission is provided with a selector switch for Standard “S” and W inter/W et “W” (snow and ice) pro- gram modes. For standard mode, press the “S” symbol on the switch. Use this mode for all regular driving.
Emergency Operation (Limp Home Mode) If vehicle acceleration worsens, or the transmission no longer shifts, the transmission is most likely operating in Limp Home Mode which engages when there is a malfunction of the transmission. This condition may be accompanied by the CHECK ENGINE light in the instrument cluster coming on.
T o release the parking brake, slightly pull up the handle while pushing the lock button, and guide the lever downward to its stop. The brake warning light in the instrument cluster should go out. A warning sounds if you start to drive without having released the parking brake.
BRAKE SYSTEM Y our vehicle is equipped with power brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort requir ed to brake the vehicle will be much greater than that required with the power system operating.
Once the brake pedal is released, the BAS is deactivated. The malfunction indicator light for the BAS is combined with the Electronic Stability Program (ESP) malfunction indicator light.
Electronic Stability Program (ESP) The ESP enhances directional control and r educes wheel- spin under various driving conditions. When ESP is active, engine torque is limited and the ESP warning light starts to flash.
CAUTION! If the vehicle is towed with the front axle raised (see the What T o Do In Emergencies section in this manual), the engine must be shut off (key in the ignition switch turned to the OFF/LOCK or ACC position). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes.
ESP Control switch The ESP control switch is located in the center console. When the ESP is switched off, the warning light in the instrument cluster comes on.
Anti-Lock Brake System (ABS) The ABS gives incr eased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during sever e braking conditions to pr event wheel lock-up. The system operates to prevent wheel lock-up and help avoid skidding on slippery surfaces.
apparent on ice and snow . The anti-lock brake system pump motor makes a low humming noise during opera- tion, which is normal. W ARNING! Pumping of the brake pedal will diminish the effec- tiveness of the anti-lock brakes and may lead to an accident.
below 10 volts, the malfunction indicator light comes on and the ABS is switched off. When the voltage is above this value again, the malfunction indicator light should go out and the ABS is operational. If the malfunction indicator light stays illuminated, have the system checked at your authorized dealer as soon as possible.
Brake Pad Break-In The brakes on your vehicle do not require a long br eak-in period, but avoid repeated hard brake applications from high speeds during initial break-in. Also avoid severe brake loading such as may be encountered when de- scending long mountain grades.
TIRE SAFETY INFORMA TION See general tire safety information included in the “If Y ou Need Consumer Assistance” section of this manual. TIRES—GENERAL INFORMA TION Please take time to read the tire warranty booklet in your Owner’s Manual package.
2. Economy— Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will r educe tread life resulting in a need for earlier tir e replacement. Underinflation also increases tir e rolling resistance and results in higher fuel consumption.
CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pressure”.
W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
T read Wear Indicators T read wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Recommended T ire Inflation Pressures Sport Performance (Y speed rating) tires and All-Season Performance (W speed rating) tires Front 225/40 ZR18 ....
CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Check with your authorized dealer before replacing tires with a different size.
cannot be expected to function as a tire pressur e gauge. There can be a delay between the instant you adjust the air pressure in a tire and when the system updates the display . The TPMS is not intended to provide you with notification of rapid air loss.
the temperature is very cold. AL W A YS check the pressure in your tires if the TPMS T elltale lamp is illuminated. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
ORIGINAL EQUIPMENT TIRES Y our vehicle is equipped with either sport performance tires or all-season performance tires. The sport perfor- mance tires offer the maximum road handling capability in dry and wet weather conditions.
If you need snow tires, the recommended size for the front and rear tires is the same size as the original equipment front tir es. This size tir e on the rear allows the use of tire chains on the rear wheels.
Follow the r ecommended tire r otation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to r otation being per- formed.
FUEL REQUIREMENTS Y our engine is designed to meet all emis- sions regulations and provide satisfactory fuel economy and optimum performance when using high quality unleaded gaso- line having an octane rating of 91 or higher .
CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system com- ponents. Problems that result from using methanol/gasoline blends ar e not the r esponsibility of DaimlerChrysler Corporation and may not be covered by the Limited W arranty .
states adopting California emission standards, your ve- hicle will operate satisfactorily on fuels meeting Federal specifications, but emission control system performance may be adversely affected.
NOTE: The fuel tank filler tube has a restricting door about 2 inches (50 mm) down from the opening. If fuel is poured from a portable container , the container should have a flexible nozzle long enough to force open the restricting door . CAUTION! T o avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
VEHICLE LOADING The load carrying capacity of your vehicle is in the following chart and on the tire pressur e label attached to the driver door pillar . V ehicle Loading Capacities Front Seat Occupants ....................... 2 Cargo Capacity (with two persons) .
CAUTION! • T o prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof luggage rack which may come in contact with the roof panel.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................. 1 7 8 䡵 If Y our Engine Overheats ................ 1 7 8 䡵 TIREFIT T ire Repair And Jacking .......... 1 8 0 ▫ TIREFIT ............................ 1 8 0 ▫ Preparations For Jacking .
HAZARD W ARNING FLASHER The flasher switch is located in the console. Push in the flasher switch and all front and r ear dir ectional signals will flash. Press the flasher switch a second time to turn the flashers off. Do not use this emergency warning system when the vehicle is in motion.
NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it of f. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat.
TIREFIT TIRE REP AIR AND JACKING TIREFIT Small punctures, particularly those in the tread, can be sealed with TIREFIT . Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can be used in outside temperatures down to approximately -4°F (-20°C).
W ARNING! Cuts or punctures larger than approximately 0.16 in. (4 mm), tire damage caused by driving with extremely low tire pressure or on a flat tire, or a damaged wheel can pose a hazard while driving. TIREFIT should not be used in such circumstances.
1 1. T urn the ignition key to the ON/RUN position. 12. Press the switch on the air pump to 1. The air pump should start to inflate the tire. 13. After five minutes, the tire should be inflated to at least 26 psi (180 kPa) on the pressur e gauge.
Preparations for Jacking W ARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
• Block the wheel diagonally opposite the flat tire. • Passengers must not remain in the vehicle when the vehicle is jacked. NOTE: The jack is designed exclusively for jacking up the vehicle at the specified jack location points built beneath either side of the vehicle.
2. The lifting points for the jack are located beneath the outer edge of the body side, dir ectly behind the front wheel housings, and in front of the rear wheel housings.
NOTE: Do not raise the vehicle until you are sure the jack is securely engaged, as shown. 3. Holding the jack, insert the cradle under the lifting points. Crank the handle clockwise until the jack base meets the gr ound. Place the jack on firm gr ound.
W ARNING! A loose jack or tool thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and tools in the places provided. JUMP-ST ARTING THE BA TTER Y W ARNING! T ake care to avoid the radiator cooling fan whenever the hood is raised.
W ARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush contaminated area immedi- ately with large quantities of water .
3. T urn of f the heater , radio and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive jump-start attachment of the booster battery . Connect the other end of the same cable to the positive jump-start attachment of the discharged battery .
T raction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability . T o reduce this possibility , the following precautions should be observed: 1.
TOWING A DISABLED VEHICLE W e recommend that the vehicle be transported using flat bed equipment. This method is preferable to other types of towing. CAUTION! Important! If towing the vehicle, please .
CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flatbed truck.
Insert the tool (or similar sized screwdriver) into the slot in the grille as shown (the tool must be inserted far enough to engage the clip on the left side of the grille). Push the tool to the left to disengage the clip and detach the grille. The front towing eye is now accessible.
T ow-Away Alarm Once the alarm system has been armed, the exterior vehicle lights will flash and an alarm will sound when anyone attempts to raise the vehicle for towing. The alarm will last approximately three minutes in the form of flashing exterior lights.
CONVERTIBLE TOP EMERGENCY OPERA TION If the convertible top cannot be closed using the convert- ible top switch, check the following: • Is the decklid closed properly? • Is there sufficient battery voltage? Start the engine if necessary .
Relieving Hydraulic Pressure NOTE: The hydraulic pressure must be relieved before the top can manually be raised or lowered. 1. T urn the ignition to the “ON” position. 2. Push down on the convertible top switch and hold in that position. 3. T urn the ignition “OFF” and continue to push down on the switch for 5 seconds.
3. Unlock the storage compartment by placing the tool on the bolt between the backrest and the tonneau cover . T urn the wrench in the direction of the arrow to its stop and remove the tool. 4. Open the tonneau cover and secure it in the upright position.
6. Move the convertible top toward the windshield header . W ARNING! Do not place your hands in the convertible top frame areas. Serious personal injury may occur . 7. Do not place the convertible top frame onto wind- shield header . 8. Place the r ear window section of the convertible top in its vertical position.
10. Lock the convertible top storage compartment by placing the tool on the bolt between the backrest and the tonneau cover . T urn the wrench in the direction of the arrow to its stop and remove the tool. 1 1. Lower the rear window section of the convertible top down and lock into the tonneau cover .
12. Fold down the locking latch handle. 13. T urn the latch handle just past one quarter turn clockwise and pull the convertible top frame carefully down until it meets the windshield header attachment points. 14. T urn the latch handle counterclockwise to the stop in order to lock the convertible top.
Opening a Locked Decklid It is possible for the decklid to become locked if a convertible top system malfunction occurs. If the top is manually moved to the full up or full down position when the hydraulic pressure is relieved, the decklid should unlock.
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 3.2L Engine .......................... 2 0 5 䡵 Onboard Diagnostic System (OBD II) ....... 2 0 6 䡵 Emissions Inspection And Maintenance Programs ............................ 2 0 7 䡵 Replacement Parts .......
▫ Manual T ransmission .................. 2 2 9 ▫ Appearance Care And Protection From Corrosion ........................... 2 3 0 䡵 Convertible T op Care ................... 2 3 4 ▫ W ashing ............................ 2 3 5 ▫ General Cleaning .
3.2L ENGINE MAINT AINING YOUR VEHICLE 205 7.
ONBOARD DIAGNOSTIC SYSTEM (OBD II) T o meet new government regulations and pr omote cleaner air , your Crossfir e is equipped with a sophisti- cated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle’s emissions control system.
If your OBD system is not ready , you should see your authorized dealer or r epair facility . If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent technician.
The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Change Engine Oil The oil change interval for your Crossfir e is initially set at 7,000 miles (Canada: 1 1,000 km). The Flexible Service System (FSS) in your vehicle evalu- ates engine temperature, oil level, vehicle speed, engine speed, distance driven, and the time elapsed since your last service.
Engine Oil Selection For best performance and maximum protection under all types of operating conditions, only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W -40. The FSS may not alert for an oil change at the proper interval if an unapproved engine oil is used; engine damage and reduced engine life may result.
Drive Belts - Check Condition and T ension At the distance shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure.
Catalytic Converter The catalytic converter requires the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not requir e maintenance.
• Do not idle the engine with any spark plug wires disconnected for a prolonged period. Ignition Wiring System The ignition cables should be kept clean and properly connected. T erminals should be fully seated. Cracked, damaged, or faulty cables should be replaced.
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Power Steering Fluid No power steering fluid service is requir ed. The system is filled at the factory with Pentosin CHF 1 1S. Steering noise and reduced component life may result if an unappr oved fluid is used. During scheduled maintenance, check the power steering fluid level at the power steering fluid reservoir .
Chassis Lubrication Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated. Inspect these ball joints when- ever under-vehicle service is done. Steering Linkage Inspect tie r od ends whenever the vehicle is serviced.
Insert the key into the lock cylinder and rotate from the unlocked to the locked position without adding mor e lubricant. Repeat this procedur e thr ee or four times.
Windshield W asher Reservoir The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifr eeze) rated not to freeze at -25°F (-31°C).
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a pr operly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition key is in the ON position.
If the solution is dirty and contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner . Follow with a thor ough rinsing to remove all deposits and chemicals. Engine Coolant Disposal Used ethylene glycol based engine coolant is a regulated substance r equiring proper disposal.
Please note that it is the owner’s responsibility to main- tain the proper level of protection against fr eezing, according to the temperatures occurring in the ar ea where the vehicle is operated.
• If fr equent coolant additions are r equired, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks.
W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou wouldn’t have your full braking capacity in an emergency .
Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning light is on.
CAUTION! Do not allow petroleum-based fluid to contaminate the brake fluid as seal damage will result! Automatic T ransmission The fluid in the automatic transmission should be changed at 80,000 miles (129,000 km), along with the transmission fluid filter .
NOTE: Refer to Section 8 of this manual for Mainte- nance Schedules. Manual T ransmission Selection of Lubricant No fluid service is required. Use only fluid approved to MB 236.2. SAE 5W -20 engine oil, meeting API SL or GF-3, may be substituted. Refer to the Recommended Fluids, Lubricants and Genuine Parts section for the correct fluid type.
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body protection requirements vary according to geographic locations and usage.
CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose of f the undercarriage at least once a month.
When cleaning extremely dirty wheels, care must be taken in the selection of tire and wheel cleaning chemi- cals and equipment to prevent damage to the wheels. Only Mopar 威 Wheel Cleaners are recommended. Any of the “DO NOT USE” items listed below can damage wheels and wheel trim.
ammonia based cleaners to clean your leather upholstery . Application of a leather conditioner is not required to maintain the original condition. CAUTION! The use of vinyl, leather or plastic protectants may cause excessive gloss and/or discoloration of interior trim parts.
Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in the vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. • Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
W ashing CAUTION! • Remove bird droppings immediately . The organic acid can damage the material and cause the top to leak. • Never use a power washer to clean the top, as you may damage the top material. • If an automatic car wash is used, never use hot- wax.
The following methods are sufficient if the top is only lightly soiled: Dry Cleaning Brush the dry top with a soft-bristled brush from fr ont to rear of the vehicle. W et Cleaning W ash with clear water or with a mild detergent and an ample supply of luke warm water by wiping with a soft-bristled brush or sponge from fr ont to r ear .
FUSES Underhood Accessory Fuse Block Fuses The under hood accessory fuse block fuses are located under the hood on the driver’s side, between the brake master cylinder and the left front fender . T o r emove the lid, squeeze the tabs together located at the front of the fusebox.
CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow , it shows a problem in the circuit that must be corrected.
Underhood Accessory Fuse Block Fuses Cavity Fuse Circuits 1 5 Amp Beige Garage Door Opening Signal, TPM and Seat Heater 2 5 Amp Beige Occupant Restraint Controller Passenger Airbag Off 3 5 Amp Beige Indicator , Safety Restraint System and Indicator , Passenger Airbag Off 4 7.
Cavity Fuse Circuits 18 40 Amp Orange Electronic Stability Program 19 40 Amp Orange Power W indow , Front 20 30 Amp Green W iper Motor 21 30 Amp Green Seat Adjustment Right Side 22 30 Amp Green Seat A.
Relay Control Module Fuses The relay control module fuses are located in the Control Module Box next to the battery in the engine compart- ment. Slide the control module box cover retaining clips forward and lift the cover from the control module box to gain access to the relay control module fuses.
Interior Fuses The fuse access door is located on the end of the instrument panel on the driver’s side behind the trim panel cover . Use a coin or flat blade screwdriver to open and close this access door . Interior Fuses Cavity Fuse Circuits 1 Not Assigned 2 15 Amp Blue Brake Lamp/Speed Control 3 7.
Cavity Fuse Circuits 6 15 Amp Blue Right Low Beam 7 7.5 Amp Brown Right Parking/T ail Light Side Marker 8 15 Amp Blue Left Low Beam 9 15 Amp Blue Fog Light 10 7.
EXTERIOR LIGHT BULB SERVICE Headlights W ARNING! Halogen lamps contain pressurized gas. A bulb can explode if you: • T ouch or move it when hot • Drop the bulb • Scratch the bulb W ear eye and hand protection. NOTE: T o prevent a possible electrical short circuit, switch off light prior to replacing a bulb.
Front T urn Signal and Parking/Standing Lights • T wist the bulb socket counterclockwise and pull out. Push the bulb into the socket, turn counterclockwise and remove. • Replace the bulb, push in and twist clockwise. Rein- stall the socket, and turn clockwise.
4. Replace the access door in the trim panel. License Plate Light 1. Remove the two lens assembly mounting screws. 2. Pull the bulb out of the socket. 3. Replace the bulb and reattach the lens assembly . 4. Align and resecur e the two lens assembly mounting screws.
the vehicle and then r eadjust the headlights to the original position. If any further adjustments are neces- sary contact your manufacturer’s dealer . A detailed ser- vice procedur e is contained in the manufacturer’s Service Manual. Information on purchasing a Service Manual can be found at the back of this Owner’s Manual.
Check the battery every four to six weeks to ensure that the voltage is above 12.40. V oltage will drop more rapidly in hot temperatures. If battery voltage drops below 12.40, follow the battery recharge procedure in the Service Manual. • Check that the radiator coolant level of protection is to at least -20°F (-29°C).
SPECIFICA TIONS Engine Specifications Engine Size 195.2 CID (3.2 Liters) Mode of Operation 4–stroke engine, gasoline injection No. of Cylinders 6 Horsepower (SAE J 1349) 215 hp (160 kW) @ 5700 rpm Bore 3.54 in. (89.90 mm) Stroke 3.30 in. (84.00 mm) T orque (SAE J 1349) 229 ft.
Body Specifications Overall Length 159.8 in. (4058 mm) Maximum W idth 69.5 in. (1766 mm) Maximum W idth W ith Mirrors 76.9 in. (1954 mm) Overall Height Coupe: 51.5 in. (1307 mm) Roadster: 51.8 in. (1315 mm) Front T rack 58.8 in. (1493 mm) Rear T rack 59.
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 15.8 Gallons 60.0 Liters Fuel T ank Reserve 2 Gallons 7.5 Liters Engine Oil (with filter) 3.2 L Engine 8.5 Qts. 8.0 Liters Cooling System * 3.2 L Engine 1 1.8 Qts. 1 1.2 Liters Manual T ransmission 1.9 Qts.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Use coolant approved to MB 325.0, such as V alvoline GO5, or an equivalent extended life coolant. Engine Oil Only use synthetic engine oils, approved to MB 229.
Chassis Component Fluids, Lubricants and Genuine Parts Automatic T ransmission Only use A TF approved to MB 236.10, MB 236.12. Synthetic Dexron III 威 T ransmission Fluid may be substituted.
Body Component Fluids, Lubricants and Genuine Parts Hinges: Door Mopar 威 Spray White Lube Liftgate / Decklid Mopar 威 Multi-Purpose Lube NLGI Grade 2 EP , GC-LB Hood Springs and Links Mopar 威 Spr.
MAINTENANCE SCHEDULES CONTENTS 䡵 Introduction .......................... 2 5 6 䡵 W arranty ............................ 2 5 6 䡵 Emission Control System Maintenance ...... 2 5 7 䡵 Maintenance Schedules .................. 2 5 7 ▫ Scope Of W ork For “A” Schedule Maintenance Service .
INTRODUCTION This is intended as a guide to the service requirements of your vehicle. It contains all necessary instructions concerning service intervals and operations which have to be carried out. Scope and frequency of maintenance work primarily depend on the vehicle’s operating conditions.
The use of Special lubricant additives is not recom- mended. The use of such additives may affect your warranty rights. W ith regard to legal stipulations con- cerning emissions control, please note that engines have to be serviced and adjusted in accordance with special instructions and using special measuring equipment.
Y our Flexible Service System (FSS) — see Understanding Y our Instrument Panel section — should give you an exact indication of when your vehicle should be sched- uled for service and which schedule to follow .
SCOPE OF WORK FOR “B” SCHEDULE MAINTENANCE SERVICE Oil Change • Change oil and replace filter Maintenance • Rotate tires • Replace dust filter (if equipped) • Lubricate hood hinges, latch,.
Fluid Levels Check fluid levels for the following systems and corr ect if necessary . Should there be a loss of fluid that cannot be explained by regular use, trace and eliminate the cause.
The next service is normally calculated and displayed next to the Service A or Service B symbol as distance remaining before the next service is requir ed. Depending on operating conditions through- out the year , a clock symbol may appear next to the service symbol.
At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut of f. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level r eading.
At approximately every 50,000 miles (80,000 km) or 4 years: • Check condition of driveshaft flex discs. • Retighten locking bolts for steering (observe torque). At approximately every 60,000 miles (96,000 km) or 4 years: • Replace fuel filter . • Replace air cleaner filter element.
SPECIAL MAINTENANCE REQUIREMENTS Coolant Have the corrosion inhibitor/antifreeze concentration in the coolant checked before the onset of winter (once a year in countries with high prevailing temperatures). Have the coolant replaced every five years or 100,000 miles (160,000 km).
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 2 6 6 ▫ Prepar e For The Appointment ............ 2 6 6 ▫ Prepar e A List ........................ 2 6 6 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be cover ed by the warranty; discuss additional charges with the service manager .
This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the DaimlerChrysler Corporation has installed special TDD (T elecommunication Devices for the Deaf) equip- ment at its Customer Center .
W ARRANTY INFORMA TION See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available fr om your authorized dealer .
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
TIRE SAFETY INFORMA TION Tire Markings T ire Sizing Chart NOTE: P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H.
EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ...blank... ⴖ = Passenger car tire based on European design standards LT = Light T ruck tire based on U.
Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and Tire Pressure T ire Placard Location NOTE: Some vehicles have a “T ire and Loading Infor- mation” placard located on the driver’s side “B” pillar . T ire and Loading Information Placard This placard tells you important information about: 1.
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
278 IF YOU NEED CONSUMER ASSIST ANCE.
W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them.
.
INDEX 10.
ABS (Anti-Lock Brake) System ............. 1 1 1 Adding Engine Coolant (Antifreeze) ......... 2 2 3 Adding Fuel .......................... 1 7 3 Aiming Headlights ...................... 2 4 6 Air Cleaner , Engine (Engine Air Cleaner Filter) . 213 Air Conditioning .
Carbon Monoxide W arning ................ 4 7 Cargo Compartment Capacity ............................ 1 7 5 Catalytic Converter ..................... 2 1 4 CD Player ......................... 1 19,123 Chains, T ire ........................... 1 6 7 Changing A Flat T ire .
Disposal Engine Oil .......................... 2 1 2 Door Locks, Automatic ................... 1 3 Drive Belts ............................ 2 1 3 Drive Shaft Universal Joints ............... 2 1 8 Driving On Slippery Surfaces .................. 1 8 9 Electronic Speed Control .
Fuses ................................ 2 3 7 Garage Door Opener ..................... 9 7 G a sC a p .............................. 1 7 3 Gasoline ............................. 2 5 1 Gasoline/Oxygenate Blends ............... 1 7 1 Gear Ratios ........
Lights Airbag ........................... 32,1 16 Anti-Lock W arning .................... 1 1 1 Back-Up ............................ 2 4 5 Daytime Running ...................... 7 7 Exterior ............................. 7 6 Exterior Check ...........
Mopar Parts ........................ 208,269 Multi-Function Control Lever ............... 7 8 Occupant Restraints ...................... 2 2 Oil, Engine ........................... 2 0 9 Change Interval ...................... 2 1 1 Checking ..........
Safety Checks Inside V ehicle ............... 4 8 Safety Checks Outside V ehicle .............. 4 8 Safety Information, T ire .................. 1 5 9 Safety T ips ............................. 4 7 Schedule, Maintenance ................... 2 5 7 Seat Belts .
Alignment .......................... 1 6 5 Chains ............................. 1 6 7 Changing ........................ 180,184 General Information ................... 1 5 9 High Speed ......................... 1 6 1 Inflation Pressures ..............
W asher , Adding Fluid ................... 2 2 0 W ashing V ehicle ........................ 2 3 0 Wheel Alignment and Balance ............. 1 6 5 Wheel and Wheel T rim Care ............... 2 3 1 W indows Power .............................. 2 1 W indshield Defroster .
NOTES.
NOTES.
NOTES.
NOTES.
NOTES.
NOTES.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Chrysler Crossfire (2006) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Chrysler Crossfire (2006) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Chrysler Crossfire (2006), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Chrysler Crossfire (2006) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Chrysler Crossfire (2006), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Chrysler Crossfire (2006).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Chrysler Crossfire (2006). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Chrysler Crossfire (2006) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
