Manuel d'utilisation / d'entretien du produit Chevy Impala SS LSD du fabricant Chevrolet
Aller à la page of 33
1 50061011 Chevy Impala SS A Division of KW automotive North America, Inc CHEVY IMP ALA 1992 - 1996 LSD INST ALLA TION.
2 50061011 Chevy Impala SS A Division of KW automotive North America, Inc.
3 50061011 Chevy Impala SS A Division of KW automotive North America, Inc INST ALLA TION INTRODUCTION 1. REMOVING THE FENDER, DOORS FROM THE A-PILLAR AND DISCONNECTING THE WIRE HARNESS @ THE DOOR JAM 2. REMOVING THE EXISTING DOOR HI NGES FROM THE DOORS; TOP AND BOTTOM.
4 50061011 Chevy Impala SS A Division of KW automotive North America, Inc Inst allation Instructions LamboSty leDoors (The instructions are to be used as a refe rence only.
5 50061011 Chevy Impala SS A Division of KW automotive North America, Inc LSD Doors must be installed according to the provided vehicle specific instructions fr om LSD Do ors and in- stallation should be performed by an authorized dealer.
6 50061011 Chevy Impala SS A Division of KW automotive North America, Inc An additional inside support handle must be installed to so lve the issue of possible difficulty of griping the door, when raising and lowering your door from your seated position.
7 50061011 Chevy Impala SS A Division of KW automotive North America, Inc - After washing the vehicle, open the doors and check to see that all piv ot points are properly greased - Every three months,.
8 50061011 Chevy Impala SS A Division of KW automotive North America, Inc 1x A 5X B 1x C 3x D Snap ring Cable ties Gas Damper 2450 M.A.R.A Shim 1x E 1x F 1x G 2x H LSD Swing Arm LSD Ground Plate LS D .
9 50061011 Chevy Impala SS A Division of KW automotive North America, Inc C C OEM A A C OEM OEM OEM F E.
10 50061011 Chevy Impala SS A Division of KW automotive North America, Inc ORIGINAL EQUIPMENT CHAS SIS HINGE REMOVAL MODIFICATI ON IMPORTANT NOTE: The following instructions given, in sequential order, is a step-by-step procedure to minimize any installation difficulty that may occur.
11 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 1 INNER FENDER MODIFICATION For this particular application, once the outer fender has been removed, the inner fender needs to be modified, to accommodate the new LSD hinges.
12 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 1 INNER FENDER MODIFICATION –cont’d- For this particular application, once the outer fender has been removed, the inner fender needs to be modified, to accommodate the new LSD hinges.
13 50061011 Chevy Impala SS A Division of KW automotive North America, Inc PHOTO 3 STEP 1 INNER FENDER MODIFICATION –cont’d- For this particular application, once the outer fender has been removed, the inner fender needs to be modified, to accommodate the new LSD hinges.
14 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 2 INNER FENDER MODIFICATION –cont’d- For this particular application also, the outer fender also needs to be modified, to accom- modate the new LSD hinges. The following pictures show the areas (outlined in wh ite) that will need to be removed.
15 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 3 DIS-ASSEMBLING THE SWING ARM FROM THE GROUND PLATE 3a. Your new LSD Door Hinges have come assembled. 3b. As identified in ( Photo 8 ), disassemble the swing arm from the ground plate.
16 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 4 MOUNTING THE GROUND PLATE TO THE A- PILLAR 4a. Using the kit supplied mounting hardware for the Ground Plate, attach it t o the A-Pillar. Finger tight initially, then using a wrench, torque to specifications.
17 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 5 MODIFYING THE CHASSIS WIRING HARNESS IMPORTANT NOTE: Prior to beginning extending the wiring harness from the A-pillar, each individual wire needs to be cut one at a time.
18 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 5 MODIFYING THE CHASSIS WIRING HARNESS –cont’d- 5g. VERY IMPORTANT: 5h. Remember to stagger the cuts for each individual wire. This will eliminate having a large wrap and will allow for minimal size and maximum flexibility.
19 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 5 ROUTING THE WIRE H ARNE SS IMPORTANT NOTE: 5n. Prior to mounting the Swing Arm to the door, the wire harness needs to .
20 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 6 MOUNTING THE LSD SWING ARM 6a. Using the existing O.E.M. nuts, mount the LSD swing arm on the door, matching up each respective mount hole. Two mount holes at the top and two at the bottom ( Photo 15 ).
21 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 7 MOUNTING THE DOOR TO THE A-FRAME IMPORTANT NOTE: THIS STEP S HOULD BE DONE WITHOUT THE GAS S PRING INSTALLED 7a. Place the door back on the vehicle and close the door completely.
22 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 8 MOUNTING THE GAS DAMPER (after correct gap distance has been established) IMPORT ANT NOTE: • PRIOR TO MOUNTING THE GAS DAMPER AT ITS RESPECTIVE MOUNTING POINTS, WE HIGHLY RECOMMEND USING AN A NTI-RUST LUBRICANT, WIPING D OWN THE MOUNT POINTS TO PRE - VENT RUSTING.
23 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 8 MOUNTING THE GAS DAMPER (after correct gap distance has been established) 8a. Hang (mount) the gas damper on the mount point of the swing arm ( Photo 22 ). Secure it with the kit supplied security ring, by using needle-nose pliers.
24 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 9 FINAL DOOR ADJUSTMENT… IF REQUIRED 9a. With the gas spring installed 9b. At this point of the installation, open and close the door slowly. Check and see if the Magic Stick aligns correctly to the Magic Stick receptacle.
25 50061011 Chevy Impala SS A Division of KW automotive North America, Inc PHOTO 21 IF REQUIRED 9d. With the gas spring uninstalled. 9e. If spacer (s) installation is needed, install one at a time, starting at the top , ( Photo 21 ) working your way to the bottom, to see if that particular spacer aligns the door correctly.
26 50061011 Chevy Impala SS A Division of KW automotive North America, Inc STEP 10 ROUTING THE WIRE HARNE SS 10a. Pivot the door carefully up and make sure there is sufficient clearance on the fender , A- pillar and hood. If necessary, adjust the Ground plate or the LSD swing arm again.
27 50061011 Chevy Impala SS A Division of KW automotive North America, Inc 11. ROLLER ADJUSTMENT NOTE: The door needs to be in the closed position for this adjustment to be properly done. 11a. Please adjust the slide roller so the LSD swing arm has the initial contact and pre- load while opening and closing of the door.
28 50061011 Chevy Impala SS A Division of KW automotive North America, Inc COMMON TROUBLESHOOTING QUESTIONS and ANSWERS Q1: WHY DOES THE BOTTOM OF THE DOOR NOT SIT FLUSH, AT THE FRONT OR REAR?: A1 : LSD door hinges are engineered and designed to compensate for this issue.
29 50061011 Chevy Impala SS A Division of KW automotive North America, Inc.
30 50061011 Chevy Impala SS A Division of KW automotive North America, Inc.
31 50061011 Chevy Impala SS A Division of KW automotive North America, Inc.
32 50061011 Chevy Impala SS A Division of KW automotive North America, Inc.
33 50061011 Chevy Impala SS A Division of KW automotive North America, Inc.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Chevrolet Chevy Impala SS LSD c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Chevrolet Chevy Impala SS LSD - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Chevrolet Chevy Impala SS LSD, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Chevrolet Chevy Impala SS LSD va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Chevrolet Chevy Impala SS LSD, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Chevrolet Chevy Impala SS LSD.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Chevrolet Chevy Impala SS LSD. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Chevrolet Chevy Impala SS LSD ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
