Manuel d'utilisation / d'entretien du produit DMX-690 du fabricant Chauvet
Aller à la page of 23
Snapshot Ok on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle DMX-690 Intimidator S pot 2.0 HTI™ USER MANUAL Chauvet, 3000 N 2 9 th Ct, Hollywood, FL 3 3020 U.S.A. (800) 762-1084 – (954 ) 929-1115 FAX (954) 929-5560 www.
T ABLE OF C ONTENTS 1. BEFORE YOU BEGIN ....................................................................................................................................................... 3 W HAT IS INCLUDED .......................................
1. B EFORE Y OU B EGIN What is included ¾ 1 x Intimidator Spot 2.0 HTI™ ¾ 150W HTI Lamp ¾ Power Cord ¾ W arranty Card ¾ User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. • Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that the y also receive this instruction booklet.
2. I NTRODUCTION Features • 6 to 8-channel DMX-512 moving yoke • Pan: 540° / tilt: 270° • Variable strobe/shutter • Color wheel: 7 colors + white Rainbow color spin effect • Rotating gobo .
Product Overview Control Panel DMX Output Connector Yoke Rear of Base AC Power Input & F use H o l der Easy Controller Connector DMX Input Connector Base Head Focusing Lens Voltage Selector Sw itch Intimidator Spot 2.
3. S ETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. A 150W HTI lamp is included. Warning! When replacing th e lamp, please wait 15 minutes after p owering down to allow th e unit to cool down! Always disconnect from main power prior to lamp replacement.
Lamp Alignment How- To Often, after a new installation of a lamp, you will fi nd that there is an uneven fiel d of light or what is refered to as a hot spot. This is due to the most intense point of the lamp source not being positioned optimally within the reflector.
Replacing Gobos 1) Remove the four screws indicated in figure A to remove the back of the head. Figure A Figure B Figure C Figure D 2) Remove the four screws indicated in figure B to remove the front of the head. 3) Orient the fixture so that it looks like the fixture in figure C.
Fixture Linki ng You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixt ures set to a master/slave operating mode.
3-PIN TO 5-PIN CON VERSION CHART th a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. CHAUVET Model No: DMX5M , or DMX5F. 3 P IN TO 5 P IN C duc 3 Pin Female (output) 5 Pin .
Mounting ORIENTATION This fixture may be mounted in any position pr ovided there is adequate room for ventilation. RIGGING Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp.
4. O PERATING I NSTRUCTIONS Navigating the Control Panel Access control panel functions using the four pa nel buttons located directly underneath the LCD Display. NOTE: The display will turn off after 30 seconds if no buttons are pushed. MODE /ESC Button Function <MODE/ESC> Used to access the menu or to scroll through to p-level menu items.
Menu Map Intimidator Spot 2.0 HTI Manual 14 2007-01-24/09 :36.
Menu Functions User Configurations M ENU O PTION D ESCRIPTION DMX: The fixture will be controlled by a DMX signal coming from a DMX controller. The starting ad dress must be selected, and can be set using the up and down buttons.
TO CHANGE THE PAN RANGE : 1) Press <MODE/ESC> until , , or is displayed.. 2) Use the <UP> and <DOWN> buttons to scroll through the thre e opti ons. is 540°; is 360°; is 180° Note: These settings onl y apply if the fixture is in master/slave or stand-al one modes.
Operation Stand-Alone Mode ( Sound-Active, Auto Mode, E asy Controller): This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto Mode.
DMX Mode This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with DMX, please read the DMX Primer on page 21. 1) Press <MODE/ESC> until is displayed. 2) Use the <UP> and <DOWN> buttons to select the desired address a nd press the <ENTER> button.
DMX Channel Values (8-bit mode) C HANNEL V ALU E F UNCTION 1 000 Ù 255 Pan 0 – 540 (1 28 = halfway point) 2 000 Ù 255 Tilt 0 – 270 (1 28 = halfway point) 3 000 Ù 108 109 Ù 133 134 Ù 249 250 .
General Troubleshooting Applies to Symptom Solution(s) Lights Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check f an thermal switch reset 9 Beam is very dim or not bright Clean o.
Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A. ) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Pre ss 4) Fax: (954) 929-5560 - (Att ention: Service) Website: http://www.chauvetlighting.com 5.
Returns Proced ure Returned merchandise must be sent prepaid and in t he original packing, call tags will not be issued. Package must be clearly labeled with a Return Merc handise Author ization Number (RA #). Products returned without an RA # will be refused.
Technical Specifica tions WEIGHT & DIMENSIONS Length......................................................................................................................... ..... 16 in (406 mm) Width ..............................................
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Chauvet DMX-690 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Chauvet DMX-690 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Chauvet DMX-690, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Chauvet DMX-690 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Chauvet DMX-690, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Chauvet DMX-690.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Chauvet DMX-690. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Chauvet DMX-690 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
