Manuel d'utilisation / d'entretien du produit CG40 du fabricant Chamberlain
Aller à la page of 40
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .chamberlaingroup.com GARAGE DOOR OPENER Series CG40 1/2 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation.
2 Introduction 2-7 Safety symbol and signal word review ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning ............
3 Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver Adjustable End Wrench 1/2" and 7/16" Sockets and Wrench Drill Tape Measure 2 1 Stepladder Pencil 3/16", 5/16" and 5/32" .
Safety Reversing Sensor Support bracket & fastening hardware is required. See page 17. Door Center Header Wall FINISHED CEILING Torsion Spring Extension Spring OR Safety Reversing Sensor Gap betwe.
Access Door Gap between floor and bottom of door must not exceed 1/4" Safety Reversing Sensor Safety Reversing Sensor CLOSED POSITION Header Bracket Cable Pulley Bracket Door Bracket Straight Doo.
6 Cable Pulley Bracket 2-Conductor Bell Wire White & White/Red Lighted Door Control Button with (2) screws 6ABx1-1/2" Trolley Chain and Cable in Dispensing Carton Curved Door Arm Section Safe.
Hardwar e Inventory Separate all hardware and group as shown below for the assembly and installation procedures. 7 NOTICE Lock Washer 5/16" (4) Nut 5/16" - 18 (4) Clevis Pin 5/16"x2-3/4.
8 ASSEMBL Y STEP 1 Assemble the Rail and Attach the Cable Pulley Bracket To avoid installation difficulties, do not run the garage door opener until instructed to do so. 1. Align the four T -rail sections on a flat surface exactly as shown . Center sections are interchangeable.
9 ASSEMBL Y STEP 2 Install the T rolley • Attach the trolley threaded shaft to the trolley with the lock washer and nuts as shown. • As a temporary stop, insert a screwdriver into the hole in the front end of the T -rail. • Slide the trolley assembly along the rail to the screwdriver stop.
10 ASSEMBL Y STEP 4 Install the Chain/Cable and Attach the Sprocket Cover INST ALLING THE CHAIN/CABLE 1. Pull the cable loop from the carton and fasten it to the trolley with a master link from the hardware bag (see Figure 1). • Push pins of master link bar through cable loop and hole in front end of trolley .
ASSEMBL Y STEP 5 Tighten the Chain and Cable • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley . •T o tighten the chain, turn outer nut in the direction shown. AS YOU TURN THE NUT , KEEP THE CHAIN FROM TWISTING.
12 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centerline of the garage door .
13 Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling 2x4 OPTIONAL CEILING MOUNT FOR HEADER BRACKET Structural Supports ONE-PIECE DOOR WITHOUT TRACK 1. Close the door and mark the inside vertical centerline of your garage door .
14 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall.
Clevis Pin 5/16" x 2-3/4" Ring Fastener 15 INST ALLA TION STEP 3 Attach the T -Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help.
16 ONE-PIECE DOOR WITHOUT TRACK • With the door fully open and parallel to the floor , measure the distance from the floor to the top of the door . • Using a stepladder as a support, raise the top of the opener to this height. • The top of the door should be level with the top of the motor unit.
17 INST ALLA TION STEP 5 Hang the Opener T wo representative installations are shown. Y ours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before installing the opener .
18 To prevent possible SERIOUS INJURY or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires.
19 INST ALLA TION STEP 7 Install the Light and Lens INST ALL THE LIGHT • Install a 75 watt maximum light bulb in the socket. The light will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the light will turn OFF .
20 INST ALLA TION STEP 9 Electrical Requirements To avoid installation difficulties, do not run the opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
21 Invisible Light Beam Protection Area Sensor Beam 6" max. above floor Sensor Beam 6" max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction.
22 FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) DOOR TRACK MOUNT (RIGHT SIDE) Indicator light Lens Lip Sensor Bracket Door T rack Sensor Bracket Extension Bracket (See Accessories) Lens Indicator .
23 1/4"-20x1/2" Carriage bolt Lens Wing nut Figure 4 MOUNTING AND WIRING THE SAFETY SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor . Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door .
24 To prevent damage to garage door , reinforce inside of door with angle iron both vertically and horizontally . INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page.
25 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door , in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.
26 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley .
ALL ONE-PIECE DOORS 1. Assemble the door arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin.
28 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. To operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle.
ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction.
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested every month. • If one control (for ce or travel limits) is adjusted, the other control may also need adjustment.
OPERA TION 31 Using Y our Garage Door Opener Y our Security ✚ TM opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Security ✚ TM remote controls and one Security ✚ TM Keyless Entry System.
To Open the Door Manually DISCONNECT TROLLEY : The door should be fully closed if possible. Pull down on the emergency release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually .
33 Care of Y our Opener LIMIT AND FORCE ADJUSTMENTS: W eather conditions may cause some minor changes in door operation requiring some readjustments, particularly during the first year of operation. Pages 28 and 29 refer to the limit and force adjustments.
34 Having a Problem? (Continued) 6. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only .
LO C K L I G H T *Multi-Function Remotes If supplied with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ TM multi-function remote or mini-remote can be programmed to operate other Security ✚ TM garage door openers.
1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control.
7 U P C E I L I N G M O U N T O N L Y 9 10 11 NOTICE 5 6 8 1 4 12 13 3 2 1 3 3 6 7 4 5 5 8 2 Installation Parts 37 REP AIR P ARTS Rail Assembly Parts KEY P ART NO.
Motor Unit Assembly Parts 38 2 10 8 13 14 15 16 19 4 3 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 9 20 16 12 18 11 17 3 1 5 6 7 KEY P ART NO.
LOCK LIGHT L O C K L IG H T 39 ACCESSORIES 3-Button Security ✚ ™ Remote Control: Includes visor clip. SECURITY ✚ TM Keyless Entry: Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard.
©2003, The Chamberlain Group, Inc. 1 14A2490D All Rights Reserved Printed in Mexico CHAMBERLAIN GARAGE DOOR OPENER ONE-YEAR LIMITED W ARRANTY The Chamberlain Group, Inc.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Chamberlain CG40 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Chamberlain CG40 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Chamberlain CG40, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Chamberlain CG40 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Chamberlain CG40, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Chamberlain CG40.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Chamberlain CG40. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Chamberlain CG40 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
