Manuel d'utilisation / d'entretien du produit 6200-2 du fabricant Chamberlain
Aller à la page of 40
The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1 196 ® Complies with UL 324 Regulations effective January 1, Garage Door Opener Owner ’ s Manual For R.
Start by reviewing these important safety alert symbols: 2 Contents Page A review of safety alert symbols . . . . . . . . . . . . . .2 You'll need tools . . . . . . . . . . . . . . . . . . . . . . . . . .3 Safety information regarding garage door locks and ropes .
Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver Adjustable End Wrench 1/2" and 7/16" Sockets and Wrench Drill Tape Measure 2 1 Stepladder Pencil 3/16", 5/16" and 5/32&qu.
4 Y ou may find it helpful to refer back to this page as you proceed with the installation of your opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.
Safety Reversing Sensor FINISHED CEILING Support bracket & fastening hardware is required. See page 17. Slack in chain tension is normal when garage door is closed.
Cable Pulley Bracket 2-Conductor Bell Wire White & White/Red Trolley Door Bracket Header Bracket Hanging Brackets Chain and Cable in Dispensing Carton Curved Door Arm Section Straight Door Arm Sec.
Har d ware Separate all hardware from the packages in the rail carton and the opener carton as shown below, for the assembly and installation procedures.
8 Assembl y Step 1 Assemble the T -rail & Attach the Cab le Pulley Brac ket Hex Screws 5/16"-18x7/8" Cable Pulley Bracket Bracket & Rail Must Be Aligned Lock Washer 5/16&quo.
Hardware Shown Actual Size Assembl y Step 2 Install the T r olley on the T -rail • Place the opener on packing material to protect the cover. For convenience, put a support under the cable pulley bracket. • Remove the (2) 5/16"-18x1/2" washered screws mounted in the top of the opener.
Assembl y Step 4 Install the Chain/Cable & Attach the Spr ocket Co ver Opener Sprocket Install Chain & Cable Chamberlain '92 8/22/90 - 3/6/92 Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking.
• Spin the inner nut and lock washer down the threaded shaft, away from the trolley. • To tighten the chain, turn outer nut in the direction shown. As you turn the nut, keep the chain from twisting. • When the chain is approximately 1/2" above the base of the T-rail at its midpoint, re-tighten the inner nut to secure the adjustment.
• Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2" above the high point. This height will provide travel clearance for the top edge of the door. SECTIONAL DOOR CURVED TRACK ONE-PIECE DOOR WITH HORIZONTAL TRACK & JAMB HARDWARE The Chamberlain Group, Inc.
Door Highest Point of Travel Header Wall Pivot Distance Header Wall Highest Point of Travel Door Distance Jamb Hardware The Chamberlain Group, Inc.
Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door Mounting New Header Bracket 10/16/91 - 10/26/91 - 4/5/.
Header Bracket Temporary Support Header Wall Garage Door The Chamberlain Group, Inc. CGI - Attach Tee Rail to Header Bracket 2/4/92 - 4/9/92 - 5/3/92 -5/5/92 - 5/26/92 T-rail INCREASE T.
Installation Step 4 P osition the Opener Follow instructions which apply to your door type as illustrated. To prevent damage to steel, aluminum, fiberglass or glass panel doors, do not rest the opener on the door without using a 2x4.
Installation Step 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener.
18 Installation Step 6 Install the Multi-Function Door Control Panel 6ABx1-1/4" Screw Multi-Function Door Control Insulated Staples Dry Wall Anchors Screw 6-32x1" Hardware Shown Actual Size .
Lens Guide Lens Tab Lens Slot 75 Watt (Maximum) Light Bulb The Chamberlain Group, Inc. STEP 7 Install Lights and Lenses - CGI 10/7/91 - 5/2/92 - 5/26/92 Lens Slot 75 Watt Max. Light Bulb Lens Tab Light Lens Panel Screw Install the lights • Install a 75 watt maximum light bulb in each socket.
To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet.
The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. This is a required safety device and cannot be disabled. Installation procedures are the same for sectional and one-piece doors.
1/4 x 1-1/2" Lag Screw #10 - 32 x 3/8" Screw 1/4" - 20 Lock Nut #10 x 32 Lock Nut Staples 1/4" - 20 x 1/2" Carriage Bolts Installation Step 10 Install .
Invisible Light Beam Protection Area Sensor Sensor Connect Wire to Opener Terminals The Chamberlain Group, Inc. Attaching Sensor to "C" Wrap and Wires to Operator CGI 5/19/92.
Installation Step 11 Fasten Door Brac ket Follow instructions which apply to your door type as illustrated below or on page 25. To prevent damage to steel, aluminum, fiberglass or glass panel doors, always reinforce the inside of the door both vertically and horizontally with an angle iron.
All ONE-PIECE Door Installation Pr ocedure • Center the bracket on the top of the door, in line with the header bracket as shown. Mark holes. • Drill 5/16" pilot holes and fasten the door bracket with hardware supplied.
Installation Step 12 Connect Door Arm to T r olley Follow instructions which apply to your door type as illustrated below and on page 27. Make sure garage door is fully closed. Pull the manual release handle to disconnect the outer trolley from the inner trolley.
Door Arm to Trolley 1 pc 1/96 Nuts 5/16"-18 Lock Washers 5/16" Ring Fastener Straight Arm Screws 5/16"-18x7/8 Door Bracket Clevis Pin 5/16"x1-1/4" C.
Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety reversing sensors are completely installed. 28 Limit adjustment settings regulate the points at which the door will stop when moving up or down. The door will stop in the up direction if anything interferes with door travel.
Adjustment Step 2 Adjust the For ce Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door.
Adjustment Step 4 T est the Safety Rever se System Test: • Place a one-inch board (or a 2x4 laid flat) on the floor, centered under the garage door. • Operate the door in the down direction. The door must reverse on striking the obstruction. Adjustment: If the door stops on the obstruction, it is not traveling far enough in the down direction.
The remote control transmitter The opener must learn the code of any new remote control. Page 33 explains how to program your receiver and how to erase all codes if required. Self service of your receiver and remote control is not recommended. If service is needed, call the toll-free number listed on the back page.
32 Trolley Trolley Release Arm NOTICE Manual Release Handle (Pull Down) Trolley Trolley Release Arm NOTICE Manual Release Handle (Pull Down & Back Towards Opener) Weak or broken springs could allow an open door to fall (either rapidly or unexpectedly), resulting in serious injury, death or property damage.
Receiver and Remote Control Programming Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the door control or remote control transmitter.
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) 2. Have you disabled all door locks? Review installation instruction warnings on Page 11.
Having a Pr oblem? (continued) Situation Probab le Cause & Solution The opener strains or maxim um f or ce is needed to operate door: The door may be out of balance or the springs are broken. Close the door and use the manual release handle to disconnect the trolley .
7 UP CEILING MOUNT ONLY 9 10 11 NOTICE 5 6 14 13 12 15 8 1 4 3 2 LOCK LIGHT 2 1 3 3 4 5 5 6 7 RAIL GREASE NO. 83A4 8 Repair Parts Rail Assembly Parts Installation Parts 36 KEY P ART NO.
Repair Parts Opener Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 31D380 Sprocket cover 2 41C4220A Gear and sprocket assembly Complete with: Spring washer Thr ust washer Retaining ring Bearing plate .
LOCK LIGHT LOCK LIGHT Accessories A vailable for your Opener 953CB 7702CB SECURITY ✚ Multi-Function Remote Control: Includes visor clip. Outside Quick Release: Required for a garage with NO access door . 8 foot Rail Extension Kit: T o allow an 8 foot door to open fully .
Index Access Door/Outside Quick Release Accessory ...........................................................................................4, 5 Chain Tension ...........................................................................................
CHAMBERLAIN SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SER VICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SIX DA YS A WEEK. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 HOURS: (Mountain Std. Time) 6:00 A.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Chamberlain 6200-2 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Chamberlain 6200-2 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Chamberlain 6200-2, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Chamberlain 6200-2 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Chamberlain 6200-2, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Chamberlain 6200-2.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Chamberlain 6200-2. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Chamberlain 6200-2 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
