Manuel d'utilisation / d'entretien du produit HN6840 du fabricant CDA
Aller à la page of 28
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
3 2004/108/EC. Parts intended to come into contact with food conform to 89/109/EC. IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC.
4 • Do not place hot lids flat on the hob top. A “ suction” eect could cause damage to the hob. • Do not drag cookware across the hob top: in the long term, this could cause damage to the hob. • Do not store cleaning or flammable products in the unit below the hob.
5 Important • Do not use the hob if the glass surface is cracked or damaged to prevent the risk of electric shock. Disconnect it from the power supply . • Ensure that the power cable of a connected electrical appliance near the hob is not in contact with the cooking zones.
6 Cooking On Induction The principle of induction cooking is based on magnetic eect. When you put your cookware on an induction zone and switch it on, the electronic boards in the hob produce induced currents in the base of the cookware and instantly raise its temperature.
7 Using Y our Hob Control Panel: Fig. 1 2 1 4 3 F Zones: 1. Front left 3. 7 kW 210mm 2. Back left 3. 7 kW 210mm 3. Back right 3. 7 kW 210mm 4. Front right 3.
8 The table below oers guidance as to what each power level is for . Using Y our Hob T o switch the hob on T o switch the power on, touch the “On/O ” key for appro ximately two seconds. The hob will beep and all four zone displays will show zero.
9 T o increase the power level for a zone, slide your finger along its slider (E) toward the right. T o reduce the power level for a zone, slide your finger along its slider (E) toward the left. T o turn the power o T o switch o a single zone, touch the left hand end of the slider (E) for the zone no longer required.
10 The symbols “ ” and “ ” against the power level displays for the 2 zones will go out and the zones will be independently controlled again. Pause function When one or more heating zones is active it is possible to pause all cooking temporarily without losing the settings for the individual zones.
11 Booster The hob is equipped with a booster function, allowing a higher power level than the maximum for appro ximately ten minutes. T o turn on the booster function, touch the booster key for the zone required. “ P ” will show in the display . T o cancel the booster at any time, touch anywhere along the slider for that zone.
12 Set the cooking duration using the “-“or “+” key individually within five seconds. T ouch and hold the “-“ or “+” key to scroll through the duration quickly . After five seconds, the dot in the timer display will start flashing and the countdown will start.
13 Note that if any of the cooking zones is in use, pressing the “-“ and “+” keys together several times will cycle the choice through the minute minder and the zones you are using. Set the time using the “-“or “+” key individually within five seconds.
14 Use of the key lock when the hob is in use The key lock LED is illuminated to confirm the key lock is switched on and no adjustments can be made to any of the zones or the timer . It is possible to switch o the hob using the On/O key when the key lock is on, for safety reasons.
15 removed from the zone, or is unsuitable for use on induction hobs. The zone display will show “ U” alternating with the power level until a suitable pan is placed on the zone. The zone will switch o after appro ximately one minute if no suitable pan is placed on the zone.
16 Ecient Use of Y our Hob The hob is equipped with zones of dierent sizes, designed to accommodate most shapes and sizes of pan. For best results, only use pans with flat bottoms and choose an appropriate zone depending on the size of the pan.
17 Care and Maintenance Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. Important: • S team cleaners must not be used when cleaning this appliance. • Y ou should use a non-abrasive cleaner to clean the hob top.
18 In the event of a fault with the hob, please advise CD A Customer Care of any fault code shown on the display Contact CD A Customer Care A: Customer Care Department, The CD A Group L td, Harby R oad, Langar , Nottinghamshire, NG13 9HY T: 01949 862 012 F : 01949 862 003 E : service@cda.
19 IMPORT ANT - PLEASE NOTE: In the event of any breakage , crack or cracking – even minimal – of the vitroceramic glass, immediately disconnect your appliance to prevent a risk of electric shock and contact CD A Customer Care.
20 Fitting the Hob Unpacking the hob: T ake care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 180mm away from any adjacent vertical surfaces, e.
21 the hood above the hob must be at least 600mm (650mm is recommended) (Fig. 4). If the instructions supplied with the hood dictate that the hood must be installed at a height greater than 600mm, then that height is the minimum required. W all furniture requirements: The minimum height of any cabinet immediately above the hob is 900mm.
22 How to Install the Hob: Overall dimensions of the hob: Width: 580 mm Depth: 510 mm W orktop cut-out dimensions: Width: 560 mm Depth: 490 mm 1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood to ensure that you will have the required clearance.
23 Mains Electricity Connection W arning! this appliance must be earthed W e recommend that the appliance is connected by a qualified electrician, who is a member of the N.
24 The following diagram shows the mains connection: When installing this product we recommend you seek the help of another individual. Appliance electrical rating: 7400W Any service call arising from incorrect installation may result in a charge. Fig.
25.
26.
27.
Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté CDA HN6840 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du CDA HN6840 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation CDA HN6840, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le CDA HN6840 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le CDA HN6840, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du CDA HN6840.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le CDA HN6840. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei CDA HN6840 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
