Manuel d'utilisation / d'entretien du produit OSHK80 du fabricant Simplicity
Aller à la page of 86
How to use this file...(Parts Manuals) ————————————————————————————————————————————––– Instructions for Print Vendors (Paper Manuals) Paper Size: * 11 x 17 * Body—50 lbs brilliant white offset or equivalent.
.
Parts Manual Rev. 09/2002 TP 400-2307-03-LW-S L ARGE F RAME S NOWTHROWERS (M ODELS 860, 970 & 1 180) M ODEL 860 S NOWTHROWERS Mfg. No. Description 1693650 860M, 8HP Snowthrower 1693651 860M, 8HP S.
.
1 TP 400-2307-03-LW-S T able of Contents SNOWTHROWER COMPONENTS P AGES Handles and Controls Group ....................................2 Engine & Frame Group - 8HP , Manual Start .........14 Engine & Frame Group - 8HP , Manual Start .........16 Engine & Frame Group - 8HP , Manual Start .
2 TP 400-2307-03-LW-S Handles and Controls Gr oup NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985771 The holes in the frame for Ref. 27 are slotted so the gear support (Ref. 42) can be positioned to ensure the inside surface of the gear support is tight against the hub of the front gear (Ref.
3 TP 400-2307-03-LW-S Handles and Controls Gr oup 1 1668525 1 CLUTCH ROD, Lower, RH 2 1669323 1 SPRING, Extension 3 1916621 4 NUT, Hex, #10-24 RH 4 1715659 2 CLUTCH ROD, Traction & Auger Drive 5 1.
4 TP 400-2307-03-LW-S Handles and Controls Gr oup NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985771 The above parts group applies to the following Mfg.
5 TP 400-2307-03-LW-S Handles and Controls Gr oup 50 916168 2 PIN, Spring 51 1960294 2 NUT, Hex Flange, 1/4-20 52 1960518 2 PUSH NUT, Bolt Retainer 1/4 53 1668526 1 CLUTCH ROD, Lower, LH 54 1707452 1 SPRING, Clutch Rod 55 1917372 1 NUT, Hex, 5/16-18 REF NO.
6 TP 400-2307-03-LW-S Handles and Controls Gr oup NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985916 The above parts group applies to the following Mfg.
7 TP 400-2307-03-LW-S Handles and Controls Gr oup 1 1668525 1 ROD, Auger, 3 7/16 Long 10-24 2 1669323 1 SPRING, Extension, 3 7/16 Long 3 1916621 1 NUT, Hex Machine Screw, 10-24 4 1715659 2 ROD, Clutch.
8 TP 400-2307-03-LW-S Handles and Controls Gr oup NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985916 The holes in the frame for Ref. 40 are slotted so the gear support (Ref. 37) can be positioned to ensure the inside surface of the gear support is tight against the hub of the front gear (Ref.
9 TP 400-2307-03-LW-S Handles and Controls Gr oup 50 1918452 2 PIN, Cotter 51 1918447 2 PIN, Cotter 52 1666255 1 ROD, Shift, 3/8 15 5/16 53 1916964 3 LOCKWASHER, Spring, 1/4 54 1916622 3 NUT, Hex, 1/2.
10 TP 400-2307-03-LW-S Handles and Controls Gr oup NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985643 The above parts group applies to the following Mfg.
11 TP 400-2307-03-LW-S Handles and Controls Gr oup 1 1667800 1 DASHBOARD 2 1935450 4 CAPSCREW, Hex Head, 1/4-20 x 3/4 3 1920397 4 NUT, Hex Lock, 1/4-20 4 1612165 1 HANDLE, Clutch, RH 5 1668608 2 GRIP .
12 TP 400-2307-03-LW-S Handles and Controls Gr oup NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985643 Linkage adjustment for traction and auger drive with power boost: with drive levers engaged, the bottom end of lower rods (Ref.
13 TP 400-2307-03-LW-S Handles and Controls Gr oup 50 1917372 1 NUT, Hex, 5/16-18 51 1664022 1 GROMMET 52 1930591 6 CAPSCREW, Hex Whiz Lock, 5/16-18 x 3/4 53 1718791 1 CABLE & HANDLE ASSEMBLY, Clutch (Includes Ref.
14 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Manual Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985633 Hook one end of spring (Ref. 15) into top hole of idler arm (Ref. 16) and other end into top hole of the idler arm assembly in the Traction Drive Group.
15 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Manual Start 1 1672732 1 BELT, Traction 2 1666655 1 BELT, Drive Auger 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
16 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Manual Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985634 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). Use 0-2 washers between Ref.
17 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Manual Start 1 1672732 1 BELT, Traction 2 1701257 1 BELT, Auger Drive 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
18 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Manual Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985634 The above parts group applies to the following Mfg. Nos.: 1693652 860DLX, 8HP Manual Start 1693653 860DLX, 8HP Manual Start (Export) © Copyright 2002 Simplicity Manufacturing, Inc.
19 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Manual Start 49 1702979 1 SPRING, Compression 50 ** 1 WICK, Oil 51 1702017 1 PULLEY, Drive 52 1701776 1 PULLEY, Drive 53 1922755 1 WASHER,13/32 .
20 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Manual Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985773 Export Only Hook one end of spring (Ref. 15) into top hole of roller arm (Ref. 16) and other end into top hole of the idler arm assembly in the Traction Drive Group.
21 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Manual Start 1 1672732 1 BELT, Traction 2 1666655 1 BELT, Drive Auger 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
22 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Electric Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 986111 Hook one end of spring (Ref. 15) into top hole of roller arm (Ref. 16) and other end into top hole of the idler arm assembly in the Traction Drive Group.
23 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Electric Start 1 1672732 1 BELT, Traction 2 1666655 1 BELT, Drive Auger 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
24 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Electric Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 986095 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). Use 0-2 washers between Ref.
25 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Electric Start 1 1672732 1 BELT, Traction 2 1701257 1 BELT, Auger Drive 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
26 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Electric Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 986095 The above parts group applies to the following Mfg. Nos.: 1694241 860DLXE, 8HP Electric Start © Copyright 2002 Simplicity Manufacturing, Inc.
27 TP 400-2307-03-LW-S Engine & Frame Group - 8HP , Electric Start 49 1702979 1 SPRING, Compression 50 ** 1 WICK, Oil 51 1702017 1 PULLEY, Drive 52 1701776 1 PULLEY, Drive 53 1922755 1 WASHER,13/3.
28 TP 400-2307-03-LW-S Engine & Frame Group - 9HP , Manual Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985635 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). Use 0-2 washers between Ref.
29 TP 400-2307-03-LW-S Engine & Frame Group - 9HP , Manual Start 1 1672732 1 BELT, Traction 2 1701257 1 BELT, Auger Drive 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
30 TP 400-2307-03-LW-S Engine & Frame Group - 9HP , Manual Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985635 The above parts group applies to the following Mfg. Nos.: 1693654 970M, 9HP Manual Start 1693655 970M, 9HP Manual Start (Export) © Copyright 2002 Simplicity Manufacturing, Inc.
31 TP 400-2307-03-LW-S Engine & Frame Group - 9HP , Manual Start 49 1702979 1 SPRING, Compression 50 ** 1 WICK, Oil 51 1702017 1 PULLEY, Drive 52 1701776 1 PULLEY, Drive 53 1922755 1 WASHER,13/32 .
32 TP 400-2307-03-LW-S Engine & Frame Group - 9HP , Electric Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 986098 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). Use 0-2 washers between Ref.
33 TP 400-2307-03-LW-S Engine & Frame Group - 9HP , Electric Start 1 1672732 1 BELT, Traction 2 1701257 1 BELT, Auger Drive 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
34 TP 400-2307-03-LW-S Engine & Frame Group - 9HP , Electric Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 986098 The above parts group applies to the following Mfg. Nos.: 1694243 970E, 9HP Electrical Start © Copyright 2002 Simplicity Manufacturing, Inc.
35 TP 400-2307-03-LW-S Engine & Frame Group - 9HP , Electric Start 49 1702979 1 SPRING, Compression 50 ** 1 WICK, Oil 51 1702017 1 PULLEY, Drive 52 1701776 1 PULLEY, Drive 53 1922755 1 WASHER,13/3.
36 TP 400-2307-03-LW-S Engine & Frame Group - 11HP , Manual Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985636 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). Use 0-2 washers between Ref.
37 TP 400-2307-03-LW-S Engine & Frame Group - 11HP , Manual Start 1 1672732 1 BELT, Traction 2 1701257 1 BELT, Auger Drive 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
38 TP 400-2307-03-LW-S Engine & Frame Group - 11HP , Manual Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985636 The above parts group applies to the following Mfg. Nos.: 1693656 1180M, 11HP Manual Start 1693657 1180M, 11HP Manual Start (Export) © Copyright 2002 Simplicity Manufacturing, Inc.
39 TP 400-2307-03-LW-S Engine & Frame Group - 11HP , Manual Start 49 1701849 1 SPRING, Compression 50 ** 1 WICK, Oil 51 1702017 1 PULLEY, Drive 52 1701776 1 PULLEY, Drive 53 1922755 1 WASHER,13/32.
40 TP 400-2307-03-LW-S Engine & Frame Group - 11HP , Electric Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 986099 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). Use 0-2 washers between Ref.
41 TP 400-2307-03-LW-S Engine & Frame Group - 11HP , Electric Start 1 1672732 1 BELT, Traction 2 1701257 1 BELT, Auger Drive 3 1667516 1 GUARD, Belt 4 1935255 2 NUT, Speed, 5/16-18 5 920426 2 LOCKWASHER, Ext.
42 TP 400-2307-03-LW-S Engine & Frame Group - 11HP , Electric Start NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 986099 The above parts group applies to the following Mfg. Nos.: 1694244 1180E, 11HP Electrical Start © Copyright 2002 Simplicity Manufacturing, Inc.
43 TP 400-2307-03-LW-S Engine & Frame Group - 11HP , Electric Start 49 1701849 1 SPRING, Compression 50 ** 1 WICK, Oil 51 1702017 1 PULLEY, Drive 52 1701776 1 PULLEY, Drive 53 1922755 1 WASHER,13/.
44 TP 400-2307-03-LW-S A uger and Impeller Group - 24” NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985466 End of hub to be flush with end of rolled down shaft (Ref. 9). Torque to 30 -34 ft-lbs. 40 - 46 Nm. Impeller to be positioned against bearing before tightening set screw.
45 TP 400-2307-03-LW-S A uger and Impeller Group - 24” 1 1679293 1 PULLEY, Auger Input 2 1928721 2 SETSCREW, Square Head, 5/16-18 x 1/2 3 1612187 1 IMPELLER ASSEMBLY 4 1960474 1 SETSCREW, Square Hea.
46 TP 400-2307-03-LW-S A uger and Impeller Group - 28” NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985467 End of hub to be flush with end of rolled down shaft (Ref. 9). Torque to 30 -34 ft-lbs. 40 - 46 Nm. Impeller to be positioned against bearing before tightening set screw.
47 TP 400-2307-03-LW-S A uger and Impeller Group - 28” 1 1679293 1 PULLEY, Auger Input 2 1928721 2 SETSCREW, Square Head, 5/16-18 x 1/2 3 1612187 1 IMPELLER ASSEMBLY 4 1960474 1 SETSCREW, Square Hea.
48 TP 400-2307-03-LW-S A uger and Impeller Group - 32” NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985468 End of hub to be flush with end of rolled down shaft (Ref. 9). Torque to 30 -34 ft-lbs. 40 - 46 Nm. Impeller to be positioned against bearing before tightening set screw.
49 TP 400-2307-03-LW-S A uger and Impeller Group - 32” 1 1679293 1 PULLEY, Auger Input 2 1928721 2 SETSCREW, Square Head, 5/16-18 x 1/2 3 1612187 1 IMPELLER ASSEMBLY 4 1960474 1 SETSCREW, Square Hea.
50 TP 400-2307-03-LW-S A uger Housing and Chute Group - 24” NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 983960 Coat top and bottom of chute ring with grease. Scraper blade should be on inside of housing. Plastic washer (Ref.
51 TP 400-2307-03-LW-S A uger Housing and Chute Group - 24” 1 1960126 2 PUSH NUT, 1/4 2 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4 3 960210 1 WASHER, Nylon 4 1919326 1 WASHER, Flat, 11/32 5 1670578 1 KN.
52 TP 400-2307-03-LW-S A uger Housing and Chute Group - 28” NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985639 OHV Coat top and bottom of chute ring with grease. Scraper blade should be on inside of housing. When installing cable, make sure it does not come into contact with muffler.
53 TP 400-2307-03-LW-S A uger Housing and Chute Group - 28” 1 1960126 4 PUSH NUT, 1/4 2 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4 3 960210 1 WASHER, Nylon 4 1919326 1 WASHER, Flat, 11/32 5 933126 1 WIN.
54 TP 400-2307-03-LW-S A uger Housing and Chute Group - 32” NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985640 OHV Coat top and bottom of chute ring with grease. Scraper blade should be on inside of housing. When installing cable, make sure it does not come into contact with muffler.
55 TP 400-2307-03-LW-S A uger Housing and Chute Group - 32” 1 1960126 4 PUSH NUT, 1/4 2 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4 3 960210 1 WASHER, Nylon 4 1919326 1 WASHER, Flat, 11/32 5 933126 1 WIN.
56 TP 400-2307-03-LW-S T raction Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985637 Mounted outside of frame. Mounted outside of frame. Mount to bracket in frame weldment. Pack groove with grease. Hook end to top left corner slot of frame.
57 TP 400-2307-03-LW-S T raction Drive Group 1 1925205 4 CAPSCREW, Hex Head, 5/16-18 x 5/8 2 1917356 11 LOCKWASHER, 5/16 3 1917372 10 NUT, Hex, 5/16-18 4 1667341 4 RETAINER, Bearing 5 1705897 4 BEARIN.
58 TP 400-2307-03-LW-S T raction Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985637 The above parts group applies to the following Mfg. Nos.: 1693650 860M, 8HP Manual Start 1693651 860M, 8HP Manual Start (Export) © Copyright 2002 Simplicity Manufacturing, Inc.
59 TP 400-2307-03-LW-S T raction Drive Group 50 1707002 1 SPRING 51 1919326 2 WASHER, Flat, 11/32 52 1700473 1 BELLCRANK REF NO. PART NO. QTY. DESCRIPTION Footnotes: The above parts group applies to the following Mfg.
60 TP 400-2307-03-LW-S T raction Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985772 Mounted outside of frame. Mounted outside of frame. Mount to bracket in frame weldment. Pack groove with grease. Hook end to top left corner slot of frame.
61 TP 400-2307-03-LW-S T raction Drive Group 1 1925205 4 CAPSCREW, Hex Head, 5/16-18 x 5/8 2 1917356 11 LOCKWASHER, 5/16 3 1917372 10 NUT, Hex, 5/16-18 4 1667341 4 RETAINER, Bearing 5 1705897 4 BEARIN.
62 TP 400-2307-03-LW-S T raction Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985772 The above parts group applies to the following Mfg.
63 TP 400-2307-03-LW-S T raction Drive Group 50 1707002 1 SPRING 51 1919326 2 WASHER, Flat, 11/32 52 1700473 1 BELLCRANK 53 1666106 1 BUSHING, Pivot 54 1922127 1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4 REF NO. PART NO. QTY. DESCRIPTION Footnotes: The above parts group applies to the following Mfg.
64 TP 400-2307-03-LW-S T raction Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985638 Mounted inside of frame. Mounted outside of frame. Grease I.D. teeth and flange. Be sure tie bar support is in place.
65 TP 400-2307-03-LW-S T raction Drive Group 1 1925205 4 CAPSCREW, Hex Head, 5/16-18 x 5/8 2 1917356 10 LOCKWASHER, 5/16 3 1917372 10 NUT, Hex, 5/16-18 4 1667341 4 RETAINER, Bearing 5 1705897 4 BEARIN.
66 TP 400-2307-03-LW-S T raction Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985638 The above parts group applies to the following Mfg.
67 TP 400-2307-03-LW-S T raction Drive Group 50 1919394 1 WASHER 51 8021010 1 SET COLLAR 52 1707002 1 SPRING 53 1918451 2 PIN, Cotter, 1/8 x 3/4 54 1666105 1 ROD, Pivot 55 1919438 3 NUT, Hex, Lock, 5/.
68 TP 400-2307-03-LW-S Decals Group - 860 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. D985670 1716532 y y W ARNING TO A VOID SERIOUS INJURY • Read Owner ’ s Manual before operating unit. • Never allow children to operate snowthrower .
69 TP 400-2307-03-LW-S Decals Group - 860 1 1715555 1 DECAL, Auger Control 1 1722640 1 DECAL, Auger Control (1693984 & 1693985) 2 1715557 1 DECAL, Speed Selector 3 1715556 1 DECAL, Warning / Main .
70 TP 400-2307-03-LW-S Decals G r oup - 860DLX, 970 & 1180 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. D985935 1716532 3 2 1 4 5 6 7 8 9 10 1 2 3 4 6 9 2 5 The above parts group applies to the following Mfg.
71 TP 400-2307-03-LW-S Decals G r oup - 860DLX, 970 & 1180 1 1714245 1 DECAL, Shift Pattern, RH 2 1720674 1 DECAL, Dash 2 1724078 1 DECAL, Dash 2 1722688 1 DECAL, Dash (Export) 3 1714246 1 DECAL, .
72 TP 400-2307-03-LW-S Wheels & Tires Gr oup - 860 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. W983851 3 5 6 2 4 1 The above parts group applies to the following Mfg.
73 TP 400-2307-03-LW-S Wheels & Tires Gr oup - 860 1 1714235 2 WHEEL & TIRE ASSEMBLY (Includes Ref. Nos. 2, 3 & 4) 2 1612000 2 TIRE, 4.80-4.00-8 3 1714242 2 HUB, Wheel 4 172353 2 VALVE STEM & CAP 5 153038 2 TUBE, Tire 6 1666969 2 KLIK-PIN REF NO.
74 TP 400-2307-03-LW-S Wheels & Tires Gr oup - 860DLX & 970 NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
75 TP 400-2307-03-LW-S Wheels & Tires Gr oup - 860DLX & 970 1 1921978 1 CAPSCREW, Hex Head, 5/16-18 x 2 2 1919438 1 NUT, Hex Lock ESNA Light, 5/16-18 3 172353 2 VALVE STEM & CAP 4 1714242 1 HUB, Wheel, RH 5 1612000 2 TIRE, 4.80-4.00-8 6 1714235 1 WHEEL & TIRE ASSEMBLY, RH (Includes Ref.
76 TP 400-2307-03-LW-S Wheels & Tires G r oup - 1180 & 1390 NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
77 TP 400-2307-03-LW-S Wheels & Tires G r oup - 1180 & 1390 1 1921978 1 CAPSCREW, Hex Head, 5/16-18 x 2 2 1919438 1 NUT, Hex Lock ESNA Light, 5/16-18 3 172353 2 VALVE STEM & CAP 4 1722762 1 HUB, Wheel, RH 5 1722597 2 TIRE, 16 x 6.50-6 6 1722599 1 WHEEL & TIRE ASSEMBLY, RH (Includes Ref.
78 TP 400-2307-03-LW-S Headlight Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 985652 Light mounting hardware is included with light.
79 TP 400-2307-03-LW-S Headlight Group 1 1921978 1 CAPSCREW, Hex Head, 5/16-18 x 2 2 1919438 1 NUT, Hex Lock ESNA Light, 5/16-18 3 172353 2 VALVE STEM & CAP 4 1714242 2(1) HUB, Wheel (860, 860DLX, 970 & 1180 Models) (Qty. 1 on 1180 Models) 4 1722762 1 HUB, Wheel, RH, (1180 & 1390 Models) 5 1722597 2 TIRE, (1180 & 1390), 16 x 6.
.
T orque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.
© Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA. MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Simplicity OSHK80 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Simplicity OSHK80 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Simplicity OSHK80, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Simplicity OSHK80 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Simplicity OSHK80, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Simplicity OSHK80.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Simplicity OSHK80. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Simplicity OSHK80 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
